[ 1 ]
Press and hold the button for three seconds in
order to switch the device's status.
Bitspower CPU Block Summit M Pro
with OLED (12th Gen Intel CPU)
instruction manual
Digital RGB PIN on 1motherboard or 2other equipment.
motherboard DRGB Multi Function Controller
(Not included)
BPTA-DRGBMFC
12
V2
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
OUT IN
72
W
T
240 S
0
50
99
TEM P
80. 6
W
T
240 S
0
122
192
TEM P
Water Temperature Line Graph
Input Voltage : DC 5V~12V
Temperature : 0~99° C(32~210.2° F)
operate current : <20ma
DRGB LED
A
LG
L
INTE 1700
INTEL LGA 2066
1700
[ 2 ]
Installation 1
Follow the right sequence to install.
Use an appropriate amount of thermal paste.
SCM3FL20
1mm Spacer
CPU Block
SCM4M3
Spring
[ 3 ]
Installation 2
Follow the right sequence to install.
The thumb screw cannot be locked too tightly, the spring
is slightly pressed and the gap is kept as shown below.
The thumb screw cannot be rotated to the end. When the
spring screws too tight, the SCM3H6 screw will be driven
and will be taken away from the motherboard, which will
cause the water block and CPU not to be closed well.
Thumb Screw
Spring
1mm Spacer
1mm Spacer
Back Pad
3M Paste Pad
Metal Backplane
M3x32mm Screw
CPU Block
SCM3H6 Thumb nut
[ 4 ]
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4 OUTIN
Installation 1
Follow the right sequence to install.
The thumb screw cannot be locked too tightly, the spring
is slightly pressed and the gap is kept as shown below.
The thumb screw cannot be rotated to the end. When the
spring screws too tight, the SCM3H6 screw will be driven
and will be taken away from the motherboard, which will
cause the water block and CPU not to be closed well.
Thumb Screw
Spring
1mm Spacer
1mm Spacer
Back Pad
3M Paste Pad
Metal Backplane
M3x32mm Screw
CPU Block
CPU Block PLATE(AM4)
SCM3H6 Thumb nut
[ 5 ]
Installation 2
Follow the right sequence to install.
Thumb Screw
1mm Spacer
CPU Block
SC6-32M3 Screw
Motherboard
Original backplane
Spring
[ 6 ]
For 1200/1700 Motherboard
Accessories
4
5
1 2
2
1
3
3
Washer
Thumb nut
Backplate
75MM
1.5MM
78MM
Adjusting Nut
Backplate Bolt
4 PCS
4 PCS
1 PC 5 PCS
4 PCS
BP-MKCPUM-1217
Assembly steps
step 1
[ 7 ]
step 3
step 2
4
5
Thumb Screw
Spring
CPU Block
1200/1700 Intel Motherboards
(Not included)
Notice
Before filling in the water, please make sure all the components are
installed correctly. To prevent any leakage which may damage the PC
components, please perform a 24-hour leaking test with only the pump
connected to the power supply.
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product
damage due to excessive pressure, the input pressure should not exceed
0.5kg/cm2 (Bar). If the product is damaged due to
excessive pressure, it will be borne by the customer. Forbidden to use the
leak teser when there is water in the loop or the pump is runing.
Bitspower requires to use of distilled or pure water or Bitspower Pellucid
Coolant as the water-cooling liquid. Also, the consumer can add Bitspower
Dye to Pellucid Coolant for the color requirement. But please do not add
any biocide by yourself. If the consumer chooses different water-cooling
liquids, the resulting impurities may cause peeling o the coating on some
of the hardware, water channels blockage by built-up residue, improper
operation of the water pump, water tank tube breakage, and O-rings
deformation or loss sealing leading to leakage. Any issues related to the
use of inappropriate water-cooling liquid will be the responsibility of the
consumer.
[ 8 ]
記得上角要放對應的 LOGO!
[ 9 ]
記得上角要放對應的 LOGO!
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
出 進
水溫 折線圖
輸入電壓：DC 5V~12V
顯示溫度：0~99° C(32~210.2° F)
工作電流：<20ma
使用說明書
輕觸此按鍵 ，輕觸此按鍵 3 秒， 進入模式切換狀態
72
W
T
240 S
0
50
99
TEM P
80. 6
W
T
240 S
0
122
192
TEM P
DRGB LED
請接 1主版或 2 其他設備的 DRGB 插槽
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
12
主版
Bitspower CPU Block Summit M Pro
with OLED (12th Gen Intel CPU) V2
A
LG
L
INTE 1700
INTEL LGA 2066
1700
[ 10 ]
核心需塗導熱膏
手轉螺絲
1 毫米墊片
冷頭
孔位固定螺絲
彈簧
請按照正確的順序安裝
安裝方式 1
[ 11 ]
手轉螺絲不能鎖太緊，彈簧略有壓迫且保有間隙如下圖。手轉
螺絲不能旋轉到底，當鎖太緊時，SCM3H6 螺絲會被帶動，並
會被帶離主板，反而導致冷頭與 CPU 貼合效果不好。 手轉螺絲
彈簧
1 毫米墊片
1 毫米墊片
背板墊片
3M 背膠絕緣片
金屬背板
M3x32 毫米螺絲
冷頭
SCM3H6 手轉螺絲
請按照正確的順序安裝
安裝方式 2
[ 12 ]
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4 出進
安裝方式 1
請按照正確的順序安裝
手轉螺絲不能鎖太緊，彈簧略有壓迫且保有間隙如下圖。手轉
螺絲不能旋轉到底，當鎖太緊時，SCM3H6 螺絲會被帶動，並
會被帶離主板，反而導致冷頭與 CPU 貼合效果不好。
手轉螺絲
彈簧
1 毫米墊片
1 毫米墊片
背板墊片
3M 背膠絕緣片
金屬背板
M3x32 毫米螺絲
冷頭
支架 (AM4)
SCM3H6 手轉螺絲
[ 13 ]
安裝方式 2
請按照正確的順序安裝
手轉螺絲
1 毫米墊片
冷頭
SC6-32M3 螺絲
主板
原廠背板
彈簧
[ 14 ]
適用於 1200/ 1700 主板
配件
4
5
1 2
2
1
3
3
墊片
墊高固定柱
背板
75MM
1.5MM
78MM
固定螺帽
背板螺絲
4 個
4 個
1 片 5 個
4 支
BP-MKCPUM-1217
組裝步驟
步驟 1
[ 15 ]
4
5
手轉螺絲
彈簧
冷頭
1200/1700 Intel 主機板 ( 不包括 )
步驟 2
步驟 3
注意
跑水前，請先確認所有零件已安裝在正確的位置上，在不開主機，單開水泵的
情况下，進行 24 小時的跑水測試， 確保無漏水情况後再開主機，避免發生漏
水而導致電腦零件的損壞。
本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品
顏色與配件以實物為準。
當使用測氣產品測試水路時 , 為避免由于壓力過大導致產品損壞 , 輸入的壓力
請不要超過 0.5kg/cm2 (Bar), 如因壓力過大造成產品損壞 , 將由客戶自行承
擔 . 嚴禁客戶在水路有水及水泵開啟的情況下進行氣體飽壓測試。
Bitspower 要求消費者使用 蒸餾水或純水或 Bitspower 透明冷卻液作爲水冷液
使用。此外，也可以添加 Bitspower 染料到透明冷卻液中以滿足顏色要求。如
果消費者選擇不同的水冷液，可能會引起水路配件中的塗層剝落、積垢堵塞水
道、水泵磨損、水箱管破裂、O 型圈變形或失去密封性導致漏水等。任何因使
用不當水冷液導致相關的問題將由消費者自行負責。
[ 16 ]
記得上角要放對應的 LOGO!
[ 17 ]
記得上角要放對應的 LOGO!
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
出 进
水温 折線圖
输入电压：DC 5V~12V
显示温度：0~99° C(32~210.2° F)
工作电流：<20ma
使用说明书
轻触此按键 ，轻触此按键 3 秒， 进入模式切换状态
72
W
T
240 S
0
50
99
TEM P
80. 6
W
T
240 S
0
122
192
TEM P
DRGB LED
主版
请接 1主版或 2 其他设备的 DRGB 插槽
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
12
Bitspower CPU Block Summit M Pro
with OLED (12th Gen Intel CPU) V2
A
LG
L
INTE 1700
INTEL LGA 2066
1700
[ 18 ]
核心需涂导热膏
固定水冷头手转式螺絲
1 毫米垫片
冷头
孔位固定螺丝
弹簧
请按照正确的顺序安装
安装方式 1
[ 19 ]
手转螺丝不能锁太紧，弹簧略有压迫且保有间隙如下图。手转
螺丝不能旋转到底，当锁太紧时，SCM3H6 螺丝会被带动，并
会被带离主板，反而导致冷头与 CPU 贴合效果不好。 手转螺丝
弹簧
1 毫米垫片
1 毫米垫片
背板垫片
3M 背胶绝缘片
金属背板
M3x32 毫米螺丝
冷头
SCM3H6 手转螺丝
请按照正确的顺序安装
安装方式 2
[ 20 ]
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4 出进
手转螺丝不能锁太紧，弹簧略有压迫且保有间隙如下图。手转
螺丝不能旋转到底，当锁太紧时，SCM3H6 螺丝会被带动，并
会被带离主板，反而导致冷头与 CPU 贴合效果不好。
手转螺丝
弹簧
1 毫米垫片
1 毫米垫片
背板垫片
3M 背胶绝缘片
金属背板
M3x32 毫米螺丝
冷头
支架 (AM4)
SCM3H6 手转螺丝
请按照正确的顺序安装
安装方式 1
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
