[ 1 ]
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
instruction manual
OUT IN
Digital RGB PIN on 1motherboard or 2other equipment.
motherboard
DRGB LED
DRGB Multi Function Controller
(Not included)
BPTA-DRGBMFC
12
A
LG
L
INTE 1700
INTEL LGA 2066
1700
Bitspower Premium Summit M Silver Moon
Limited Edition (Compatible with 1700) V2
[ 2 ]
Installation 1
Follow the right sequence to install.
Thumb Screw
1mm Spacer
CPU Block
SCM4M3
Spring
[ 3 ]
Follow the right sequence to install.
The thumb screw cannot be locked too tightly, the spring
is slightly pressed and the gap is kept as shown below.
The thumb screw cannot be rotated to the end. When the
spring screws too tight, the SCM3F6 screw will be driven
and will be taken away from the motherboard, which will
cause the water block and CPU not to be closed well.
Installation 2
Thumb Screw
Spring
1mm Spacer
1.2mm Spacer
Back Pad
3M Paste Pad
Metal Backplane
M3x32mm Screw
CPU Block
Thumb Nut
[ 4 ]
96
90
48
54
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4
OUT IN
Digital RGB PIN on 1motherboard or 2other equipment.
DRGB LED
DRGB Multi Function Controller
(Not included)
BPTA-DRGBMFC
12
motherboard
[ 5 ]
Follow the right sequence to install.
Thumb Screw
Spring
1mm Spacer
1.2mm Spacer
Back Pad
3M Paste Pad
Metal Backplane
M3x32mm Screw
CPU Block
CPU Block PLATE(AM4)
Thumb Nut
The thumb screw cannot be locked too tightly, the spring
is slightly pressed and the gap is kept as shown below.
The thumb screw cannot be rotated to the end. When the
spring screws too tight, the SCM3F6 screw will be driven
and will be taken away from the motherboard, which will
cause the water block and CPU not to be closed well.
Installation 1
[ 6 ]
Installation 2
Follow the right sequence to install.
Thumb Screw
1mm Spacer
CPU Block
SC6-32M3 Screw
Motherboard
Original backplane
Spring
[ 7 ]
105
46
AMD SOCKET TR4
AMD SOCKET TR4
65.2
X399
OUT IN
Digital RGB PIN on 1motherboard
or 2other equipment.
DRGB LED
DRGB Multi Function Controller
(Not included)
BPTA-DRGBMFC
12
motherboard
[ 8 ]
Follow the right sequence to install.
Installation
Thumb Screw
1mm Spacer
CPU Block
SCM4M3
CPU Block PLATE(X399)
Spring
[ 9 ]
Assembly steps
Accessories
4
1 2
3
Washer
Backplate
78MM
1.5MM
92.56MM
Adjusting Nut
Backplate Bolt
4 PCS
1 PC 8 PCS
4 PCS
Assembly steps
step 1
1
2
3
For LGA 1700 Motherboard
BPTA-MKCPUMS-1700
記得上角要放對應的 LOGO!
[ 10 ]
step 3
step 2
4
2
Thumb Screw
Spring
CPU Block
LGA 1700 Intel Motherboards
(Not included)
Notice
Before filling in the water, please make sure all the components are
installed correctly. To prevent any leakage which may damage the PC
components, please perform a 24-hour leaking test with only the pump
connected to the power supply.
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product
damage due to excessive pressure, the input pressure should not exceed
0.5kg/cm2 (Bar). If the product is damaged due to
excessive pressure, it will be borne by the customer. Forbidden to use the
leak teser when there is water in the loop or the pump is runing.
Bitspower recommends that consumers use the Bitspower Pellucid
Coolant for their water-cooling liquid. Also, they can add Bitspower Dye
to Pellucid Coolant for the color requirement. If the consumer chooses
dierent water-cooling liquids, the resulting impurities may cause peeling
off the coating on some of the hardware, water channels blockage by
built-up residue, improper operation of the water pump, water tank tube
breakage, and o-rings deformation leading to leakage. Any issues related
to the use of inappropriate water-cooling liquid will be the responsibility of
the consumer.
[ 11 ]
記得上角要放對應的 LOGO!
[ 12 ]
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
使用說明書
出 進
DRGB LED
請接 1主版或 2 其他設備的 DRGB 插槽
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
12
主版
A
LG
L
INTE 1700
INTEL LGA 2066
1700
Bitspower Premium Summit M Silver Moon
Limited Edition (Compatible with 1700) V2
[ 13 ]
請按照正確的順序安裝
手轉螺絲
1 毫米墊片
冷頭
孔位固定螺絲
彈簧
安裝方式 1
[ 14 ]
手轉螺絲
彈簧
1 毫米墊片
1.2 毫米墊片
冷頭
手轉螺帽
請按照正確的順序安裝
背板墊片
3M 背膠絕緣片
金屬背板
M3x32 毫米螺絲
手轉螺絲不能鎖太緊，彈簧略有壓迫且保有間隙如下圖。手轉
螺絲不能旋轉到底，當鎖太緊時，SCM3F6 螺絲會被帶動，並
會被帶離主板，反而導致冷頭與 CPU 貼合效果不好。
安裝方式 2
[ 15 ]
96
90
48
54
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4
出 進
DRGB LED
請接 1主版或 2 其他設備的 DRGB 插槽
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
12
主版
[ 16 ]
手轉螺絲
彈簧
1 毫米墊片
1.2 毫米墊片
背板墊片
3M 背膠絕緣片
金屬背板
M3x32 毫米螺絲
冷頭
支架 (AM4)
手轉螺帽
請按照正確的順序安裝
手轉螺絲不能鎖太緊，彈簧略有壓迫且保有間隙如下圖。手轉
螺絲不能旋轉到底，當鎖太緊時，SCM3F6 螺絲會被帶動，並
會被帶離主板，反而導致冷頭與 CPU 貼合效果不好。
安裝方式 1
[ 17 ]
安裝方式 2
請按照正確的順序安裝
手轉螺絲
1 毫米墊片
冷頭
SC6-32M3 螺絲
主板
原廠背板
彈簧
[ 18 ]
105
46
AMD SOCKET TR4
AMD SOCKET TR4
65.2
X399
出 進
DRGB LED
請接 1主版或 2 其他設備的 DRGB 插槽
主版 DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
12
[ 19 ]
請按照正確的順序安裝
手轉螺絲
1 毫米墊片
冷頭
孔位固定螺絲
支架 (X399)
彈簧
安裝方式
[ 20 ]
組裝步驟
配件
4
12
3
墊片
背板 固定螺帽
背板螺絲
4 個
1 片 8 個
4 支
78MM 92.56MM
1.5MM
組裝步驟
步驟 1
1
2
3
適用於 LGA 1700 主板
BPTA-MKCPUMS-1700
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
