VENOM Atomik Miss Excite Hydro 24in Brushless RC Boat 取扱説明書

ページが読み込まれています...

Install 8 AA Batteries

Note: For more detailed instructions, please refer to the

VR3S instruction manual that came with your model.

The water-cooled Atomik™ 60A Pro Marine Brushless Speed Control that came in your Atomik™ Miss Excite

24” RTR Electric Boat is pre-programmed from the factory. If you need to re-program it, please follow the

instructions below.

Program the ESC

Use your transmitter to program the ESC in 4 easy steps:

1) Enter program mode.

2) Select programmable item.

3) Choose the new value of the selected time.

4) Exit

AA BATTERIES

NiMH 6 CELL STICK PACKS

1521 AA Rechargeable NiMH

ECOAA8AA ECO Alkaline Batteries

CHARGER

0657 Venom Pro Charger

1532 7.2V 6 cell 3000mAh NiMH Flat Pack

NiMH 7 and 8 CELL STICK PACKS

1532-7 8.4V 7 cell 3000mAh NiMH Hump Pack

1532-8 9.6V 8 cell 3000mAh NiMH Hump Pack

Curved Scissors

Needle Nosed Pliers

Side Cutters

LiPO BATTERY PACKS

RECOMMENDED BATTERY PACKS

1580 20C 4000mAh 11.1V LiPO

1581 20C 5400mAh 11.1V LiPO

15013 30C 3200mAh 14.8V LiPO

x8

For Radio

1.5mm

2.0mm

2.5mm

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Hobby Knife #11 Blade

Screwdriver

No.2

No.1

Nut Driver

5.5mm

Ruler straight Edge

Hex Driver

REQUIRED ITEMS

ESC SETUP

THE RADIO

Power Switch

Steering Trim

Steering Wheel

Steering EPA

Range Test

REV Switch

Fail Safe

Throttle EPA

ST. Dual Rate

Throttle Trim

Throttle Trigger

Battery Box

3

68

1. / 1.

2. 2.

3. 3.

1. 1.

2. 2.

3. 3.

4. 4.

1. / 1.

1. 1.

:

Atomik™ Atomik™ 90

30

Atomik™ 1-800-705-0620 (208-762-0620) E

[email protected]

Atomik™ ; Atomik™

Atomik™ 800-705-0620 (208-762-0620) E

[email protected]

Atomik™ Atomik™

()

(

)

FCC:

FCC ID: V6KCY300

:

: FCC 15B B

1 :

-

Atomik™( DVD)

[email protected]

Atomik™

()

CAUTION: LOW VOLTAGE CUT-OFF

Do not use “NO PROTECTION” when using LiPO battery packs. Monitor the battery pack temperatures after

each run. Do not allow the battery pack temperatures to exceed 120º F/ 52º C while in use. Select a higher low

voltage cut-off setting to help reduce the temperature of the battery packs. It is OK to use “NO PROTECTION”

when using NiCD or NiMH battery packs.

ESC SETUP CONT.

Tuning

Category

Running

Mode

LiPO

Cell #

Low

Voltage

Cut-off

Timing

Forward

Only

Auto

Calculate

No

Protection

0º

Forward &

Backward

2

Cells

2.8V/Cell

3.75º

3

Cells

3.0V/Cell

7.5º

4

Cells

3.2V/Cell

11.25º

5

Cells

3.4V/Cell

15º

6

Cells

18.75º 22.5º 26.25º

BEEP TONES

“B”

1 Short Beep

“BB”

2 Short Beeps

“BBB”

3 Short Beeps

“BBBB”

4 Short Beeps

“Beep-”

1 Long Beep

“Beep-B”

1 Long

1 Short Beep

“Beep-BB”

1 Long

2 Short Beeps

“Beep-BBB”

1 Long

3 Short Beeps

1

FULL THROTTLE

Entering Program Mode

Shaded Fields are Factory Settings (Recommended).

Selecting Category

Selecting Value for Category

If you are unsure if you have exited the program mode, you can disconnect

the battery and your programming will be saved.

2

FULL to NEUTRAL

3

FULL THROTTLE

Turn on transmitter.

Hold full throttle and connect battery.

- Continue to hold full throttle until musical tone sounds (5 seconds).

* CONTINUE TO HOLD FULL THROTTLE WHILE MOVING ON TO STEP 2*

Your ESC will again emit a series of beep tones. The beep tones represent a

dierent value. (Review chart below for tone diagram).

To select a value, simply wait for the desired beep tones to emit and pull full throttle.

Move the throttle to the neutral position. Within 2 seconds you will exit program mode. If you

continue to full throttle position, you will go back to step #2 and you can select a different tuning

category.

The ESC will emit a series of beep patterns. Each pattern represents a category:

To select tuning category, move throttle to neutral after desired beep pattern sounds.

*YOU ARE NOW IN THE SELECTED TUNING CATEGORY*

1. “Beep” Running Mode

2. “Beep-Beep” LiPO Cells

3. “Beep-Beep-Beep” Low Voltage Cutoff Threshold

4. “Beep-Beep-Beep-Beep” Timing

67

4

54

ATOMIK-RC.COM

ページが読み込まれています...

Slide the prop onto the drive shaft making sure to align the notch with the drive dog. Use the supplied lock nut to secure the

prop to the propshafts. Use caution when installing the prop as it may have extremely sharp edges.

INSTALLING THE PROPELLER

Always use a charger specifically rated to charge your batteries. Charging and discharging batteries has the potential

for serious injury to persons and damage to property. Caution: If batteries get hot during charging, discontinue charging

immediately and disconnect battery from charger. Never leave battery unattended while charging. If you are unsure of how

to charge this battery, please contact Atomik™ or seek the advice of your local hobby shop. Never let children charge

batteries without adult supervision.

BOAT STAND

BATTERY INSTALLATION

4

Finished Stand

Thin CA Glue

2

1

3

2

1.

2.

3. ()

4.

5.

6.

1.

2.

3.

4.

1.

2.

3.

4.

1.

2.

3.

4.

5.

1367 V500 Marine Outrunner for Miss Ex 2000Kv

1398 Atomik Pro Brushless Marina 60AMP ESC

1825 Atomik High Torque Metal Gear Servo

1883 Rubber push Rod Seals - SJXL/King/Segad

1885 Aluminum Antenna Holder (Blue) - SJXL/King/Segad

1886 Antenna Tube - SJXL/King/Segad

1926 Silicone Water Cooling Tubing - 50cm

1930 Hull/Hatch Set - ME

1931 Hatch - ME

1932 Motor Mount - ME

1933 Drive Shaft Housing - ME

1934 Drive Tube - ME

1935 Flex Shaft - ME

1936 Rudder - ME

1937 Rudder Strut - ME

1938 Control Rod - ME

1939 Boat Stand - ME

1940 Turn Fin - ME

1962 Shaft Coupler 5mm

1975 Servo Mount - EKOS/ ME

1979 Drive Dog - EKOS/P1 KOS/ ME

1980 Prop Spacer - EKOS/P1 KOS/ ME

1981 3 Blade Prop D32 P1.4 - EKOS/ ME

1985 Prop Nut - EKOS/ P1KOS/ ME

1987 Ball Bearing 4 x 7 - EKOS/P1 KOS/ ME

1988 Ball Bearing 4 x 7 Flanged - EKOS/P1 KOS/ ME

5

66

1. Thread the antenna from inside the hull up

through the base of the antenna tube holder.

2. Thre

ad the antenna through the antenna tube.

3. Seat the antenna into the antenna tube holder

and then cover the end with the rubber cap.

4.

For added security, you can use a small piece of

silicone tubing to hold the antenna in place.

1. Slide pin through pivot

block. Apply thread lock and

tighten the set screw.

2. Attach the rudder assembly

with both screws. Note that

the clear (break-away) screw

is used on the bottom hole.

3. Slide the control rod through

the pivot block. Center

servo, apply thread lock,

and tighten set screw.

INSTALLING THE ANTENNA

INSTALLING THE RUDDER

Thread Lock

3

1

2

3x3mm Set Screw

3mm Lock Nut

Needle Nosed Pliers

2.5mm

No.2

2.5mm

65

6

76

ATOMIK-RC.COM

ページが読み込まれています...

1 2

3

4

Secure the hatch by sliding the front pin into the hole at the front of the hull opening. The hatch should drop easily down

so that the magnets hold the hatch securely in place. To waterproof the hatch, use strips of clear tape to seal the lid on

all four sides.

BASIC CONTROLS

INSTALLING THE HATCH

Use the steering dual rate to adjust the steering sensitivity.

NOTE: To avoid flipping the boat, reduce the throttle to slow the boat while turning.

Refer to the radio manual that came with your kit for complete instructions.

WHEEL RIGHT WHEEL LEFT NEUTRAL THROTTLEWHEEL STRAIGHT

RUDDER RIGHT RUDDER LEFT FULL THROTTLERUDDER STRAIGHT

4mm

4mm187

( ) 0

2.5mm

/

(0)

1

2

__mm

2.5mm

: 71

7

64

1 2

3

4

:

2( )

Follow the same steps used to install the prop. If you are using a aftermarket prop, make sure it is sized for a 4mm prop

shaft. If you are not using a 4mm prop, you will need to shim the prop shaft or use an adapter to increase the diameter to

.187 inch.

The alignment of the propeller shaft is parallel to the bottom of

the hull (Keel) which is considered zero degrees (0 deg) and a

neutral setting. The thrust of the propeller is in line with the

center of the hull and has no effect on the hull ride angle.

Loosen the drive using a pair of needle nose pliers and a 2.5mm Hex Driver. Adjust the drive up or down to change the

running angle of the boat. Using a ruler, measure the distance from the top of the drive to the botom of the drive

mounting strut.

TUNING GUIDE

REPLACING/ UPGRADING THE PROP

ADJUST AND MEASURE THE DRIVE SHAFT

NEUTRAL THRUST ANGLE (0 DEGREES)

1

2

__mm

2.5mm

Hex Driver

Note: See page 15 to save your set up.

Bow Up

Neutral

Bow down

Bow Up

Neutral

Bow down

Needle Nosed Pliers

63

8

98

ATOMIK-RC.COM

ページが読み込まれています...

7

8

.

1.

2.

3.

4.

1.

2

( )

3.

3

1

2

3x3mm

3mm

2.5mm

No.2

2.5mm

9

62

4mm 4mm

187

AtomikTM(

)

4

2

1

3

2

BOAT MAINTENANCE

DRIVE LINE

1. Remove the prop.

2. Loosen the motor coupler set screws for the flex cable.

3. Slide the flex cable out of the drive.

4. Lubricate the flex cable with marine grease.

5. Lubricate the drive ball bearings with a light oil for bearings.

6. Reassemble the drive and wipe away any excess grease and oil.

HULL

1. The hull requires very little maintenance, but must be kept in good condition in order to perform as expected and to

ensure safe operation.

2. Look closely at the exterior surfaces of the hull.

3. Check for damage, chips, cracks and scratches.

4. Determine if damage has weakened the fiberglass and take the appropriate action to fix the

damage. Scratches and hair line cracks are common and typically do not require any attention.

HARDWARE

1. Radio control boats experience high frequency vibrations and as a result the screws, nuts and bolts will become

loose.

2. Check all the motor hardware and motor mounts.

3. Check all running gear, hardware, rudder, drive, steering linkage, water-cooling system, etc.

4. Use Thread Lock on all metal to metal hardware contacts.

WHAT TO DO AFTER THE BOAT HAS BEEN SUBMERGED

1. Remove the motor and lubricate the bearings on the motor.

2. Remove the electronics.

3. Dry out the interior.

4. The servo, receiver and battery pack will need to be dried out and checked for proper operation before they are

used again.

5. Test the battery pack under load to make sure it is ok to continue regular use.

PARTS LIST

1367 V500 Marine Outrunner for Miss Ex 2000Kv

1398 Atomik Pro Brushless Marina 60AMP ESC

1825 Atomik High Torque Metal Gear Servo

1883 Rubber Push Rod Seals - SJXL/King/Segad

1885 Aluminum Antenna Holder (Blue) - SJXL/King/Segad

1886 Antenna Tube - SJXL/King/Segad

1926 Silicone Water-Cooling Tubing - 50cm

1930 Hull/Hatch Set - ME

1931 Hatch - ME

1932 Motor Mount - ME

1933 Drive Shaft Housing - ME

1934 Drive Tube - ME

1935 Flex Shaft - ME

1936 Rudder - ME

1937 Rudder Strut - ME

1938 Control Rod - ME

1939 Boat Stand - ME

1940 Turn Fin - ME

1962 Shaft Coupler 5mm

1975 Servo Mount - EKOS/ ME

1979 Drive Dog - EKOS/P1 KOS/ ME

1980 Prop Spacer - EKOS/P1 KOS/ ME

1981 3 Blade Prop D32 P1.4 - EKOS/ ME

1985 Prop Nut - EKOS/ P1KOS/ ME

1987 Ball Bearing 4 x 7 - EKOS/P1 KOS/ ME

1988 Ball Bearing 4 x 7 Flanged - EKOS/P1 KOS/ ME

Use high quality Marine

Grease to lubricate the flex

cable.

Motor Coupler Set ScrewMotor Coupler Set Screw

Lubricate the drive bearings

with a light bearing oil.

61

10

1110

ATOMIK-RC.COM

ページが読み込まれています...

Atomik™ 24” RTR

Atomik™ P1 35” RTR

Atomik™ 24” RTR

R/C

1

Atomik™ 24” RTR

( )

Atomik™ 24” RTR

58

59

60

( ) 60

ESC 60-61

62

63

64

65-66

66

67

68

65 68

FCC 68

69-71

SETUP NOTES

BATTERY

BOAT WEIGHT AND SETUP SPECS

13

58

• (PFD)

•

ESC

•

AtomikTM

( )

•

‘atomik’

•

• 18

:22 /559mm

:24 /610mm

:10.75 /273mm

:4.43 /112.5mm

: 3.3 /1.49kg

:20

60A

:60A

(10S): 120A

BEC :

BEC:6V/3A

: (LiPO): 2-6 (NiMH):

6-18

:93g

:5mm

( ):94x33x18mm

:VR3S 3Ch 2.4GHz

:230 x 175 x 75mm (hxwxd)

:1.4 /566 (w )

:Atomik 3Ch (8188)

:

:17/60°

:107 / (7.0kg.cm)/ 6

:

MOTOR & ESC

SERVO

PROP & DRIVE ANGLES

CG RANGE 165-185mm

mm

57

14

1514

ATOMIK-RC.COM

Atomik™ 24” RTR

Atomik™ P1 35” RTR

Atomik™ 24” RTR

R/C

1

Atomik™ 24” RTR

( )

Atomik™ 24” RTR

58

59

60

( ) 60

ESC 60-61

62

63

64

65-66

66

67

68

65 68

FCC 68

69-71

SETUP NOTES

BATTERY

BOAT WEIGHT AND SETUP SPECS

13

58

• (PFD)

•

ESC

•

AtomikTM

( )

•

‘atomik’

•

• 18

:22 /559mm

:24 /610mm

:10.75 /273mm

:4.43 /112.5mm

: 3.3 /1.49kg

:20

60A

:60A

(10S): 120A

BEC :

BEC:6V/3A

: (LiPO): 2-6 (NiMH):

6-18

:93g

:5mm

( ):94x33x18mm

:VR3S 3Ch 2.4GHz

:230 x 175 x 75mm (hxwxd)

:1.4 /566 (w )

:Atomik 3Ch (8188)

:

:17/60°

:107 / (7.0kg.cm)/ 6

:

MOTOR & ESC

SERVO

PROP & DRIVE ANGLES

CG RANGE 165-185mm

mm

57

14

15

ATOMIK-RC.COM

18003

14

ページが読み込まれています...

• (PFD)

•

ESC

•

AtomikTM

( )

•

‘atomik’

•

• 18

:22 /559mm

:24 /610mm

:10.75 /273mm

:4.43 /112.5mm

: 3.3 /1.49kg

:20

60A

:60A

(10S): 120A

BEC :

BEC:6V/3A

: (LiPO): 2-6 (NiMH):

6-18

:93g

:5mm

( ):94x33x18mm

:VR3S 3Ch 2.4GHz

:230 x 175 x 75mm (hxwxd)

:1.4 /566 (w )

:Atomik 3Ch (8188)

:

:17/60°

:107 / (7.0kg.cm)/ 6

:

MOTOR & ESC

SERVO

PROP & DRIVE ANGLES

CG RANGE 165-185mm

mm

57

14

Atomik™ 24” RTR

Atomik™ P1 35” RTR

Atomik™ 24” RTR

R/C

1

Atomik™ 24” RTR

( )

Atomik™ 24” RTR

58

59

60

( ) 60

ESC 60-61

62

63

64

65-66

66

67

68

65 68

FCC 68

69-71

SETUP NOTES

BATTERY

BOAT WEIGHT AND SETUP SPECS

13

58

5958

ATOMIK-RC.COM

Atomik™ 24” RTR

Atomik™ P1 35” RTR

Atomik™ 24” RTR

R/C

1

Atomik™ 24” RTR

( )

Atomik™ 24” RTR

58

59

60

( ) 60

ESC 60-61

62

63

64

65-66

66

67

68

65 68

FCC 68

69-71

SETUP NOTES

BATTERY

BOAT WEIGHT AND SETUP SPECS

13

58

59

ATOMIK-RC.COM

18003

58

ページが読み込まれています...

Problem Cause Fix

Speed Control does not operate. 1. Transmitter and/or receiver is not switched on. 1. Switch on.

2. Batteries are not fully charged. 2. Charge batteries.

3. Improper radio installation. 3. Reinstall correctly.

Motor does not operate. 1. Batteries are not fully charged. 1. Charge batteries.

2. Improper radio installation. 2. Reinstall correctly.

3. Loose motor wire connection. 3. Check connections.

4. Damaged motor. 4. Replace or Repair.

1. Flex shaft and/or bearings are dirty. 1. Clean and Regrease.

Motor rotates, but boat does not move.

Propellers do not rotate freely when

disconnected from the motors.

1. Motor coupler set screw is loose. 1. Tighten set screw.

TROUBLE SHOOTING

WARNINGS / WARRANTY

FCC Warning:

FCC ID: V6KCY300

CAUTION: Atomik™ is not responsible for any radio or TV interference caused by unauthorized modications to this product. Changes or modications not

authorized by Atomik™ will void all warranties.

NOTE: This product has been tested and found to comply with the limits for a Class B digital device, compliant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency

energy and, if not installed and used as instructed, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the

product on and o, correct the interference by trying one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from the receiver.

- Consult the dealer or an experienced radio/TV technician for help.

This product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Be responsible, dispose of properly.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Charging and discharging batteries has the potential for serious injury to persons and damage to property. In purchasing this product, the user agrees to accept

responsibility for all such risks, and will not hold Atomik™, it’s aliates, manufacturers, distributors, or retail partners responsible for any accident, injury to

persons, or damage to property resulting from the use of this product.

Adult supervision is required when using this product. This product should be assembled by an adult before use. Proper assembly should be checked by an adult

before use. This product should be periodically examined by an adult for potential hazards. Any potential hazardous parts should be repaired or replaced.

WARNING:

This product may contain sharp edges or objects that can cause cuts or other bodily injury. To prevent cuts or other bodily injury, do not contact sharp edges or objects.

Important Notice

Atomik™ assumes sole responsibility for our products; therefore, dealers should not be involved in any warranty issues. All warranty claims are to be directed

to Atomik™ Customer Service. Before returning any defective product, please contact Atomik™ Customer Service at 800-705-0620 (208-762-0620) or

[email protected]om to receive a Return Merchandise Authorization Number. A dated & itemized sales receipt must accompany any product

returned for warranty work.

General Warranty Policies

Atomik™ warrants this product to be free of material and workmanship defects when new. Atomik™ will at its sole discretion repair or replace defective

components free of charge within 90 days from date of purchase or within 30 days for all electronic components.* This warranty does not cover wear and tear,

crash damage, modications, failure to perform routine maintenance, or any damages arising as a result of improper use. All warranty claims are to be directed

to Atomik™ Customer Service at 1-800-705-0620 (208-762-0620) or customerservice@atomik-rc.com.

GUARANTEE

All products are inspected and adjusted individually before leaving the manufacturer and are guaranteed to be free of material defects and manufacturing faults.

Actual product may vary from product shown. Product is subject to change.

Notice of Rights

otherwise, without the prior written permission of Atomik™. For information on getting permission for reprints and excerpts, contact

[email protected]om.

Notice of Liability

The information in this manual is distributed on an “As Is” basis, without warranty. While every precaution has been taken in the preparation of the manual, Atomik™

does not have any liability to any person or entity with respect to any loss or damage caused or alleged to be caused directly or indirectly by the information

contained in this manual or by the products described in it.

Release of Liability

Atomik™, It’s aliates, manufacturers, distributors, or retail partners shall not be held liable for any accident, injury to persons, or damage to property resulting

from use, misuse, or abuse of any Atomik™ product. In purchasing a Atomik™ product the user agrees to accept responsibility for all such risks.

#1

ESC 2 ‘’

5

#2

‘ ’

3

1. ‘’

2. ‘’

3. ‘’

4. ‘’

#3

ESC

: 2

2

4

2 :

1:

3 2

2:

ESC

:

‘ ’

120o F/ 52o C

‘ ’ OK

ESC

Lipo

#

0º

2

2.8V/

3.75º

3

3.0V/

7.5º

4

3.2V/

11.25º

5

3.4V/

15º

6

18.75º 22.5º 26.25º

“B”

1

“BB”

2

“BBB”

3

“BBBB”

4

“-”

1

“-B”

1

“-BB”

1

2

“-BBB”

1

3

11

60

1

2

3

61

ATOMIK-RC.COM

18003

60

4mm 4mm

187

AtomikTM(

)

4

2

1

3

2

BOAT MAINTENANCE

DRIVE LINE

1. Remove the prop.

2. Loosen the motor coupler set screws for the flex cable.

3. Slide the flex cable out of the drive.

4. Lubricate the flex cable with marine grease.

5. Lubricate the drive ball bearings with a light oil for bearings.

6. Reassemble the drive and wipe away any excess grease and oil.

HULL

1. The hull requires very little maintenance, but must be kept in good condition in order to perform as expected and to

ensure safe operation.

2. Look closely at the exterior surfaces of the hull.

3. Check for damage, chips, cracks and scratches.

4. Determine if damage has weakened the fiberglass and take the appropriate action to fix the

damage. Scratches and hair line cracks are common and typically do not require any attention.

HARDWARE

1. Radio control boats experience high frequency vibrations and as a result the screws, nuts and bolts will become

loose.

2. Check all the motor hardware and motor mounts.

3. Check all running gear, hardware, rudder, drive, steering linkage, water-cooling system, etc.

4. Use Thread Lock on all metal to metal hardware contacts.

WHAT TO DO AFTER THE BOAT HAS BEEN SUBMERGED

1. Remove the motor and lubricate the bearings on the motor.

2. Remove the electronics.

3. Dry out the interior.

4. The servo, receiver and battery pack will need to be dried out and checked for proper operation before they are

used again.

5. Test the battery pack under load to make sure it is ok to continue regular use.

PARTS LIST

1367 V500 Marine Outrunner for Miss Ex 2000Kv

1398 Atomik Pro Brushless Marina 60AMP ESC

1825 Atomik High Torque Metal Gear Servo

1883 Rubber Push Rod Seals - SJXL/King/Segad

1885 Aluminum Antenna Holder (Blue) - SJXL/King/Segad

1886 Antenna Tube - SJXL/King/Segad

1926 Silicone Water-Cooling Tubing - 50cm

1930 Hull/Hatch Set - ME

1931 Hatch - ME

1932 Motor Mount - ME

1933 Drive Shaft Housing - ME

1934 Drive Tube - ME

1935 Flex Shaft - ME

1936 Rudder - ME

1937 Rudder Strut - ME

1938 Control Rod - ME

1939 Boat Stand - ME

1940 Turn Fin - ME

1962 Shaft Coupler 5mm

1975 Servo Mount - EKOS/ ME

1979 Drive Dog - EKOS/P1 KOS/ ME

1980 Prop Spacer - EKOS/P1 KOS/ ME

1981 3 Blade Prop D32 P1.4 - EKOS/ ME

1985 Prop Nut - EKOS/ P1KOS/ ME

1987 Ball Bearing 4 x 7 - EKOS/P1 KOS/ ME

1988 Ball Bearing 4 x 7 Flanged - EKOS/P1 KOS/ ME

Use high quality Marine

Grease to lubricate the flex

cable.

Motor Coupler Set ScrewMotor Coupler Set Screw

Lubricate the drive bearings

with a light bearing oil.

61

10

7

8

.

1.

2.

3.

4.

1.

2

( )

3.

3

1

2

3x3mm

3mm

2.5mm

No.2

2.5mm

9

62

6362

ATOMIK-RC.COM

7

8

.

1.

2.

3.

4.

1.

2

( )

3.

3

1

2

3x3mm

3mm

2.5mm

No.2

2.5mm

9

62

63

ATOMIK-RC.COM

18003

62

1 2

3

4

:

2( )

Follow the same steps used to install the prop. If you are using a aftermarket prop, make sure it is sized for a 4mm prop

shaft. If you are not using a 4mm prop, you will need to shim the prop shaft or use an adapter to increase the diameter to

.187 inch.

The alignment of the propeller shaft is parallel to the bottom of

the hull (Keel) which is considered zero degrees (0 deg) and a

neutral setting. The thrust of the propeller is in line with the

center of the hull and has no effect on the hull ride angle.

Loosen the drive using a pair of needle nose pliers and a 2.5mm Hex Driver. Adjust the drive up or down to change the

running angle of the boat. Using a ruler, measure the distance from the top of the drive to the botom of the drive

mounting strut.

TUNING GUIDE

REPLACING/ UPGRADING THE PROP

ADJUST AND MEASURE THE DRIVE SHAFT

NEUTRAL THRUST ANGLE (0 DEGREES)

1

2

__mm

2.5mm

Hex Driver

Note: See page 15 to save your set up.

Bow Up

Neutral

Bow down

Bow Up

Neutral

Bow down

Needle Nosed Pliers

63

8

1 2

3

4

Secure the hatch by sliding the front pin into the hole at the front of the hull opening. The hatch should drop easily down

so that the magnets hold the hatch securely in place. To waterproof the hatch, use strips of clear tape to seal the lid on

all four sides.

BASIC CONTROLS

INSTALLING THE HATCH

Use the steering dual rate to adjust the steering sensitivity.

NOTE: To avoid flipping the boat, reduce the throttle to slow the boat while turning.

Refer to the radio manual that came with your kit for complete instructions.

WHEEL RIGHT WHEEL LEFT NEUTRAL THROTTLEWHEEL STRAIGHT

RUDDER RIGHT RUDDER LEFT FULL THROTTLERUDDER STRAIGHT

4mm

4mm187

( ) 0

2.5mm

/

(0)

1

2

__mm

2.5mm

: 71

7

64

6564

ATOMIK-RC.COM

1 2

3

4

Secure the hatch by sliding the front pin into the hole at the front of the hull opening. The hatch should drop easily down

so that the magnets hold the hatch securely in place. To waterproof the hatch, use strips of clear tape to seal the lid on

all four sides.

BASIC CONTROLS

INSTALLING THE HATCH

Use the steering dual rate to adjust the steering sensitivity.

NOTE: To avoid flipping the boat, reduce the throttle to slow the boat while turning.

Refer to the radio manual that came with your kit for complete instructions.

WHEEL RIGHT WHEEL LEFT NEUTRAL THROTTLEWHEEL STRAIGHT

RUDDER RIGHT RUDDER LEFT FULL THROTTLERUDDER STRAIGHT

4mm

4mm187

( ) 0

2.5mm

/

(0)

1

2

__mm

2.5mm

: 71

7

64

65

ATOMIK-RC.COM

18003

64

1. Thread the antenna from inside the hull up

through the base of the antenna tube holder.

2. Thre

ad the antenna through the antenna tube.

3. Seat the antenna into the antenna tube holder

and then cover the end with the rubber cap.

4.

For added security, you can use a small piece of

silicone tubing to hold the antenna in place.

1. Slide pin through pivot

block. Apply thread lock and

tighten the set screw.

2. Attach the rudder assembly

with both screws. Note that

the clear (break-away) screw

is used on the bottom hole.

3. Slide the control rod through

the pivot block. Center

servo, apply thread lock,

and tighten set screw.

INSTALLING THE ANTENNA

INSTALLING THE RUDDER

Thread Lock

3

1

2

3x3mm Set Screw

3mm Lock Nut

Needle Nosed Pliers

2.5mm

No.2

2.5mm

65

6

Slide the prop onto the drive shaft making sure to align the notch with the drive dog. Use the supplied lock nut to secure the

prop to the propshafts. Use caution when installing the prop as it may have extremely sharp edges.

INSTALLING THE PROPELLER

Always use a charger specifically rated to charge your batteries. Charging and discharging batteries has the potential

for serious injury to persons and damage to property. Caution: If batteries get hot during charging, discontinue charging

immediately and disconnect battery from charger. Never leave battery unattended while charging. If you are unsure of how

to charge this battery, please contact Atomik™ or seek the advice of your local hobby shop. Never let children charge

batteries without adult supervision.

BOAT STAND

BATTERY INSTALLATION

4

Finished Stand

Thin CA Glue

2

1

3

2

1.

2.

3. ()

4.

5.

6.

1.

2.

3.

4.

1.

2.

3.

4.

1.

2.

3.

4.

5.

1367 V500 Marine Outrunner for Miss Ex 2000Kv

1398 Atomik Pro Brushless Marina 60AMP ESC

1825 Atomik High Torque Metal Gear Servo

1883 Rubber push Rod Seals - SJXL/King/Segad

1885 Aluminum Antenna Holder (Blue) - SJXL/King/Segad

1886 Antenna Tube - SJXL/King/Segad

1926 Silicone Water Cooling Tubing - 50cm

1930 Hull/Hatch Set - ME

1931 Hatch - ME

1932 Motor Mount - ME

1933 Drive Shaft Housing - ME

1934 Drive Tube - ME

1935 Flex Shaft - ME

1936 Rudder - ME

1937 Rudder Strut - ME

1938 Control Rod - ME

1939 Boat Stand - ME

1940 Turn Fin - ME

1962 Shaft Coupler 5mm

1975 Servo Mount - EKOS/ ME

1979 Drive Dog - EKOS/P1 KOS/ ME

1980 Prop Spacer - EKOS/P1 KOS/ ME

1981 3 Blade Prop D32 P1.4 - EKOS/ ME

1985 Prop Nut - EKOS/ P1KOS/ ME

1987 Ball Bearing 4 x 7 - EKOS/P1 KOS/ ME

1988 Ball Bearing 4 x 7 Flanged - EKOS/P1 KOS/ ME

5

66

6766

ATOMIK-RC.COM

Slide the prop onto the drive shaft making sure to align the notch with the drive dog. Use the supplied lock nut to secure the

prop to the propshafts. Use caution when installing the prop as it may have extremely sharp edges.

INSTALLING THE PROPELLER

Always use a charger specifically rated to charge your batteries. Charging and discharging batteries has the potential

for serious injury to persons and damage to property. Caution: If batteries get hot during charging, discontinue charging

immediately and disconnect battery from charger. Never leave battery unattended while charging. If you are unsure of how

to charge this battery, please contact Atomik™ or seek the advice of your local hobby shop. Never let children charge

batteries without adult supervision.

BOAT STAND

BATTERY INSTALLATION

4

Finished Stand

Thin CA Glue

2

1

3

2

1.

2.

3. ()

4.

5.

6.

1.

2.

3.

4.

1.

2.

3.

4.

1.

2.

3.

4.

5.

1367 V500 Marine Outrunner for Miss Ex 2000Kv

1398 Atomik Pro Brushless Marina 60AMP ESC

1825 Atomik High Torque Metal Gear Servo

1883 Rubber push Rod Seals - SJXL/King/Segad

1885 Aluminum Antenna Holder (Blue) - SJXL/King/Segad

1886 Antenna Tube - SJXL/King/Segad

1926 Silicone Water Cooling Tubing - 50cm

1930 Hull/Hatch Set - ME

1931 Hatch - ME

1932 Motor Mount - ME

1933 Drive Shaft Housing - ME

1934 Drive Tube - ME

1935 Flex Shaft - ME

1936 Rudder - ME

1937 Rudder Strut - ME

1938 Control Rod - ME

1939 Boat Stand - ME

1940 Turn Fin - ME

1962 Shaft Coupler 5mm

1975 Servo Mount - EKOS/ ME

1979 Drive Dog - EKOS/P1 KOS/ ME

1980 Prop Spacer - EKOS/P1 KOS/ ME

1981 3 Blade Prop D32 P1.4 - EKOS/ ME

1985 Prop Nut - EKOS/ P1KOS/ ME

1987 Ball Bearing 4 x 7 - EKOS/P1 KOS/ ME

1988 Ball Bearing 4 x 7 Flanged - EKOS/P1 KOS/ ME

5

66

67

ATOMIK-RC.COM

18003

66

1. / 1.

2. 2.

3. 3.

1. 1.

2. 2.

3. 3.

4. 4.

1. / 1.

1. 1.

:

Atomik™ Atomik™ 90

30

Atomik™ 1-800-705-0620 (208-762-0620) E

[email protected]

Atomik™ ; Atomik™

Atomik™ 800-705-0620 (208-762-0620) E

[email protected]

Atomik™ Atomik™

()

(

)

FCC:

FCC ID: V6KCY300

:

: FCC 15B B

1 :

-

Atomik™( DVD)

[email protected]

Atomik™

()

CAUTION: LOW VOLTAGE CUT-OFF

Do not use “NO PROTECTION” when using LiPO battery packs. Monitor the battery pack temperatures after

each run. Do not allow the battery pack temperatures to exceed 120º F/ 52º C while in use. Select a higher low

voltage cut-off setting to help reduce the temperature of the battery packs. It is OK to use “NO PROTECTION”

when using NiCD or NiMH battery packs.

ESC SETUP CONT.

Tuning

VENOM Atomik Miss Excite Hydro 24in Brushless RC Boat 取扱説明書

このマニュアルも適しています

VENOM Atomik Miss Excite Hydro 24in Brushless RC Boat 取扱説明書

他の言語で

関連論文

その他のドキュメント