*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No. 31265
/ SAFETY PRECAUTIONS
/ ITEMS REQUIRED FOR OPERATION
/ PREPARE RADIO TRANSMISSION
/ BEFORE YOU BEGIN
/ ARRANGEMENT OF PLASTIC PARTS ON RUNNERS
/ ASSEMBLY
/ EXPLODED VIEW
/ SPARE PARTS & OPTIONAL PARTS
2 ~ 5
6 ~ 7
7
8 ~ 9
10 ~ 11
12 ~ 39
40 ~ 41
42 ~ 48
INDEX
UNDER SAFETY PRECAUTIONS
This radio control model is not a toy.
Copyright 2011 KYOSHO CORPORATION /
31265-T02
Before beginning assembly, please read these instructions thoroughly!
THE FINEST RADIO CONTROL MODELS
R
It's highly recommended that first-time enthusiasts seek the advice of an
experienced modeler before operating this vehicle.
Keep out of the reach of children!
Observe all safety precautions when operating this model. You are
responsible for this vehicle's proper maintenance and safe operation.
Always keep this instruction manual for quick reference.
Taking out liability insurance is recommended.
INSTRUCTION MANUAL
1:10 Scale Radio Controlled .12-.15 Engine Powered 4WD Touring Car Series
PureTen GP
V-ONE R4
In order to operate the model safely, adhere to following instructions:
*Here are some possibilities of significant damage to life and/or body, if the following explanations are not adhered to:
This product is a fully functional radio control model. It is not a toy!
To enjoy this model to its fullest, complete assembly properly, perform maintenance and add optional upgrades as desired.
Improper usage of Alkaline cells or rechargeable batteries may damage the electronics of the car and/or the radio.
This R/C car is designed for advanced users and competitive racing. A degree of skill is required for the assembly and
operation of this model and any damage to the model either during assembly or operation is the at the user’s risk and
responsibility. Also, depending on the engine (sold separately) used, the car can run at extremely high speeds. Only
run this model at a designated R/C track or circuit.
Never reverse connection nor disassemble batteries.
It may lead to damage and leakage.
Before you begin, read the manual thoroughly. First time builders should
seek advice from modelers who have experience in assembling models.
Warning !
PROHIBITED
SAFETY PRECAUTIONS
WARNING!
PROHIBITED
: This symbol indicates where caution is essential to avoid injury to yourself or others.
: This symbol points out actions that you should NOT do to avoid possible damage
or accidents.
Please read carefully before assembling and operating your model.
< Caution >
2
NO !
D/R
BATT.
ST.REV
TH.REV
N
N
R
R
POWER
This product includes many small, sharp objects, so it should be kept out
of the reach of children.
Always check the radio batteries!
With weak dry batteries, transmission and reception of the radio fall off.
Models may become out of control under such condition, which may
cause serious accidents.
Operate your model ONLY on designated areas, race tracks and other spacious areas. Do NOT operate it:
1. in residential districts and parks!
2. indoors and in limited space!
* Non-observance of the above may be cause for personal injuries and property damages.
When the model is behaving strangely . .!
Immediately stop the model and check the reason. Do not operate the
model until the problem is solved. This may lead to further trouble and
unforeseen accidents!
PROHIBITED
PROHIBITED
PROHIBITED
PROHIBITED
PROHIBITED
Do not operate in crowded places, near children or pets, or on public
streets - it may cause serious injury.
3
All tools require careful handling to avoid injury.
Painting must be done only in a well-ventilated area.
*The following are examples of situations that should be avoided for safe assembly, maintenance and operation:
Cautions !
PROHIBITED
Do not put fingers or any objects inside rotating and moving parts!
Right after use, do not touch the engine and muffler! Danger of burning
yourself!
PROHIBITED
PROHIBITED
*In order to avoid accidents and personal injury, be sure to observe the following:
Warning !
Handling fuel safely:
1. Handle fuel only outdoors!
2. Only use glow fuel for radio control models!
3. Never use fuel indoors or in places with open fires and sources of heat!
4. Never swallow fuel or let it into your eyes!
5. Store fuel only in cool, dry and dark places out of children's reach!
Tightly shut the cap!
6. Do not dispose of empty fuel cans into a fire!
There is danger of explosion!
PROHIBITED
1.
2.
3.
4.
5.
6.
4
Do not point the antenna towards another person. Do not store this model in hot or humid conditions, or in direct sunlight.
Always run your car with the body shell mounted!
Do not run your car on ground:
• that is overgrown with grass.
• that is muddy, sandy or rocky.
Check all screws, nuts etc. on a regular basis for looseness.
Do NOT install any option parts not made by Kyosho for this model.
To avoid causing irreparable damage, do NOT attempt any modifications.
PROHIBITEDPROHIBITED
PROHIBITED
PROHIBITED
Be sure that you're operating on a unique frequency from any other RC
vehicles in the area. Failure to do so will cause a loss of control and may
cause injury.
Always switch off the receiver and transmitter, then disconnect/remove
the batteries when the model is not in use. Failure to do so may cause
damage to the batteries from excessive discharge and leaking.
PROHIBITED
OFF
5
AAAA
AA
AA
Glow Engine
Fuel
1
Radio transmitter with at least 2
channels for 2 servos.
Stick-type
2ch radio set.
ITEMS REQUIRED FOR OPERATION (1)
This model requires a 2-channel, 2-servo R/C system
with reverse switch and servo trim functionality.
If reverse switch on the transmitter is to be used, refer
to the instruction manual included with the R/C model.
BEC connector switch is required. If your switch is not BEC
connector specification, please change it to BEC connector switch.
This kit is a competition-level model. Please install
with suitable high-performance servos.
2
Engine & Muffler
3
Items required for starting the engine.
4
Paint
No.96423
No.80164 No.ORI10325
5
Other required equipments
Use only: straight pack
Using same brand battery as your R/C system is recommended.
(max. dimensions 33x84x17mm)
KYOSHO SPRAY COLOR
No.7600176062
x2
Wheel-type
2ch radio set.
AA-size Batteries (For Transmitter)
Servo
Glow Fuel
Air Filter Tape
Tire setter Body
GP touring car sponge tires
(zero offset) for front & rear
Engine for .12
class cars
Plug
ManifoldMuffler
Joining Pipe
Fuel Pump
Plug Wrench Battery
Receiver
Switch
< Futaba >
BLS 351, 352, 451, 452
< KO >
PDS2345ICS, PDS2386ICS
PDS2367ICS, PDS2368ICS
< SANWA >
SRG-BR, CR, BZ, CZ
HVS-ZS, ZV
ERG-WX, WG, WZ
Battery
ORION Sport Power 2200
(Ni-MH Battery)
Cross Wrench
(5.5 / 7 / 8 / 10mm)
(Nitro 16~20%) Fuel Bottle 500cc
No.36216SNo.36217
Plug Heater
Spark Booster 2.0Booster Charger 2.0
No.36209
Starter
Multi Starter Box 2.0
No.36304
K.R.F Multi Tire Setter
No.36214 No.36214-02
K.R.F Automatic Tire Setter Adaptor (for Tire Setter)
(width 200mm)
This kit requires a .12 class engine.
For painting the body, use Kyosho
paints for models!
*Only SG Shaft (Pilot Shaft) with Slide
Carburetor engine without pull starter
Rear Exhaust is available.
No.36220
Suitable servos & receiver
6
SCREW
CEMENT
Special Glue
ON
OFF
Grease
Set up the radio as explained below.
CAUTION: Handle tools carefully!
KYOSHO Special Glue
No.96154
Instant Glue
5mm
No need to pre-drill! Drills neat 1 ~ 15mm holes directly!
SP KNIFE EDGE REAMER
No.36219
Clutch Spring Adjust Tool
No.80160
Can be used as plug wrench.
5
Tools required
Phillips screwdriver (sizes: S)
Hex screwdrivers
(1.5mm, 2mm, 2.5mm)
Needle Nose Pliers
Hex wrenche
(5mm)
Cross Wrench (small)
Wire Cutters
Scissors
Calipers
Water Pump Pliers
Rubber Cement
Box Wrench
Sharp Hobby Knife
Screw Cement
TOOLS INCLUDED Tools ACCESSORIES
4
3
6
ON
OFF
10
6
ON
OFF
10
Receiver
Switch
Battery
Transmitter
1
2
1
11
2
11
5
5
8
8
Transmitter
Servo
Servo
Antenna
1
2
3
4
5
6
7
8
9
10
11
Insert AA-size batteries into the Transmitter.
Extend the antenna of transmitter.
Connect the charged battery to the receiver.
Unwind the Receiver antenna.
Set trims of transmitter to center.
Switch "ON" the Transmitter.
Switch "ON" the Receiver.
Check that the servos move in accordance with the control
from transmitter.
Switch "OFF" the Receiver.
Switch "OFF" the Transmitter.
Retract the Transmitter antenna.
PREPARE RADIO TRANSMISSION
7
ON
OFF
9
ITEMS REQUIRED FOR OPERATION (2)
Grease
Loctite (Medium Strength / 10cc)
No.96178
5mm
1 ~ 15mm
KYOSHO
1
2
3
4
5
6
7
8
9
10
11
3
/
7
BEFORE YOU BEGIN (1)
1
First, read this instruction manual and familiarise yourself with the model’s
construction.
Check the kit contents. Should any parts be missing, contact the retail shop from
whom the model was purchased.
Compare nuts, bolts, screws, etc to the "Actual Size" drawings on each page
before fitting to ensure that you are installing the correct parts.
Tighten Self tapping (TP) screws into parts until you have a secure attachment.
However, be careful not to overly tighten TP screws as the threads may be
damaged.
SCREWS
3x12mm
F/H Screw
OTHER HARDWARE
3x12mm
Screw
3mm
12mm
3mm
12mm
Button Hex Screw
Cap Screw Set Screw
F/H Hex Screw
3mm
Washer
•
Nut
3mm
5x10mm
Metal Bushing
•
Ball Bearing
5mm
10mm
4mm
E4
E-ring
5.8mm
Pillow Ball
5.8mm
This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the
true-to-scale diagrams on the left side in each assembly step. Some screws are extras.
2
Before assembling, please read the following carefully:
TP
8
Symbols used throughout the instruction manual, comprise:
4
x2
2mm
BRG001
Apply epoxy glue.Drill holes with the
specified diameter.
Part bags used.
Ball bearings are optional !
(with optional part no.)
4
4
How to read the instruction manual:
3
A: Gives the name of the part being made and the serial number of steps for
assembling.
B: Details the key-number of parts, actual-size drawings and quantity of parts to use.
C: All parts, except screws, are identified by key Numbers. When purchasing spare
parts, identify the key number of the part required and cross reference this to the
Spare Parts page, which shows the purchasable spare parts and the key
numbers contained within.
D: This instruction manual uses several symbols. Pay careful attention to them
during construction.
Apply instant glue
(CA glue, super glue).
Apply grease.
Apply threadlocker
(screw cement).
Note the direction
Assemble as many
times as specified.
Assemble left and right
sides the same way.
True-to-scale diagram.
For Left.
For Right.
Temporarily tighten.
Cut off excess.
Ensure smooth, non-binding
movement when assembling.
Pay close attention here!
Assemble in the
specified order.
Apply rubber type glue.
Must be purchased
separately!
BEFORE YOU BEGIN (2)
Cut off shaded portion.
1
No.1
1
Front Suspension
5
King Pin
4 5 x 10mm
Metal Bushing
6
5
7
5
A
C
D
B
C
A:
B:
C: No.
No.
D:
9
V-ONE R4
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS
Shaded Parts are not used.
39
36
41
32 33
15
19
21
18
17
16
20
60
59
61
56 57
62
26
30
31
29
27
28
No.2
10
V-ONE R4
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS
Shaded Parts are not used.
52
55
47
22 25
20
23
49 46 48
51 50
53
54
No.5
No.7
74
73
65
66 67
63
64
69 68
75
72
70
71
No.3
Futaba
40
34 43
43
42 38
38
44
37
35
No.4
11
1
No.1
1
Differential
105
4x4mm
E7
E7
E7
< >23T Pulley
6
9
2
3
1
1
4 x 4mm
Set Screw
E7
E-ring
1
2
No.1
2
Differential
116
4x4mm
< >Brake Pulley
10
2
1
1
4 x 4mm
Set Screw
E7
E-ring
1
3
No.1
3
Differential
105
4x4mm
< >18T Pulley
8
5
2
3
1
1
4 x 4mm
Set Screw
E7
E-ring
1
x2
< >
< >
< >
12
V-ONE R4
4
No.1
4
Differential
128
200
13
11
158
128
200
183
183
90
90
89
89
14
91
91
5x12mm
5x12mm
2.6x6mm
2.6x6mm
< >Rear Differential
2
2
3
3
4
4
5
5
1
1
200
157
4
200
183
183
90
90
92
92
89
89
12
91
91
5x12mm
5x12mm
2.6x6mm
2.6x6mm
2x6mm
2x6mm
2
2
3
3
4
4
5
5
1
1
Pour Silicone Oil (#50000)
included in the kit.
219
Silicone Oil (#50000)
Fill up to 80%.
4
2.6 x 6mm
F/H Hex Screw
2
200
O-ring P4.5
2
5 x 12mm
Shim
5
No.1
5
Differential
< >Front Differential
Pour Silicone Oil (#300000)
included in the kit.
Silicone Oil (#300000)
Fill up to 80%.
4
2.6 x 6mm
F/H Hex Screw
2
200
O-ring P4.5
2
5 x 12mm
Shim
2 x 6mm
F/H Screw
4
2
183
1.5mm
Pin
89
2
Differential Shaft
128
Rear Differential Joint
2
92
Front Differential Joint
2
89
2
Differential Shaft
2
183
1.5mm
Pin
< >
#50000
#50000
< >
#300000
#300000
13
6
No.2
3 x 8mm
F/H Hex Screw
130
121
28
26
15
17
18
84
87
88
21
41
3x10mm
3x8mm
3x8mm
6
Front Bulk, Suspension Arm
7
No.2
7
Front Bulk, Suspension Arm
6
3x8mm
3x3mm
4x8mm
3x12mm
2.3mm
2
3 x 10mm
Button Hex Screw
2
3 x 12mm
F/H Hex Screw
3 x 3mm
Set Screw
2
4 x 8mm
Set Screw
2
2
4
3
1
After adjusting as per the diagram above, secure with 3x12mm F/H Hex Screw.
A
A
Horizontal
121
4.8mm
Ball Stud
2
84
Front Lower Arm Shaft
2
14
V-ONE R4
8
No.2
9
No.2
179
179
30
31
16
19
57
57
21
27
29
85
19
8
Front Bulk, Suspension Arm
9
Front Bulk, Suspension Arm
3x8mm
B
B
C
D
1 piece
A
A
A
Note the shape
(C)
(D)
Right
Left
C
3 pieces
D
When aligned to the groove at
the very front, belt tension
becomes looser.
Make sure to use the same
position for left and right sides.
Front Differential Assembly
(C)
(D)
185
Front Belt
3 x 8mm
F/H Hex Screw
4
2
179
10 x 15 x 4mm
Ball Bearing
< >Front Upper Arm
85
Front Upper Arm Shaft
2
Assy
< >
(C)
(D)
15
10
No.2
11
No.2
178
211
178
123
182
123
201
201
179
146
178
99
20
98
20
2
1
10
Front Bulk, Suspension Arm
11
Front Bulk, Suspension Arm
3x8mm
2x5mm
A
A
A
C
C
B
Tighten up.
18T Pulley Assembly
23T Pulley Assembly
< >Completed
< >Front Knuckle
2
3
4
5
6
1
2
2
178
6 x 12 x 4mm
Ball Bearing
2
178
6 x 12 x 4mm
Ball Bearing
179
10 x 15 x 4mm
Ball Bearing
2
182
2 x 11mm
Pin
2
2 x 5mm
Cap Screw
99
Middle Shaft
1
211
Wheel Shaft
2
4
123
9mm
Pillow Ball
201
10mm
Screw Cap
4
Hex Wrench (5mm)
98
2
< >Pulley
Firmly tighten the set screw onto
the flat surface.
B
3 x 8mm
Button Hex Screw
2
123
201
20
C
5.8mm
Pillow Ball
Assy
Assy
< >
< >
5mm
< >
16
12
No.2, No.10
124
191
151
12
Front Bulk, Suspension Arm
13
No.2
13
Front Bulk, Suspension Arm
124
Swing Shaft (Front)
2
Approx.2.5mm
Approx.3.5mm
3 x 6mm
Button Hex Screw
2
3 x 8mm
Button Hex Screw
2
98
98
3x8mm
3x8mm
3x6mm
3x6mm
98
2
< >Front Shock Stay
< >Front Knuckle
Use the hole second from bottom.
B
B
Cut off the fuel tube 2mm.
A
A
10mm0
5.8mm
Pillow Ball
2.5mm
3.5mm
< >
< >
17
14
No.3
15
No.3
3x6mm
202
174
174
97
64
63
95
96
67
94
98
96
159
3x8mm
3x6mm
0.5mm
14
Servo Saver
15
Servo Saver
A
Attach towards the front.
Front
C
1.0mm Offset
B
A
B
C
10mm0
98
3 x 6mm
Button Hex Screw
2
3 x 6mm
Button Hex Screw
1
3 x 8mm
Button Hex Screw
1
2
5.8mm
Pillow Ball
< >Completed
202
1
5.8mm
Pillow Ball
174
5 x 8 x 2.5mm
Ball Bearing
2
< >
18
81
81
93
approx. 32mm
16
No.3
16
Servo Saver
17
17
Servo Saver
81
5.8mm
Ball End
93
Steering Rod
2
The Side with groove is
reverse screw.
x2
A
A
4
Steering Rod
Steering Rod
< >Completed
< >Steering
< >Steering
< >
< >
< >
19
18
No.2, No.4
18
Center Bulk
19
No.2, No.4
19
Center Bulk
153
100
176
3 x 8mm
F/H Hex Screw
3x10mm
3x6mm
3x6mm
33
32
35
3x8mm
3x8mm
2.6x6mm
2.6x6mm
4
2
2.6 x 6mm
F/H Hex Screw
3 x 10mm
Button Hex Screw
2
3 x 6mm
Button Hex Screw
2
< >Belt Tensioner
20
No.2, No.4
20
Center Bulk
34
2.6x6mm
2
2.6 x 6mm
F/H Hex Screw
< >Battery Plate Mount
< >
< >
20
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
