Magnescale LH70 取扱説明書

LH70

Instruction Manual / Bedienungsanleitung /

Counter Unit / Anzeigeeinheit /

Read all the instructions in the manual carefully before use and strictly follow them.

Keep the manual for future references.

This instruction manual is for the LH70 series with software version 3.0 or later.

*To check the software version, refer to “10. Troubleshooting.”

Lesen Sie die ganze Anleitung vor dem Betrieb aufmerksam durch und folgen Sie beim

Betrieb des Geräts den Anweisungen. Bewahren Sie diese Bedienungsanleitung zum

späteren Nachlesen griffbereit auf.

Diese Bedienungsanleitung ist für die Serie LH70 mit der Software-Version 3.0 oder

später vorgesehen.

*Angaben zur Überprüfung der Software-Version finden Sie unter

„10. Überprüfungen zur Störungssuche und -Beseitigung“.

3.0 LH70

*10.

[For U.S.A. and Canada]

THIS CLASS A DIGITAL DEVICE COMPLIES WITH

PART15 OF THE FCC RULES AND THE CANADIAN

ICES-003. OPERATION IS SUBJECT TO THE

FOLLOWING TWO CONDITIONS.

(1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE

UNDERSIGNED OPERATION.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A

EST CONFORME À LA NORME NMB-003 DU

CANADA.

[For the customers in Australia]

Australian EMC Notice

This product complies with the following Australian

EMC standards.

AS/NZS 4252.1 /94 EMC Generic Immunity Part1

AS/NZS 2064 /92 Emission Standard for ISM

Equipment

[ For EU and EFTA countries ]

CE Notice

Marking by the symbol CE indicates compliance with

the EMC directive of the European Community. This

marking shows conformity to the following technical

standards.

EN 55011 Group 1 Class A/1998 A1/1999 A2/2002 :

"Limits and methods of measurement of radio

disturbance characteristics of industrial, scientific and

medical (ISM) radio-frequency equipment"

EN 61000-6-2/2001 :

"Electromagnetic compatibility (EMC) - Part 6-2 :

Generic standards - Immunity for industrial

environments"

Warning

When using this device with equipment governed by

Machine Directives EN 60204-1, measures should be

taken to ensure conformance with those directives.

Warnung

Wenn dieses Gerät mit Ausrüstungsteilen verwendet

wird, die von den Maschinenrichtlinien EN 60204-1

geregelt werden, müssen Maßnahmen ergriffen

werden, um eine Übereinstimmung mit diesen

Normen zu gewährleisten.

LH70

(E) (1)

Safety Precautions

Magnescale Co., Ltd. products are designed in full consideration of safety. However, improper

handling during operation or installation is dangerous and may lead to fire, electric shock or

other accidents resulting in serious injury or death. In addition, these actions may also worsen

machine performance.

Therefore, be sure to observe the following safety precautions in order to prevent these types of

accidents, and to read these "Safety Precautions" before operating, installing, maintaining,

inspecting, repairing or otherwise working on this unit.

Warning indication meanings

The following indications are used throughout this manual, and their contents should be under-

stood before reading the text.

Warning

Failure to observe these precautions may lead to fire, electric shock or other accidents resulting

in serious injury or death.

Caution

Failure to observe these precautions may lead to electric shock or other accidents resulting in

injury or damage to surrounding objects.

Symbols requiring attention

Symbols prohibiting actions

Symbols specifying actions

CAUTION ELECTRICAL

SHOCK

DO NOT

DISASSEMBLE

UNPLUG-

GING

(2) (E)

LH70

Warning

•Do not use the counter unit with voltages other than the indicated power voltage, and

do not connect multiple plugs to a single outlet as this may result in fire or electric

shock.

•Do not damage, modify, excessively bend, pull on, place heavy objects on or heat the

power cord, as this may damage the power cord and result in fire or electric shock.

•Do not handle the power plug with wet hands as this may result in electric shock.

•Do not open the cover of the counter unit to disassemble or modify the unit, as this

may result in burns or injury. These actions may also damage the internal circuitry.

Caution

•When unplugging the power plug, do not pull on the power cord as this may damage

the cord and result in fire or electrical shock. Be sure to grip the power plug when

unplugging it from the socket.

•The unit does not have an explosion-proof structure. Therefore, do not use the unit in

an atmosphere charged with inflammable gases as this may result in fire.

•When the unit will not be used for an extended period of time, be sure to unplug the

power plug from the socket for safety.

•Be sure to turn off the power before connecting or disconnecting power and signal

connectors in order to prevent damage or misoperation.

•The unit does not have an earthquake-proof structure. Therefore, do not use the unit

in moving areas or areas exposed to strong shocks.

•Do not use the electric cords packed with this product for any other product.

LH70

(E) i

Contents

1. Preface ............................................................................ 1-1

1-1. General Precautions ..................................................................................... 1-1

2. Features .......................................................................... 2-1

3. Name and Function of Each Part .................................. 3-1

3-1. Front Panel ................................................................................................... 3-1

3-2. Rear Panel .................................................................................................... 3-2

4. Installation and Connection of Unit.............................. 4-1

4-1. Accessories ................................................................................................... 4-1

4-2. Placement ..................................................................................................... 4-1

4-3. Connection ................................................................................................... 4-2

4-3-1. Connectable Measuring Unit....................................................... 4-2

4-3-2. Connection .................................................................................. 4-2

5. Settings ........................................................................... 5-1

5-1. Setting Processes and Setting Items ............................................................. 5-1

5-1-1. Process from Setting to Start of Operation ................................. 5-1

5-1-2. Description of Basic Settings .................................................... 5-1

5-1-3. Description of Detailed Settings ............................................... 5-2

5-1-4. Setting Keys ................................................................................ 5-3

5-1-5. Setting Method ............................................................................ 5-3

5-2. Settings for General-purpose Applications and

Milling Machine Function............................................................................ 5-4

5-2-1. When Power is Turned On for the First Time after

Factory Shipping ......................................................................... 5-4

5-2-2. Resetting the Basic Settings ........................................................ 5-5

5-2-3. Resetting the Detailed Settings ................................................... 5-6

5-3. Lathe Function Settings................................................................................ 5-7

5-3-1. When Power is Turned On for the First Time after

Factory Shipping ......................................................................... 5-7

5-3-2. Resetting the Basic Settings ........................................................ 5-8

5-3-3. Resetting the Detailed Settings ................................................... 5-9

5-4. Verifying Count Values during Addition Display....................................... 5-10

5-5. Compensation ............................................................................................. 5-11

5-5-1. Linear Compensation ................................................................ 5-11

6. Starting and Exiting Operation ..................................... 6-1

6-1. Power ON ..................................................................................................... 6-1

6-2. Starting Operation ........................................................................................ 6-1

6-3. Aborting Operation ...................................................................................... 6-2

6-3-1. Pausing Operation ....................................................................... 6-2

6-3-2. Restarting Operation ................................................................... 6-2

6-4. Exiting Operation (Power OFF) ................................................................... 6-2

ii (E)

LH70

7. Operation Method .......................................................... 7-1

7-1. How to Perform Key Operations .................................................................. 7-1

7-2. How to Use the Various Function ................................................................. 7-2

7-2-1. Zero Reset ................................................................................... 7-2

7-2-2. Inch/mm Selector ........................................................................ 7-2

7-2-3. Absolute/Incremental Mode Selection ........................................ 7-2

7-2-4. Halving ........................................................................................ 7-2

7-2-5. Addition Display Selection

(Only Avairable When Selecting Lathe Function) ...................... 7-3

7-2-6. Preset Mode ................................................................................. 7-3

7-2-7. Datum Point Mode ..................................................................... 7-5

7-2-8. “Tool Master (Tool No. 1)” and “Tool Offset (Tool No. 2 ~)”

(Lathe Applications) .................................................................. 7-10

7-2-9. Reference Point Mode

(How to Use the Measuring Unit with a Reference Point) ....... 7-15

8. Applied Functions .......................................................... 8-1

8-1. Canned Cycle Function ................................................................................ 8-1

8-1-1. Bolt Hole Circle Function ........................................................... 8-2

8-1-2. Simple R Cutting Function.......................................................... 8-4

9. Alarm Display ................................................................. 9-1

10. Troubleshooting ........................................................... 10-1

11. Specifications ............................................................... 11-1

12. Dimensions ................................................................... 12-1

LH70

(E) 1-1

Read all instructions carefully before use.

The LH70 counter unit will benefit you with reduced machining time and higher machining accuracy.

To make full use of the unit’s functions, read this instruction manual through carefully, and keep it properly

for future references.

1-1. General Precautions

When using Magnescale Co., Ltd. products, observe the following general precautions along with those

given specifically in this manual to ensure proper use of the products.

•Before and during operations, be sure to check that our products function properly.

•Provide adequate safety measures to prevent damage in case our products should develop a malfunction.

•Use outside indicated specifications or purposes and modification of our products will void any warranty

of the functions and performance as specified for our products.

•When using our products in combination with other equipment, the functions and performance as noted

in this manual may not be attained, depending upon the operating environmental conditions. Make a

thorough study of the compatibility in advance.

1. Preface

1-2 (E)

LH70

(E) 2-1

Minimum Display Resolution Switching

The minimum display resolution can be selected from the following.

Linear: 0.1 µm – 10 µm and diameter display

Angles: 1 second – 10 minutes

(Choose the appropriate setting for the direct measuring unit.)

(You can add other types of minimum display resolutions. See page 5-2.)

Machine Error Compensation

The LH70 compensates errors arising from the inclination or deflection of a machine tool, and displays the

actual displacement of the machine. Thus, the displayed value accords with the actual displacement of a

workpiece to achieve high-accuracy positioning and machining and restoration of machine tool accuracy.

(Linear compensation)

Data Storage

Data on display and preset data are held automatically.

Therefore, data is retained even after power is turned off or in case of a temporary power outage.

Preset

Each axis can have up to three preset values.

This is useful when setting multiple preset values.

Measuring Unit Reference Point Detection

Combining with a measuring unit with a reference point makes it possible to detect the measuring unit

reference point at all times.

This can be used as the reference point for machining.

You can also freely set the amount of reference point offset and easily restore it, which makes reference

point setting on a boring machine and the like very effective.

Multi Datum Point

You can keep a number of preset ABS coordinate datum points in memory (10).

Flicker Control

This reduces noticeable display flicker in cases such as when a high-resolution measuring unit is connected

or when the machine where the measuring unit is mounted is subjected to large vibrations.

2. Features

2-2 (E)

LH70

Milling Machine / Lathe

The basic settings can be used to select milling machine (general-purpose) function and lathe function.

Make the settings to match your operating environment. See Part 5, “Settings” for the setting procedure.

Milling Machine

Canned Cycle (2-axis and 3-axis models only)

•Bolt hole circle

Bolt hole positions are calculated and displayed by inputting the diameter and number of

holes.

•Simple R cutting

The arc cutting positions are calculated and displayed by inputting the radius, tool bore,

feed angle, and other data.

Lathe (3-axis model only)

•Tool coordinating

The provided number of coordinates can be set as tool coordinates, and the coordinate of

any cutting tool can be retrieved with a tool number (12 coordinates).

• Adding

The sum of the reading from the measuring unit mounted on the lathe’s cutting tool holder

and the reading from the measuring unit mounted on the carriage can be displayed to show

the exact position of the cutting edge of the tool.

2. Features

LH70

(E) 3-1

3-1. Front Panel

3. Name and Function of Each Part

No. Name Function

1Axis label Axis lamp Lights up: Axis being measured

Flashing: Selected axis

2Lamp display ABS lamp Lights up: When displaying absolute value (ABS mode)

Goes out: When displaying incremental value (INC mode)

φ lamp Lights up: When displaying diameter

Goes out: Normal display

3Counter display From the top: Display 1 (X, Z), Display 2 (Y, Z), and Display 3 (Z)

Shows status with alphabetical letters when making mode settings

An alarm display is shown in case of error (see Part 9)

4RESET key Resets incremental value to zero

Switches to INC mode during ABS mode

5P key Presets values (mode lamp will be lights up when selected)

Calls up values (mode lamp will be lights up when selected)

6 key (Datum Point Setting key) Used to go into datum point mode (mode lamp will be lights up when

selected)

7REF key Used to detect measuring unit reference point (mode lamp will be lights up

when selected)

8ABS/INC key Switches between ABS mode and INC mode

9SET UP key Used to make various settings

!PROG key Not usable

" key (Canned Cycle key) Used to perform predetermined routines, such as bolt hole circles

#Status lamp Will lights up or be flashing when performing an operation or in a mode

$RUN/NEXT key Used to run a canned cycle operation

%EDIT key Used to change a canned cycle, a preset value, etc.

& key (Standby key) Turns power ON and OFF

Lamp in upper left Lights up: Power is OFF Flashing: Startup

Goes out: Power ON

( key (Select Axis key) Selects axis

Selects setting content

Selects digit of setting value

)Numeric key Value input

~Function key Used to perform various operations

1/2 key Halves the displayed value

key Advances to next item when making settings or canned cycle operation

CE Cancels value input and various function key operations

ENT key Finalizes settings

12 4536789!

#

$

&

~)(

%

"

3-2 (E)

LH70

3-2. Rear Panel

No. Name Function

1Measuring unit input 1/2/3 Performs measuring unit input for first, second and third axes

2Expansion port Not usable on this model. Do not remove the cover.

3DC input terminal DC power input terminal

Note

Always use the special AC adaptor (sold separately). Using any other

adaptor could damage the counter unit or cause it to malfunction.

4AC adaptor cable clamp Anchors the AC adaptor cable

5Ground terminal Note

Use the included grounding wire when setting up the counter unit, and

always connect this terminal to the machine proper that you are setting up.

3. Name and Function of Each Part

12

34 5

LH70

(E) 4-1

4-2. Placement

Environmental conditions

•Ambient temperature: 0 – 40°C (32 to 104°F)

•For indoor use

•Place counter unit so it is protected from coolant, machine oil, chips and the like

•Place counter unit at least 50 cm from power switchboards, welders and the like

Notes

•Do not completely cover the counter unit with a vinyl cover or put it in a sealed case.

•If the counter unit’s power is suddenly cut off, or if the voltage temporarily falls below the usable range,

the alarm may sound and faulty operation may occur. If such a situation occurs, temporarily unplug the

AC adaptor, wait a few seconds, reinsert the AC adaptor and repeat the operation from the beginning.

4. Installation and Connection of Unit

Be careful where you

place the counter unit.

Place the counter unit so it is pro-

tected from cutting chips and the like.

Switchboard

(Locate more than 0.5 m/20" away.)

Machine oil

Chips

Welder

Coolant

Chips

→

4-1. Accessories

Ground wire 1

Anchor bolts M4 × 16 2

Instruction Manual 1

Supplement 1

4-2 (E)

LH70

4-3. Connection

4-3-1. Connectable Measuring Unit

Model Measuring unit resolution Type of connection

SJ300 Series 1 µm Direct

GB-A Series 0.5 µm Through adaptor (sold separately)

PL20B Series 10 µm Through adaptor (sold separately)

DG-B Series 0.5 µm Through adaptor (sold separately) + DZ51

Adaptor (sold separately): SZ70-1

4-3-2. Connection

Be sure to provide power to the AC adaptor only after all other connections have been made.

Notes

•Fasten the connecting cables to stationary members to prevent accidental disconnection.

•Be absolutely sure to turn off the AC power to the AC adaptor of the counter unit before inserting or

removing measuring unit connector or before replacing the measuring unit. Do not plug in or unplug the

DC output connector on the counter unit side.

•Do not route connecting cables through the same duct as the machine power line.

1Secure the counter unit to the installed bracket.

Anchor bolts (supplied): M4 × 16 (2 pcs.)

2Secure the measuring unit.

3Connect the measuring unit connector to the measuring unit input on the counter unit rear side.

Be sure to always check “Connections when using the addition function with lathe function” on

page 4-4 before making the connections.

4Install the AC adaptor.

Note

Do not provide power to the AC adaptor in this step.

5Remove the cable clamp on the counter unit rear side.

6Connect the DC output connector to the DC input terminal.

7Attach the cable of the DC output connector to the cable clamp removed in step 5, and then secure in

place.

Note

Secure while being careful not to apply force to the connector.

8Connect the ground wire.

9Provide power to the AC adaptor.

lights up for about 2 seconds on display 1, and then (3-axis model) or

(1 or 2-axis model) is displayed.

is displayed on the connected displays (1 to 3).

4. Installation and Connection of Unit

LH70

(E) 4-3

For the connections when using the addition function with lathe function, see page 4-4.

Ground wire

Screw down firmly.

Clamp cable to prevent

connector from pulling out.

Make sure that force is not

being applied to connector.

Bracket

M4 × 16 anchor bolts,

2 pcs. (supplied)

PSC-21/22/23 AC adaptor (sold separately)

100 - 240 VAC±10% 50/60 Hz

* Get power from lamp line.

Measuring

unit input

First axis

2

3

DC output connector

4. Installation and Connection of Unit

4-4 (E)

LH70

Connections when using the addition function with lathe function

*1To the second

or third axes

Screw down firmly.

Clamp cable to prevent

connector from pulling out.

Make sure that force is not

being applied to connector. Bracket

M4 × 16 anchor bolts, 2 pcs.

(supplied)

PSC-21/22/23 AC adaptor (sold separately)

100 - 240 VAC±10% 50/60 Hz

* Get power from lamp line.

Measuring unit input

First axis

2

3

DC output connector

*1To the

second or

third axes

To the first axis

*1If the resolutions of the measuring units performing the addition (Z1-axis, Z2-axis) are different, be sure

to connect the measuring unit with higher resolution to the second axis of the counter unit.

Example: Using measuring unit Z1 (resolution: 0.5 µm) and measuring unit Z2 (resolution: 1 um)

Measuring unit Z1 (resolution: 0.5 µm) : Connected to counter unit second axis

Measuring unit Z2 (resolution: 1 µm) : Connected to counter unit third axis

Z2-axis

Measuring unit

X-axis Z1-axis

Ground

wire

4. Installation and Connection of Unit

LH70

(E) 5-1

5. Settings

This describes how to make the settings for the connected measuring unit, operating conditions, and other

situations for using the counter unit.

If the settings are made incorrectly, counting will not be performed properly.

The first time you turn the power ON after purchasing the counter unit, the unit will automatically go into

Settings mode.

5-1. Setting Processes and Setting Items

5-1-1. Process from Setting to Start of Operation

Settings are divided into the basic settings and detailed settings.

1When power is turned on for the first time after factory shipping:

Power ON H Basic settings H Detailed settings HStart of operation

2When changing the basic settings:

Power ON H Basic settings H Detailed settings HStart of operation

3When changing the detailed settings only:

Power ON H Detailed settings HStart of operation

5-1-2. Description of Basic Settings

This sets the functions that are used, region, resolution of the connected measuring unit, and other basic

system settings.

When the “basic settings” are set or changed, the “detailed settings” will revert to their factory

default settings.

*If you have already entered the “detailed settings”, make a note of the setting values before resetting or

changing the “basic settings”.

Setting item

Model

Addition

display (Lathe

only)

Destination

country

Measuring unit

resolution

Factory setting Available options

:Milling machine

(for general-purpose applications)

:Lathe

: No addition, second axis count value

:No addition, third axis count value

: second axis +third axis count value

:second axis –third axis count value

:–second axis +third axis count value

:–second axis –third axis count value

: Standard (mm display; inch display possible)

:U.S. (inch display; mm display possible)

:Japan (mm display only)

:Linear scale 0.1 µm

:Linear scale 0.5 µm

:Linear scale 1 µm

:Linear scale 5 µm

:Linear scale 10 µm

:Rotary scale 1 s

:Rotary scale 10 s

:Rotary scale 1 min

:Rotary scale 10 min

:Linear scale 0.05 µm

:Linear scale 2 µm

:Linear scale 20 µm

:Linear scale 25 µm

:Linear scale 50 µm

:Linear scale 100 µm

:Rotary scale 1 degree

Remarks

Select the model specifications that you are

using.

This is the display setting for the count value.

It is shown on display 2.

This enables the user to find out the exact

position of the cutting edge of the tool in the

addition display.

*See Part 5-4, “Verifying Count Values during

Addition Display”.

Select the appropriate unit of measurement.

Make this setting to match the measuring unit

resolution.

The indications corresponding to inputs 1, 2

and 3 of the measuring unit are fixed

regardless of how the display is switched

(“Detailed Settings”).

The polarity is switched by the key.

Expanded selection options are made

available by pressing the key.

*When using the addition function in the

lathe function (ADD settings), the error

sound will be made when setting the

resolution if the connection is incorrect.

(See page 4-4 for the connections.)

Count display

Tool No. display

Measuring unit output

Minimum resolution

A

B

5-2 (E)

LH70

5-1-3. Description of Detailed Settings

This sets the polarity, display resolution, compensation values, and other settings for the actual operating

conditions.

When the power is turned on for the first time after factory shipping, the “detailed settings” cannot be made

unless the “basic settings” have been completed.

If the “basic settings” are set or changed, all of the “detailed settings” will revert to the

factory default settings.

*If you have already entered the “detailed settings”, make a note of the setting values before resetting or

changing the “basic settings”.

5. Settings

Setting item

Minimum display

resolution

Display switching

(2-axis and 3-axis

models with

general-purpose/

milling machine

specifications only)

Axis label

switching (1-axis

and 2-axis models

with general-

purpose/milling

machine function

only)

Compensation

value

Flicker control

Sleep

Factory setting

Automatic setting

for measuring unit

resolution values

Measuring

unit input Display

1 –––––––––– 1

2 –––––––––– 2

3 –––––––––– 3

DisplayAxis label

1 –––––––––– X

2 –––––––––– Y

3 –––––––––– Z

Available options

Measuring unit resolution and higher

Diameter display (except for angle

display)

Polarity (+/–)

:Measuring unit input 1

:Measuring unit input 2

:Measuring unit input 3

:Nothing displayed

Display 1...X/Z

Display 2...Y/Z

Display 3...Z

:No setting

:(Enter the linear

compensation value)

:No setting

:Weak

:Strong

:No setting

:1 minute

:5 minutes

:10 minutes

:30 minutes

:60 minutes

Remarks

This sets the resolution that is

displayed. The setting may vary

depending on the setting for the

measuring unit resolution in the

“basic settings”.

For the lathe function, the diameter

display can be used to display twice

the amount of the cut of a cutting

tool. Set the polarity so that the

value of the cutting direction (X-axis)

decreases.

During diameter display, φ will light

up in lamp display mode.

*Pressing the key enables

you to add the type of minimum

display resolution.

This is the measuring unit input and

display 1/2/3 combination. The count

display location (display 1/2/3) can

be changed without reconnecting

the measuring unit input. The

respective settings are linked to the

selected option.

This is the display 1/2/3 and axis

label combination.

*See Part 5-5, “Compensation”.

Reducing display flicker.

OFF status shows the most accurate

status.

The display is turned off if no

operations are performed for a

preset time.

X

1-axis model

X or Z

2-axis model

Xor Xor Z

YZY

LH70

(E) 5-3

5-1-4. Setting Keys

Be sure to also use the numeric keys to enter setting values.

5-1-5. Setting Method

1When power is turned on for the first time after factory shipping

General-purpose applications and milling machine function →Go to Part 5-2-1

Lathe function →Go to Part 5-3-1

2When changing the basic settings

General-purpose applications and milling machine function →Go to Part 5-2-2

Lathe function →Go to Part 5-3-2

3When changing the detailed settings only

General-purpose applications and milling machine function →Go to Part 5-2-3

Lathe function →Go to Part 5-3-3

5. Settings

5-4 (E)

LH70

5-2. Settings for General-purpose Applications and Milling Machine Function

5-2-1. When Power is Turned On for the First Time after Factory Shipping

(General-purpose Applications and Milling Machine Function)

1STD/US/JPN

20.1/0.5/1/5/10/

00.00.01/

00.00.10/

00.01.00/

00.10.00

0.05/2/20/25/

50/100/

01.00.00

3Setting at 2 or

higher/Diameter

display at 2

(except for

angle)/Polarity

4IN-1/IN-2/IN-3/

IN -

5X/Y/Z

6OFF/LIN Err

* See Part 5-5,

“Compensation”.

7OFF/1/2

8OFF/1/5/10/30/

60

1

2

3

4

5

6

7

8

Power ON

Basic

settings

Start of operation

(When the minimum display resolution is 0.001 mm)

Detailed

settings

Model

Destination

country

(STD)

Measuring unit

resolution

(1)

Minimum display

resolution

(Measuring

unit resolution)

Display

switching

(1-1, 2-2, 3-3)

For 2-axis and

3-axis models only

For 1-axis and

2-axis models only

Axis label

switching

(1-X, 2-Y, 3-Z)

Compensation

value

(OFF)

Flicker control

(OFF)

Sleep

(OFF)

Select axis

Performed for each axis.

or

Note 1

1-axis/2-axis model

3-axis

model

Approx.

2 seconds

Use and to select setting content

Select axis

Performed for each axis.

Use to select setting content

Select axis

Use to select setting content

Performed for each axis.

Select axis

Performed for each axis.

Use to select the setting (compensation), and then set each option

Enter the compensation value

Select axis

Use to select setting content

Use to expand the selection option.

or

∗ The setting in parentheses ( ) is the factory setting.

∗ indicates the process when the setting does not be changed.

Note 1: Use to return

to or .

Use to select setting content

or

5. Settings

ページが読み込まれています...

Magnescale LH70 取扱説明書

Magnescale LH70 取扱説明書

他の言語で

関連論文

その他のドキュメント