FP-7F

Roland FP-7F, FP-4F, FP-50, FP-80 取扱説明書

  • Roland FPシリーズKSC-76とKSC-44キーボードスタンドの取扱説明書を読みました。組み立て方、ヘッドホンフックの取り付け方、ピアノの設置方法など、このスタンドに関するご質問にお答えできます。安全な使用方法についても説明されていますので、ご不明な点があればお気軽にご質問ください。
  • KSC-76とKSC-44の違いは何ですか?
    組み立てに電動工具を使っても良いですか?
    スタンドを移動する際は、どのような点に注意すれば良いですか?
    組み立て時にペダルコードや電源コードを挟まないようにするにはどうすれば良いですか?
Keyboard stand for FP series
KSC-44
KSC-76
* Before using this stand, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES. Additionally, the manual should be saved
and kept on hand as a convenient reference.
Before you begin assembling the stand, check that all the parts were
supplied.
1
2
5
(KSC-44)
3
(KSC-76)
4
(KSC-76)
A BC
KSC-76 KSC-44
A Side board (left) 1
B Side board (right) 1
C Center board 1
1 Screw “a (M6 x 18 mm) 4
2 Knob bolt 4
3 Headphone hook “a“ 1
4 Screw “b” (M4 x 16 mm) 2
A Side board (left) 1
B Side board (right) 1
C Center board 1
1 Screw “a (M6 x 18 mm) 4
2 Knob bolt 4
5 Headphone hook “b“ 1
Owners Manual
Make sure that another person is on hand to help with the assembly and setup.
Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your
hands or feet.
Prepare an area in which you can perform the assembly safely.
Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or
stripping the screws.
The KSC-76 is designed speci cally to be used with the FP-80.
Assembly Procedure
Parts Check
* You will also need to have a Phillips screwdriver.
* Fasten each screw tightly, then place the stand in a stable and horizontal place.
* Do not allow the pedal cord or power cable to get twisted or pinched while
assembling the stand.
1 Stand Assembly
At  rst, assemble the entire stand in a temporary fashion, without really
tightening the screws. Then, after checking the overall alignment of the
boards (and gently shifting certain parts where necessary), go around and
tightly fasten each of the screws.
1. Attach the side board (right) for the right sides to the center
board (so that the metal parts face inside) using screws a” (M6
x 18 mm).
2. Use screws a (M6 x 18 mm) to attach the side board (left) in
the same way.
12
Center board
Side board (right)
Side board (left)
Screw “a (x 4)
2 Installing the Piano on the Stand
1. Set the piano on the stand, then  rmly attach the four knob
bolts.
* When handling the piano,  rmly grasp it. Be careful, so you do not get your  ngers
pinched.
Please don’t get your  ngers
pinched!
Knob bolt (x 4)
Side board
Underneath
the Piano
3 Attaching the Headphone Hook
1. Attach the headphone hook “a using screws “b“ (M4 x
16 mm).
Screw “b” (x 2)
Headphone
hook “a“
KSC-76
1. Press and twist the headphone hook “b“ included with
the piano into the hole in the bottom of the piano (refer
to the  gure below).
2. Turn the thumbscrew of the headphone hook “b“ to
secure the headphone hook “b“.
Headphone
hook “b“
KSC-44
* In the interest of product improvement, the speci cations and/or appearance of this
unit are subject to change without prior notice.
Keyboard stand for FP series
KSC-44
KSC-76
IMPORTANT NOTES
Copyright © 2013 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland is a registered trademark of Roland Corporation in the United States and/or other countries.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
About WARNING and CAUTION Notices
About the Symbols
ALWAYS OBSERVE THE FOLLOWING
USING THE UNIT SAFELY
Placement
Do not expose this stand to direct sunlight, place
it near devices that radiate heat, leave it inside
an enclosed vehicle, or otherwise subject it to
temperature extremes. Also, do not allow lighting
devices that normally are used while their light
source is very close to this stand (such as a piano
light), or powerful spotlights to shine upon the
same area of this stand for extended periods of
time. Excessive heat can deform or discolor this
stand.
Maintenance
To clean this stand, use a dry, soft cloth; or one that
is slightly dampened. Try to wipe the entire surface
using an equal amount of strength, moving the
cloth along with the grain of the wood. Rubbing
too hard in the same area can damage the  nish.
Never use benzine, thinners, alcohol or solvents of
any kind, to avoid the possibility of discoloration
and/or deformation.
Additional Precautions
When you need to transport this stand, package
it in the box (including padding) that it came
in, if possible. Otherwise, you will need to use
equivalent packaging materials.
Cautions When Moving The Piano
You must use two or more people when moving
the piano.
Before moving the piano, disconnect the AC
adaptor and other cables.
Keep the piano level when lifting it.
Be careful not to pinch your hands or drop the
piano on your feet.
WARNING
Do not disassemble or modify by yourself
Do not open or perform any internal
modi cations on this stand. (The only
exception would be where this manual
provides speci c instructions which should
be followed in order to put in place
user-installable options.)
Do not repair or replace parts by yourself
Do not attempt to repair this stand, or
replace parts within it (except when this
manual provides speci c instructions
directing you to do so). Please consult an
authorized Roland distributor or the nearest
Roland Service Center; a list of these can be
found in the owner’s manual for the device
to which you are using.
Do not use or store in the following types of locations
Subject to temperature extremes
(e.g., direct sunlight in an enclosed
vehicle, near a heating duct, on top of
heat-generating equipment); or are
Damp (e.g., baths, washrooms, on wet
oors); or are
Exposed to steam or smoke; or are
Subject to salt exposure; or are
Humid; or are
Exposed to rain; or are
Dusty or sandy; or are
Subject to high levels of vibration and
shakiness.
Do not place in an unstable location
Make sure you always have this stand placed
so it is level and sure to remain stable. Never
place it on stands that could wobble, or on
inclined surfaces.
Adults must provide supervision in places where
children are present
When using this stand in locations where
children are present, be careful so no
mishandling of this stand can take place. An
adult should always be on hand to provide
supervision and guidance.
WARNING
Do not drop or subject to strong impact
Protect this stand from strong impact.
(Do not drop it!)
CAUTION
Use the stand only for the speci ed products
This stand is designed speci cally to be used
with the Roland products (KSC-76: FP-80,
KSC-44: FP-50 and FP-7/4 series). If used
in combination with other products, you
risk sustaining injuries as the result of the
product dropping down or toppling over
due to a lack of stability.
Evaluate safety issues before using stands
Even if you observe the cautions given in the
owner’s manual, certain types of handling
may allow this product to fall from the stand,
or cause the stand to overturn. Please be
mindful of any safety issues before using this
product.
Avoid climbing on top of this stand, or placing heavy
objects on it
Never climb on top of, nor place heavy
objects on this stand.
Keep small items out of the reach of children
To prevent accidental ingestion of the parts
listed below, always keep them out of the
reach of small children.
Included screws
Knob bolts
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US
(
Proposition 65
)
/