Ruark Audio R3 Compact Music System ユーザーマニュアル

R3 Compact Music System

R3 Comapct Music System

User guide

EN

Important information about

the AC power adapter

Model DYS836-140285W-K

Input 100-240V~50/60Hz 1.0A MAX

Output 14.0V 2.85A

Class II, Efciency Level VI

• This AC adapter is for audio & video equipment use

only and complies with IEC 60065 safety standard.

• The supplied 3-pin plug adapter complies with

BS 1363-1 and the supplied 2-pin plug adapter

complies with EN 50075.

• Before using the AC adapter, ensure the mains voltage

is within the rated supply voltage range.

• The output power taken from this AC adapter must not

exceed its rated output power.

• DO NOT disassemble or modify the AC adapter.

• DO NOT drop or throw the AC adapter.

• The external exible cable cannot be replaced and if

the cord is damaged, the AC adapter must be replaced.

• DO NOT expose the AC adapter to dripping or

splashing water, and do not place objects lled with

liquids, such as vases, on or near the device.

• DO NOT leave the AC adapter in a hot location, such as

near re or under strong sunlight.

• Unplug the AC adapter during lightning storms or

when unused for long periods of time to prevent

damage.

• Ensure that the AC adapter is readily accessible when

plugged into the mains. If an abnormal condition occurs

while using it, immediately turn off the connected

device and disconnect the mains adapter from the

mains.

• DO NOT dispose this AC adapter as general household

waste or unsorted municipal waste. Dispose of it

according to local regulations.never cover ventilation

openings on the device.

Safety and regulatory

information

● Read this user guide and follow all instructions, it will help you set up

and operate your product properly.

● Heed all warnings and keep this user guide for future reference.

● Do not attempt to use a damaged device as this could result in a

dangerous electric shock.

● Do not open the unit or remove any panels to expose the electronics.

No user serviceable parts inside.

● Refer all servicing to qualied service personnel. Servicing is required

when the device has been damaged in any way, such as when any

power cord, or power plug is damaged, liquid has been spilled or

objects have fallen into the device, the device has been exposed to

rain or moisture, does not operate normally, or has been dropped.

● This device is intended to be operated ONLY from the AC voltages

listed on the back panel or included AC mains adapter. Operation from

voltages other than those indicated may cause irreversible damage to

the device and void the product warranty.

● Ensure that the mains plug or mains connector into the unit is readily

accessible in case disconnection from the mains is required.

● The AC mains adapter, mains plug, or mains connector must be

removed from the socket to completely disconnect the system from

AC mains power.

● Do not place any naked ame sources, such as lighted candles, on or

near the device. Do not install near any heat sources such as radiators,

stoves, or other devices that produce heat.

● Avoid exposure to extreme heat or cold.

● Only use attachments/accessories specied for this device. Make no

modications to the system or accessories. Unauthorised alterations

may compromise safety, regulatory compliance, and system

performance.

● Only use the supplied aerial or an approved replacement.

● To reduce the risk of re or electrical shock, do not expose the device

to rain or moisture. Do not expose this device to dripping or splashing,

and do not place objects lled with liquids, such as vases, on or

near the device. As with any electronic products, use care not to spill

liquids into any part of the system. Liquids can cause a failure and/or

a re hazard.

● Disconnect this device from AC mains power during lightning storms

or when unused for long periods of time to prevent damage to this

device.

● To prevent risk of re or electric shock, avoid overloading AC mains

power outlets or extension cords.

● Long-term exposure to loud music may cause hearing damage. It is

best to avoid extreme volume when using headphones, especially for

extended periods.

● Do not install this device in a conned space. Always leave a space

of at least 10cm around the device for ventilation and ensure that

curtains or other objects never cover ventilation openings on the

device.

This device is labelled in accordance with European Directive

2012/19/EU concerning waste electrical and electronic

equipment. This symbol indicates that the product or

associated batteries should not be disposed of as general

household waste. As with any electrical equipment, please

dispose of it according to local regulations.

CE COMPLIANCE INFORMATION

This product conforms to all EU Directive requirements as applicable by

law. Hereby, Ruark Audio, declares that this device complies with the

essential requirements and other relevant provisions of the European

Radio Equipment Directive 2014/53/EU.

You can download the full CE Declaration of Conformity at

www.ruarkaudio.com/doc/R3doc.pdf

EN

Speciﬁcations

Ampliﬁers and drivers

2 × 75mm Ruark NS+ drivers

30W Class AB power amplier

Enhanced digital 3D audio processor

Tuner

DAB, DAB+ and FM Tuner with RDS

75 Ohm F-type DAB/FM aerial connector

CD player

CD, CD-ROM, CD-R/RW

MP3, WMA, AAC up to 320 kbit/s

Digital audio

Internet radio, Spotify Connect, Amazon Music, Deezer,

TIDAL, UPnP™ DLNA

Wi-Fi 802.11a/b/g/n supports WEP, WPA & WPA2 security

MP3, WMA, AAC, FLAC, WAV

Bluetooth: V4.0 SBC, AAC, A2DP, aptX

Inputs and outputs

Digital optical input (TOSLINK) 24-bit 192kHz

Line input (RCA) 2.3Vrms max

Line out (RCA) 2.0Vrms

Ethernet (RJ45)

USB 2.0, 5W (5V 1A)

3.5mm stereo jack headphone output

Power

AC mains adapter input: 100-240V AC 50/60Hz 1A

AC mains adapter output: 14V DC 2.85A

Nominal consumption: 5W

Standby consumption: 2W

Remote batteries: 2 x 1.5V AAA

Physical

H167 x W420 x D220mm (H6.6 x W16.5 x D8.7in)

5.3kg (11.7lbs)

Specication and design subject to modication without

notice.

Ruark Audio assumes no responsibility for any errors that

may appear in this manual and the information contained

in it may change without notice.

Troubleshooting

For help with your product, please refer to the FAQ

(Frequently Asked Questions) page in the support area of

our website.

For more information visit www.ruarkaudio.com/support.

What’s in the box

Ensure that all parts listed below are in

the box.

If any part is missing, do not use the R3

and contact us directly if purchased in

the UK, or your Ruark Audio dealer if

purchased outside the UK.

1. R3

2. Remote control

3. Remote batteries (2x 1.5V AAA)

4. Antenna spanner

5. Telescopic antenna

6. AC power adapter

7. Plug(s) for AC power adapter*

8. Quick start guide

If possible, please retain the carton and

all packaging materials.

1

3

4

5

6

8

72

* The number and type of plug adapters

supplied will vary according to region.

EN

Controls

9. – STANDBY

10. CONTROL KNOB / SELECT

Rotate to adjust volume from a Now Playing screen

Rotate to browse menus, tracks or station lists*

Press to SELECT

11.

– press to skip to next station or track, press

and hold to fast forward. In standby, press to

increase display brightness.

12.

– press to skip to previous station or track,

press and hold to rewind. In standby, press to

decrease display brightness.

13. PRESET – press to recall a saved station or

playlist, press and hold for two seconds to save a

station or playlist

14. SOURCE – press to change audio source

15.

– press to play/pause a track or mute audio

inputs and radio

16. MENU – press to view the menu

17. BACK – press to return to the previous menu or list

screen

18. INDICATOR LIGHT

Indicates your music system is on and ashes

when Bluetooth is ready to pair or when using the

remote.

*You can also press

or to browse menus, tracks,

sources or station lists.

How long you press a key is important

Press = tap or press and immediately release

Press and hold = press and release after two seconds

9

11

12

13

14

10

16

17

15

18

Remote

19. – STANDBY

20.

SOURCE – press to change audio source.

21. INCREASE VOLUME

22.

/ SELECT – press to play/pause a track,

mute/unmute radio or to select a menu item.

23.

– press to skip to previous station or

track, press and hold to rewind. In standby,

press to decrease display brightness.

24.

– press to skip to next station or track,

press and hold to fast forward. In standby,

press to increase display brightness.

25. DECREASE VOLUME

26.

BACK – press to return to the previous

menu or list screen.

27.

MENU – press to view the menu.

28.

PRESET – press to recall a saved station

or playlist, press and hold for two seconds to

save a station or playlist.

29. PRESET 1

30. PRESET 2

31. PRESET 3

+

-

+

-

21

25

19

26

29

31

30

23

20

22

27

24

28

EN

40

39 41

42

46

45

44

43

343332 35 36 3837

Overview

32. Remote receiver

33. Ambient light sensor

34. CD eject button

35. OLED display

36. Controls

37. CD loading slot

38. 75mm Ruark NS+ drivers

39. USB C (5V 1A)

40. Optical input

41. Ethernet

42. DAB-FM antenna

43. DC power input (14V 2.85A)

44. Line in (phono)

45. Line out (phono)

46. Headphone out (3.5mm jack)

Getting started

1 Insert batteries into remote control

2 Connect the aerial

Fit the telescopic aerial to the DAB/FM antenna socket

on the back of your R3 and gently tighten it using the

supplied spanner.

3 Connect to AC mains power

Fit the correct plug for your region to the mains adapter;

it will “click” into place. Connect the mains adapter to the

DC power socket on the back of your R3, then connect it

to the mains socket.

4 Switch on

Press to turn the R3 on.

5 Select language

Rotate the CONTROL KNOB until your preferred choice

is highlighted, then press SELECT.

6 Setup wizard

Follow the setup wizard to congure the clock and

connect to your network.

To start the setup wizard, rotate the CONTROL KNOB to

highlight YES and then press the knob to SELECT.

If you choose NO, your R3 will start without conguring

the time/date and network settings.

7 Select a source

When your setup is complete, your R3 will display

a menu with a list of the available sources. Use the

CONTROL KNOB to choose a source and press

SELECT.

8 Enjoy your music!

App control

You can also control your R3 using UNDOK. Find it on

the Apple/Android app store.

For more information visit www.ruarkaudio.com/app

EN

Common functions

Switch on and to standby

Press STANDBY to turn your music system on. Press

again to switch to standby.

Now Playing screens

Unless you’re adjusting a setting, the screen will look

similar to the example below with the clock above and

station/track/album/artist information below.

The on-screen icons below are shown when their

respective functions are active.

Alarm Sleep timer

Shufe Repeat

Menu screens

The menus enable you to set the various options

such as adjusting the bass and treble. To change a

setting, press MENU to display the list of available

options, rotate the CONTROL KNOB to highlight the one

you wish to change, then press the knob to conrm your

selection.

System

Audio

Network

Date and time

Brightness

Language

Browsing menus, track and station lists

To change settings – press MENU

To scroll through options – rotate CONTROL KNOB

To select option – press CONTROL KNOB

To exit menu – press MENU or wait for a few seconds

To return to the previous menu/list – press BACK

How long you press a key is important

Press = tap or press and immediately release

Press and hold = press and release after two seconds

Adjust volume

Rotate the CONTROL KNOB from any Now Playing

screen.

Speaker volume and headphone volume are adjusted

separately, so when headphones are plugged in the

volume is shown as Volume (HP).

NOTE: rotating the CONTROL KNOB when a menu or

track/station list is displayed will scroll through the menu

and not change the volume.

Change audio source

Press SOURCE to view the current source, rotate the

CONTROL KNOB to cycle through the list of sources,

then press the knob to select one currently displayed.

(You can also press SOURCE repeatedly to cycle through

the list of sources instead of rotating the knob.)

Pause track or mute audio

Press and then press again to resume listening.

Play next/previous track

Press to skip to the next track in the folder or album,

press to skip to the start of the current track, press

again to skip to the previous track.

Fast forward or rewind track

Press and hold or (may not work with Bluetooth).

Change FM radio station

Press or to seek the next or previous station.

Change DAB radio station

Press or to tune to the next or previous station.

You can also view the multiline station list by selecting

MENU > Station list.

Change station or track information

Change the station/track information displayed by

selecting one of the options from MENU > Info.

Save radio station preset

Press and hold PRESET until ‘Save preset’ is shown

then rotate the CONTROL KNOB to choose the preset

number and press the knob to save the current station.

Presets are either marked with the station name,

frequency or as ‘[Not set]’.

If you save a station over an existing preset, the new

station will replace it.

Recall radio station preset

Press PRESET, rotate the CONTROL KNOB to scroll

through the preset station list, then press the knob to

select a station.

To return to the previous menu level or station list,

press BACK

EN

Connect a Bluetooth device

When you change the source to Bluetooth, your R3 will

attempt to automatically connect to the last connected

device. If you have not yet paired your device or the

previous device is not available, your R3 will enter into

pairing mode.

To disconnect the current device and connect a new one,

select MENU > Connect device.

Headphones

Connect your headphones to the 3.5mm stereo jack

socket on the front of your R3.

Headphone volume is adjusted independently from

speaker volume, so when headphones are plugged in the

volume is shown as Volume (HP).

USB charging

The USB socket on your R3 is rated at 5W (5V 1A)

and will power most smart devices and USB powered

accessories.

Music streaming services

Spotify Connect

Use your phone, tablet or computer as a remote control

for Spotify. Go to spotify.com/connect to learn how.

Amazon Music

For more details, visit www.amazon.com

Deezer

For more details, visit dzr.fm/airable

TIDAL

For more details, visit tidal.com/try-now

The range of supported music services may change

without notice.

Please note that: MENU > System > Audio means

press MENU, select System and nally select Audio

System settings

Bass and treble

MENU > System > Audio > Bass or Treble level

Loudness

Loudness automatically boosts the treble and bass

frequencies at lower volumes.

MENU > System > Audio > Loudness

3D sound

3D widens the stereo sound stage and creates a more

immersive and involving sound.

MENU > System > Audio > 3D

Date and time

MENU > System > Date and time

The time and date are automatically synchronised with

national time signals broadcast over DAB, network

and FM (FM time synchronisation may not always be

available).

You can also set the time manually by turning auto

update off and change the time and date format.

Display brightness

MENU > System > Brightness

Independently adjust the brightness of the display when

your R3 is on and in standby.

When the brightness is set to 0 the display will

automatically switch off after a few seconds. The display

will then briey illuminate whenever any key is pressed.

You can also adjust the standby brightness when your R3

is in standby by pressing

or .

Language

MENU > System > Language

Change the menu language.

Software update

MENU > System > Software update

Your R3 is set to automatically check for software

updates. If one is available, you will be asked whether

you want to download and install it.

CAUTION: Disconnecting the power during a software

update could permanently damage your R3.

Factory reset

MENU > System > Factory reset

Resets all settings and clears presets.

EN

Currently saved settings are marked with an asterisk ( )

Setup wizard

MENU > System > Setup wizard

Runs the setup wizard to guide you through setting up

the clock and network.

Inactive standby

Your R3 is set to automatically switch itself to standby

if there is no audio for more than 20 minutes. To change

this select MENU > System > Inactive standby.

Network wizard

For a guided process to help you connect to a wired or

Wi-Fi network, select MENU > System > Network >

Network wizard.

Network proﬁles

Your R3 will automatically attempt to connect to any

network it has previously connected to.

To see the list of saved networks, select MENU >

System > Network > Network proﬁle. To delete an

unwanted network, highlight it, press the CONTROL

KNOB and select YES.

Keep network connected

MENU > System > Network > Keep connected

Choose whether your R3 always remains connected to

your network, even in standby (default). We recommend

you set it to keep connected as it will ensure your R3

is always accessible using Spotify or DLNA music

streaming. We also recommend this if you have set your

clock to update from Network.

System information

Shows details of your R3 including the software version,

and unique radio ID code.

Advanced network settings

There are other advanced network settings for

experienced users for manual conguration or diagnosing

and xing network problems.

For more information visit

www.ruarkaudio.com/support.

FM radio

When listening to FM, your R3 displays the station name

and other RDS/RBDS* programme information when

available.

*Radio Data System/Radio Broadcast Data System

Change station

Press or to automatically tune to the next

available FM station. If RDS/RBDS is unavailable the

frequency is displayed instead.

Scan setting

You can change the scan setting to only stop at stations

with a strong signal by selecting Menu > Scan setting >

Strong stations only.

Programme information

Choose from radio text, programme type, frequency,

signal strength and date by selecting MENU > Info.

Manual tune

Select MENU > Manual tune then either rotate the

CONTROL KNOB or press or to change the

frequency.

Save preset

You can store 10 FM stations in your preset list. The

station name will be stored only when RDS/RBDS is

available. See ‘Common functions’ section.

Recall preset

See ‘Common functions’ section.

Mono

As an FM signal becomes weaker, the level of hiss will

increase. To reduce this, select Menu > Mono.

To further reduce hiss on weaker FM stations,

we recommend turning 3D sound OFF

EN

DAB radio

When listening to DAB/DAB+, your R3 displays the

station name and other DLS* programme information

when available.

The rst time you use your R3, or if the station list is

empty, it will automatically perform a full scan to identify

available stations.

*Dynamic Label Segment

Change station

Press or to tune to the next/previous station.

Station list

To view a list of available DAB stations select MENU >

Station list or press or . Highlight the station you

wish to listen to and press SELECT.

Programme information

Choose from radio text, programme type, signal

strength, signal format and date by selecting MENU >

Info.

Save preset

You can store 10 DAB stations in your preset list. See

‘Common functions’ section.

Recall preset

See ‘Common functions’ section.

Station order

The DAB station list can be ordered by Alphanumeric,

Ensemble or Valid. Alphanumeric puts the stations

in alphabetical order, Ensemble groups stations from

the same broadcaster together, Valid shows available

stations rst and places invalid stations (marked with ‘?’)

last.

To change station order, select Menu > Station order

and select Alphanumeric (default), Ensemble or Valid.

Invalid stations have ‘?’ in front of the station name

Station scan

If the station list is empty the radio will automatically

perform a full scan as soon as you switch to DAB.

In any case, we recommend you do a full scan from time

to time to update the station list because:

● New stations sometimes become available

● Stations close or may no longer be received

● Reception was poor during the original scan (for

example the aerial wasn’t properly tted)

● You move the radio to a different region

To do a full scan, select MENU > Scan.

Remove weak or invalid stations

Weak (burbling) or invalid stations have ‘?’ in front of the

station name and can be removed by selecting MENU >

Prune invalid.

Internet radio

Your R3 can play thousands of internet radio stations

and podcasts from all over the world (internet connection

required).

Main menu

The rst time you listen to internet radio you will see the

main menu for this mode.

If you have listened to internet radio stations on your R3

before, it will automatically play the last listened station.

Last listened

To access a list of recently listened to stations select

MENU > Last listened.

When you use your R3 for the rst time, the list will be

empty.

Station list

You can browse or search the extensive list of stations

by selecting MENU > Station list and selecting from the

various options, including genre, location and popularity.

Now playing information

The station name is shown along with additional

information like artist and track name. To change what

is displayed select MENU > Info and choose from radio

text, genre, signal quality, track name, location, and date.

EN

Search for a station

Search for a station by selecting MENU > Station list >

Stations > Search stations and then entering the name

of the station you’re looking for.

Podcasts

Many stations will have associated podcasts which

you can browse and search for just like internet radio

stations.

Mute

Press to mute and press again to resume listening.

Save a preset

You can store 10 Internet radio stations in your preset list.

See ‘Common functions’ section.

Recall a preset

See ‘Common functions’ section.

DLNA media streaming

You can also stream audio to your R3 from a Digital

Living Network Alliance (DLNA) compatible media

server. This is where you browse for music on the server

itself and play it through your R3. There are many apps

available for Mac, iOS, Linux, Android, Windows phone,

etc that will turn your smartphone, tablet or laptop into a

DLNA media server.

With DLNA media streaming, your R3 functions as a

Digital Media Renderer (DMR) so you browse for music

on your smartphone or laptop and then stream it to your

R3 over your network.

Your R3 will automatically change to DMR mode when

you select your R3 as your chosen player – DMR is not a

mode that can be selected using the SOURCE key.

Similarly, all the Now playing information will be

controlled by the server so there are no settings you can

change.

For more details refer to the documentation for your

device or app or visit www.ruarkaudio.com/support.

DLNA media streaming requires that your R3 is connected

to your network so we recommend that you set it to keep

network connected. See system settings section.

EN

Bluetooth

Your R3 supports aptX for CD quality streaming. It will

automatically connect to your bluetooth device using the

highest quality connection supported by your device.

Pairing your Bluetooth device

When you have changed the source to Bluetooth, wait

until Awaiting connection... is shown and the indicator

light on top ashes.

Use the Bluetooth setup on your smart device to pair and

connect it to your R3. It will appear in the list of paired

devices as Ruark R3. When connected, BT Connected +

your device name (eg Ozzie’s phone) is displayed.

If you do not connect within a few minutes, your R3 will

stop attempting to connect and show No connection. To

connect, select MENU > Connect device.

Connecting your Bluetooth device

As soon as you switch to Bluetooth, your R3 will display

Connecting as it attempts to connect to the last device it

was paired with.

If that device isn’t available, it displays Awaiting

connection... To connect to your R3, ensure the

Bluetooth function on your device is on and select Ruark

R3 from the paired devices list on your Bluetooth device.

Play audio

Once connected, audio from your Bluetooth device

will play through your R3. For more information on

playing audio from your Bluetooth device, refer to your

device’s documentation.

NOTE: you may need to select your Ruark R3 or

Bluetooth as your audio output on your device.

Pause track

Press and then press again to play.

Skip track

Press or to skip to the next or previous track

Adjust volume

We recommend that you adjust the volume on your

Bluetooth device so that the playback volume is about

the same as other sources. You can then use the volume

control on your R3 to adjust overall playback volume.

Now Playing information

Artist, album and track name will show if your Bluetooth

device and app support Bluetooth metadata. You can

also show the name of the connected device. Select

what is shown from MENU > Info.

ページが読み込まれています...

Ruark Audio R3 Compact Music System ユーザーマニュアル

Ruark Audio R3 Compact Music System ユーザーマニュアル

他の言語で

その他のドキュメント