Yamaha YPP-100 取扱説明書

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING: Do not place this product in a position where anyone could

walk on, trip over ,or roll anything over power or connecting cords of any

kind. The use of an extension cord is not recommended! If you must use

an extension cord, the minimum wire size for a 25' cord (or less ) is 18

AWG. NOTE: The smaller the AWG number ,the larger the current

handling capacity. For longer extension cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to update

existing units.

This product, either alone or in combination with an amplifier and head-

phones or speaker/s, may be capable of producing sound levels that

could cause permanent hearing loss. DO NOT operate for long periods

of time at a high volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should consult

an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory mounting

fixtures that are either supplied with the product or as optional accesso-

ries. Some of these items are designed to be dealer assembled or

installed. Please make sure that benches are stable and any optional

fixtures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your

dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately five years. When replacement becomes

necessary, contact a qualified service representative to perform the

replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery

being charged.

When installing batteries, do not mix batteries with new, or with batter-

ies of a different type. Batteries MUST be installed correctly. Mis-

matches or incorrect installation may result in overheating and battery

case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all

batteries away from children. Dispose of used batteries promptly and

as regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some

reason its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of prod-

ucts that contain lead, batteries, plastics, etc. If your dealer is unable

to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION

PLEASE KEEP THIS MANUAL

92-BP (bottom)

YPP-100

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference harmful

to the operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the an-

tenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service Divi-

sion, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

(class B)

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) sá länge som

den ar ansluten till vägguttaget, även om själva apparaten har

stängts av.

ADVARSEL: Netspæendingen til dette apparat er IKKE afbrudt,

sálæenge netledningen siddr i en stikkontakt, som er t endt — ogsá

selvom der or slukket pá apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita

koko laitetta verkosta.

(standby)

(3)-7

1/2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Use the speciﬁed adaptor (PA-5D, PA-5C or an equivalent recommended by

Yamaha) only. Using the wrong adaptor can result in damage to the instrument

or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Do not place the AC adaptor cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy objects

on it, or place it in a position where anyone could walk on, trip over, or roll

anything over it.

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the instrument, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power switch,

disconnect the adaptor plug from the outlet, and have the instrument inspected

by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord.

• Unplug the AC power adaptor when not using the instrument, or during

electrical storms.

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disﬁguration or damage to the internal

components.

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio

may generate noise.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• Before moving the instrument, remove all connected adaptor and other cables.

• Use only the stand speciﬁed for the instrument. When attaching the stand, use

the provided screws only. Failure to do so could cause damage to the internal

components or result in the instrument falling over.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor Location

YPP-100

(3)-7

2/2

YPP-100

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all

components, set all volume levels to minimum. Also, be sure to set the volumes

of all components at their minimum levels and gradually raise the volume

controls while playing the instrument to set the desired listening level.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning ﬂuids, or chemical-impregnated wiping cloths.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel

or keyboard. If this happens, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected by qualiﬁed

Yamaha service personnel.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not operate the instrument for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

Saving and backing up your data

• Internal data is retained for about 1 week after the power is turned off. If the

period is exceeded, the data will be lost. Be sure to turn the power switch on for

a few minutes at least once a week. The data could be lost due to malfunction or

incorrect operation. Save important data to external media such as the Yamaha

MDF3 MIDI data ﬁler.

Backing up the ﬂoppy disk

• To protect against data loss through media damage, we recommend that you

save your important data onto two ﬂoppy disks.

Connections

Maintenance

Handling caution

Saving data

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

Even when the power switch is in the “STANDBY” position, electricity is still ﬂowing to the instrument at the minimum level. When you are not using the instrument for a long

time, make sure you unplug the AC power adaptor from the wall AC outlet.

●

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use

others' copyrights. Such copyrighted materials include, without limitation, all computer software, styles ﬁles, MIDI ﬁles, WAVE data and sound

recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of

* The illustrations and LED displays as shown in this owner’s manual are for instructional purposes only, and may be different from the ones on your instru-

ment.

YPP-100

Introduction

Thank you for choosing a Yamaha Light Piano YPP-100. Your YPP-100 is a fine musical instrument that

employs advanced Yamaha music technology. With the proper care, your YPP-100 will give you many years

of musical pleasure.

● The YPP-100 utilizes Yamaha’s “AWM Stereo Sampling” tone generating Light Piano

technology to produce musically rich voices of unmatched sonic realism. The piano voices

are created with newly recorded samples taken from a full concert grand piano.

● Dual mode allows 2 voices to be played simultaneously.

● Metronome feature with variable tempo facilitates practice.

● 2-track digital recorder lets you record and play back anything you play on the keyboard.

● MIDI compatibility and a range of MIDI functions make the YPP-100 useful in a range of

advanced MIDI music systems.

In order to make the most of your YPP-100’s performance potential and features,

we urge you to read this Owner’s Manual thoroughly, and keep it in a safe place for

later reference.

■ Trademarks

• Apple and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

All other trademarks are the property of their respective holders.

Included Accessories

● Owner’s Manual

● Music Rest

● FC5 Footswitch (x1)

● Keyboard Stand

YPP-100

Contents

The Control Panel ............................................................... 8

Setting Up ......................................................................... 10

■

Power supply connections .................................. 10

■

Accessory Jacks................................................... 10

■

Music Rest ............................................................. 11

Selecting & Playing Voices .............................................. 12

Playing the Demonstration Tunes ................................... 13

■

Voice Demo............................................................ 13

■

Preset Song ........................................................... 14

■

Preset Song A-B Repeat....................................... 15

■

Preset Song Part Cancel ...................................... 16

●

Synchro Start ................................................. 16

●

Soft Pedal Start/Stop...................................... 16

The Dual Mode ................................................................. 17

●

Other Dual Mode Functions ........................... 17

Reverb ............................................................................... 18

●

Adjusting Reverb Depth ................................. 18

The Effect .......................................................................... 19

●

Adjusting Effect Depth.................................... 19

Touch Sensitivity .............................................................. 20

Transposition .................................................................... 21

The Metronome & Tempo Control................................... 22

■

The Metronome ..................................................... 22

●

Metronome Time Signature ............................ 22

●

Metronome Volume Function ......................... 22

■

Tempo Control....................................................... 22

Using the User Song Recorder ........................................ 23

■

Recording .............................................................. 23

●

Changing the Initial Settings .......................... 24

●

Erasing a Single Track ................................... 24

■

Playback ................................................................ 25

●

Synchro Start ................................................. 25

●

Soft Pedal Start/Stop...................................... 25

The Function Mode ........................................................... 26

●

To Select a Function … .................................. 26

■

F1 Tuning ...............................................................27

■

F2 Scale..................................................................27

F2.1: Scale ........................................................ 27

F2.2: Base Note ................................................ 27

■

F3 Dual Mode Functions.......................................28

F3.1: Dual Balance............................................ 28

F3.2: Dual Detune ............................................. 28

F3.3: 1st Voice Octave Shift.............................. 28

F3.4: 2nd Voice Octave Shift ............................ 28

F3.5: 1st Voice Effect Depsth............................ 29

F3.6: 2nd Voice Effect Depth ............................ 29

F3.7: Reset........................................................ 29

■

F4 Soft Pedal Mode ...............................................29

■

F5 Metronome Volume ..........................................29

■

F6 Preset Song Part Cancel Volume....................29

■

F7 MIDI Functions .................................................30

F7.1: MIDI Transmit Channel Selection ............ 30

F7.2: MIDI Receive Channel Selection ............. 30

F7.3: Local Control ON/OFF ............................. 31

F7.4: Program Change ON/OFF ....................... 31

F7.5: Control Change ON/OFF ......................... 32

F7.6: MIDI Transmit Transpose......................... 32

F7.7: Panel/Status Transmit.............................. 32

F7.8: Bulk Data Dump....................................... 32

■

F8 Backup Functions ............................................33

F8.1: Voice ........................................................ 33

F8.2: MIDI ......................................................... 33

F8.3: Tuning ...................................................... 33

F8.4: Pedal........................................................ 33

Using the MIDI Functions ................................................ 34

■

What Is MIDI? ........................................................ 34

■

Connecting to a Personal Computer .................. 36

Factory Preset Recall ....................................................... 37

Troubleshooting ................................................................ 37

Options .............................................................................. 37

Voice Descriptions ............................................................38

Demo and Preset Song List .............................................39

Factory Setting List...........................................................40

MIDI Data Format...............................................................41

MIDI Implementation Chart...............................................45

Keyboard Stand Assembly...............................................46

Specifications....................................................................49

YPP-100

The Control Panel

1 [STANDBY/ON] Switch

Press the [STANDBY/ON] switch once to turn

the power ON, a second time to turn the power OFF.

When the power is initially turned ON, a voice

selector LED will light.

2 [MASTER VOLUME] Control

The [MASTER VOLUME] control adjusts the

volume (level) of sound produced by the YPP-100’s

internal stereo sound system. The [MASTER

VOLUME] control also adjusts headphone volume

when a pair of headphones is plugged into the

PHONES jack (page 11).

3 [DEMO] Button

Activates the demo playback mode in which you

can select playback of different demonstration

sequences for each of the YPP-100’s voices. See

page 13 for details.

4 [TRANSPOSE] Button

The [TRANSPOSE] button allows access to the

YPP-100’s TRANSPOSE function (to shift the pitch

of the entire keyboard up or down in semitone

intervals).

5 [FUNCTION] Button

This button accesses a range of utility functions

— including the MIDI functions — that significantly

enhance versatility and playability. See page 26 for

details.

6 METRONOME [START/STOP] Button

Turns the metronome sound on and off. The

[TEMPO/FUNCTION ▼, ▲] buttons are used to

set the tempo of the metronome sound. The [–/NO]

and [+/YES] buttons are used to change the time

signature (beat) of the metronome if used while the

METRONOME [START/STOP] button is held —

page 22.

7 [TEMPO/FUNCTION ▼, ▲] Buttons

These buttons adjust the tempo of the metronome

function as well as the playback tempo of the re-

corder function. The tempo range is from 32 to 280

beats per minute — page 22. These same buttons are

also used to select functions — page 26.

8 [–/NO], [+/YES] Buttons

These buttons select a preset song number for

playback, and are also used to adjust a range of other

parameters.

The PHONES jacks are located on the front panel, below the left end of the keyboard. (see page 11)

B0A0G0F0E0

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6

D6 E6 F6 G6

8. 8. 8.

56 7 8 9

YPP-100

The Control Panel

9 [PRESET SONG] Button

This button enters the preset song mode. While in

this mode you can use the [–/NO] and [+/YES]

buttons to select from 20 songs.

0 TRACK [1] and [2] Buttons

The YPP-100 has a 2-track recorder, and these

buttons are used to select the track(s) to be recorded

or played back. See page 23 for details.

! SONG [START/STOP] and [REC] Buttons

These buttons control the YPP-100’s user song

recorder, letting you record and play back just about

anything you play on the keyboard.

@ Voice Selectors

Simply press any of the voice selectors to select

the corresponding voice. The voice selector LED

will light to indicate which voice is currently se-

lected.

There is also a dual mode in which two voices

can be played simultaneously across the full range of

the keyboard (see page 17 for details).

# [REVERB] Button

The [REVERB] button selects a number of

digital reverb effects that you can use for extra depth

and expressive power. See page 18 for details.

$ [EFFECT] Button

This button selects a number of effects which can

give your sound greater depth and animation.

% [TOUCH] Button

The [TOUCH] button makes it easy to adjust the

touch response of the YPP-100 to match your

playing style. See page 20 for details.

^ PHONES Jacks

... See page 11 for details.

& MIDI IN/OUT Connectors

... See page 11 for details.

* PEDAL DAMPER/SOFT Jacks

... See page 11 for details.

( OUTPUT R and L/L+R Jacks

... See page 10 for details.

) DC IN 12V Jack

... See page 10 for details.

&* ( )

YPP-100

Setting Up

Stereo System

• Before connecting the YPP-100 to other electronic components, turn off the power for all compo-

nents. Before turning the power on or off for all components, set all-volume levels to minimum.

CAUTION

Power supply connections

Using An AC Power Adaptor..............................................................

The OUTPUT R and L/L+R jacks deliver the output of the YPP-100

for connection to an instrument amplifier, mixing console, PA system,

or recording equipment. If you will be connecting the YPP-100 to a

monaural sound system, use only the L/L+R jack. When a plug is

inserted into the L/L+R jack only, the left- and right-channel signals are

combined and delivered via the L/L+R jack so you don’t lose any of the

YPP-100’s sound.

CAUTION

• When the YPP-100’s OUTPUT jacks are connected to an external sound system,

first turn the YPP-100 power on, and then the power to the external amplifier/

speaker system. Reverse this order when turning the power off.

ZMake sure that the STANDBY/ON switch of the YPP-100 is set to

STANDBY.

XConnect the AC adaptor (PA-5D, PA-5C or other adaptor specifi-

cally recommended by Yamaha) to the power supply jack.

CPlug the AC adaptor into an AC outlet.

CAUTION

• Never interrupt the power supply (e.g. unplug the AC adaptor) during any

YPP-100 record operation! Doing so can result in a loss of data.

WARNING

• Use ONLY a Yamaha PA-5D or PA-5C AC Power Adaptor (or other adaptor

specifically recommended by Yamaha) to power your instrument from the AC

mains. The use of other adaptors may result in irreparable damage to both

the adaptor and the YPP-100.

• Unplug the AC Power Adaptor when not using the YPP-100, or during

electrical storms.

• Plugging or unplugging the AC power adaptor will reset the YPP-100 to the

defaults.

Accessory Jacks

Using the OUTPUT R and L/L+R Jacks ..................................

PA-5D

YPP-100

Sequenser

Setting Up

Music Rest

The YPP-100 is supplied with a music rest that can be attached to

the instrument by inserting it into the slot at the rear of the control

panel.

Using the MIDI IN and OUT Connectors ................................

The MIDI IN connector receives MIDI data from an external MIDI

device which can be used to control the YPP-100. The MIDI OUT

connector transmits MIDI data generated by the YPP-100 (e.g. note and

velocity data produced by playing the YPP-100 keyboard).

More details on MIDI are given in “MIDI Functions” on page 30.

Using the Damper Pedal

(connect a footswitch to the DAMPER Jack)..................

A footswitch connected to the DAMPER jack will basically function

in the same way as a damper pedal on an acoustic piano. When the

footswitch is pressed, notes played will have a long sustain. Releasing

the footswitch immediately stops (dampens) any sustained notes.

• Be sure that you do not press the footswitch while turning the power on. If

you do, the ON/OFF status of the footswitch will be reversed.

• If the Damper function doesn’t work, or notes are sustained even when

the footswitch is not pressed, make sure that the pedal is properly

plugged into the DAMPER Jack.

Using the Soft Pedal

(connect a footswitch to the SOFT Jack)............................

A footswitch connected to the SOFT jack reduces the volume and

slightly changes the timbre of notes played while the footswitch is

pressed. The soft pedal function will not affect notes that are already

sustaining when the footswitch is pressed.

This footswitch can also be assigned to function as a start/stop

switch with the “Soft Pedal Mode” described on page 29.

Two sets of standard stereo headphones can be plugged in here for

private practice or late-night playing. The internal speaker system is

automatically shut off when a pair of headphones is plugged into either

of the PHONES jacks.

Using the PHONES Jacks......................................................................

YPP-100

With the AC power adaptor connected, simply press the

[STANDBY/ON] switch until it locks in the ON position. When the

instrument is not in use, be sure to turn the power off. (Press the switch

again so that it pops up.)

Set the Volume...................................................................................................

Initially set the [MASTER VOLUME] control about half way

between the “MIN” and “MAX” settings. Then, when you start playing,

re-adjust the [MASTER VOLUME] control for the most comfortable

listening level.

Select a Voice......................................................................................................

Select the desired voice by pressing one of the voice selectors.

• See “Voice Descriptions” on page 38.

Play.................................................................................................................................

The YPP-100 also offers keyboard touch response, so the volume

and timbre of notes played can be controlled according to how “hard”

you play the keys. The amount of variation available depends on the

selected voice.

• Some voices do not have keyboard touch response. See “Voice Descrip-

tions” on page 38 for details.

Add Effects As Required ........................................................................

You can add or change reverb and effects as desired by using the

[REVERB] button (page 18) and [EFFECT] button (page 19).

Selecting & Playing Voices

Turn Power On...................................................................................................

CAUTION

• Even when the switch is in the "STANDBY" position, electricity is still flowing to

the instrument at the minimum level. When you are not using the YPP-100 for a

long time, make sure you unplug the AC power adaptor from the wall AC outlet.

YPP-100

Demonstration tunes are provided that effectively demonstrate each of the

YPP-100’s voices. There are also 20 preset songs that you can play individually,

all in sequence, or in random order. Here’s how you can select and play the

demo tunes.

• The demo or preset song mode cannot be engaged while a user song recorder (page 23) is in

use.

• No MIDI reception occurs in the demo/preset song mode.

• The demo/preset song data is not transmitted via the MIDI connectors.

* See page 39 for a complete listing of the demo tunes and preset songs.

Engage the Demo Mode ..........................................................................

Play a Voice Demo.........................................................................................

Press one of the voice selectors to start playback of all songs starting

from the corresponding voice demo tune — featuring the voice nor-

mally selected by that voice selector button. (If you press the SONG

[START/STOP] button instead of a voice selector button, the PIANO 1

demo tune will begin playback.) The indicator of the selected voice

selector button will flash during playback, and “- - -” will appear on the

LED display. You can start playback of any other voice demo tune

during playback by simply pressing the corresponding voice selector.

You can stop playback at any time by pressing the SONG [START/

STOP] button or the voice selector of the currently playing demo.

• Use the [MASTER VOLUME] control to adjust the volume.

Press the [DEMO] button to engage the demo mode — the voice

selector indicators will flash in sequence.

Voice Demo

Exit From the Demo Mode ....................................................................

Press the [DEMO] button to exit from the demo mode and return to

the normal play mode.

Playing the Demonstration Tunes

YPP-100

Playing the Demonstration Tunes

Engage the Preset Song Mode ........................................................

Play a Preset Song........................................................................................

To play any of the 20 preset songs provided, use the [–/NO], [+/YES]

buttons to select the number of the tune you want to play (the number will

appear on the LED display), then press the SONG [START/STOP] button.

Playback will stop automatically when playback of the selected preset song

has finished.

Select “ALL” instead of a number to play all preset songs in sequence, or

select “rnd” to continuously play all preset songs in random order. Press

the SONG [START/STOP] button to stop playback.

• Use the [MASTER VOLUME] control to adjust the volume.

• You can use the [TEMPO/FUNCTION

▼

▲

] buttons to adjust the

playback tempo as required. This produces a relative tempo variation,

with a range from “-50” through “- - -” to “50” at maximum; the range will

differ depending on the selected song.

• The default tempo “- - -” is automatically selected whenever a new preset

song is selected, or playback of a new preset song begins during “

ALL

”

or “

rnd

” playback.

• You can play the keyboard along with the preset song playback. The

voice playing on the keyboard can be changed.

• You can change the Reverb type that is applied to the voice you play on

the keyboard and for the preset song playback. You can change the

Effect type and Touch sensitivity that is applied to the voice you play on

the keyboard. When a new preset song is selected or a new preset song

is automatically started in continuous play, the HALL 1 reverb type will

automatically be selected.

Press the [PRESET SONG] button to engage the preset song mode

— the [PRESET SONG], TRACK [1] and [2] indicators will light.

Preset Song

Exit From the Preset Song Mode...................................................

Press the [PRESET SONG] button to exit from the preset song mode,

the indicator will go off, and return to the normal play mode.

YPP-100

Preset Song A-B Repeat

The A-B Repeat function can be used to continuously repeat a

specified phrase within a preset song. Combined with the Part Cancel

function described below, this provides an excellent way to practice

difficult phrases.

Specify the Beginning (A) of the Phrase...............................

Select and play a preset song, then press the [FUNCTION] button

at the beginning of the phrase you want to repeat. This sets the “A”

point (“A-” will appear on the display).

To set the “A” point at the very beginning of the song, press the

[FUNCTION] button before starting playback.

Specify the End (B) of the Phrase ................................................

Press the [FUNCTION] button a second time at the end of the

phrase. This sets the “B” point (“A-b” will appear on the display). At

this point repeat playback will begin between the specified A and B

points. The metronome will sound when playback begins to give you a

tempo reference. However, if playback repeats from the beginning of

the song, there will be no tempo reference from metronome.

To set the B point at the song’s end, press the [FUNCTION] button

after song playback is complete and before “A- ” disappears from the

display.

Stop Playback.....................................................................................................

Press the SONG [START/STOP] button to stop playback while

retaining the specified A and B points. A-B repeat playback will resume

if the SONG [START/STOP] button is then pressed again.

To cancel the A and B points press the [FUNCTION] button once.

• The A and B points are automatically canceled when a new song is

selected.

• The A-B Repeat function cannot be used during “

ALL

” or “

rnd

” play-

back.

Playing the Demonstration Tunes

YPP-100

Preset Song Part Cancel

The 20 preset songs have separate left- and right-hand parts that can

be turned on and off as required so you can practice the corresponding

part on the keyboard. The right-hand part is played by TRACK [1]

track, and the left-hand part is played by TRACK [2] track.

Turn the Desired Part Off .......................................................................

Press the TRACK [1] or [2] button to turn the corresponding part off

— the corresponding indicator will go out (these buttons alternately

toggle the corresponding part on and off).

• The parts can be turned on or off even during playback.

• The Preset Song Part Cancel function cannot be used during “

ALL

” or

“

rnd

” playback.

• The “Preset Song Part Cancel Volume” function described on page 29

can be used to set the canceled part so that it plays at a volume from “0”

(no sound) to “20”. The default setting is “5”.

• Both parts are automatically turned ON whenever a new song is selected.

Start/Stop Playback......................................................................................

Press the SONG [START/STOP] button to start and stop playback

as required.

Synchro Start ......................................................................................................

When the Synchro Start function is engaged, playback of the se-

lected preset song will begin automatically as soon as you start playing

on the keyboard.

To engage the Synchro Start function press the SONG [START/

STOP] button while holding the part button corresponding to the part

which is ON. A dot will appear in the lower right corner of the display.

(Repeat the previous operation to disengage the Syncro Start function.)

Playback will then start as soon as you begin playing on the key-

board.

• If you hold a track button which is OFF while pressing the SONG [START/

STOP] button, that track will be turned ON and the Synchro Start mode

will be engaged.

Soft Pedal Start/Stop ..................................................................................

A footswitch connected to the SOFT jack can be used to start and

stop playback of a preset song using the “Soft Pedal Mode” function

described on page 29.

Playing the Demonstration Tunes

YPP-100

The Dual Mode

The dual mode makes it possible to play two voices simultaneously across

the entire range of the keyboard.

To activate the dual mode simply press two voice selectors at the

same time (or press one voice selector while holding another). The

voice indicators of both selected voices will light when the dual mode is

active. To return to the normal single-voice play mode, press any single

voice selector.

According to the voice numbering priority as shown in the diagram

on the left, lower valued voice numbers will be designated as the 1st

Voice (the other voice will be designated as the 2nd Voice).

• [EFFECT] in the Dual Mode

Depending upon the conditions one effect type will take priority over the

other. Depth will be decided according to the depth default value of the

voice combination. However, using function F3 (see page 28) you can

change the depth value for each voice as you like.

Effect depth setting via the panel controls (i.e. pressing the [–/NO] or

[+/YES] buttons while holding the [EFFECT] button — see page 19) will

be applied to the 1st Voice only.

• [REVERB] in the Dual Mode

The reverb type assigned to the 1st Voice will take priority over the other.

(If the reverb is set to OFF, the 2nd Voice’s reverb type will be in affect.)

Reverb depth setting via the panel controls (i.e. pressing the [–/NO] or

[+/YES] buttons while holding the [REVERB] button — see page 18) will

be applied to the 1st Voice only.

Other Dual Mode Functions................................................................

The YPP-100 Function mode provides access to a number of other

dual-mode functions, listed below. See the corresponding pages for

details.

• Dual Balance................................................. 28

• Dual Detune .................................................. 28

• 1st Voice Octave Shift ................................... 28

• 2nd Voice Octave Shift.................................. 28

• 1st Voice Effect Depth ................................... 29

• 2nd Voice Effect Depth.................................. 29

• Reset............................................................. 29

Voice numbering priority

YPP-100

Reverb

To select a reverb type press the [REVERB] button a few times until

the indicator corresponding to the desired type lights (the indicators

light in sequence each time the [REVERB] button is pressed). No

reverb is produced when all indicators are off.

OFF

No reverb effect is selected when no REVERB indicator is lit.

ROOM

This setting add a continuous reverb effect to the sound that is similar

to the type of acoustic reverberation you would hear in a room.

HALL 1

For a “bigger” reverb sound, use the HALL 1 setting. This effect

simulates the natural reverberation of a small-size concert hall.

HALL 2

For a really spacious reverb sound, use the HALL 2 setting. This effect

simulates the natural reverberation of a large concert hall.

STAGE

A simulation of the type of reverb produced in a stage environment.

• The default reverb type (including OFF) and depth settings are different

for each voice.

Adjusting Reverb Depth..........................................................................

Adjust the reverb depth for the selected voice by using the [–/NO]

and [+/YES] buttons while holding the [REVERB] button. The depth

range is from 0 through 20 (the current depth setting appears on the

LED display while the [REVERB] button is held). A setting of “0”

produces no effect, while a setting of “20” produces maximum reverb

depth. Press the [–/NO] and [+/YES] buttons simultaneously while

holding the [REVERB] button to recall the default setting for the

current voice (default depth settings are different for each voice).

The [REVERB] button selects a number of digital reverb effects that you can

use for extra depth and expressive power.

YPP-100

The Effect

The [EFFECT] button allows you to select one of the effects that can give

your sound greater depth and animation.

To select an effect type press the [EFFECT] button a few times until

the indicator corresponding to the desired type lights (the indicators

light in sequence each time the [EFFECT] button is pressed). No effect

is produced when all indicators are off.

OFF

No effect is selected when no EFFECT indicator is lit.

CHORUS

Shimmering, broadening effect

PHASER

Adds depth to the sound.

TREMOLO

Tremolo effect

DELAY

Echo effect

• The default effect type (including OFF) and depth settings are different for

each voice.

Adjusting Effect Depth..............................................................................

Effect depth can be individually adjusted for the selected voice by

using the [–/NO] and [+/YES] buttons while holding the [EFFECT]

button. The depth range is from 0 through 20 (the current depth setting

appears on the LED display while the [EFFECT] button is held). A

setting of “0” produces no effect, while a setting of “20” produces

maximum effect depth. Press the [–/NO] and [+/YES] buttons simulta-

neously while holding the [EFFECT] button to recall the default

setting for the current voice (the default depth settings are different for

each voice).

YPP-100

Touch Sensitivity

Four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT

or FIXED — can be selected to match different playing styles and preferences.

To select a touch sensitivity type press the [TOUCH] button a few

times until the indicator corresponding to the desired type lights (the

indicators light in sequence each time the [TOUCH] button is pressed).

HARD

The HARD setting requires the keys to be played quite hard to

produce maximum loudness.

MEDIUM

The MEDIUM setting produces a fairly “standard” keyboard response.

This is the initial factory default setting.

SOFT

The SOFT setting allows maximum loudness to be produced with

relatively light key pressure.

FIXED (no indicator lit)

All notes are produced at the same volume no matter how hard the

keyboard is played.

When the FIXED type is selected, the volume of notes played in the

FIXED mode can be set by using the [–/NO] and [+/YES] buttons

while the [TOUCH] button is held (the current volume level appears on

the display). The volume range is from 1 through 127. The default

setting is 80.

• This setting does not change the weight of the keyboard.

• The touch sensitivity type and volume set in the FIXED mode will become

the common setting for all voices. However, the touch sensitivity settings

may have little or no effect with certain voices which are not normally

responsive to keyboard dynamics (Refer to the “Voice Descriptions” on

page 38).

ページを読み込んでいます...

Yamaha YPP-100 取扱説明書

関連論文

その他の書類