4
•
•
•
•
❑ CY-12R/C (V-Cymbal unit)
❑ Connection Cable
❑ Cable Tie
■ Owner's Manual (this manual)
❑ Wing Nut
❑ Felt Washer
❑ Stopper
Before using the CY-12R/C, you need to make the settings for the percussion
sound module (p. 2).
Contents of the Package
Names of the Components
Features
Bell Portion
Bow Portion
Edge Portion
BOW/EDGE Output Jack
BOW/BELL Output Jack
The superior design has taken into account not only the shape of the cymbal, but also the bounce of the stick, and
even the movement caused by playing. It can be used as a ride, crash, or splash cymbal.
• Similar touch and feel as with acoustic cymbals
• They're quiet!
When the CY-12R/C is used as a ride cymbal, you can play bell shots (p. 6); edge shots (p. 6) can be played when using
it as a crash cymbal.
You can also use choking techniques, whereby you stop the sound by grasping the cymbal edge with your hand (p. 7).
• Separate tones in bow and edge, or bow and bell; choking possible
• Compatible with all Roland percussion sound modules (p. 2)
• Three way triggering and positional sensing are possible
(When using the TD-10 + TDW-1 with V-Cymbal Control) (p. 6)
Owner's Manual
Thank you, and congratulations on your choice of the Roland CY-12R/C V-Cymbal.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” (p. 3–4) and
“IMPORTANT NOTES” (p. 4). These sections provide important information concerning the proper
operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every
feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be
saved and kept on hand as a convenient reference.
Copyright © 2001 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the
written permission of ROLAND CORPORATION.
02892234 ’01-10-B3-11N
2
TD-10 (
TDW-1 V-Cymbal Contro
l)
TD-10 (TDW-1)
TD-10 (Non expanded)
TD-8
(*2)
TD-6
TD-7
(*3, *4)
TD-5
SPD-20
HPD-15
(*4)
Trigger Type
RdA
Sensitivity
8
Threshold
4
Curve
Linear
Scan Time (*1)
1.0
Retrigger Cancel
(*1)
10
Mask Time (*1)
8
Xtalk Cancel (*1)
50
Mount Type (*1)
CymMount
Trigger Type
P7B
Sensitivity
8
Threshold
4
Curve
Linear
Scan Time (*1)
1.8
Retrigger Cancel
(*1)
5
Mask Time (*1)
8
Xtalk Cancel (*1)
40
Mount Type (*1)
CymMount
Trigger Type
Pd7
Sensitivity
5
Threshold
3
Curve
Linear
Scan Time (*1)
1.5
Retrigger Cancel
(*1)
5
Mask Time (*1)
8
Xtalk Cancel (*1)
40
TRIGGER TYPE
CY1/PD7
SENSITIVITY
(*1)
10
THRESHOLD
(*1)
4
CURVE
(*1)
LINEAR
SCAN TIME
(*1)
2.5
RETRIG CANCEL
(*1)
8
MASK TIME
(*1)
8
XTALK CANCEL
(*1)
50
TrigType
CY Type
Sensitivity
(*1)
10
Threshold
(*1)
4
TrigCurve
(*1)
LINEAR
Xtalk Cancel
(*1)
50
Scan Time
(*1)
2.5ms
Retrig Cancel
(*1)
8
Mask Time
(*1)
8ms
Cross Talk Group
1
Velocity Curve Norm3
Choke Off
Max Dyna 5
MIn Dyna 1
Min Velo 1
Mask Time 0
Threshold 1
Trigger Type P1
Sensitivity 8
Threshold 2
Curve Lnr
Scan Time 2.5
Retrigger Cancel 3
Mask Time 8
Crosstalk Cancel 50
Trig Sens 10
Trig Threshold 0
Trig Type Pd7
Trig Curve 0
Scan Time 2.5
Retrig Cancel 3
Mask Time 8
Crosstalk Cancel 30
Input Mode HD/RM
Trig Type PD-9
Trig Sens 10
Curve Linear
Threshold 2
Scan Time 1ms
Retrig Cancel 2
Mask Time 4ms
X-Talk Rate 40%
Recommended settings for the trigger parameters when using the CY-12R/C with various percussion
sound modules.
• Bow shots, edge shots, bell shots and choking techniques are possible with the CY-12R/C (p. 6).
• If you find it difficult to get bell shots to sound, try adjusting the “Scan Time.”
• The trigger parameters should be adjusted as necessary to match the actual state of your configuration, and the
environment in which it is being used.
Recommended Settings for the Percussion Sound Module
*1: You need to set each trigger parameter after setting the trigger type.
*2: Notice Regarding TD-8 Upgrade
As of October 2001, “CY1” has been added as a trigger type selection. Selecting “CY1” automatically sets the other trigger
parameters to the recommended values, allowing you to make the settings for the CY-12R/C simply and easily.
You can use the CY-12R/C even with previous TD-8 versions by selecting “PD7,” then manually setting the other trigger
parameters to the recommended values (as shown in the above list).
For more information about the TD-8 upgrade, consult with your retailer, the nearest Roland Service Center, or an
authorized Roland distributor, as listed on the “Information” page.
*3: Each trigger parameter can be set independently for the “head-side” and “rim-side.” Set to the same value for the head and
rim. Trigger parameters can be set individually for each patch.
*4: The TD-7 and the HPD-15 support the use of edge shots with the CY-12R/C, but they do not support choking techniques.
3
Next
USING THE UNIT SAFELY
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
................................................................................................
002a
• Do not open or perform any internal modifi-
cations on the unit.
................................................................................................
003
• Do not attempt to repair the unit, or replace
parts within it (except when this manual
provides specific instructions directing you
to do so). Refer all servicing to your retailer,
the nearest Roland Service Center, or an
authorized Roland distributor, as listed on the
“Information” page.
................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g.,
direct sunlight in an enclosed vehicle, near
a heating duct, on top of heat-generating
equipment); or are
• Damp (e.g., baths, washrooms, on wet
floors); or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
................................................................................................
005
• This unit should be used only with a rack or
stand that is recommended by Roland.
................................................................................................
006
• When using the unit with a rack or stand
recommended by Roland, the rack or stand
must be carefully placed so it is level and
sure to remain stable. If not using a rack or
stand, you still need to make sure that any
location you choose for placing the unit
provides a level surface that will properly
support the unit, and keep it from wobbling.
................................................................................................
011
• Do not allow any objects (e.g., flammable
material, coins, pins); or liquids of any kind
(water, soft drinks, etc.) to penetrate the unit.
................................................................................................
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for
the safe operation of the unit.
................................................................................................
014
• Do not drop the unit!
................................................................................................
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
4
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on page 3–4, please read and observe the
following:
Placement
354b
• Do not expose the unit to direct sunlight, place it
near devices that radiate heat, leave it inside an
enclosed vehicle, or otherwise subject it to temper-
ature extremes. Also, do not allow lighting devices
that normally are used while their light source is
very close to the unit (such as a piano light), or
powerful spotlights to shine upon the same area of
the unit for extended periods of time. Excessive
heat can deform or discolor the unit.
355
• To avoid possible breakdown, do not use the unit in
a wet area, such as an area exposed to rain or other
moisture.
356
• Do not allow rubber, vinyl, or similar materials to
remain on the unit for long periods of time. Such
objects can discolor or otherwise harmfully affect
the finish.
357
• Do not put anything that contains water (e.g.,
flower vases) on the unit. Also, avoid the use of
insecticides, perfumes, alcohol, nail polish, spray
cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft cloth.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry
cloth or one that has been slightly dampened with
water. To remove stubborn dirt, use a cloth impreg-
nated with a mild, non-abrasive detergent. After-
wards, be sure to wipe the unit thoroughly with a
soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of
any kind, to avoid the possibility of discoloration
and/or deformation.
Additional Precautions
553
• Use a reasonable amount of care when using its
jacks and connectors. Rough handling can lead to
malfunctions.
556
• When connecting / disconnecting all cables, grasp
the connector itself—never pull on the cable. This
way you will avoid causing shorts, or damage to
the cable’s internal elements.
558d
• This instrument is designed to minimize the extra-
neous sounds produced when it’s played. However,
since sound vibrations can be transmitted through
floors and walls to a greater degree than expected,
take care not to allow these sounds to become a
nuisance to neighbors, especially when performing
at night and when using headphones.
559a
• When you need to transport the unit, package it in
the box (including padding) that it came in, if
possible. Otherwise, you will need to use equivalent
packaging materials.
562
• Use a provided cable or a cable from Roland to make
the connection. If using some other make of
connection cable, please note the following precau-
tions.
• Some connection cables contain resistors. Do not
use cables that incorporate resistors for
connecting to this unit. The use of such cables can
cause the sound level to be extremely low, or
impossible to hear. For information on cable
specifications, contact the manufacturer of the
cable.
104
• Try to prevent cords and cables from
becoming entangled. Also, all cords and
cables should be placed so they are out of the
reach of children.
................................................................................................
106
• Never climb on top of, nor place heavy
objects on the unit.
................................................................................................
118
• Should you remove wing nut, washers, or
stopper bolt, make sure to put them in a safe
place out of children's reach, so there is no
chance of them being swallowed accidentally.
................................................................................................
5
Attaching to a Stand
Attach the CY-12R/C with the optional cymbal mount (MDY
series), or drum stand cymbal mount (MDS series).
1. Use a commercially available drum key to
tighten the stopper bolt.
The stopper keeps the CY-12R/C from turning, and
prevents the cables from catching or getting tangled on the
stand.
fig.01.e
2. Attach the CY-12R/C so the unit is oriented as
shown in the diagram (bolt should be opposite
the output jacks).
3. Tighten the wing nut to obtain the desired
movement.
Use the included felt washer and the wing nut.
fig.02.e
• Double sounding may occur if the wing nut is loose.
• Do not use the washer or felt included with the cymbal
mount (MDY series).
Connecting to
a Percussion Sound Module
(TD-6, TD-8, TD-10, etc.)
About the Output Jacks
The CY-12R/C features two different output jacks, BOW/BELL
and BOW/EDGE.
Use the BOW/BELL output jack when you want to play the
bow and the bell sounds; use the BOW/EDGE output jack
when you want to play the bow and the edge sounds.
Use either the BOW/BELL or BOW/EGDE output jack, but
not both at the same time (except for the TD-10 + TDW-1 with
V-Cymbal Control).
Connecting both jacks results in two separate trigger inputs
playing simultaneously.
If you are using the TD-10 + TDW-1 with V-Cymbal Control,
you can use both the BOW/BELL and BOW/EGDE output
jacks at the same time (Three Way Triggering). For more
details, refer to “If Using TD-10 + TDW-1 with V-Cymbal
Control” (p. 6).
Making the Connections
To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the power
on all devices before making any connections.
1.
Use the included cable to connect one of the CY-
12R/C’s output jacks (either one, but not both,
EXCEPT when using with the TD-10 + TDW-1
with V-Cymbal Control installed) to the drum
sound module’s trigger input jack.
Connect the L-shaped plug of the included cable to the
CY-12R/C. This will prevent strain from being applied to
the CY-12R/C.
To make use of edge shot and choking play techniques,
you'll need to connect to a trigger input jack on the
percussion sound module that accommodates rim shots.
The TD-8's “1/2 (KICK 1/2)” and “11/12 (AUX 1/2)” do
not support rim shots.
2. Secure the cable with cable ties.
Leave enough slack so that the cable is not pulled by any
shaking or vibration of the cymbal when it is struck.
fig.CY03.e
Take care to ensure that the cable does not come into
contact with the cymbal or stand. Contact between the
cable and the cymbal or stand can result in problems,
Stopper
(Be sure to
orient it correctly)
Tighten the bolt with
a commercially available
drum key
Wing Nut
Felt Washer
Output Jack Corresponding Play
Methods
Tones
Sounded
BOW/BELL Bow Shot (p. 6) Head
Bell Shot (p. 6) Rim
Choke (p. 7) –
BOW/EDGE Bow Shot (p. 6) Head
Edge Shot (p. 6) Rim
Choke (p. 7) –
Tighten it
not to slip
Wind the cable
tie twice
Secure the cable in place
with the cable tie
Leave some
slack in
the cable
Turn back
to fix the
cable
Next
6
such as double sounding.
3. Make the trigger settings for the percussion
sound module. For the recommended values,
refer to p. 2.
Should you neglect to make the appropriate settings for the
percussion sound module.
• Sometimes it does not sound (uneven volume)
• The volume is too low (reduced sensitivity)
• Double sounding may occur
For information on how to change the parameters for a
percussion sound module, refer to its owner’s manual.
If Using TD-10 + TDW-1
with V-Cymbal Control
When you use the TD-10 + TDW-1 V-Cymbal Control, three
way triggering is possible.
* Three Way Triggering is not available with the TD-8.
About Three Way Triggering
By using two cables to connect the CY-12R/C and a TD-10, you
can then perform using three different tones: bow, bell, and edge.
TDW-1 specifications allow the Three Way Triggering
function to be used with only one V-Cymbal. For example, if
you use the Three Way Triggering function with one CY-15R,
you would not be able to use Three Way Triggering if you
added another CY-12R/C.
Connections/Examples of Settings
If you connect a pad or a V-Cymbal ONLY to the trigger input
for which trigger type is set to the “CTR”(11/AUX 1), it will
not work.
Correspondences Between Playing
Methods and Trigger Input
* Head-side tones for the trigger input 11/AUX 1 cannot be sounded.
For more details on the settings for Three Way Triggering,
refer to the TDW-1 with V-Cymbal Control Owner's Manual.
The TDW-1 with V-Cymbal Control Owner's Manual contains
an explanation of how the CY-15R is used with Three Way
Triggering. Substitute “CY-12R/C” for “CY-15R” as you read
through the text.
Playing Methods
Bow Shot
This is the most common playing method, playing the pad face
of the cymbal. It corresponds to the sound of the “head-side” of
the connected trigger input.
Edge Shot
This playing method involves striking the edge with the
shoulder of the stick. It corresponds to the sound of the “rim-
side” of the connected trigger input.
To make use of edge shot, you'll need to connect to a trigger
input jack on the percussion sound module that
accommodates rim shots.
Bell Shot
This playing method involves striking the bell. It corresponds
to the sound of the “rim-side” of the connected trigger input.
• To make use of bell shot, you'll need to connect to a
trigger input jack on the percussion sound module that
accommodates rim shots.
• Use the shoulder of the stick when playing bell shots.
CY-12R/C
Output
TD-10 Trigger
Input
TD-10 Trigger
Type
BOW/BELL 10/RIDE RdA
BOW/EDGE 11/AUX1 CTR
Playing Methods TD-10 Trigger Input
Bow Shot 10/RIDE Head
Bell Shot 10/RIDE Rim
Edge Shot 11/AUX 1 Rim
Bow
Edge sensor
Bell
Next
7
Choking
Choking (pinching) the cymbal’s edge with the hand
immediately after hitting the cymbal makes the sound stop.
To make use of choking play techniques, you’ll need to
connect to a trigger input jack on the percussion sound
module that accommodates rim shots.
fig.CY07.e
Troubleshooting
Issues Affecting The Overall System
Check these first
• Is the trigger type set correctly?
Make the trigger parameter settings for your percussion
sound module (p. 2).
• Is a monaural cable being used?
When a monaural cable is used, the sound does not
change when an edge shot or a bell shot is made. Choke
play is not possible, either.
Use stereo cable.
The sound does not change when an edge
shot is made
• Is the cable connected to the BOW/EDGE output?
Make the connection to the BOW/EDGE output to enable
the CY-12R/C to support edge shots (p. 5).
• Are you striking the cymbal in the area with the edge
sensors?
Edge sensors are embedded only in the part of the CY-
12R/C directly in front (p. 6).
The sound does not change when a bell shot
is made
• Is the cable connected to the BOW/BELL output?
Make the connection to the BOW/BELL output to enable
the CY-12R/C to support bell shots (p. 5).
• Use the shoulder of the stick when playing bell shots
(p. 6).
• Adjust the “Scan Time.”
Choke play is not possible
• Are you choking the cymbal in the area with the edge
sensors?
Edge sensors are embedded only in the part of the CY-
12R/C directly in front (p. 7).
Ride cymbal sounds odd
(Other cymbal sound is heard simultaneously)
• If using a sound module other than the TD-10 furnished
with the TDW-1 with V-Cymbal Control, connect either
the CY-12R/C’s BOW/BELL output or the BOW/EDGE
output (p. 5).
Double sounding
• Are any cables touching the CY-12R/C?
Secure the cables in place with the cable ties so that they
do not touch the units. Also, be careful to make sure that
the cables are not pulled by the movement of a cymbal
when struck (p. 5).
• Are the stopper, felt washer, and wing nut attached
correctly?
Double triggering may occur if the stopper and/or wing
nut is loose. Use a tuning key (drum key) to tighten
properly.
* If double triggering still occurs, try adjusting trigger
parameters, such as Retrigger Cancel, on the sound module you
are using (TD-6, TD-8, TD-10, etc.)
The volume level is too low
• If the cymbal is struck while power to the drum module
(such as the TD-6, TD-8, or TD-10) is turned on, the
response to light hits will be poor. Do not strike pads or
cymbals while turning on the power.
When using the TD-10 + TDW-1 with V-
Cymbal Control
No sound is heard
• Is the trigger type set to “CTR”?
Tones from inputs for which the trigger type is set to
“CTR” do not sound (p. 6).
The sound does not vary when the striking
position changes
• The CY-12R/C is capable of the positional detection
feature. Positional detection is possible when
plugged into the specified input on a Roland sound
module with this feature.
• For more on tones that can change according to the
part of the cymbal struck, refer to the tone list in the
Owner's Manual that came with your drum module.
• With trigger types “RdB” and “CrB,” positional
sensing is not possible. Use “RdA” or “CrA.”
Specifications
CY-12R/C: V-Cymbal Ride/Crash
Pad Size: 12 inches
Trigger: 3 (Bow/Bell/Edge)
Dimensions: 300 (W) x 300 (D) x 51 (H)
11-13/16 (W) x 11-13/16 (W) x 2-1/16 (H)
Weight: 1.1 kg
2 lbs 7 oz
Accessories: Owner’s Manual, Connection Cable,
Wing Nut, Felt Washer, Stopper, Cable Tie
Options: Cymbal Mount (MDY-10U)
Stand (MDS-6, MDS-8, MDS-10)
* In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
Edge sensor
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as
shown below.
As of May 15, 2001 (Roland)
ARGENTINA
Instrumentos Musicales S.A.
Florida 656 2nd Floor
Office Number 206A
Buenos Aires
ARGENTINA, CP1005
TEL: (54-11) 4- 393-6057
BRAZIL
Roland Brasil Ltda
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CANADA
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (0604) 270 6626
Roland Canada Music Ltd.
(Toronto Office)
Unit 2, 109 Woodbine Downs
Blvd, Etobicoke, ON
M9W 6Y1 CANADA
TEL: (0416) 213 9707
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.
MEXICO
TEL: (525) 668 04 80
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City,
REP. DE PANAMA
TEL: (507) 315-0101
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
VENEZUELA
Musicland Digital C.A.
Av. Francisco de Miranda,
Centro Parque de Cristal, Nivel
C2 Local 20 Caracas
VENEZUELA
TEL: (02) 285 9218
AUSTRALIA
Roland Corporation
Australia Pty., Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
TEL: (02) 9982 8266
NEW ZEALAND
Roland Corporation Ltd.
32 Shaddock Street, Mount Eden,
Auckland, NEW ZEALAND
TEL: (09) 3098 715
HONG KONG
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
TEL: 2415 0911
CHINA
Beijing Xinghai Musical
Instruments Co., Ltd.
6 Huangmuchang Chao Yang
District, Beijing, CHINA
TEL: (010) 6774 7491
Shanghai Xingtong Acoustics
Equipment CO.,Ltd.
Rm.1108, No.2240 Pudong South
Road Shanghai, CHINA
TEL: (021) 6873 4123
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
TEL: (022) 498 3079
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
MALAYSIA
BENTLEY MUSIC SDN BHD
140 & 142, Jalan Bukit Bintang
55100 Kuala Lumpur,MALAYSIA
TEL: (03) 2144-3333
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
SINGAPORE
Swee Lee Company
150 Sims Drive,
SINGAPORE 387381
TEL: 846-3676
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung Shan
N.Road Sec.2, Taipei, TAIWAN,
R.O.C.
TEL: (02) 2561 3339
THAILAND
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi 2,
Bangkok 10100, THAILAND
TEL: (02) 2248821
BAHRAIN
Moon Stores
Bab Al Bahrain Road,
P.O. Box 20077
State of BAHRAIN
TEL: 211 005
VIETNAM
Saigon Music
138 Tran Quang Khai St.,
District 1
Ho Chi Minh City
VIETNAM
TEL: (08) 844-4068
JORDAN
AMMAN Trading Agency
Prince Mohammed St. P.O. Box
825 Amman 11118 JORDAN
TEL: (06) 4641200
KUWAIT
Easa Husain Al-Yousifi
Abdullah Salem Street,
Safat KUWAIT
TEL: 5719499
LEBANON
A. Chahine & Fils
P.O. Box 16-5857 Gergi Zeidan St.
Chahine Building, Achrafieh
Beirut, LEBANON
TEL: (01) 335799
QATAR
Al Emadi Co. (Badie Studio
& Stores)
P.O. Box 62,
DOHA QATAR
TEL: 4423-554
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary Bldg.,
1st Floor
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SYRIA
Technical Light & Sound
Center
Khaled Ibn Al Walid St.
P.O. Box 13520
Damascus - SYRIA
TEL: (011) 2235 384
TURKEY
Barkat muzik aletleri ithalat
ve ihracat Ltd Sti
Siraselviler cad.Guney is hani 84-
86/6, Taksim. Istanbul. TURKEY
TEL: (0212) 2499324
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor DUBAI
U.A.E.
TEL: (04) 3360715
EGYPT
Al Fanny Trading Office
P.O. Box 2904,
El Horrieh Heliopolos, Cairo,
EGYPT
TEL: (02) 4185531
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: 28 29 16
SOUTH AFRICA
That Other Music Shop
(PTY) Ltd.
11 Melle St., Braamfontein,
Johannesbourg
Republic of SOUTH AFRICA
P.O.Box 32918, Braamfontein 2017
Republic of SOUTH AFRICA
TEL: (011) 403 4105
Paul Bothner (PTY) Ltd.
17 Werdmuller Centre Claremont
7700
Republic of SOUTH AFRICA
P.O. Box 23032
Claremont, Cape Town
SOUTH AFRICA, 7735
TEL: (021) 674 4030
CYPRUS
Radex Sound Equipment Ltd.
17 Diagorou St., P.O. Box 2046,
Nicosia CYPRUS
TEL: (02) 453 426
DENMARK
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: (039)16 6200
FRANCE
Roland France SA
4, Rue Paul Henri SPAAK,
Parc de l'Esplanade, F 77 462 St.
Thibault, Lagny Cedex FRANCE
TEL: 01 600 73 500
FINLAND
Roland Scandinavia As,
Filial Finland
Lauttasaarentie 54 B
Fin-00201 Helsinki, FINLAND
TEL: (9) 682 4020
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: (040) 52 60090
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
26422 Patras, GREECE
TEL: 061-435400
HUNGARY
Intermusica Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint, HUNGARY
TEL: (23) 511011
IRELAND
Roland Ireland
Audio House, Belmont Court,
Donnybrook, Dublin 4.
Republic of IRELAND
TEL: (01) 2603501
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
NORWAY
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 273 0074
POLAND
P. P. H. Brzostowicz
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
PORTUGAL
Tecnologias Musica e Audio,
Roland Portugal, S.A.
Cais Das Pedras, 8/9-1 Dto
4050-465 PORTO
PORTUGAL
TEL: (022) 608 00 60
RUSSIA
MuTek
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: 095 169 5043
SPAIN
Roland Electronics
de España, S. A.
Calle Bolivia 239, 08020
Barcelona, SPAIN
TEL: (93) 308 1000
SWITZERLAND
Roland (Switzerland) AG
Musitronic AG
Gerberstrasse 5, Postfach,
CH-4410 Liestal, SWITZERLAND
TEL: (061) 921 1615
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (08) 702 0020
UKRAINE
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo, UKRAINE
TEL: (03131) 414-40
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 700139
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
AUSTRIA
Roland Austria GES.M.B.H.
Siemensstrasse 4, P.O. Box 74,
A-6063 RUM, AUSTRIA
TEL: (0512) 26 44 260
BELGIUM/HOLLAND/
LUXEMBOURG
Roland Benelux N. V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
AFRICA
CHILE
Comercial Fancy ΙΙ S.A.
Avenida Rancagua #0330
Providencia Santiago, CHILE
TEL: 56-2-373-9100
URUGUAY
Todo Musica S.A.
Cuareim 1844, Montevideo,
URUGUAY, CP11200
TEL: 5982-924-2335
EUROPE
AUSTRALIA/
NEW ZEALAND
ASIA
CENTRAL/LATIN
AMERICA
NORTH AMERICA
MIDDLE EAST
AFRICA
EL SALVADOR
OMNI MUSIC
75 Avenida Notre YY Alameda,
Juan Pablo 2, No. 4010
San Salvador, EL SALVADOR
TEL: (503) 262-0788
ROMANIA
FBS LINES
Piata Libertatii 1,
RO-4200 Gheorghehi
TEL: (066) 164-609
PARAGUAY
Distribuidora De
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Edeficio, El Dorado Planta Baja
Asuncion PARAGUAY
TEL: 595-21-492147
PERU
VIDEO Broadcast S.A.
Portinari 199 (ESQ. HALS),
San Borja, Lima 41,
REP. OF PERU
TEL: 51-14-758226
COSTA RICA
JUAN Bansbach
Instrumentos Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: (506)258-0211
CRISTOFORI MUSIC PTE
LTD
Blk 3014, Bedok Industrial Park E,
#02-2148, SINGAPORE 489980
TEL: 243 9555
IRAN
MOCO, INC.
No.41 Nike St.Dr.Shariyati Ave.
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: 285 4169
ISRAEL
Halilit P. Greenspoon &
Sons Ltd.
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
