Instruction Manual
I/O Module
LZ80-K1/ LZ80-K2
2020.7
Printed in Japan
©2019 Magnescale Co., Ltd.
LZ80-K1/LZ80-K2
2-A02-723-0B
45 Suzukawa, Isehara-shi, Kanagawa 259-1146, Japan
For foreign customers
Note: is product (or technology) may be restricted by the government in your country. Please make sure
that end-use, end user and country of destination of this product do not violate your local government
regulation.
8. Dimensions
/ Unit : mm
[For U.S.A. and Canada]
THIS CLASS A DIGITAL DEVICE COMPLIES WITH PART15 OF
THE FCC RULES AND THE CANADIAN ICES-003. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND
Read all the instructions in the manual carefully before use and strictly
follow them.
Keep the manual for future references.
Safety Precautions
Magnescale Co., Ltd. products are designed in full consideration of safety.
However, improper handling during operation or installation is dangerous
and may lead to re, electric shock or other accidents resulting in serious
injury or death. In addition, these actions may also worsen machine
performance.
erefore, be sure to observe the following safety precautions in order to
prevent these types of accidents, and to read these “Safety Precautions”
before operating, installing, maintaining, inspecting, repairing or otherwise
working on this unit.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDERSIGNED OPERATION.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A
EST CONFORME À LA NORME NMB-003 DU CANADA.
Warning Indication Meanings
e following indications are used throughout this manual, and their
contents should be understood before reading the text.
Symbols requiring attention Symbols prohibiting actions
CAUTION DO NOT DISASSEMBLE
Warning Failing to follow the precaution items given below
may lead to severe injury or death.
• Do not open the cover of the LZ80-K1/LZ80-K2 to disassemble or
modify the unit, as this may result in burns or injury.
ese actions may also damage the internal circuitry.
Caution Failing to follow the precaution items given below
may lead to injury or damage to surrounding
objects.
• e unit does not have an explosion-proof structure.
erefore, do not use the unit in an atmosphere charged with
in ammable gases as this may result in re.
• Be sure to turn o the power before connecting or disconnecting
power and signal connectors in order to prevent damage or
misoperation.
General precautions
• Before and during operations, be sure to check that our products
function properly.
• Provide adequate safety measures to prevent damages in case our
products should develop malfunctions.
• Use outside indicated speci cations or purposes and modi cation of our
products will void any warranty of the functions and performance as
speci ed of our products.
• When using our products in combination with other equipment,
the functions and performances as noted in this manual may not be
attained, depending on operating and environmental conditions.
Termination module
1. Overview
is product is an I/O module that uses external signals to perform
operations within the composition units and to output data. It is
used in combination with a main module and counter modules.
is module has eight inputs and eight outputs, and the function of
each pin is set by the display unit.
During operation, also refer to the display unit and main module
Instruction Manuals.
Input and output signals that can be set by the display
unit
Input signals
Counter address, comparator group, measurement mode, reset,
reference point load, etc.
Output signals that can be set
Comparator output, reference point monitor, alarm, etc.
2. Name and Function of Each Part
POWER lamp
Lights green when the power is on.
Output connector
is is the output signal connector.
Input connector
is is the input signal connector.
Module connector
Connects an I/O module or termination module.
3. Number of Units that can be Connected within
the Unit and Connection Position
Up to two LZ80-K modules can be connected within the unit.
Always connect the LZ80-K modules in the endmost position of the
composition units, then connect a termination module (supplied
with the main module).
/ Pin assignment for input
/
No.
/
Name
/
Description
1IN1 1 / Input 1
2IN2 2 / Input 2
3IN3 3 / Input 3
4IN4 4 / Input 4
5IN5 5 / Input 5
6IN6 6 / Input 6
7IN7 7 / Input 7
8IN8 8 / Input 8
9I-COM /
Input common
/ Pin assignment for output
/
No.
/
Name
/
Description
1OUT1 1 / Output 1
2OUT 2 2 / Output 2
3OUT 3 3 / Output 3
4OUT 4 4 / Output 4
5OUT 5 5 / Output 5
6OUT 6 6 / Output 6
7OUT 7 7 / Output 7
8OUT 8 8 / Output 8
9O-COM /
Output common
567 984321
For I/O connector output
For I/O connector input
Sink/source input
t *OQVUFRVJWBMFOUDJSDVJUDPNNPOUP-;,,
0/WPMUBHF 7PSNPSF
0''WPMUBHF7PSMFTT
Sink output Source output
t 0VUQVUFRVJWBMFOUDJSDVJU
.BYJNVNMPBEWPMUBHF%$7
.BYJNVNMPBEDVSSFOU%$N"
4. Connector Pin Assignment
e LZ80-K1/K2 have eight dedicated input pins and eight dedicated
output pins.
e I/O pin functions are set by the display unit.
LZ80-K1 : Current sink type
LZ80-K1 : Current source type
5. Cable Connections
e connectors are push-in types. To disconnect a cable, hold down
the orange button and pull out the cable.
Use 0.14 to 0.55 mm2 (AWG20 to 26) single wire or twisted wire
cables for the cables connected to the connectors.
Connector (supplied with the I/O module): FK-MC 0,5/9-ST-2,5
made by Phoenix Contact
6. I/O Circuit
7. Spe ci cations
Model name LZ80-K1 / LZ80-K2
Supply voltage DC 10.8 to 26.4 V (supplied from
MG80-MA)
Power consumption 2.0 W
I/O 9-pin connector ×2,
photocoupler-insulated, 8
inputs, 8 outputs
LZ80-K1 : Current sink type
LZ80-K2 : Current source type
Indicator lamp Power supply : Green LED ×1
Operating temperature/
humidity range
0 to + 50 °C (No condensation)
Storage temperature/humidity
range
–20 to + 60 °C (20 to 90% RH)
Mass 130 g
Mounting method DIN rail
/
