SDE-259 / SDE-260
Ver 1.01
SET-259 / SET-260
Land Nest Dome Small / Medium
SDE-259 / SDE-260
Land Nest Dome Medium
Land Nest Dome Small
Product Manual : Ver 1.01
SET-259 / SET-260
Land Nest Small / Medium
Tent & Tarp Set (Tent)
Thank you for purchasing a Snow Peak product. This product is a tent for camping. For safety, read the
following instruction manual before use. Please keep it safe for future reference. Finally, if you find
anything that you do not understand in the description or any problems with the product, please stop use
immediately and contact the retailer or Snow Peak Customer Service.
Set Contents
Name of the Parts
Fly×1
Inner Tent×1
Center Pole×1
A Pole×2
C pole×2
Carry Bag×1Peg Case×1 Pole Case×1
Instruction manual Duralumin Pin Pegs
21cm(8.25')×14
Rope with Rope Tensioner
Land Nest Dome Small
2.5m(8' 2") x 6
Land Nest Dome Medium
3m(9’8”)×6
Ventilation
Peg down loop
C pole
Plastic hook
Center sleeve
Door panel
Peg down loop
A pole C pole
Plastic hook
Center pole Sleeve
Safety Precautions Before use please read thoroughly to ensure safety and to avoid accidents.
Misuse could easily result in a serious accident or death.DANGER
The tent material is not flame-proof. Do not use combustion-based heat sources such as
lanterns, stoves or heaters, or open flames such as matches, candles, lighters or cigarettes,in-
side the tent. The use of such heat or light sources inside a small, enclosed space is very
dangerous and may result in fire, oxygen deficiency or carbon monoxide poisoning.
Do not keep fuel, or flammable items for replenishing the fuel, inside the tent.
Pay close attention to the weather. If extreme weather is in the forecast, pack up camp and evacuate
to a safe place.
Do not bring heated items into the tent when they are at high temperatures. Inside the tent, very high
temperatures may cause heatstroke. Pay close attention to the temperature, particularly when
children are asleep inside the tent.
Choose a flat, well-drained area with firm ground to pitch the tent. Choose an area where there is no
chance of avalanches, landslides, wind gusts or sudden flooding.
Before using the product, check each part for abnormalities. If there are abnormalities, take the
product to the dealer or Snow Peak Customer Service for inspection or repair.
This product is not intended to be in permanent use.
Sunlight can cause the surface of the Fly to heat up, potentially causing low-temperature burns.
Do not assemble or use the tent close to a bonfire, fireworks, etc. Flying sparks can create holes in the
tent fabric.
Firmly hold the tent/tarp pole when assembling and disassembling the tent/tarp. Unexpected accidents
may occur due to the Pole ends recoiling, etc., so ensure that the surroundings are safe, with no other
people in the vicinity.
Firmly secure the Pegs, Guy Lines, etc.
If the tent is left in the sun for long periods, the materials may fade in color or the fabric may deteriorate
and lose strength. Do not leave the tent set up permanently.
Misuse could result in serious injury or death.WARNING
Misuse could result in injury to the user and/or damage to property.CAUTION
A combination of Polyester fabric is used for this product. Taking the material characteristics into consideration, we
adopted processing and color patterns that will result in less color migration. However, depending on storage
conditions, slight color migration may occur. Do not store the product while it is wet.
Before storing, the product should be cleaned and dried sufficiently. If the product is stored when wet, the build-up
of mold, bad odors, color migration and material deterioration will occur. Dry the product sufficiently in a breezy
and shaded area and clean the surface with a soft brush before storing.
*Do not flip the tent over with poles still in the sleeves, as the poles may break, and cloth damage may occur.
Clean and dry the surface of the poles before storing. If stored when wet, corrosion may occur, resulting in strength
deterioration. Keep the joints clean and apply a small amount of silicone lubricant, applying an excessive amount
of lubricant will stain the cloth. Ensure that the cords inside the poles are not pulled unnecessarily.
Store the product in a well-ventilated area, away from heat and moisture.
Using the zipper when it is covered with mud, sand or dust may cause wear or damage.
Clean the zipper with a brush before use. Apply small amounts of silicone lubricant to the zipper regularly to ensure
smooth movement. Do not apply excessive amounts of lubricant as it will leave stains on the cloth.
Minor damage to the cloth can be mended with repair tape that can be purchased from your local outdoor gear
retailer. Refer to the product instructions for the correct use of such repair tape.
Depending on the conditions during use, the tent material may deteriorate over a wide area, losing its durability
and becoming irreparable.
To maximize the longevity of this product, regularly check and maintain the product (including all accessories such
as the pegs).
Maintenance & Storage
Land Nest
Building tape(×2)
Door panel
(Entrance/Exit)
Door panel
(Entrance/Exit)
Triangular window
Center pole(with black section)
A pole
Connect without leaving gaps at the joints.
Extend center pole and A pole x 2 and connect them firmly.
*Make sure to connect them without leaving gaps at the joints.
Check the point (refer to " Name of the Parts)") and insert the center pole into the center sleeve.
Spread the fly on a flat area.
First, check the direction of the two door panels for the entrance and exit.
Make sure that both buckles of the building tape are connected. If they are disconnected, be sure to
connect them before setting up the tent. The triangular window should be facing upwind.
Follow the instructions below to set up and disassemble. Practice set up before camping and check to ensure
all the accessories are functioning. Excessive setup and tear down may damage the body or poles, potentially
resulting in an accident. Please read this manual carefully before use.
Instructions for Use
Back side
Make sure to match
the black colors of the sleeve and the pole.
Center sleeve
There is a gap
No gap
Connect the A pole to one side of the center pole.
Make sure the tip of the center pole is fully inserted into the A pole.
Insert the tip of the A pole into the grommet on the fly side (two locations).
Insert the other side of A pole into the center frame as shown in step .
While bending the center pole as shown in the figure below, insert one end of the A pole into the
grommet on the fly side.
Fly
Grommet
on the fly side
Grommet on the fly side
While slowly raising the entire pole, pull the grommet toward you.
Insert the other end of the A pole into the grommet on the fly side.
Extend both C poles and connect the sections firmly.
*Make sure to connect them without leaving gaps at the joints.
Check the [B] point (refer to " Name of the Parts)") and insert the C pole into the sleeve.
Pull the grommet towards you while raising the pole.
*At this time, Make sure that the black section fits inside the
sleeve. Please do this while checking the overall balance.
The same color as the fly.
Connect without leaving gaps at the joints.
After inserting the C pole into the sleeve, insert the tip of the C pole into the outer grommet.
Insert the other end of the C pole in the same manner.
Insert the other C pole into the center frame, in the same manner as step .
Hook the plastic hooks on the fly onto the each of the poles.
Insert the duralumin pegs through the peg down loops on the hem and then insert the pegs.
*Please drive the pegs all the way into the ground.
*If the peg is driven in too hard, it may bend, break, or otherwise be damaged. If the peg hits an obstacle
such as a stone, change the location of the peg before hammering it in.
*If you peg down the door without closing the zipper, you may not be able to close the door after the tent
is set up.
Outer grommet
Fly
Hammer the pegs
down diagonally.
Hammer the peg down vertically
to secure the tent.
Ring Ring
Ring Ring
Hammer the peg
down diagonally.
Hammer the pegs
down diagonally.
Hammer the peg down vertically
to secure the tent.
Hammer the peg
down diagonally.
Gently pull each corner loop in the order shown below and peg down without any slack.
View from top
Stretch each rope and drive in the pegs.
How to attach the rope
How to attach the rope with ring
Drive the peg into the
ground at 45°angle.
Wrap the tape around the pole,
thread between the tapes next to
the seam and pull.
Sewn
seam
Pole
Ring
Rope tensioner
View from top
Pull the rope tensioner on the rope to apply tension.
Be careful not to pull the rope too much. If you pull too hard, the fly may be damaged.
Connect the A pole to one side of the center pole.
Make sure the tip of the center pole is fully inserted into the A pole.
Velcro back
Bar
Peg down tapePeg down tape
Tape with hook
Hook the plastic hooks of the inner tent onto the plastic rings inside the fly.
Check the front and back of the inner tent and spread it out inside the room.
The side with logo at the bottom should face inside the room.
*There is no front/back setting on the Fly itself.
Logo
Attach each corner of the bottom according to the diagram below.
Hook the tapes with hooks on
both sides of the bottom to the
rings on the inside of the fly hem.
Hook the peg-down tapes
at the two rear locations to the pegs that hold the fly.
Hook the tape with hooks (with adjusters) attached to the
bottom corners onto the rings on the inside of the fly hem.
Inner bottom
How to install the inner tent
Q: What can be done if a pole is broken while the tent is in use?
A: For an emergency treatment, use a repair pipe or splint, and secure with vinyl tape. Or fully disassemble
the tent for repair.
Q: What can be done if the tent/tarp cloth is damaged or rips while the tent is in use?
A: Seal the area with packing tape on both sides or use a tent repair kit that can be purchased from your local
outdoor gear retailer. When using a repair kit, read the instructions carefully.
Q: What can be done when the water-repellent finish degrades?
A: The water-repellent finish will lose its effectiveness with repeated use. When the material’s water
repellence decreases, please use a water-repellent spray that can be purchased from your local outdoor
gear retailer. When using such sprays, please follow the product’s instructions.
Q: What can be done if mold develops on the tent material?
A: Wipe the affected area with a dry cloth and sterilize with alcohol. When the material has a color change
due to mold, this color change cannot be removed. Removing mold with excessive force may result in
further deterioration of the material and the coating finish.
Mist is a collection of water droplets suspended in the air that turns into condensation in rapidly falling tempera-
tures. In smaller spaces such as the inside of a tent or shelter, water vapor concentration is higher than in an
ordinary room and frequently results in more condensation. Depending on the surrounding conditions, it may be
impossible to avoid condensation completely, even with waterproof materials. To reduce condensation, allow
steady ventilation while the tent is in use.
Regarding Condensation
A combination of polyester fabric is used in this product. Both materials are treated with a high-quality,wa-
ter-repellent finish. However, the level of water-repellent capacity and durability may vary slightly due to the
characteristics of each material.
The water-repellent finish will lose effectiveness after repeated use. When the water repellence decreas-
es,please use a water-repellent spray purchased from your local outdoor gear retailer. When using such
sprays, please follow the product’s instructions.
Materials with high waterproof capacity are used in this product. However, if the materials are in contact with
pools of water on the ground for long periods, the water may be absorbed into the material, potentially
resulting in discoloration.
Water-Repellent and Waterproof Functions
A UV protection treatment has been applied to the fly material. The UV protection treatment will lessen the
permeation of ultraviolet rays, which are harmful to humans, and slow the deterioration of the fly.
*The UV protection treatment does not completely shield humans from ultraviolet rays or stop the deterioration
of the material’s strength.
When the tent material is exposed to sunlight for long periods, color degradation or strength deterioration
may occur. Do not leave the product assembled permanently.
If the material deteriorates due to ultraviolet rays and is badly damaged, it may become irreparable.
Regarding the Effect of Ultraviolet Rays
FAQ
Precautions for Disassembly and Storage
Please make sure that the product is sufficiently dry before storing it.
If the wind is strong, wait for it to subside before disassembling the shelter.
If you have attached an inner room, be sure to remove the inner room or any other products from the shelter
before disassembling it.
Please ensure nothing is inside the shelter and that all panels and windows are closed.
Please ensure that all belts are connected before taking down the shelter. Connecting the belts makes it
easier to peg down the shelter next time.
Please fold the main poles from the center each time. If you fold the main poles from the edges, the shock
cord inside the pole may stretch or break, causing the frame to bend or break.
Remove all pegs, clean them, and store them in the peg case with their heads facing down. Store all frames
in the frame case. The frame should be stored with its head facing down in the frame case. If the frame is
exposed, it may damage the fabric or the carry bag.
450cm(14.8’)
265cm(8.7’)
265cm(8.7’)
280cm(9.2’)
170cm(5.6’)
160cm(5.2’)
375cm(12.3’)
225cm(7.4’)
225cm(7.4’)
250cm(8.2’)
130cm(4.3’)
140cm(4.6’)
Snow Peak, Inc.
456, Nakanohara, Sanjo-Shi, Niigata 955-0147 Japan
Tel. +81 256-46-5858 / Fax. +81 256-46-5860
www.snowpeak.co.jp
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1 (503) 461-0781 / Instagram. @snowpeakusa
Email. [email protected] / www.snowpeak.com
Spec
●Capacity: 2 persons
Capacity: 3-4 persons
Small size
Material: Fly/75D Polyester Taffeta, PU coating, Waterproof
rating: 1,800mm minimum, water-repellent finish, UV protection
treatment, Inner Wall/68D Polyester Taffeta, Bottom/210D
Polyester Oxford, PU coating, Waterproof rating: 1,800mm
minimum; Pole /A6061 (13mm (0.51"))
Carry Bag Size 65×20×25(h)cm (25.6”x7.9”x9.8”)
Weight 7.2kg (15.8 lbs.)
Medium size
Material: Fly/75D Polyester Taffeta, PU coating, Waterproof
rating: 1,800mm minimum, water-repellent finish, UV protection
treatment, Inner Wall/68D Polyester Taffeta, Bottom/210D
Polyester Oxford, PU coating, Waterproof rating: 1,800mm
minimum; Pole /A6061 (Ф13mm (0.51"))
Carry Bag Size 70×21×25(h)cm (27.6”x8.3””x9.8”)
Weight 8.7kg (19.2 lbs.)
Snow Peak has taken all possible measures to ensure every product is durable and functions correctly. If you find
any product defects, please contact the retailer where you purchased the product or Snow Peak Customer Service.
If there are apparent defects in the product's manufacturing, the defective product will be repaired or exchanged free
of charge. In other cases, Snow Peak will repair the product for an appropriate fee. The decision to repair or replace
the product will be at our discretion. Snow Peak will not repair the product for any damage that occurred due to the
following:1.Material deterioration caused by age. / 2.Damage caused by modifications or rough handling. / 3.Dam-
age caused by inappropriate use not mentioned in the instruction manual. / 4.Damage caused by unexpected
accidents. / 5. Any damage other than defects in the manufacturing process. / 6.Damage caused by dust or rust. / 7.
Damage and defects caused by dismantling the product. / 8.Damage and defects caused by dropping, jolting or
other shocks. / 9. Deterioration or failure of parts due to friction. / 10. Damage caused by the use of the product in
combination with another manufacturer's products.
If professional repairs are required, please contact the retailer where you purchased the product or Snow
Peak Customer Service.
When you request repairs, please make sure that the product is dry and clean.
Please attach a memo or a tag indicating the necessary repair and please write details of how and when the
damage occurred.
Transportation and repair costs are determined as follows.
1. Within warranty: The transportation cost (both ways) and repaircost will be covered by Snow Peak.
2. Outside warranty: The transportation cost (both ways) and repaircost will be covered by the customer.
Warranty
Repair
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
