290cm(9.5')
235cm(7.7')
205cm(6.7')
205cm(6.7')
170cm(5.6')
This set consists of an inner room, ground sheet, and walkway that creates a bedroom
for 3 people in Zekka. It can be attached to either the left or right side of ZeKKa.
Front and back doors and side mesh windows ensure excellent ventilation.
*This product is specifically designed for TP-710 Zekka. It cannot be used with other shelters or alone.
Zekka Inner Room
TP-710IR
Ver 1.00
Thank you for purchasing this Snow Peak Product. This product is an Inner Room specifically designed for Zekka.
In order to ensure your safety when using this product, please read these instructions carefully before use. Please
be sure to keep this document for future reference. Although this product is expected to be complete and safe,
please check all accessory items and practice assembling and handling it in a safe location prior to use in the field.
If you find anything in the instruction manual that is difficult to understand, or if you find a defect with the product, stop
using it immediately and contact the dealers where you purchased the product or Snow Peak Customer Service.
Instruction Manual : Ver 1.00
Inner room
Ground sheet
Walkway
Storage case
Hook
Peg down
loop
Door panel
Hook
Tape
with hook
Specifications
Part names
●Contents: Inner room, ground sheet (with walkway), storage case
●Materials: Inner room (walls)/68D polyester taffeta; Inner room (bottom)/210D polyester oxford, PU coating,
waterproof rating 1,800 mm minimum; Ground sheet/210D polyester oxford, PU coating, waterproof rating
1,800 mm minimum
●Storage case size: 32x13×52(h)cm(12.6"×5.1"×20.5")
●Weight: 4kg(8.8lbs)
Before Use: Please read thoroughly to ensure safety and avoid accidents.
DANGER / Misuse could easily result in a serious accident or death.
WARNING / Misuse could result in serious injury or death to the user.
CAUTION / Misuse could result in injury to the user and/or damage to property.
●Sunlight can cause the surface of the inner room to heat up, potentially causing low-temperature burns.
●Do not assemble or use close to a bonfire, fireworks, etc. Flying sparks can create holes in the fabric.
●Firmly hold the inner room when assembling and disassembling.
●Firmly secure the pegs and tensioners.
●When the inner room material is exposed to sunlight for long periods, color degradation or strength deterio-
ration may occur. Do not leave the product assembled permanently.
●Pay close attention to the weather. If extreme weather is in the forecast, pack up camp and
evacuate to a safe place.
●Do not bring heated items into the tent when they are at high temperatures. The temperature inside
the inner room will be high during warm weather, and there is a risk of heatstroke. Pay close
attention to the temperature, particularly when children are asleep inside the shelter.
●Choose a flat, well-drained area with firm ground to pitch the tent. Choose a place with no chance
of avalanches, landslides, wind gusts, or sudden flooding.
●The material of this inner room is not flameproof. Do not use combustion-based heat sources such
as lanterns, stoves, or heaters, or open flames such as matches, candles, lighters, or cigarettes
near or inside the inner room. The use of such heat or light sources inside a small enclosed space
is hazardous and may result in fire.
●Do not keep fuel, or flammable items for replenishing the fuel inside the inner room.
Instruction Manual
(This Manual)
Attaching the inner room
The ground sheet and inner room can be attached to either the left or right side of the Zekka shelter.
In this manual, we describe attachment on the right side.
Spread the ground sheet so that the PU coated surface (shiny surface) is facing up and the woven name tag
is on the indoor side.
Spread the inner room so that the
part where the logo is printed is in
front.
Logo
Indoor side
Attach the hook to the O-ring of the shelter (fly).
Stretch the rubber loops at each corner of the ground sheet and attach them to the corresponding pegs.(4
locations)
Attach all three hooks at the back of the top of the
inner room to the O-rings of the shelter (fly).
Attach each of the three S-hooks at the top of
the inner room to the specified O-rings as
shown in the figure. After attaching, adjust the
length of the tape and apply tension.
Attach the hooks and rubber loops at the bottom corners of the inner room to the O-rings and pegs of the
shelter (fly).
Finally, peg down the peg down tape at the bottom of the entrance. This peg down reduces the bottom lift
when opening and closing the door, making it easier to open and close. (Separately purchase the pegs
that are used here.)
Inner bottom
Attach the tapes with hooks at the
bottom entrance corners of the
inner room to the tent frame O-rings
of the shelter (fly).
Attach the tapes with
hooks at the bottom
entrance corners of
the inner room to the
tent frame O-rings of
the shelter (fly).
Tent frame
Cross frame
Indoor side
Tent frame
O-ring
Tape with
hook
Peg down
loop (gray)
Attach the two peg
down tapes at the
back to the pegs that
fasten the shelter (fly).
Peg down tape
Tent frame
Tape with
hook
Peg down
loop (gray)
Tent frame
O-ring
Attach the toggles on the
walkway to the O-rings on
the indoor side and center of
the ground sheet.
Spread the walkway so that
the PU coated surface
(shiny surface) is facing up
and the woven name tag is
on the indoor side.
Attach the toggles on the
walkway to the O-rings on
the indoor side and back
side of the ground sheet.
Inner bottom
Indoor side
●Before storage, the product should be cleaned and dried sufficiently. If the product is stored when wet, the
build-up of mold, bad odors, color migration, and material deterioration will occur. Dry the product sufficiently
in a breezy and shaded area and clean the surface with a soft brush before storing.
●Please store in a well-ventilated area away from direct sunlight, high temperatures, and humidity.
●Using the zipper when it is covered with mud, sand or dust may cause wear or damage. Clean the zipper with
a brush before use. Apply small amounts of silicone lubricant to the zipper regularly to ensure smooth
movement. Applying an excessive amount of lubricant will stain the fabric.
●Small areas of fabric damage can be fixed with repair tape.
Please read the repair tape manual carefully before applying.
●Depending on the conditions during use, the tent material may deteriorate over a wide area, losing its durabili-
ty and becoming irreparable.
●In preparation for the next use, regularly check and maintain the product, including accessories such as
tension ropes.
Maintenance
To attach the walkway
Spread the walkway so that the PU coated surface (shiny surface) is facing up and the woven name tag is on
the indoor side.
Attach the toggles on the walkway to the O-rings on the indoor side and center of the ground sheet.
Attach the toggles on the walkway to the O-rings on the indoor side and back side of the ground sheet.
Attach to the ground sheet at the other side in the same manner.
The specifications of Snow Peak products are based on field testing and quality control to ensure the correct
function and longevity of every product. If apparent defects in the manufacturing of the product are found, the
defective product will be repaired or exchanged free of charge. Damages, as follows, are not covered under
warranty.
1. Material deterioration caused by age. / 2. Damage caused by modifications or rough handling. / 3. Damage
caused by improper use not following the instruction manual. / 4. Damage caused by unexpected accidents. /
5. Damage not caused by defects in the manufacturing process. / 6. Damage caused by dust or rust. / 7.
Damage or defects caused when dismantling the product. / 8. Damage and defects caused by dropping or other
shocks to the product. / 9. Deterioration or failure of parts due to friction. / 10. Damage caused by the use of the
product in combination with other maker’s products.
Warranty
●For repairs, please contact the retailer where you purchased the product or Snow Peak user service.
●When you ask for repair, please make sure that the product is dry and clean.
●Please attach a memo or some kind of tag indicating the needed repair, and please write details of when and
how the damage occurred.
●Shipping cost and repair fee for the repair as follows.
1. Within warranty: Return shipping cost and repair fee will be covered by Snow Peak
2. Outside warranty: Return shipping cost and repair fee will be covered by the user.
Repair
0120-010-660
Email:[email protected]
Snow Peak, Inc.
456, Nakanohara, Sanjo-Shi, Niigata 955-0147 Japan
Tel. +81 256-46-5858 / Fax. +81 256-46-5860
www.snowpeak.co.jp
Snow Peak USA, Inc.
404 NW 23rd Avenue, Portland, Oregon 97210, USA
Tel. +1-503-697-3330 / Instagram. @snowpeakusa
Email. [email protected] / www.snowpeak.com
/
