Stanley STEL503 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
ENGLISH 3
7
STEL501
STEL503
2
C
BA
D
*Your model may be a 1 mode unit (STEL501) & as
such does not have drilling mode selector (4) on
unit see figure D.
* The picture above may differ slightly to actual unit.
STEL501
11
期代碼位置
3
ENGLISH
Intended use
Your Stanley SDS plus rotary hammer has been designed for
drilling in wood, metal, plastics, and masonry as well as for
light chiselling applications.
Safety instructions
General power tool safety warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions listed below may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future
reference. The term "power tool" in all of the warnings
listed below refers to your mains operated (corded) power tool
or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
Hammer STEL501 STEL503
Power input W 720 720
No-load speed /min 0-980 0-980
Impact rate BPM 0-5200 0-5200
Impact energy J 2.0 2.0
Modes 1 3
Max capacity mm
- Concrete 22 22
- Steel - 13
-Wood - 30
Weight kg 3.0 3.0
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools.
Unmodied plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the inuence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying
power tools with your nger on the switch or energising
power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
STEL501/503
HAMMER
Technical data
4
ENGLISH
the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate for
which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualied
repair person using only identical
replacement parts.
This will ensure that the safety of
the power tool is maintained.
Additional power tool safety warnings
u Wear ear protectors. Exposure to noise can cause
hearing loss.
u Use auxiliary handles supplied with the tool.
Loss of control can cause personal injur.
u Hold power tool by insulated gripping sur-
faces when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord.Cutting ac-cessory contact-
ing a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
u Never use a chisel accessory in rotary mode. The acces-
sory will bind in the material and rotate the drill.
u Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the work
by hand or against your body leaves it unstable and may
lead to loss of control.
u Before drilling into walls, oors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u Injuries caused by prolonged use of a tool. When using
5
ENGLISH
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Label on tool
The following symbols are shown on the tool:
:
WARNING! To reduce the risk of injury,
the user must read the instruction manual.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service Centre in
order to avoid a hazard.
Using an extension cable
If an extension cable is requred, use an approved extension
cable suitable for the power input of this tool (see technical
data). The minimum conductor size is 1.5 mm
2
.
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch (only for STEL503)
4. Mode selector (only for STEL503)
5. Tool holder
6. Side handle
7. Depth stop
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle (g.C)
u Turn the grip counterclockwise until you can slide the side
handle (6) onto the front of the tool.
u Rotate the side handle into the desired position.
u Tighten the side handle by turning the grip clockwise.
Warning! Alaways use the tool with the side
handle properly assembled.
Fitting an accessory (g.A)
u Clean and grease the shank (8) of the accessory.
u Pull back the sleeve (9) and insert the shank into the tool
holder (5).
u Push the accessory down and turn it slightly until it ts into
the slots.
u Pull on the accessory to check if it is properly locked. The
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
u To remove the accessory, pull back the sleeve (9) and pull
out the accessory. tool holder.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, oors or ceilings, check
for the location of wiring and pipes.
Selecting the operating mode (g. B)
The tool can be used in three operating modes. Press in the
button (10) and rotate the drilling mode selector (4) towards
the required position, as indicated by the symbols.
Drilling
u For drilling in steel, wood and plastics, set the operating
mode selector (4) to the
b
position.modes.
Hammer Drilling
u For hammer drilling in masonry and concrete, set the
6
ENGLISH
operating mode selector (4) to the
s
position
u When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
u For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (4) to the
q
position.
u Make sure the forward/reverse switch is in the forward
position.
u When changing from hammer drilling to chiselling, turn
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage the
spindle lock.
Warning! If your hammer is a 1 mode unit (STEL501), It
only has one function - hammer drilling. It can’t select operat-
ing mode.
Selecting the direction of rotation
This function is included on only certain models (STEL503).
For drilling, and for chiselling, use forward (clockwise) rotation.
For removing a jammed drill bit, use reverse (counterclock-
wise) rotation.
u To select forward rotation, push the forward/reverse slider
(3) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Setting the drilling depth (g. C)
u Slacken the side handle (6) by turning the grip counter-
clockwise.
u Set the depth stop (7) to the desired position. The maxi-
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
u Tighten the side handle by turning the grip clockwise.
Switching on and off
u To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
u As a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
u For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only in forward (clockwise) rotation.
u To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory used.
Stanley accessories are engineered to high quality standards
and designed to enhance the performance of your tool. By us-
ing these accessories you will get the very best from your tool.
Maintenance
Your Stanley corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when tted).
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your Stanley product needs
replacement, or if it is of no further use to you, do not dispose
of it with household waste. Make this product available for
separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
7
Stanley SDS
/
1.
a.
b.
c.
2.
a.
STEL501 STEL503
720 720
/ 0-980 0-980
BPM 0-5200 0-5200
J 2.0 2.0
1 3
- 22 22
- - 13
- - 30
3.0 3.0
b.
c.
d.
e.
f.
(RCD)RCD
3.
a.
b.
c. /
d.
e.
f.
g.
4.
a.
b.
c.
/
STEL501/503
8
d.
e.
f.
g.
5.
a.
u
u
u
u
u
u
u
u
/
u
u
u /
u
u
u
u
(MDF)
:
C
11
: 2012 XX XX
u Stanley
( )
1.5
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
7.5 15 25 30 45 60
9
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
1.
2.
3. /STEL503
4. STEL503
5.
6.
7.
C
u (6)
u
u
A
u (8)
u (9)(5)
u
u
u (9)
B
(10)
(4)
u
(4)
b
u
(4)
s
u
u
(4)
q
u /
u
(STEL501)
(STEL503)
u / (3)
u /
C
u (6)
u (7)
u
u (1)
u
u (2)
u
10
Stanley
Stanley/ /
/
u /
u /
/
u
u
u / /
u
u
Stanley
02 - 29994633
2861F
90594996 06/2013
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Stanley STEL503 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で