GH50W
簡介
感謝選擇 MSI IMMERSE GH50 WIRELESS 用於驚豔音效和電競體驗的享受。
本說明書提供使用說明及圖示，幫助您認識產品，以及首次使用設定說明。
第一次於PC上使用時，系統會自行安裝驅動程式；待安裝後，建議於電競前，
重新啟動PC。
1. 麥克風靜音 / 配對鈕
2. 電源按鈕
3. 充電狀態指示燈
4. 麥克風連接埠（可拆式麥克風）
5. 音量控制
6. 充電埠 (USB Type-C)
7. 重置按鈕
8. 外接音源埠
9. 發射器配對按鈕
10. 發射器配對指示燈
外觀檢視
無線模式
• 於你的電腦上連接無線USB發射器並開啟耳機電源
• 無線USB發射器連接後，發射器指示燈亮起：
- 白色燈號恆亮：與耳機連線已配對
- 白色燈號緩慢閃爍：與耳機連線已斷開
- 白色燈號快速閃爍：耳機與發射器正在配對中
• 重置耳機與發射器的連線：以尖頭狀的物體（如別針）插入孔洞中並推觸按鈕2秒
有線模式 （3.5mm）
• 於外接音源埠連接3.5mm音源線，耳機會自動關機並轉換至有線模式
Playstation
• 於PS4或PS5上任一USB埠上，連接無線USB發射器
• 於Playstation系統中更改設定，將Output to Headphones調整為All Audio
設定
控制說明
電源按鈕
• 電源開啟：按壓並維持3秒
• 電源關閉：按壓並維持2秒
• 當耳機電源開啟後，電源按鈕會亮起：
- 白色燈號恆亮：耳機與發射器已配對
- 白色燈號閃爍：耳機與發射器配對已斷開
- 白色燈號快速閃爍：耳機进入配對模式
麥克風靜音 / 配對按鍵 Mic Mute / Paring Button
• 按壓一次靜音麥克風，則紅色燈號恆亮
• 按壓一次取消麥克風靜音，則紅色燈號熄滅
• 配對耳機與發射器：按壓並維持3秒，則電源按鈕白色燈號快速閃爍
音量控制
• 調大音量：向上滾動控制滾輪
• 調降音量：向下滾動控制滾輪
• 嗶聲響起：當音量已調整至最大或最小值
重置按鈕
• 重置耳機：以尖頭狀的物體（如別針）插入孔洞中並推觸按鈕一下，耳机复位并
进入关机
電池使用時間 & 充電說明
• 耳機充電：以USB-C線連接充電埠和另一端的電力來源
• 充電狀態指示燈號：
- 充電完成，紅色燈號恆亮
- 充電中，紅色燈號呼吸閃爍
- 電量低，紅色燈號緩慢閃爍"
重要提示
1. 充電時，最大輸入電壓為5.5V
2. 推薦使用經官方認證且標有電壓值5V和電流500mA
3. 當電力耗盡，請盡速為耳機充電
4.如長時間未使用耳機，建議於完全充滿後再行使用
5. 建議以較為溫和力道連接麥克風，避免對麥克風連接埠造成損傷
6. 請勿自行拆卸產品，避免造成損傷
Introduction
Thank you for choosing MSI IMMERSE GH50 WIRELESS to enjoy an astonishing audio
and gaming experience. This guide provides instructions and illustrations to help you get
the most from this product including the first time setup.
The first time to use the headset on a PC, the operating system will automatically install
the device driver. After the device driver loads, we recommend you reboot your PC before
gaming.
Wireless mode
• Connect the Wireless USB Transmitter to your PC, and turn on the headset.
• The Transmitter Status Indicator will illumicate when the Wireless USB
Transmitter is plugged
- The white light styas on: the headset is connected.
- The white light flashes slowly: the headset is disconnected
- The white light flashes quickly: the headset and the transmitter are pairing
• To reset the connectivity of the headset and the transmitter: insert a pointed
object such as a pin into the hole and push the button for 2 seconds
Wired mode (3.5mm)
• Connect the 3.5mm audio cable with the AUX port, the headset will automatically
power off and switch to wired mode (LINE IN).
Playstation
• Connect the wireless USB transmitter to any USB port on your PS4 or PS5
console.
• Change the settings in the PlayStation system to set “Output to Headphones”
to “All Audio”."
Setup
Power Button
• To power on: press and hold for 3 seconds
• To power off: press and hold for 2 seconds
• The Power Button will illumicate when the headset is turned on:
- The white ligth stays on: the headset is connected with the transmitter
- The white light flashes slowly: the headset is disconnected with the tranmitter
- The white light flashes quickly: the headset is pairing
Mic Mute / Paring Button
• Press to mute the microphone, the red light stays on.
• Press to unmute the microphone, the red light goes off.
• To pair the headset and the transmitter: press and hold for 3 seconds, the white light on
power button flahes quickly.
Volume Control
• To turn up the volume: scroll up the control wheel
• To turn down the volume: scroll down the control wheel
• Beep sound pops up: when them volume is adjusted to the maximum or minimum
Controls
• To Charge the headset: connect the USB-C cable to the charging port and the other
end to a power source
• Charging Status Indicator:
- When fully charged, the red light stays on
- When charging, the red light breathes
- When battery is low, the red light flashes slowly
Battery Life & Charging
1. The maximum input voltage to recharge this headset is 5.5V
2. Use of chargers labeled with 5V voltage and 500mA current purchased from official
channels is recommended.
3. When the battery is exhausted, please recharge the headset as soon as you can.
4. It is recommended to fully charge the headset if it is not in use for a long time.
5. It is recommended to connect the microphone with a gentel force and prevent
damage to the connector.
6. Please do not dissable the product since it may cause damages.
Notice
1. MIC Mute / Pairing Button
2. Power Button
3. Charging Status Indicator
4. Mic Connector (Detachable Microphone)
5. Volume Control
6. Charging Port (USB Type-C)
7. Reset Button
Product Overview
8. AUX Port
9. Transmitter Pairing Button
10. Transmitter Status Indicator
Reset Button
• To reset the headset to factory settings: insert a pointed object such as a pin into the hole
and push the button, the headset will be reset and powered off automatically.
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and radiates radio frequency energy, and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
▶ Reorient or relocate the receiving antenna.
▶ Increase the separation between the equipment and receiver.
▶ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
▶ Consult the dealer or an experienced radio/TV technician for help.
NOTE
▶ The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
▶ Shield interface cables and AC power cord, if any, must be used in order to comply
with the emission limits.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
▶ This device may not cause harmful interference.
▶ This device must accept any interference received, including interference that may
cause undesired operation.
FCC ID: I4L-GH50W
FCC RF Radiation Exposure Statements
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled
environment and are safe for intended operation as described in this manual. The further RF
exposure reduction can be achieved if the product can be kept as far as possible from the user
body or set the device to lower output power if such function is available.
Wireless Headset
Operating Frequency: 2403.35-2479.35MHz
Output power: < xx dBm
EU compliance statement
English: MSI Inc. hereby declares that this wireless device is in compliance with Directive
2014/53/EU.
Français: MSI Inc. déclare par la présente que ce dispositif sans fil est conforme à la Directive
2014/53/UE.
Deutsch: Hiermit erklärt MSI Inc., dass sich dieses drahtlose Gerät in Übereinstimmung mit
der Richtlinie 2014/53/EU befindet.
Intaliano: MSI. Inc. dichiara che questo depositivo wireless è conforme alla Direttiva 2014/53/
EU.
Español: Por medio de la presente, MSI Inc. declara que este dispositivo inalámbrico cumple
con la Directiva 2014/53/UE.
JAPAN VCCI CLASS B STATEMENT
この装置は、クラスB情報技術装置です。この装置は、家庭環境で使用する事を目的としてい
ますが、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起
こすことがあります。取扱説明書に従って正し取り扱いをして下さい。VCCI-B
本製品は、EMC準拠の周辺機器およびシステムコンポーネント間にシールドケーブル（イー
サーネットワークケーブル）が使用されている状況で、EMCへの準拠が実証されています。
ラジオ、テレビ、およびその他の電子機器への干渉が発生する可能性を低減するため、EMC
準拠の周辺機器およびシステムコンポーネント間にシールドケーブルを使用することが重要
です。
重要：MSIの許諾を得ることなく本製品に変更または改変を加えると、電磁両立性（EMC）お
よび無線に準拠しなくなり、製品を操作するための許諾が取り消されるおそれがあります。
NCC警語
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；
經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電
信管理法規定作業之無線電通信。低功率射頻器材忍受合法通信或工業、科學及醫療用電波輻
射性電機設備之干擾。
XXXXXXXXXXXXXX
XXX-XXXXXX
ISED Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions: (1)This device may not cause interference.(2)This device must
accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :(1)L’appareil ne doit pas produire de brouillage; (2)L’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
3715A-GH50W
5
6
8
9
2
1
3
4
10
7
English English English
繁體中文 繁體中文 繁體中文
IMMERSE
GH50 WIRELESS
