dji Assistant 2 for MG ユーザーガイド

MG 6-Channel

Intelligent Battery Charger

V1.0

2018.03

User Guide

使用说明

ユーザーガイド

사용자 가이드

©

2018

1

EN

CHS

JP

KR

User Guide 2

使用说明

9

ユーザーガイド

15

사용자가이드

22

Contents

Compliance Information 29

2

©

2018

EN

Disclaimer

Thank you for purchasing the MG 6-Channel Intelligent Battery Charger (hereinafter referred

to as the “ Product”). Read this disclaimer carefully before using this Product. By using this

Product, you hereby agree to this disclaimer and signify that you have read it fully. Please use this

Product in strict accordance with the manual and be sure to pay attention to the Warnings. SZ DJI

TECHNOLOGY CO., LTD. and its afliated companies assume no liability for damage(s) or injuries

incurred directly or indirectly from improper use of this Product. Misuse includes, but is not limited

to, using unapproved chargers, charging unapproved batteries, short-circuiting, overheating,

modifying the Product, or touching the terminals with skin or metal.

DJI

TM

is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its afliated

companies. Names of products, brands, etc., appearing in this manual are trademarks or registered

trademarks of their respective owner companies. This Product and manual are copyrighted by DJI

the prior written consent or authorization of DJI.

This disclaimer is produced in various languages. In the event of divergence among different

versions, the Chinese version shall prevail when the Product in question is purchased in China, and

English version shall prevail when the Product in question is purchased in any other region.

Warning

1. DO NOT use this product under direct sunlight, in rain or in a damp environment.

2. Keep the battery charger away from heat, pressure, water, ammable gases, corrosives, etc.

The charging hub should be kept in an environment with a temperature range of 32° to 113℉ (0℃

to 45℃).

3. Place the battery charger on a at and stable surface. Ensure the device is properly insulated

with the surrounding space sufcient for ventilation (> 50 cm) to prevent re hazards.

4. In case of re, be sure to use a dry powder re extinguisher. A liquid re extinguisher may lead

to an electrical hazard.

5. DO NOT unplug the cables when the battery charger is in use. Remove batteries after charging

is complete.

6. The battery charger is only compatible with batteries listed in the Specication section. DO NOT

attempt to use the battery charger with other battery models.

7. If there is any noticeable buildup, wipe the metal terminals with a clean, dry cloth.

8. DO NOT use the charging hub during a thunderstorm.

9. DO NOT drop, assemble or disassemble the batteries. Always ensure there is no short circuit

before connecting the batteries.

10. DO NOT use worn-out batteries and dispose of them properly when depleted.

11. Please refer to the batteries’ user guide for more safety instructions before use.

©

2018

3

EN

Introduction

Featuring the functionality of an ordinal battery charger and charging hub, the MG 6-Channel

Intelligent Battery Charger can connect up to 6 MG batteries and charge them in succession. When

in use, the battery charger will intelligently charge two batteries (one from each side) simultaneously,

improving charging efficiency. The max output power of the battery charger is 2400 W and two

different working modes are available for users to choose: fast charge and slow charge. Additionally,

the battery charger has the following functions: overcurrent protection, overcharging protection,

overheating protection, disconnection protection, quick voltage balancing, and status display.

Overview

Battery Charger

2

3

5

4

7

9

1

6

8

10

In the Box

MG 6-Channel Intelligent

Battery Charger × 1

GND Cable × 1

AC Power Cable × 1

Micro USB Cable × 1

After-sales Service

Card × 1

Product Information

Card × 1

User Guide × 1

1. Handle

2. Operation Panel

3. Ventilation Holes

4. Charging and Balancing Cable Storage

5. Battery Power Port

6. Charging and Balancing Cable

7. Update Port (Micro USB)

8. AC Power Port

9. GND Port

10. Fans

4

©

2018

EN

Using the Battery Charger

Ensure that the GND cable is connected to the GND Port with the other end grounded. Then strictly

follow the instructions below to use the battery charger.

The MG 6-Channel Intelligent Battery

Charger can connect up to 6 MG batteries. MG-12000P Flight Batteries are used in the following

illustrations.

1. Connect the battery charger to an AC power source.

2. Connect the battery to the charger.

a. Press to open the Charging and Balancing Port Cover on the battery, and then connect

the Charging and Balancing Cable on the battery charger to the battery’s Charging and

Balancing Port.

Insert the GND cable here with

the other end grounded

.

Operation Panel

1 2

3

4

5

1. Battery Charging Status LEDs

Each LED indicates the charging status

of the battery connected to Battery Power

Port with the corresponding number (1-6).

2. Warning Indicator

This indicator will be on when the battery

charger detects any abnormalities. If this

indicator is on, stop charging immediately.

3. Fast Charge Button

Press to enter Fast Charge mode.

4. Slow Charge Button

Press to enter Slow Charge mode.

5. Start/Stop Button

Press to turn on/off the battery charger.

©

2018

5

EN

4. Ensure all cables are correctly plugged in then press the “Start/Stop” button on the operation

panel of the charger. The six LEDs on the operation panel of the charging hub will alternate

blinking between red and green. The LEDs will light up in numerical order and then turn off,

which indicates that self-diagnosis is complete, and the device is in a good condition. Check the

Charging Errors if there are any errors during self-diagnosis.

5. Choose fast charge or slow charge after self-diagnosis is complete and if no errors were

detected, the battery charger will start working.

• Ensure that there are no obvious defects, i.e. jams, breakages or disconnections, on the

ports or cables before using the battery charger.

• Ensure that the batteries are in good condition without obvious defects, i.e. breakages or

disconnections, on the cables before charging.

• When the batteries are correctly connected, turn the battery charger on.

• Secure the Charging and Balancing Cable in its Storage Port when not use.

• When the battery temperature is below 34° F (10° C), the charging current will be limited

in Fast Charge mode. Accordingly, the charging time will be prolonged to be same

with that in Slow Charge mode. The battery charger will stop working when the battery

temperature is outside the range of 32° - 113° (0° - 45° C).

3. Repeat step 2 to connect other batteries. This battery charger can connect up to 6 MG Flight

Batteries at the same time.

b. Connect the battery’s power cable to the battery charger’s Battery Power Port.

6

©

2018

EN

* To use the MG 6-Channel Intelligent Battery Charger Update Kit, Windows XP and above is required.

Status LEDs Descriptions

During charging, when one of the batteries is abnormal due to a disconnection, high temperature,

low temperature, over-voltage or overcurrent, the Status LED with the corresponding battery number

will blink as a reminder. The Status LED will be solid green once charging is complete. Once this is

displayed, please disconnect the battery and the battery charger.

LED LED Blinking Pattern Description

The LEDs gradually become solid green

in numerical order of battery number

The battery charger is self-diagnosing.

Blinks red slowly

The battery with the corresponding number

is disconnected.

Blinks yellow slowly

The battery with the corresponding number

is charging.

—— Solid green

The battery with the corresponding number

is fully charged.

Blinks red quickly

The temperature of the battery with the

corresponding number is too high or too low.

Blinks green slowly

The battery with the corresponding number

is fully charged, but cell balancing is still

processing.

Firmware Update

DJI will release rmware updates when available. Refer to the ofcial DJI website and follow the

instructions below to update the rmware.

1. Download the update kit* from the ofcial DJI website (https://www.dji.com/mg-1s/info#downloads)

2. Connect the battery charger to a PC via the provided Micro USB cable, and then connect the

battery charger to an AC power source. Press the Start/Stop button to power on the battery

charger.

©

2018

7

EN

3. Launch the update kit. Then click “Test Version” to check the rmware information of the battery

charger. If the rmware version under the Device Information column of the battery charger is

lower than that displayed under the Upgrade File column, please update the battery charger.

Click “Upgrade ”to update the rmware of the battery charger.

• Ensure there are no obvious defects (i.e. jams, breakages, disconnections) on the ports

or cables before updating the battery charger.

• DO NOT connect the batteries when updating.

• DO NOT disconnect the devices during an update.

• If the PC cannot detect the battery charger, check if the cables are correctly connected.

• Click “Reset” if update fails. And then retry update.

Charging Errors

Please check the table below if there are any errors during charging.

No. Description Problem Troubleshooting

1

Pressed “Start/Stop”

button but no response

Loose connection of the AC cable,

or there is no electric supply

Try to reconnect, and check if

there is electric supply

2

Any of the LEDs on the

operation panel blinks

red slowly

The battery is not correctly

connected or there is a

disconnection on the battery.

Try to reconnect the battery

or check if any of the battery

cables are broken

3

Any of the LEDs on the

operation panel blinks

red quickly

High-temperature Warning:

The battery temperature is higher

than 122° F (50° C)

or

Low-temperature Warning:

The battery temperature is lower

than 32° F (0° C)

Place the battery in a suitable

temperature. Retry charging

after the temperature reaches

the right charging temperature

range.

8

©

2018

EN

4

Any of the LEDs on the

operation panel blinks

green slowly.

Charging is complete, but cell

balancing is still processing: The

battery is fully charged, but the

cells voltage differs

DO NOT disconnect the

battery to ensure the cells

balancing is continued. Please

change the battery if the cells

balancing takes too long

5

Any of the LEDs on the

operation panel are

solid red

Battery over-current, over-

voltage, under-voltage, or system

breakdown

Change the battery. Please

contact a DJI authorized

dealer if the problem

continues

Specications

Compatible Battery Models MG-12000*, MG-12000S*, MG-12000P

Input Rated Voltage/Frequency** 100 - 264 V / 50 - 60 Hz

Input Voltage Range/Frequency 90 - 240 V / 50 - 60 Hz

Charging Port Voltage 36 - 50.4 V

Rated Current

Fast Charge: 24 A

Slow Charge: 12 A

Output Capacity

2400 W (when two batteries are being charging

simultaneously and the voltage is 220 V)

1200 W (when only one battery is being charged)

Operation Temperature Range 32° to 113° F (0° to 45° C)

Dimensions 13.15 × 4.61 × 12.13 in (334 × 217 × 308 mm)

Weight 338 oz (10.5 kg)

*

A power cable adapter is required when the battery charger is used to charge MG-12000 and MG-12000S

Flight Batteries. This power cable adapter is used to connect the battery’s XT90 Power Port, the Communication

Port, and the battery charger’s Battery Power Port. MG-12000 and MG-12000S Flight Batteries’ Charging and

Balancing Port can be directly connected to the battery charger’s Charging and Balancing Cable.

**

The output capacity will be halved when the input voltage is 90~150 V.

The data was tested with air-cooling.

©

9

CHS

免责声明

感谢您购买 MG 六通道智能充电器（以下简称“充电器”）。在使用充电器之前，请仔细阅读

本声明，一旦使用，即被视为对本声明全部内容的认可和接受。请严格遵守本说明使用该产品，

并务必重视注意事项。因用户不当使用（包括但不限于：使用非指定型号的充电器，为非指定

型号的电池充电，使产品短路、发热、进入异物，用手或金属触碰端子等）造成的任何损失，

深圳市大疆

TM

创新科技有限公司及其关联公司将不承担任何责任。

DJI

TM

是深圳市大疆创新科技有限公司及其关联公司的商标。本文出现的产品名称、品牌等，均

经许可，不得以任何形式复制翻印。

关于不同语言版本的免责声明可能存在的语义差异，中国以中文版为准，其他地区以英文版为准。

注意事项

1. 请勿在阳光直射、雨淋或潮湿的环境中使用本产品。

2. 本产品应远离热源、高压、水、可燃性气体、腐蚀剂等危险物品。务必于合适的环境温度使

用充电器（建议 0℃ ~ 45℃）。

3. 产品需放置在水平台面，不能倾斜歪倒，四周务必留有足够通风距离 ( 建议 >50cm)，保障

产品工作时通风良好。

4. 若遇火警，请正确使用干粉灭火器进行灭火，使用液体类灭火器可能会有触电危险。

5. 请勿在工作过程中拔出输入线。充电完成后，请及时拔出电池。

6. 请严格按照参数表当中的适配电池型号为电池进行充电。请勿使用充电器为其他型号电池充电。

7. 若金属端子附有异物，请使用干燥的毛巾进行擦拭。

8. 严禁在雷雨天气中使用产品。

9. 连接电池前，切勿摔打电池，切勿将电池正负极短路，切勿自己拆装电池，以免发生危险。

10. 废弃电池请勿继续使用，请安全妥善处理。

11. 使用充电器对电池进行充电前，请仔细阅读电池的相关安全说明及使用注意，并严格按照

里面的内容进行操作。

物品清单

MG 六通道智能充电器 ×1

接地线 ×1

AC 电源线 ×1

Micro USB 连接线 ×1

售后服务卡 × 1

合格证 × 1

使用说明 ×1

10

©

CHS

简介

MG 六通道智能充电器是一款集充电器和充电管家为一体的二合一智能充电器，可连接 6 块 MG

飞行电池。充电时，充电器会智能将左右两边各一块电池进行组合，同步充电，可提高充电效率。

充电器最大输出功率高达 2400W，提供快充、慢充等两种模式供用户选择。此外，该充电器还

具有过流保护、过充保护、过温保护、断线保护、快速均衡及状态指示等功能。

部件名称

充电器

2

3

5

4

7

9

1. 提手

2. 控制面板

3. 散热孔

4. 充电平衡线固定口

5. 电池电源接口

6. 充电平衡线

7. 升级接口（Micro USB）

8. 交流电源接口

1

6

8

10

控制面板

1.电池充电状态 LED 灯

每个 LED 灯对应指示插入相同数字充电

接口的电池的充电状态。

2.警告

当出现充电异常时，警告标记将会亮起，

请立即停止充电。

9. 地线接口

10. 风扇

1 2

3

4

5

3.快充

点击选择对电池进行快充。

4.慢充

点击选择对电池进行慢充。

5.启动 / 停止

按下以打开或关闭充电器。

©

11

CHS

使用充电器

使用前请确认通过接地线将充电器外壳接地，并严格按照说明使用。MG 六通道智能充电器最

多可连接 6 块 MG 飞行电池，请参照如下步骤使用本产品（本手册以 MG-12000P 飞行电池为

例进行说明）。

1. 将充电器连接至交流电源。

2. 连接电池。

a. 先打开电池充电平衡接口保护盖，然后将充电器上的充电平衡线插入电池的充电平衡接口。

b. 将电池电源线插入充电器上的电池电源接口。

3. 重复以上步骤插入其他电池，最多可同时连接 6 块 MG 飞行电池。

连接接地线，另一端接地

12

©

CHS

4. 确认所有线已正确连接，按下控制面板的“启动 / 停止”按钮，此时充电器控制面板 6 个电

池充电状态 LED 灯红绿灯交替闪烁，然后 LED 灯按照数字顺序依次点亮，再同步熄灭。此时，

充电器完成自检，且已正常启动。如自检过程出现异常，请查阅常见故障说明章节，并根据

提示进行处理。

5. 充电器自检正常后，选择快充或慢充，选择完毕后充电器将按照所选工作模式进行工作，对

电池进行充电。

连接充电器前，请确保充电器的各个端口、输入线束无堵塞、破损、断线等明显缺陷。

充电前，请检查待充电池，确保各个端口及线束没有破损、断线等明显缺陷。

务必连接好电池后再启动充电器。

充电完成或不使用充电器时，请将充电器的充电平衡线固定至充电平衡线固定口，起

保护作用。

当电池温度低于 10℃时，为了保护电池，充电器快充模式电流将被限制，电池充电时

间延长，与慢充模式相同。电池温度过高（高于 45℃）或温度过低（低于 0℃）时，

充电器将会自动停止充电。

电池充电状态 LED 灯描述

充电过程中，当其中某块电池异常时（如断线、高温、低温、过压、过流），相应编号的 LED

灯将会提示。充电完成后，LED 灯将会呈绿灯常亮，此时请断开充电器和电池的连接。

LED 灯具体闪烁规则描述

LED1 至 LED6 按顺序绿灯逐渐点亮充电器正在自检。

LED 灯红灯慢闪相应编号的电池断线。

LED 灯黄灯慢闪相应编号的电池正在充电。

——

LED 灯绿灯常亮相应编号的电池已完成充电。

LED 灯红灯快闪相应编号电池温度过高或过低。

LED 灯绿灯慢闪相应编号电池充电完成，电压均衡中。

固件升级

若充电器需要更新，DJI 官网将发布固件升级程序，请留意产品下载页面并根据以下步骤进行固

件升级。

1. 前往 DJI 官网下载最新升级软件 *（https://www.dji.com/cn/mg-1p/info#downloads）

* MG 六通道智能充电器升级软件需 Windows XP 及以上系统，暂不支持 Mac OS 系统。

©

13

CHS

3. 打开升级软件，电脑上将会出现如下界面。点击“检测版本”检查当前充电器的版本信息，

若充电器信息栏显示的版本号低于升级文件栏版本号，则需对充电器进行升级。点击“升级”

开始对充电器升级。

2. 连接充电器至 PC，并使用 AC 电源线连接充电器至交流电源。然后按下“启动 / 停止”按钮

打开充电器。

连接充电器前，请确保充电器的各个端口、输入线束无堵塞、破损、断线等明显缺陷。

充电器升级过程中，严禁接插电池。

在线升级过程中，请勿断开设备间的连接。

若系统无法检测到充电器，请检查各设备连接是否松动；若无，请重新拔插 Micro

USB 连接线再尝试升级。

升级过程中出现失败提示时，请点击“复位”对设备进行复位操作后再次升级。

14

©

CHS

常见故障说明

常见充电器故障说明及处理方法请参阅下表：

序号故障描述存在问题处理方法

1

按充电器“启动 / 停止”

按钮无反应

AC 电源线接触不良、未插到位或无

输入电源

请尝试重新连接，并检

查是否输入电源

2

充电器控制面板有

LED 灯呈红灯慢闪

电池端子未全部正确插入接口或电

池存在断线

请尝试重新连接全部电

池端子或检查电池引出

线有无破损或断开

3

充电器控制面板有

LED 灯呈红灯快闪

高温警告：电池温度高于 50℃

或

低温警告：电池温度低于 0℃

将电池放置在合适的温

度下静置，待电池恢复

到适合充电的温度后再

尝试重新充电

4

充电器控制面板有

LED 灯呈绿灯慢闪

非均衡完成：电池已经完成充电，但

电芯电压差较大

让电池继续完成均衡补

电，如长时间不能完成，

建议更换新电池

5

充电器控制面板有

LED 灯呈红灯常亮

电池过流，过压，欠压及系统故障等

更换故障电池，若故障

仍然存在请及时联系 DJI

授权的经销商或 DJI

规格参数

适配电池型号 MG-12000*，MG-12000S*，MG-12000P

输入额定电压 / 频率 ** 100-264 V / 50-60 Hz

输入电压范围 / 频率 90-240 V / 50-60 Hz

充电端口电压 36-50.4 V

额定电流

快充：24 A

慢充：12 A

输出功率

2400 W （两块电池同时充电，且电压为 220 V 时）

1200 W （单个电池充电）

工作温度范围 0℃ -45℃

尺寸 334 × 217 × 308 mm

净重 10.5 kg

* 当使用该充电器为 MG-12000 和 MG-12000S 飞行电池进行充电时，需额外购买电源转接线，连接充电

器的电池电源接口和电池的 XT90 接口及电池通信接口。MG-12000 和 MG-12000S 飞行电池的充电平

衡接口可直接连接至充电平衡线。

** 当输入电压为 90~150 V 时，输出功率将会减半。

以上数据为采用风冷散热时测得。

JP

©

2018

15

MG 6-

SZ DJI TECHNOLOGY CO., LTD.

DJI

TM

SZ DJI TECHNOLOGY CO., LTD. DJI

DJI DJI

1.

2.

0 45

3.

>50cm

4.

5.

6.

7.

8.

9.

10.

11.

JP

16

©

2018

MG 6-

6 MG

2 1

2400W 2

2

3

5

4

7

9

1

6

8

10

MG 6-

1

GND 1

AC 1

Micro USB x 1

1

1.

2.

3.

4.

5.

6.

7. Micro USB

8. AC

9. GND

10.

JP

©

2018

17

GND GND

MG 6-

6 MG

MG-12000P

1. AC

2.

a.

b.

GND

1 2

3

4

5

1. LED

LED 1 6

2.

3.

4.

5.

JP

18

©

2018

4.

6 LED

LED

5.

•

• 10

0 45 C

3. 2 MG

6

JP

©

2018

19

* MG 6- Windows XP

Window OS

LED

LED LED

LED

DJI DJI

1. DJI *

(https://www.dji.com/mg-1s/info#downloads)

2. Micro USB PC

AC

ページが読み込まれています...

dji Assistant 2 for MG ユーザーガイド

このマニュアルも適しています

dji Assistant 2 for MG ユーザーガイド

他の言語で

関連論文

その他のドキュメント