dji 4-Channel Intelligent Battery Chargeb ユーザーガイド

タイプ
ユーザーガイド

このマニュアルも適しています

2600W 4-Channel
Intelligent Battery Charger
v1.4
2019.06
User Guide
使用说明
ユーザーガイ
사용자 가이드
©
2019  DJI All Rights Reserved.
1
EN
CHS
JP
KR
User Guide 2
使用说明
12
ユーザーガイド
22
사용자가이드
32
Contents
Compliance Information 41
2
©
2019  DJI All Rights Reserved.
EN
Disclaimer
Thank you for purchasing the 2600W 4-Channel Intelligent Battery Charger (hereinafter referred
to as the “Product”). Read this disclaimer carefully before using this Product. By using this
Product, you hereby agree to this disclaimer and signify that you have read it fully. Please use this
Product in strict accordance with the manual and be sure to pay attention to the warnings. SZ DJI
TECHNOLOGY CO., LTD. and its afliated companies assume no liability for damage(s) or injuries
incurred directly or indirectly from improper use of this Product. Misuse includes, but is not limited
to, using unapproved chargers, charging unapproved batteries, short-circuiting, overheating,
modifying the Product, or touching the terminals with skin or metal.
DJI
TM
is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its afliated
companies. Names of products, brands, etc., appearing in this manual are trademarks or registered
trademarks of their respective owner companies. This Product and manual are copyrighted by DJI
with all rights reserved. No part of this Product or manual shall be reproduced in any form without
the prior written consent or authorization of DJI.
This disclaimer is produced in various languages. In the event of divergence among different
versions, the Chinese version shall prevail when the Product in question is purchased in China, and
the English version shall prevail when the Product in question is purchased in any other region.
Warning
1. DO NOT use this product under direct sunlight, in rain, or in a damp environment.
2. Keep the battery charger away from heat, pressure, water, ammable gases, and corrosives.
3. The battery charger should be kept in an environment with a temperature range of 32° F to 113°
F (0° C to 45° C).
4. Place the battery charger on a at and stable surface. In order to prevent re hazards, make sure
the device is properly insulated and that there is sufcient space for ventilation (at least 50 cm).
5. In case of re, be sure to use a dry powder re extinguisher. A liquid re extinguisher may lead
to an electrical hazard.
6. DO NOT unplug the cables while the battery charger is in use. Remove batteries after charging
is complete.
7. If there is any noticeable buildup, wipe the metal terminals with a clean, dry cloth.
8. DO NOT use the battery charger during a thunderstorm.
9. Please refer to the batteries’ user guide for more safety instructions before use.
10. The AC power cable’s input current is 16 A. Please use a power outlet that can provide a
current exceeding 16 A.
11. When the battery charger is connected to a power outlet, the GND cable must be connected to
the GND port on the battery charger. Make sure that the other end of the GND cable is on the
ground. Please see Step 1 in Using the Battery Charger on how to connect the GND cable.
12. DO NOT hold the charging cables to carry the battery charger. Otherwise, the cables may be
damaged.
13. DO NOT use the battery charger in an area where batteries are stored. There should be a
distance of at least 30 cm between the battery charger and any charging batteries. Otherwise,
©
2019  DJI All Rights Reserved.
3
EN
Introduction
Featuring the functionality of a battery charger and charging hub, the 2600W 4-Channel Intelligent
Battery Charger can connect with up to four batteries. The max output power of the battery charger
is 2600 watts and users can choose between two different charging modes: quick charge and slow
charge. While charging, the battery charger monitors the batteries’ status and can automatically
adjust the charging current if required. The battery charger continues to charge even if the ventilation
holes are blocked.
Users can check the battery charging status LEDs and the warning indicator on the operation panel
of the battery charger to conrm if there are any errors. The battery charger can be connected to a
remote controller, and users can launch the DJI MG app to see more detailed information regarding
any errors. Additionally, the battery charger has the following functions: overcurrent protection,
overcharging protection, overheating protection, and status display.
* This 2600W 4-Channel Intelligent Battery Charger is available in two versions. One version is compatible
with T16 batteries and one version is compatible with MG-12000P batteries. The version compatible
with T16 batteries has an adapter at the end of the charging cable, while the version compatible with
MG-12000P batteries does not. The general descriptions in this manual apply to both versions. The
illustrations in this manual may vary from the actual product.
To make sure the battery charger is working normally, please purchase an official DJI AC cable
depending on the plug type of your region.
the battery charger or charging batteries may be damaged by excessive heating and may even
lead to a re hazard.
14. Keep the battery charger away from inammable materials while charging. DO NOT place the
battery charger or charging batteries on a blanket or any carpeted surfaces when in use.
15. For activation or firmware updates, the battery charger must be connected to the remote
controller of either the MG-1P or T16. Make sure the remote controller has been updated to the
latest version before activating or updating the battery charger.
16. To ensure the battery’s performance and prolong the battery’s service life, in quick charge
mode, the battery will not be charged to a power level of 100%. Switch to slow charge mode if
you want to charge the battery to 100%.
In the Box
2600W 4-Channel
Intelligent Battery Charger *
User Guide × 1
After-sales Service Card × 1
Product Information Card × 1
GND Cable
×1
×1
4
©
2019  DJI All Rights Reserved.
EN
Overview
Battery Charger
1
3
4
2
8
6
5
9
10
7
Operational Panel
1 2
3
4
* The battery charger compatible with MG-12000P batteries does not have this storage space.
** The version compatible with T16 batteries has an adapter at the end of the charging cable, while the
version compatible with MG-12000P batteries does not. The majority of the illustrations in this user guide
show the battery charger compatible with T16 batteries.
1. Operation Panel
2. Charging Cables Clamp
3. Air Vent
4. Charging Cables Storage *
5. Handle
6. Charging Cable **
7. Fan Cover
8. USB-C Port Cover
9. AC Power Port
10. GND Port
1. Charging Status LED × 4
Each LED indicates the charging status
of the battery connected to a charging
cable. The numbers (1-4) correspond to
the position of the charging cable on the
battery charger.
2. Warning Indicator
The warning indicator will be solid red if the
battery charger detects any abnormalities.
If this occurs, stop charging immediately.
Only start to charge again once the indicator
is no longer solid red.
3. Mode Button
Press to switch the charging mode. The
default charging mode is quick charge.
4. Power Button
Press to turn the battery charger on and
off.
©
2019  DJI All Rights Reserved.
5
EN
Activation
The battery charger requires activation before using for the rst time. If the warning indicator is
solid green, it means the battery charger has not been activated. Please follow the steps below to
activate your battery charger:
Method 1: Using DJI MG App
1. Connect the battery charger to a power outlet.
2. Connect the battery charger to your remote controller using a USB-C cable (not provided).
3. Run the DJI MG app.
4. Press the Power button to power on the battery charger.
5. Follow the prompts to nish activation.
Method 2: Using DJI ASSISTANT™ 2
1. Connect the battery charger to a power outlet.
2. Connect the battery charger to your PC using a USB-C cable (not provided).
3. Visit www.dji.com to download DJI Assistant 2. Install and run the software.
4. Use your DJI account to log in.
5. Press the Power button to power on the battery charger.
6. Click “2600W 4-Channel Intelligent Battery Charger” and follow the prompts to nish activation.
Insert the GND cable here
with the other end grounded
Make sure your PC or smart device can connect to the internet during activation.
Internet
Using the Battery Charger
Make sure that the GND cable is connected to the GND Port with the other end on the ground and
follow the instructions below to use the battery charger. Up to 4 batteries can be connected to the
2600W 4-Channel Intelligent Battery Charger.
1. Connect the battery charger to a power outlet.
6
©
2019  DJI All Rights Reserved.
EN
Before connecting the charging cable to the battery, make sure the plug adapter is
securely attached to the charging cable. Note: it is normal for there to be approximately 0.8
mm of the yellow part of the cable visible even when it is securely attached.
Make sure to place the charging battery on the same side that the charging cable is xed
to the battery charger.
b. If users wish to charge MG-12000P batteries using the battery charger compatible with T16
batteries, rst detach the plug adapter from the charging cable, then connect the charging
cable to the MG-12000P battery’s charging and balancing port.
2. Connect the battery to the battery charger.
For the battery charger compatible with T16 batteries:
a. When charging a T16 battery, make sure the plug adapter is attached to the charging cable
before attaching it to the battery you wish to charge.
Although the battery charger compatible with T16 batteries can be used to charge MG-
12000P batteries by removing the plug adapters, it is not recommended to charge T16
batteries and MG-12000P batteries at the same time. Doing so may negatively affect the
charging performance, or even damage the battery charger permanently.
Make sure to store plug adapters in a safe place for future use.
©
2019  DJI All Rights Reserved.
7
EN
For the battery charger compatible with MG-12000P batteries:
Connect the battery’s charging and balancing port to the charging cable.
Make sure to place the charging battery on the same side that the charging cable is xed
to the battery charger.
3. Make sure all cables are correctly connected and press the Power button on the operation
panel of the charger. The four LEDs, the warning indicator, and the quick charge and slow
charge indicators will simultaneously ash. After powering on, the only lights remaining will be
the Charging Status LEDs representing the batteries currently connected. This indicates that
the self-diagnosis is complete, and the device is working normally. For more information about
how to check if there are any errors during self-diagnosis, refer to LEDs and Warning Indicator
Description. Alternatively, connect the charger to a remote controller and launch the DJI MG app
to see detailed information about the errors.
4. If no errors are detected during self-diagnosis, the battery charger will begin to charge the
batteries. Press the Mode button to choose quick charge or slow charge mode (the default
charging mode is quick charge).
In quick charge mode, the battery charger will charge T16 batteries in order of their power level,
starting from highest to lowest. If MG-12000P batteries are being charged, the battery charger will
rst charge the two batteries with the highest power level, followed by the remaining two batteries.
In slow charge mode, the battery charger will first charge the batteries with the lower power
levels. Once all batteries have the same power level, they will all be charged simultaneously.
This applies to both T16 and MG-12000P batteries
Before use, make sure there are no obvious defects on the battery charger or batteries
(e.g., jams, breakages, or short circuits).
DO NOT turn the battery charger on unless the batteries are correctly connected.
When charging MG-12000P batteries in quick charge mode, note that the battery charger
will not reorder the charging priority if a battery is removed. This may lead to only one
battery being charged rather than a pair of batteries.
8
©
2019  DJI All Rights Reserved.
EN
In both quick charge and slow charge mode, the battery charger will automatically
adjust the charging current based on the condition of the batteries being charged. For
example, when in quick charge mode, if the battery temperature is below 59° F (15°
C) the charging current will be limited and the charging time will be prolonged. The
charging time depends on the battery model and battery temperature. The lower the
battery temperature, the longer the charging time will be. For different battery models, the
charging temperature range is different. Please see the battery’s user guide to check its
charging temperature range.
LEDs and Warning Indicator Description
During charging, the Status LED will blink when the corresponding charging battery is experiencing
an abnormality due to the cable being disconnected, a high or low temperature, overvoltage, or
overcurrent. Once charging is complete, the Status LED will be solid green. The battery can be
disconnected from the battery charge.
Charging Mode and Log Exports:
LED
Blinking Pattern
Quick
Charge Indicator
Slow
Charge Indicator
Description
Pulses green / Green
The battery in the corresponding
position to the number is in quick
charge mode.
Blinks green Green /
The battery in the corresponding
position to the number is in slow
charge mode.
Solid green / /
The charger’s logs are being
exported. Please restart the charger
after logs have been exported.
Charging Indicators
LED Blinking Pattern Warning Sound Description
Solid yellow /
The battery in the corresponding position to the
number is connected and queued to charge.
Solid green /
The battery in the corresponding position to the
number is fully charged.
Blinks yellow once
continuously
/
The temperature of the battery in the corresponding
position to the number is too low, and the charging
current is limited.
Blinks yellow twice
continuously
/
There is a large difference between the input voltage
and the battery voltage.
Blinks yellow three
times continuously
/
The temperature of the battery in the corresponding
position to the number is too low, and the battery
charger has stopped charging.
Blinks yellow four
times continuously
/
The temperature of the battery in the corresponding
position to the number is too high, and the battery
charger has stopped charging.
©
2019  DJI All Rights Reserved.
9
EN
Blinks red once
continuously
D.D.D…
The battery in the corresponding position is not
correctly connected or an unauthorized battery is
connected (this warning will only appear 10 seconds
after the battery is connected).
Blinks red twice
continuously
DD.DD.DD…
The connector short-circuited. Please check the
battery or the battery charger.
Solid red DDD.DDD… Critical error detected.
Note: The quick charge or slow charge indicator will remain solid during charging.
If the status LEDs do not light after the batteries and the power outlet are correctly connected,
there may be a problem with the battery charger. In this situation, the warning indicator will
light to indicate the following abnormalities:
Warning Indicator Warning Sound Description
Solid red / Self-diagnosis abnormal
Solid yellow / The input voltage is too low
Blinks yellow twice continuously / The fan of the 4850 module is abnormal
Blinks yellow three times continuously / The battery charger fan is abnormal
Blinks red once continuously D.D.D…… The 4850 module is abnormal
Solid red DD.DD.DD…… Main board is abnormal
If there are any abnormalities, please connect the battery charger to a remote controller and run
the DJI MG app to see more information. If the DJI MG app indicates that a module is abnormal or
broken, please contact DJI or a DJI authorized dealer.
Firmware Update
Follow the instructions below to update the rmware using the DJI MG app. Users will be notied
through the app when rmware updates are available.
1. Connect the battery charger to a remote controller using a USB Type-C cable and connect the
battery charger to a power outlet.
2. Power on the remote controller, and press the Power button on the operational panel to power
on the battery charger.
3. Run the DJI MG app, and follow the prompts to update the rmware. Make sure your remote
controller remains connected to the internet while updating.
Before using the battery, make sure there are no obvious defects on the ports or cables
of the battery charger (e.g., jams, breakages, or short circuits).
DO NOT connect the batteries while updating the battery charger’s rmware.
DO NOT disconnect the battery charger while updating the battery charger’s rmware.
Retry update if update fails.
Storage and Maintenance
10
©
2019  DJI All Rights Reserved.
EN
For the battery charger compatible with MG-12000P batteries, it is only necessary to secure the
charging cable end to the clamp on the side of the battery charger.
Replacing the Charging Cables
Follow these steps to replace the charging cables:
1. Loosen the screws and remove the panel.
Battery Charger Storage
When the battery charger is not in use, disconnect the batteries from the battery charger and the
battery charger from the power outlet. Follow the steps below to safely secure the charging cables.
1. After disconnecting a battery, wrap the charging cable over the battery charger.
2. Make sure the end of the charging cable is securely attached to the corresponding clamp on the
side of the battery charger.
2. Loosen the A and B screws, and press the C cable to disconnect the charging cable. Make sure
the charging cable is pointed vertically and slide the charging cable to the right to disconnect
from the battery charger completely.
©
2019  DJI All Rights Reserved.
11
EN
B
A C
White cable
Red cable
Blue cable
3. Make sure the red cable is aligned with “+”, and the blue cable with “–”. Secure the blue and red
cables using the A and B screws and press the C cable to insert the white cable in the middle.
4. Clamp the new charging cable’s end to where the original cable was. Attach the panel and
secure it using the screws.
Make sure the new charging cable’s end is in the vertical position shown in Step 2.
Otherwise, it may not be possible to attach the panel.
Specications
Compatible Battery Models T16 Batteries, MG-12000P Batteries
Rated Input Voltage/Frequency 110-220 V/ 50-60 Hz
Charging Voltage T16: 58.8 V; MG-12000P: 50.4 V
Rated Current
T16: Quick charge 45 A; Slow charge 17.5 A;
MG-12000P: Quick charge 24 A; Slow charge 12 A
Rated Power 220 V: 2600 W; 110 V: 1200 W
Operation Temperature Range -23° F to 122° F (-5° C to 50° C)
Dimensions Approx. 314×303×220 mm
Weight Approx. 9.14 kg
12
©
2019  大疆创新  版权所有
CHS
免责声明
感谢您购买 2600W 四通道智能充电器(以下简称“充电器”)。在使用充电器之前,请仔细阅
读本声明,一旦使用,即被视为对本声明全部内容的认可和接受。请严格遵守本说明使用该产品,
并务必重视注意事项。因用户不当使用(包括但不限于:使用非指定型号的充电器,为非指定
型号的电池充电,使产品短路、发热、进入异物,用手或金属触碰端子等)造成的任何损失。
深圳市大疆
TM
创新科技有限公司及其关联公司将不承担任何责任。DJI
TM
是深圳市大疆创新科
技有限公司及其关联公司的商标。本文出现的产品名称、品牌等,均为其所属公司的商标或注
册商标。本产品及手册为深圳市大疆创新科技有限公司版权所有。未经许可,不得以任何形式
复制翻印。
关于不同语言版本的免责声明可能存在的语义差异,中国以中文版为准,其他地区以英文版为准。
注意事项
1. 请勿在阳光直射、雨淋或潮湿的环境中使用本产品。
2. 本产品应远离热源、高压、水、可燃性气体、腐蚀剂等危险物品。务必于合适的环境温度使
用充电器(建议 0 ~ 45℃)。
3. 产品需放置在水平台面,不能倾斜歪倒,四周务必留有足够通风距离 ( 建议 >50cm),保障
产品工作时通风良好。
4. 若遇火警,请正确使用干粉灭火器进行灭火,使用液体类灭火器可能会有触电危险。
5. 请勿在工作过程中拔出输入线。充电完成后,请及时拔出电池。
6. 若金属端子附有异物,请使用干燥的毛巾进行擦拭,擦拭时确保充电器未接入外部电源。
7. 严禁在雷电及雷雨天气中使用产品。
8. 使用充电器对电池进行充电前,请仔细阅读电池的相关安全说明及使用注意,并严格按照里
面的内容进行操作。
9. 充电器 AC 电源线为 16A, 请确保外接的交流电源电流大于 16A
10. 当将充电器连接至外部电源时,务必同时连接接地线,并保持接地线的另一头连接地面。
具体接地线的连接方法,请查看使用充电器章节第一步示例图。
11. 移动或搬运充电器时,不要拉扯电池充电线。
12. 请选择开阔场地进行充电,务必远离电池存储区域。为保证充电安全,充电时,电池与充电器、
电池与电池之间的距离需大于 30cm,以免因为发热集中而导致的充电器或电池故障,甚至
造成火灾等严重后果。
13. 充电时,请远离可燃物,切勿将充电器或电池放置于地毯上进行充电。
14. 充电器仅支持连接至 MG-1P T16 植保无人飞机遥控器,激活和升级固件。通过连接遥控
器升级和激活充电器前,请确保已将遥控器固件升级至最新版本。
15. 快充状态下,为保护电池并延长电池寿命,电池电量将不会充满至 100%如需将电量充满,
请选择慢充模式。
©
2019  大疆创新  版权所有
13
CHS
简 
2600W 四通道智能充电器是一款集充电器和充电管家为一体的智能充电器,可连接 4 块电池
充电器最大输出功率高达 2600W,提供快充、慢充两种模式供用户选择。充电过程中,充电器
可实现与电池的通讯,并根据当前电池可接受的电流大小智能调整充电电流。充电器全新的自
我修复功能,即使在充电过程中发生散热孔堵塞等非致命性问题时也能自动调整充电电流,确
保充电持续进行。
充电器具备自检功能,用户可通过控制面板上的警告灯及 LED 灯提示,对充电器的异常情况进
行初步诊断,并可连接至遥控器,运行 DJI MG App 了解详细的异常情况说明。 此外,该款充
电器还具有过流保护、过充保护、过温保护及状态指示等功能。
部件名称
充电器
1
3
4
2
8
6
5
9
10
7
* 2600W 四通道智能充电器共有两款,主要区别在于电池充电线接口处,分别适配 T16 智能飞行电池和
MG-12000P 飞行电池。如无特别指出,本文所描述均为该款智能充电器的通用功能特性。同时,本文将
以适配 T16 智能飞行电池的充电器作为主要图示,从而进行讲解说明。用户所购买产品的实际外观结构
具体以实物为准。 
为保证产品的正常使用,用户需额外购买 AC 电源线,请根据所在国家选择不同规格的 AC 电源线。 
物品清单
2600W 四通道智能充电器 *
×1
售后服务卡 × 1
合格证 × 1
使用说明 ×1
接地线 ×1
14
©
2019  大疆创新  版权所有
CHS
1. 控制面板
2. 电池充电线固定卡口
3. 散热孔
4. 充电线转接头固定位 *
5. 提手
6. 电池充电线 **
7. 风扇保护盖
8. USB-C 口保护盖
9. 交流电源接口
10. 地线接口
激活充电器
首次使用的充电器需要激活。当警告灯为绿灯常亮时,表示该充电器尚未激活,请按照以下步
骤对充电器进行激活。
方法一:使用 DJI MG App 激活:
1. 将充电器连接至交流电源。
2. 使用 USB-C 连接线(需另购)连接充电器至遥控器。
3. 运行 DJI MG App
4. 打开充电器电源开关。
5. 根据 App 提示激活充电器。
方法二:使用 DJI ASSISTANT
TM
2 激活:
1. 将充电器连接至交流电源。
2. 使用 USB-C 连接线(需另购)连接充电器至 PC
3. 前往 www.dji.com 下载并安装 DJI Assistant 2 调参软件,然后运行。
4. 使用 DJI 账号登陆。
1.电池充电状态 LED ×4
每个 LED 灯对应指示插入充电接口位置
的电池的充电状态。
2.警告
当出现充电异常时,警告标记将会亮起。
若警告灯为红色,请停止充电,确保排
除异常后才可再次充电
3.快充 / 慢充切换按钮
短按可切换快充或慢充模式(开机后默
认为快充模式。选择后,该按钮上方
或下方的指示灯将会点亮。
4.启动 / 停止
按下以打开或关闭充电器。
控制面板
1 2
3
4
*  适配 MG-12000P 飞行电池的 2600W 四通道智能充电器无此充电线转接头固定位。 
**  两款 2600W 四通道智能充电器的电池充电线接口处结构有所不同,图示为适配 T16 智能飞行电池的充电
器外形结构。
©
2019  大疆创新  版权所有
15
CHS
2. 连接电池。
使用适配 T16 智能飞行电池的充电器:
a. 若连接 T16 智能飞行电池,请直接将电池电源接口插入电池即可。
连接接地线,另一端接地
5. 打开充电器电源开关。
6. 点击“2600W 四通道智能充电器”,然后根据提示激活充电器。
激活时,请确保 PC 或遥控器可以接入互联网。
Internet
使用充电器
使用前请确认通过接地线将充电器外壳接地,并严格按照说明使用。充电器最多可连接 4 块电池,
请参照如下步骤使用本产品。
1. 将充电器连接至交流电源。
连接充电线时,请检查充电线接口处的转接头是否安装到位(安装到位时,转接头处仅
能看到宽度为 0.8mm 的黄色细线)。若未到位,请用力推动转接头,确保转接头与充
电线接口处连接良好。
为达到良好的充电体验,请将充电线从固定位取下,绕回至另一侧连接电池。 
16
©
2019  大疆创新  版权所有
CHS
b. 若希望使用适配 T16 智能飞行电池的充电器为 MG-12000P 飞行电池充电,请首先用力拔
下电池充电线接口处的转接头,然后再将充电器上的电池充电线与 MG-12000P 的电池充
电线连接。
虽然通过插拔适配 T16 智能飞行电池的充电器电池充电线接口处的转接头,可让其同
时适配 MG-12000P 飞行电池和 T16 智能飞行电池,但切勿使用该充电器同时为 2
电池进行充电,否则将会影响充电效率,甚至损坏充电器。
取下电池充电线接口处的转接头后,请妥善保管该转接头,以免丢失。
使用适配 MG-12000P 飞行电池的充电器:
将充电器上的电池充电线与 MG-12000P 的电池充电线连接。
为达到良好的充电体验,请将充电线从固定位取下,绕回至另一侧连接电池。 
3. 确认所有线已正确连接,按下控制面板的“启动 / 停止”按钮,此时充电器控制面板 4 个电
池充电状态 LED 灯、警告灯、快充指示灯以及慢充指示灯将会被同步点亮,再同步熄灭,
然后已插入相应电池的 LED 灯将会呈黄灯常亮。此时,充电器完成自检,且已正常启动。如
自检过程出现异常,请查阅 LED 灯及警告灯描述章节了解异常原因,或连接至遥控器后打开
DJI MG App 获取详细的异常情况描述。
©
2019  大疆创新  版权所有
17
CHS
4. 充电器自检正常后,选择快充或慢充(开机后默认选择快充模式),选择完毕后充电器将按
照所选工作模式进行工作,对电池进行充电。
选择快充模式为 T16 智能飞行电池充电时,充电器将会按照电池剩余电量,由高到低依次
进行充电;若对 MG-12000P 飞行电池进行充电,充电器将会选择剩余电量较高的两块电
池进行充电,然后再对剩余的两块电池充电。当选择慢充模式对 T16 智能飞行电池或 MG-
12000P 飞行电池进行充电时,充电器将会首先对剩余电量较低的电池进行充电,待四块电
池剩余电量一致时智能对所有电池进行同步充电。
连接充电器前,请确保充电器的各个端口、输入线束无堵塞、破损、断线、短路等明
显缺陷。
充电前,请检查待充电池,确保各个端口及线束没有破损、断线等明显缺陷。
务必连接好电池后再启动充电器。
智能充电器会根据电池的性能调整慢充及快充模式下的充电电流。例如,一般情况下
当温度低于 15℃时,快充模式下,充电电流将被限制,电池充电时间延长。电池充电
时间与电池型号和温度相关,温度越低,电池的充电时间越长。不同的电池低温以及
高温禁止充电温度不同,具体的电池可充电温度范围请查看电池的相关文档。
快充模式下,为确保快充模式的连续性,若电池处于非充电状态,对其进行插拔,不
会对当前的充电进程造成影响;慢充模式下,若插拔电池,充电器会按照当前连接至
充电器的所有电池的电量重新进行排序,依次进行充电。
LED 灯及警告灯描述
充电过程中,当其中某块电池异常时(如断线、高温、低温、过压、过流),相应编号的 LED
灯将会提示。充电完成后,LED 灯将会呈绿灯常亮,此时请断开充电器和电池的连接。
充电模式及日志导出提示:
LED 闪烁规则
快充
指示灯
慢充
指示灯
说明
LED 灯绿灯呼吸 / 绿灯 相应编号电池正在使用慢充模式充电中。
LED 灯绿灯闪烁 绿灯 / 相应编号电池正在使用快充模式充电中。
LED 灯绿灯常亮 / /
充电器日志导出中,导出完毕后,请重启
充电器。
充电过程提示(充电过程中,根据所选模式,快充或慢充指示灯将会保持常亮):
LED 闪烁规则 提示音 说明
LED 灯黄灯常亮 / 相应编号插口已插入电池,等待充电。
LED 灯绿灯常亮 / 相应编号电池已完成充电。
LED 灯黄灯连续单闪 / 相应编号电池温度过低,充电电流被限制。
18
©
2019  大疆创新  版权所有
CHS
LED 灯黄灯连续双闪 / 输出电压与电池电压差较大。
LED 灯黄灯连续闪三次 / 电池温度过低,充电已被禁止。
LED 灯黄灯连续闪四次 / 电池温度过高,充电已被禁止。
LED 灯红灯连续单闪 D.D.D
电池未插好或电池非官方电池(检测到电
池插入后 10 秒左右提示)。
LED 灯红灯连续双闪 DD.DD.DD 接口短路,请检查电池和充电器。
LED 灯红灯常亮 DDD.DDD 检测到不可恢复异常。
若插入电池,接通外部电源,并开启充电器后 LED 灯不亮,此时可能充电器自身出现异常,警
告灯将会进行提示:
警告灯 提示音 说明
红灯常亮 / 充电器自检异常。
黄灯常亮 / 充电器输入电压过低。
黄灯连续双闪 / 充电器 4850 整流模块风扇异常。
黄灯连续闪三次 / 充电器机框风扇异常。
红灯连续单闪 D.D.D…… 充电器 4850 整流模块异常。
红灯常亮 DD.DD.DD…… 充电器主板异常。
当出现异常情况时,可将充电器通过 USB-C 口连接至遥控器,并运行 DJI MG App 查看详细的
异常说明。当遥控器提示模块异常或损坏时,建议用户联系 DJI DJI 授权的代理商维修或更
换故障模块。
固件升级
若充电器需要更新,DJI 官网将发布固件升级通知,请留意产品下载页面。请按照以下方式使用
DJI MG App 对充电器进行升级:
1. 使用 USB-C 连接线将充电器连接至飞行器遥控器,并使用 AC 电源线连接充电器至交流电源。
2. 开启遥控器,并按下充电器上的“启动 / 停止”按钮打开充电器。
3. 运行 DJI MG App,并根据提示进行固件下载升级。固件下载过程中需要连接互联网。
连接充电器前,请确保充电器的各个端口、输入线束无堵塞、破损、断线、短路等明
显缺陷。
充电器升级过程中,严禁接插电池。
在线升级过程中,请勿断开设备间的连接。
升级过程中出现失败提示时,请再次尝试重新升级。
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

dji 4-Channel Intelligent Battery Chargeb ユーザーガイド

タイプ
ユーザーガイド
このマニュアルも適しています

その他のドキュメント