Epson TM-T20II Series ユーザーマニュアル

タイプ
ユーザーマニュアル
1
User’s Manual
Standards and Approvals
Introduction
This manual describes how to replace the UB-S01 on TM series printers
designed for this board. You must check the printer DIP switches after
replacing the UB-S01. See the documentation that came with the printer for
information about setting the DIP switches.
About The Symbol In This Manual
CAUTION:
Cautions must be observed to avoid minor injury to yourself or damage
to your equipment.
The following standards are applied only to the interface
boards that are so labeled. (EMC is tested using the EPSON
power supplies and TM series printers.)
Europe: CE marking
North America: FCC/ICES-003 Class A
Japan: VCCI Class A
Oceania: AS/NZS CISPR22 Class A
CE Marking
These products conform to the following Directive and norms:
Directive 2004/108/EC
EN 55022 Class A
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-11
WARNING
This is a Class A product. In a domestic environment this
product may cause radio interference, in which case the user
may be required to take adequate measures.
The printers in which this board is installed becomes class A
devices.
The connection of a non-shielded printer interface cable to the
board will invalidate the EMC standards of this device.
You are cautioned that changes or modifications not expressly
approved by Seiko Epson Corporation could void your
authority to operate the equipment.
FCC Compliance Statement
For American Users
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual,
may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful
interference, in which case the user will be required
to correct the interference at his own expense.
For Canadian Users
This Class A digital apparatus complies with
Canadian ICES-003.
À l'intention des utilisateurs
canadiens
Cet appareil numérique de la classe A est conforme
à la norme NMB-003 du Canada.
Copyright © 1997 by Seiko Epson Corporation
Printed in China
2
Precautions
CAUTIONS:
Disconnect the power supply from the printer before you remove the
UB-S01; otherwise you may damage the UB-S01 and the printer. You
must disconnect the power supply because the electrical current is
flowing in some parts of the printer circuit even when the power switch
is turned off.
Wear a grounded wrist strap when handling the UB-S01 to prevent
damage from static electricity.
To avoid contamination, do not touch the board connector.
Unpacking
Make sure you have these items:
UB-S01
This manual
Procedure
1. Remove the two screws that securing the UB-BOARD; then pull the UB-
BOARD to remove it.
CAUTION:
Put the UB-BOARD into an anti-static bag for storage to prevent
damage from static electricity.
2. Hold the UB-S01 as shown in the illustration below. Push the UB-S01 in
gently until you feel the connector fit into place.
3. Secure the UB-S01 with the two screws.
4. Change the printer DIP switches to match the printer to the new interface.
See the printer documentation for information about these settings.
Make sure you set the printer DIP switches. Otherwise the printer may
not work correctly.
Connector of the UB-S01
Connector of the TM printer
1
ユーザーズマニュアル
はじめに
本書は、TM シリーズプリンター (UB-S01 対応 ) に取り付けられている UB-
S01 の交換方法について説明しています。UB-S01 交換後は、プリンターの
ディップスイッチの確認、または設定が必要になります。その際は、プリン
ターのマニュアルをご覧ください。
本書の記号の見方について
本書では、以下の記号が使われています。記号の意味をよく理解してから交
換作業をしてください。
注意 :
この表示を無視して、誤った取り扱いをすると、人が傷害を負う可能性が想
定される内容、および物的損害のみの発生が想定される内容を示しています。
電波障害自主規制について
注意:
この装置は、クラス A 情報技術装置です。この装置を家庭環境で使用すると
電波妨害を引き起こすことがあります。
この場合には使用者が適切な対策を講ずるよう要求されることがあります。
VCCI-A
交換作業上の注意
注意 :
作業の前にプリンターから電源を取り外してください。( 電源スイッチをオフ
にするだけでなく、電源を取り外してください。)
プリンターの電源スイッチをオフにしても、内部の回路基板には通電してい
るところがあります。電源を取り付けたまま交換作業を行うと、UB-S01、
およびプリンターが故障する可能性があります。
作業中は接地されたリストバンドを装着してください。リストバンドを装着
せずに作業をすると、静電気による故障の原因になります。
UB-S01 のコネクターを手で触れないでください。汚れによる動作不良を起こ
す可能性があります。
Copyright © セイコーエプソン株式会社 1997
Printed in China
2
同梱品
UB-S01
本書
交換手順
1. UB-BOARD を固定している 2 つのネジを外して、UB-BOARD を抜き取
ります。
注意 :
取り外した UB-BOARD は、静電気による故障を防ぐため、静電防止処理を
した袋などに保管してください。
2. 図のように、UB-S01 のコネクターをプリンターのコネクターに合わせま
す。UB-S01 を押して、コネクターを接続してください。
3. 2 つのネジで UB-S01 を固定します。
4. 新しいインターフェイスに合わせて、プリンターのディップスイッチを
変更します。
ディップスイッチの説明については、プリンターのマニュアルを参照し
てください。
ディップスイッチの設定は必ず行ってください。プリンターが正しく動
作しないことがあります。
UB-S01 のコネクター
TM プリンターのコネクター
1 / 1

Epson TM-T20II Series ユーザーマニュアル

タイプ
ユーザーマニュアル