简体中文
19
电池和充电器
电池
不论基于任何理由,都不要尝试打开
电池。
不要将电池暴露在水中。
不要将电池暴露在热源中。
不要将电池存放在温度可能超过 40°C 的
地方。
只在环境温度介于 10°C 和 40°C 之间
的情况下充电。
只能使用本设备随附的充电器为电池充
电。使用错误的充电器可能会导致触电
或电池过热。
处理电池时,请遵循“保护环境”部分
所提供的说明进行。
请勿通过刺破或摔打方式损坏电池组或
改变其形状,因为这可能会造成人身伤
害或火灾危险。
不要对损坏的电池充电。
在极端条件下,电池可能会发生泄漏。
如果您发现电池上有液体,请用布仔细
拭去液体。避免皮肤接触。
如果与皮肤或眼睛接触,请按照下面的
说明操作。
警告!电池液可能会导致人身伤害或财产
损失。如果与皮肤接触,请立即用清水
冲洗。如果出现红肿、疼痛或刺激,请就
医。如果与眼睛接触,请立即用清水冲洗
并就医。
充电器
您的充电器专门设计用于特定电压。请务
必检查电源电压是否与铭牌一致。
警告!切勿尝试使用一般的电源插头替换
充电器。
只能使用随附的 Black & Decker 充电器
为设备内的电池充电。其他非原厂电池
可能会爆裂,导致人身伤害和损害。
切勿尝试为不可再充电的电池充电。
如果电源线已损坏,必须让制造商或
Black & Decker 授权维修中心更换以避
免发生危险。
不要将充电器暴露在水中。
不要打开充电器。
不要刺破充电器。
充电时,设备/工具/电池必须放在通风
良好的地方。
电气安全
充电器上的符号
14
ENGLISH
(Original instructions)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace
the charger unit with a regular mains
plug.
u
Use your Black & Decker charger only
to charge the battery in the appliance
with which it was supplied. Other bat-
teries could burst, causing personal
injury and damage.
u
Never attempt to charge nonrecharge-
able batteries.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised Black & Decker Service
Centre in order to avoid a hazard.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/battery must be placed
in a well ventilated area when charg-
ing.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
w
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
transformer output.
x
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
taken to an authorised service centre for repair.
$
The charging base is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl door
7. Dust bowl
8. Brush tool
9. Floor extention release clip
10. Floor extention tube
11. Floor head release clip
12. Flip down brush
13. Floor head
14. Charging base
Wall Mounting
The charging base can be attached to a wall to provide a
convenient storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for chargeing the vac while it is on the wall
bracket).
u Insert the charger cord into the curved slot in the wall
mount bracket leaving approximately 20 cm excess.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
bracket.
Battery
Z
There are no user servicable part inside. For
safe recycling of the battery and internal com-
ponents please return the unit to an authorised
Black&Decker service centre.
使用设备前,请仔细阅读本手册。
14
ENGLISH
(Original instructions)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace
the charger unit with a regular mains
plug.
u
Use your Black & Decker charger only
to charge the battery in the appliance
with which it was supplied. Other bat-
teries could burst, causing personal
injury and damage.
u
Never attempt to charge nonrecharge-
able batteries.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised Black & Decker Service
Centre in order to avoid a hazard.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/battery must be placed
in a well ventilated area when charg-
ing.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
w
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
transformer output.
x
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
taken to an authorised service centre for repair.
$
The charging base is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl door
7. Dust bowl
8. Brush tool
9. Floor extention release clip
10. Floor extention tube
11. Floor head release clip
12. Flip down brush
13. Floor head
14. Charging base
Wall Mounting
The charging base can be attached to a wall to provide a
convenient storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for chargeing the vac while it is on the wall
bracket).
u Insert the charger cord into the curved slot in the wall
mount bracket leaving approximately 20 cm excess.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
bracket.
Battery
Z
There are no user servicable part inside. For
safe recycling of the battery and internal com-
ponents please return the unit to an authorised
Black&Decker service centre.
本工具采用双重绝缘,因此无需接
地线。请务必检查电源电压是否与
铭牌上的电压一致。
14
ENGLISH
(Original instructions)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace
the charger unit with a regular mains
plug.
u
Use your Black & Decker charger only
to charge the battery in the appliance
with which it was supplied. Other bat-
teries could burst, causing personal
injury and damage.
u
Never attempt to charge nonrecharge-
able batteries.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised Black & Decker Service
Centre in order to avoid a hazard.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/battery must be placed
in a well ventilated area when charg-
ing.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
w
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
transformer output.
x
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
taken to an authorised service centre for repair.
$
The charging base is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl door
7. Dust bowl
8. Brush tool
9. Floor extention release clip
10. Floor extention tube
11. Floor head release clip
12. Flip down brush
13. Floor head
14. Charging base
Wall Mounting
The charging base can be attached to a wall to provide a
convenient storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for chargeing the vac while it is on the wall
bracket).
u Insert the charger cord into the curved slot in the wall
mount bracket leaving approximately 20 cm excess.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
bracket.
Battery
Z
There are no user servicable part inside. For
safe recycling of the battery and internal com-
ponents please return the unit to an authorised
Black&Decker service centre.
短路保护安全隔离变压器。主电源
与变压器输出具有电气隔离。
14
ENGLISH
(Original instructions)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace
the charger unit with a regular mains
plug.
u
Use your Black & Decker charger only
to charge the battery in the appliance
with which it was supplied. Other bat-
teries could burst, causing personal
injury and damage.
u
Never attempt to charge nonrecharge-
able batteries.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised Black & Decker Service
Centre in order to avoid a hazard.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/battery must be placed
in a well ventilated area when charg-
ing.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
w
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
transformer output.
x
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
taken to an authorised service centre for repair.
$
The charging base is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl door
7. Dust bowl
8. Brush tool
9. Floor extention release clip
10. Floor extention tube
11. Floor head release clip
12. Flip down brush
13. Floor head
14. Charging base
Wall Mounting
The charging base can be attached to a wall to provide a
convenient storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for chargeing the vac while it is on the wall
bracket).
u Insert the charger cord into the curved slot in the wall
mount bracket leaving approximately 20 cm excess.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
bracket.
Battery
Z
There are no user servicable part inside. For
safe recycling of the battery and internal com-
ponents please return the unit to an authorised
Black&Decker service centre.
充电器会在温度环境变得太高时自
动关闭。因此,充电器将无法使
用。充电底座必须断开主电源,并
送到授权的服务中心进行维修。
14
ENGLISH
(Original instructions)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace
the charger unit with a regular mains
plug.
u
Use your Black & Decker charger only
to charge the battery in the appliance
with which it was supplied. Other bat-
teries could burst, causing personal
injury and damage.
u
Never attempt to charge nonrecharge-
able batteries.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised Black & Decker Service
Centre in order to avoid a hazard.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/battery must be placed
in a well ventilated area when charg-
ing.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
w
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
transformer output.
x
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
taken to an authorised service centre for repair.
$
The charging base is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl door
7. Dust bowl
8. Brush tool
9. Floor extention release clip
10. Floor extention tube
11. Floor head release clip
12. Flip down brush
13. Floor head
14. Charging base
Wall Mounting
The charging base can be attached to a wall to provide a
convenient storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for chargeing the vac while it is on the wall
bracket).
u Insert the charger cord into the curved slot in the wall
mount bracket leaving approximately 20 cm excess.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
bracket.
Battery
Z
There are no user servicable part inside. For
safe recycling of the battery and internal com-
ponents please return the unit to an authorised
Black&Decker service centre.
充电底座仅供室内使用。
部件名称
本工具包含如下部分或全部部件。
1. 电源开关
2. 手柄
3. 吸嘴
4. 拉出细缝吸嘴
5. LED 充电指示灯
6. 集尘仓门
7. 集尘仓
8. 刷头
9. 地板伸缩释放夹
10. 地板伸缩管
11. 地板头释放夹
12. 翻转刷头
13. 地板头
14. 充电底座