LS2-125AD
LED ARM MAGNIFIER
Thank you for purchasing the LS2-125AD LED Arm Type Magnifier.
Please read this manual thoroughly before use to insure proper operation and
long service.
To prevent electrical shock, always make sure the power is OFF and unplug the AC
Adapter before assembly or attaching/detaching lens or cleaning the equipment.
Never look at sun or bright light through the lens. There is risk of damage to eyesight.
Do not expose lens to sunlight or intense light, there is risk of starting fire.
Never leave lens in location where it can be exposed to direct or reflected sunlight.
Close the lens cover when not in use in order to prevent starting fire.
Keep hands from moving parts on the arm. There is risk of pinching fingers and injury.
Only use with the provided AC Adapter.
Handle with Care. Do not drop, scratch, or use strong force with product. (Use special
care when cleaning.) Mishandling may lead to product damage and injury.
Do not place the lens in water or rinse with water to clean. Water in long contact with
lens may cause mold or cloudiness.
The LED light is capable of frequent on/off cycles, but to avoid wear and damage to
the switch, do not cycle the switch unnecessarily.
This product contains metal bearing surfaces and may produce trace amount of dust
and powder due to repeated friction on metal surfaces. Therefore, it is not suitable for
clean-room applications. If there is concern over exposing workpiece to contamina-
tion, do not use for that application or take care not to reposition light while above
workpiece.
The clamp may scratch the desk surface and the movement of the light may cause
scratches on the top of the desk. To prevent, place a protective sheet or board
between desk and clamp surface.
Do not move the arm or lens housing beyond its limits. If overextended, the light may
tilt and cause damage or accident.
Please keep lens clean of dust and fingerprints.
Clean lens gently with dedicated lens cloth. Do not wash with abrasive cleaners, or
rinse with water.
Keep lens protection cover in down position, and unplug AC Adapter when not in use
for extended period.
Niigata seiki Co., Ltd.
5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-33-5522 Fax. : +81-256-33-5518
MAIL intl.sales@niigataseiki.co.jp
URL http://www.niigataseiki.co.jp
Makes work easy - Hands free; Well lit; Wide view.
Read and Follow for Safe Use of Product
BEFORE USE
Instruction Manual
WARNING
CARE & STORAGE NOTES
CAUTION
SPECIFICATIONS
Lens Protective Cover
LED Cover
Power
Dimming
AC Adapter jack
rear
Lens
Viewable Area
~䃥116mm
Clamp Range ~10 to 60mm
Arm Clamp
Arm
AC Adapter
Plug
Clamp
Arm Cover
For best results, and to prevent eye fatigue, adjust the Arm so that the Lens is parallel to
the surface you wish to inspect, and securely tighten the Clamp.The best lens position will depend on distance between eyes and the workpiece.
To use the Light, Plug the AC adapter into the Power Jack and press the Power Switch
to turn on power.
Position unit so that external lights, such as the ceiling fixtures, are not reflected in the lens.
Light power is controlled by using the buttons to adjust dimming.
After use, close the lens protection cover, turn off
the Power Switch, and unplug the AC adapter from
the power source.
Please Note: Due to product enhancements, appearance
and specifications are subject to change without notice.
Power Supply
Power
Bulb
Color Temp.
Luminous Power
AC Adapter
Main Unit Mass
Arm Length
AC100
-
240V
50/60 Hz AC Adapter included
~10W
60x White LED
~5,000 K daylight
~0 to 650 lumen
Cord Length ~1.5m
~2.3 kg
Upper ~490mm, Lower ~480mm
Type White Glass Lens
Magnification ~2x
Viewable Area ~䃥116mm
Head ABS
Arm Steel
Arm Cover ABS
LED Cover Polycarbonate
AC Adapter, Clamp,
Lens Cloth
Lens
Material
Accessories
HOW TO USE
PART NAMES, DIMENSIONS
Upper ~490mm
Lower ~480mm
ȭ
⩤⪺⪢ෛ࣍⏛
URL http://www.niigataseiki.co.jp
ȭ
/