Philips S8980/12 ユーザーマニュアル

S8980

1

4

5

6

7

8

9

2

3

10

11 12

1

English 6

简体中文 25

Introduction

Congratulations on your purchase and welcome

to Philips! To fully benet from the support that

Philips oers, register your product at

www.philips.com/welcome.

General description

1 Click-on shaving unit

2 Handle

3 Socket for small plug

4 Battery charge indicator with 1 light

5 Battery charge indicator with 3 lights

6 Unplug for use symbol

7 Travel lock symbol

8 Replacement reminder

9 Cleaning reminder

10 Supply unit

11 Small plug

12 Pouch

Important safety information

Read this important information carefully before

you use the appliance and save it for future

reference.

Danger

- Keep the supply unit dry.

English

6

Warning

- The appliance is a Class III

construction.

- To charge the battery, only

use the detachable supply unit

(type HQ8505) provided with

the appliance.

- The supply unit contains a

transformer. Do not cut o the

supply unit to replace it with

another plug, as this causes a

hazardous situation.

- This appliance can be used

by children aged from 8 years

and above and persons with

reduced physical, sensory or

mental capabilities or lack of

experience and knowledge

if they have been given

supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved.

English

7

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made

by children without supervision.

- Always unplug the shaver

before you clean it under the

tap.

- Always check the appliance

before you use it. Do not use

the appliance if it is damaged,

as this may cause injury. Always

replace a damaged part with

one of the original type.

- Do not open the appliance

to replace the rechargeable

battery.

English

8

Caution

- Never immerse the cleaning

system or the charging stand in

water and do not rinse it under

the tap.

- Never use water hotter than

80°C to rinse the shaver.

- Only use this appliance for its

intended purpose as shown in

the user manual.

- For hygienic reasons, the

appliance should only be used

by one person.

- Never use compressed air,

scouring pads, abrasive

cleaning agents or aggressive

liquids such as petrol or

acetone to clean the appliance.

- If your shaver comes with a

cleaning system, always use the

original Philips cleaning uid

(cartridge or bottle, depending

on the type of cleaning system).

English

9

- Always place the cleaning

system on a stable, level and

horizontal surface to prevent

leakage.

- If your cleaning system uses a

cleaning cartridge, always make

sure the cartridge compartment

is closed before you use the

cleaning system to clean or

charge the shaver.

- When the cleaning system is

ready for use, do not move it

to prevent leakage of cleaning

uid.

- Water may drip from the socket

at the bottom of the shaver

when you rinse it. This is normal

and not dangerous because

all electronics are enclosed in

a sealed power unit inside the

shaver.

English

10

- Do not use the supply unit in or

near wall sockets that contain

an electric air freshener to

prevent irreparable damage to

the supply unit.

Electromagnetic elds (EMF)

- This Philips appliance complies with all

applicable standards and regulations regarding

exposure to electromagnetic elds.

General

- This shaver is waterproof. It is suitable for use

in the bath or shower and for cleaning under

the tap. For safety reasons, the shaver can

therefore only be used without cord.

- The appliance is suitable for mains voltages

ranging from 100 to 240 volts.

- The supply unit transforms 100-240 volts to

a safe low voltage of less than 24 volts.

The display

Charging

Battery charge indicator with 3 lights

(specic types only)

Quick charge: When you connect the shaver to

the wall socket, the lights of the battery charge

indicator light up one after the other repeatedly.

When the appliance contains enough energy for

one shave, the bottom light of the battery charge

indicator starts to ash slowly.

English

11

While the appliance continues to charge, rst the

bottom light of the battery charge indicator ashes

and then lights up continuously. Then the second

light ashes and then lights up continuously,

and so on until the appliance is fully charged.

Battery fully charged

When the battery is fully charged, all lights of

the the battery charge indicator light up white

continuously.

Note: This appliance can only be used without

cord. If you press the on/o button during

charging, the 'unplug for use' symbol ashes white

to remind you that you have to disconnect the

appliance from the power outlet.

Note: When the battery is full, the display switches

o automatically after 30 minutes.

Battery low

When the battery is almost empty, the battery

charge indicator ashes orange.

When the battery is almost empty, the bottom light

of the battery charge indicator ashes orange.

Remaining battery charge

Battery charge indicator

The remaining battery charge is shown by the

lights of the battery charge indicator that light up

continuously.

English

12

’Unplug for use’ reminder

The appliance is equipped with an ‘unplug for

use’ reminder. The ‘unplug for use’ symbol ashes

to remind you that you have to disconnect the

appliance from the supply unit before you can

switch it on.

Cleaning reminder

Clean the shaver after every shave for optimal

performance. When you switch o the appliance,

the cleaning reminder ashes to remind you to

clean the appliance.

Travel lock

You can lock the appliance when you are going to

travel. The travel lock prevents the appliance from

being switched on by accident.

Activating the travel lock

1 Press the on/o button for 3 seconds to enter

the travel lock mode.

While you activate the travel lock, the travel

lock symbol lights up continuously. When the

travel lock is activated, the travel lock symbol

ashes.

Deactivating the travel lock

1 Press the on/o button for 3 seconds.

3 sec.

English

13

The travel lock symbol ashes and then lights

up continuously. The appliance is now ready

for use again.

Replacing shaving heads

For maximum shaving performance, we advise

you to replace the shaving heads every two years.

The appliance is equipped with a replacement

reminder which reminds you to replace the

shaving heads. The shaving unit symbol lights up

and the arrows ash to indicate that you have to

replace the shaving heads.

Note: After replacing the shaving heads, you need

to reset the replacement reminder by pressing the

on/o button for 7 seconds.

Charging

Charge the shaver before you use it for the rst

time and when the display indicates that the

battery is almost empty.

Charging takes approx. 1 hour.A fully charged

shaver has a shaving time of up to 50 minutes.

Note: You cannot use the appliance while it is

charging.

Charging with the supply unit

1 Make sure the appliance is switched o.

2 Put the supply unit in the wall socket and put

the small plug in the appliance.

3 After charging, remove the supply unit from the

wall socket and pull the small plug out of the

appliance.

1

2

English

14

Using the appliance

Note: This appliance can only be used without cord.

Switching the appliance on and o

- To switch on the appliance, press the on/o

button once.

- To switch o the appliance, press the on/o

button once.

Shaving

Skin adaption period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system.

We advise you to shave regularly (at least 3 times

a week) and exclusively with this shaver for a

period of 3 weeks to allow your skin to adapt to

the new shaver.

Dry shaving

1 Switch on the appliance.

2 Move the shaving heads over your skin in

circular movements.

Note: Circular movements provide better shaving

results than straight movements.

3 Clean the appliance after use

(see 'Cleaning and maintenance').

Wet shaving

You can also use this appliance on a wet face with

shaving foam or shaving gel.

English

15

To shave with shaving foam or shaving gel, follow

the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure

that the shaving unit glides smoothly over your

skin.

4 Switch on the appliance.

5 Move the shaving heads over your skin in

circular movements.

Note: Rinse the shaving unit regularly to ensure

that it continues to glide smoothly over your skin.

6 Dry your face.

7 Clean the appliance after use (see 'Cleaning

and maintenance').

Note: Make sure you rinse all foam or shaving gel

o the appliance.

English

16

Cleaning and maintenance

The accessories supplied may vary for dierent

products. The box shows the accessories that have

been supplied with your appliance.

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal

performance.

Caution: Be careful with hot water. Always check

if the water is not too hot, to prevent burning

your hands.

Never dry the shaving unit with a towel or tissue,

as this may damage the shaving heads.

1 Switch on the appliance.

2 Rinse the shaving unit under a warm tap.

3 Switch o the appliance. Pull the shaving head

holder o the bottom part of the shaving unit.

4 Rinse the hair chamber under the tap.

English

17

5 Rinse the shaving head holder under a warm

tap.

6 Carefully shake o excess water and let the

shaving head holder dry.

7 Attach the shaving head holder to the bottom

part of the shaving unit (‘click’).

Storage

Shaver

1 Store the appliance in the pouch (if supplied).

Note: Make sure the appliance is dry before you

store it in the pouch.

Replacement

Replacing the shaving heads

For maximum shaving performance, we advise

you to replace the shaving heads every two years.

Replace damaged shaving heads immediately.

Always replace the shaving heads with original

Philips shaving heads (see 'Ordering accessories').

Replacement reminder

2yrs

English

18

The replacement reminder indicates that the

shaving heads need to be replaced.The shaving

unit symbol and arrows light up when you switch

o the appliance.

1 Switch o the appliance.

2 Pull the shaving head holder o the bottom

part of the shaving unit.

3 Turn the retaining rings anticlockwise and

remove them.

4 Remove the shaving heads from the shaving

head holder.

5 Throw away the used shaving heads

immediately to avoid mixing them with the new

shaving heads.

6 Place the shaving heads in the shaving head

holder.

Note: Make sure the notches on both sides of the

shaving heads t exactly onto the projections in

the shaving head holder.

2

1

English

19

7 Place the retaining rings back onto the shaving

heads and turn them clockwise to reattach the

retaining ring.

- Each retaining ring has two recesses that t

exactly into the projections of the shaving head

holder. Turn the ring clockwise until your hear a

click to indicate that the ring is xed.

Note: Hold the shaving head holder in your hand

when you reinsert the shaving heads and reattach

the retaining rings. Do not place the shaving head

holder on a surface when you do this, as this may

cause damage.

8 Attach the shaving head holder to the bottom

part of the shaving unit (‘click’).

9 To reset the replacement reminder, press and

hold the on/o button for approx. 7 seconds.

Ordering accessories

To buy accessories or spare parts, visit

www.shop.philips.com/service or go to your

Philips dealer. You can also contact the Philips

Consumer Care Centre in your country (see the

worldwide guarantee leaet for contact details).

The following accessories and spare parts are

available:

- HQ8505 supply unit

- SH90 Philips shaving heads

- HQ110 Philips shaving head cleaning spray

Note: The availability of the accessories may dier

by country.

2

1

English

20

ページが読み込まれています...

Philips S8980/12 ユーザーマニュアル

Philips S8980/12 ユーザーマニュアル

他の言語で

関連論文