Philips S7530/43 ユーザーマニュアル

S7000 series

S7780, S7720, S7530

1

16

15

23

22

24

9

11

10

14

13

18

17

19

20 21

2

3

4

5

6

7

8

12

1

English 6

简体中文

35

English

6

Introduction

Congratulations on your purchase and welcome

to Philips! To fully benet from the support that

Philips oers, register your product at

www.philips.com/welcome.

General description

1 Protection cap for cleansing brush attachment

2 Click-on cleansing brush attachment

3 Comb for beard styler attachment

(specic types only)

4 Click-on beard styler attachment

(specic types only)

5 Click-on trimmer attachment

6 Click-on shaving unit

7 Handle

8 Socket for small plug

9 Battery charge indicator with 3 lights

10 Unplug for use symbol

11 Travel lock symbol

12 Replacement reminder

13 Cleaning reminder

14 Cleaning cartridge for SmartClean system

15 SmartClean system (specic types only)

16 Cap of SmartClean system

17 On/o button

18 Replacement symbol

19 Rinsing symbol

20 Ready symbol

21 Battery symbol

22 Supply unit

23 Small plug

24 Pouch

The accessories supplied may vary for dierent

products. The box shows the accessories that have

been supplied with your appliance.

English

7

Important safety information

Read this important information carefully before

you use the appliance and its accessories and save

it for future reference. The accessories supplied

may vary for dierent products.

Danger

- Keep the supply unit dry.

- This symbol means: Forbidden to clean under

a running tap.

Warning

- To charge the battery, only use the detachable

supply unit (HQ8505) provided with the appliance.

- The supply unit contains a transformer. Do not

cut o the supply unit to replace it with another

plug, as this causes a hazardous situation.

- This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made by

children without supervision.

- Always unplug the shaver before you clean it

under the tap.

- Always check the appliance before you use

it. Do not use the appliance if it is damaged,

as this may cause injury. Always replace a

damaged part with one of the original type.

- Do not open the appliance to replace the

rechargeable battery.

English

8

Caution

- Never immerse the cleaning system or the

charging stand in water and do not rinse it

under the tap.

- Never use water hotter than 80°C to rinse the

shaver.

- Only use this appliance for its intended purpose

as shown in the user manual.

- For hygienic reasons, the appliance should only

be used by one person.

- Never use compressed air, scouring pads,

abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the appliance.

- If your shaver comes with a cleaning system,

always use the original Philips cleaning uid

(cartridge or bottle, depending on the type of

cleaning system).

- Always place the cleaning system on a stable,

level and horizontal surface to prevent leakage.

- If your cleaning system uses a cleaning

cartridge, always make sure the cartridge

compartment is closed before you use the

cleaning system to clean or charge the shaver.

- When the cleaning system is ready for use, do

not move it to prevent leakage of cleaning uid.

- Water may drip from the socket at the bottom

of the shaver when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

- Do not use the supply unit in or near wall

sockets that contain an electric air freshener to

prevent irreparable damage to the supply unit.

Electromagnetic elds (EMF)

- This Philips appliance complies with all

applicable standards and regulations regarding

exposure to electromagnetic elds.

English

9

General

- This symbol means: Suitable to be used in the

shower. It is allowed to use this appliance close

to a bathtub, shower or other containers lled

with water.

- This shaver is waterproof. It is suitable for use

in the bath or shower and for cleaning under

the tap. For safety reasons, the shaver can

therefore only be used without cord.

- The appliance is suitable for mains voltages

ranging from 100 to 240 volts.

- The supply unit transforms 100-240 volts to a

safe low voltage of less than 24 volts.

The display

Charging

Note: If you press the on/o button during

charging, the 'unplug for use' symbol ashes white

to remind you that you have to disconnect the

appliance from the wall socket.

Battery charge indicator with 3 lights

Quick charge: When the battery is empty and you

connect the appliance to the wall socket, the lights

of the battery charge indicator light up one after

the other repeatedly. When the appliance contains

enough energy for one shave, the bottom light of

the battery charge indicator starts ashing slowly.

While the appliance continues to charge, rst the

bottom light of the battery charge indicator ashes

and then lights up continuously. Then the second

light ashes and then lights up continuously, and

so on until the appliance is fully charged.

English

10

Battery fully charged

Note: When the battery is full, the display switches

o automatically after 30 minutes.

Note: This appliance can only be used without

cord.

Battery charge indicator with 3 lights

When the battery is fully charged, all lights of

the the battery charge indicator light up white

continuously.

Note: When the battery is full, the display switches

o automatically after 30 minutes.

Battery low

Battery charge indicator with 3 lights

When the battery is almost empty, the bottom light

of the battery charge indicator ashes orange.

Remaining battery charge

Battery charge indicator with 3 lights

The remaining battery charge is shown by the

lights of the battery charge indicator that light up

continuously.

English

11

’Unplug for use’ reminder

The appliance is equipped with an ‘unplug for

use’ reminder. The ‘unplug for use’ symbol ashes

to remind you that you have to disconnect the

appliance from the supply unit before you can

switch it on.

Cleaning reminder

Clean the shaver after every shave for optimal

performance. When you switch o the appliance,

the cleaning reminder ashes to remind you to

clean the appliance.

Travel lock

You can lock the appliance when you are going to

travel. The travel lock prevents the appliance from

being switched on by accident.

Activating the travel lock

1 Press the on/o button for 3 seconds to enter

the travel lock mode.

3 sec.

English

12

While you activate the travel lock, the travel

lock symbol lights up continuously. When the

travel lock is activated, the travel lock symbol

ashes.

Deactivating the travel lock

1 Press the on/o button for 3 seconds.

The travel lock symbol ashes and then lights

up continuously. The appliance is now ready for

use again.

Replacing shaving heads

For maximum shaving performance, we advise

you to replace the shaving heads every two years.

The appliance is equipped with a replacement

reminder which reminds you to replace the shaving

heads. The shaving unit symbol lights up and the

arrows ash to indicate that you have to replace

the shaving heads.

Note: After replacing the shaving heads, you need

to reset the replacement reminder by pressing the

on/o button for 7 seconds.

Charging

Charge the shaver before you use it for the rst

time and when the display indicates that the

battery is almost empty.

Charging takes approx. 1 hour. A fully charged

shaver has a shaving time of up to 50 minutes.

Note: You cannot use the appliance while it is

charging.

English

13

Charging with the supply unit

1 Make sure the appliance is switched o.

2 Put the supply unit in the wall socket and put

the small plug in the appliance.

3 After charging, remove the supply unit from the

wall socket and pull the small plug out of the

appliance.

Charging in the SmartClean system (specic types

only)

1 Put the small plug in the back of the SmartClean

system.

2 Put the supply unit in the wall socket.

3 Press the top cap to be able to place the shaver

in the holder ('click').

4 Hold the shaver upside down above the

holder. Make sure the front of the shaver points

towards the SmartClean system.

5 Place the shaver in the holder (1), tilt the shaver

backwards (2) and press down the top cap to

connect the shaver (‘click’) (3).

The battery symbol starts to ash to indicate

that the appliance is charging. When the battery

is fully charged, the battery symbol lights up

continuously.

1

2

1

2

English

14

Using the appliance

Note: This appliance can only be used without

cord.

Switching the appliance on and o

1 To switch on the appliance, press the on/o

button once.

2 To switch o the appliance, press the on/o

button once.

Battery charge indicator with 3 lights: The display

lights up for a few seconds to show the remaining

battery status.

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system. To allow

your skin to adapt to this new appliance, we advise

you to shave regularly (at least 3 times a week)

and exclusively with this appliance for a period of

3 weeks.

Dry shaving

1 Switch on the appliance.

2 Move the shaving heads over your skin in

circular movements to catch all hairs growing in

dierent directions. Exert gentle pressure for a

close comfortable shave.

English

15

Note: Do not press too hard, this can cause skin

irritation.

3 Clean the appliance after use (see ‚Cleaning

and maintenance‘).

Wet shaving

You can also use this appliance on a wet face with

shaving foam or shaving gel.

To shave with shaving foam or shaving gel, follow

the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure

that the shaving unit glides smoothly over your

skin.

4 Switch on the appliance.

5 Move the shaving heads over your skin in

circular movements to catch all hairs growing in

dierent directions. Exert gentle pressure for a

close comfortable shave.

English

16

Note: Do not press too hard, this can cause skin

irritation.

Note: Rinse the shaving unit regularly to ensure

that it continues to glide smoothly over your skin.

6 Dry your face.

7 Clean the appliance after use (see‚ Cleaning

and maintenance‘).

Note: Make sure you rinse all foam or shaving gel

o the appliance.

Using the click-on attachments

Note: The accessories supplied may vary for

dierent products. The box shows the accessories

that have been supplied with your appliance.

Removing or attaching the click-on

attachments

1 Make sure the appliance is switched o.

2 Pull the attachment straight o the appliance.

Note: Do not twist the attachment while you pull it

o the appliance.

3 Insert the lug of the attachment into the slot in

the top of the appliance. Then press down the

attachment to attach it to the appliance (‘click’).

Using the trimmer attachment

You can use the trimmer attachment to groom

your sideburns and moustache.

1 Attach the attachment to the appliance ('click').

2 Switch on the appliance.

English

17

3 Hold the trimmer attachment perpendicular to

the skin and move the appliance downwards

while you exert gentle pressure.

4 Clean the attachment after use (see 'Cleaning

and maintenance').

Using the beard styler attachment with

comb

You can use the beard styler attachment with the

comb attached to style your beard at one xed

setting, but also at dierent length settings. You

can also use it to pre-trim any long hairs before

shaving for a more comfortable shave.

The length settings on the beard styler attachment

correspond to the remaining hair length after

cutting and range from 1 to 5mm.

1 Attach the attachment to the appliance ('click').

2 Slide the comb straight into the guiding grooves

on both sides of the beard styler attachment

(‘click’).

3 Press the length selector and then push it to

the left or right to select the desired hair length

setting.

4 Switch on the appliance.

2

1

English

18

5 Move the appliance upwards while you exert

gentle pressure. Make sure the front of the

comb is in full contact with the skin.

6 Clean the attachment after use (see 'Cleaning

and maintenance').

Using the beard styler attachment without

comb

You can use the beard styler attachment without

the comb to contour your beard, moustache,

sideburns or neckline to a length of 0.5mm.

1 Pull the comb o the beard styler attachment.

Note: Grab the comb in the center to pull it o the

beard styler attachment. Do not pull at the sides of

the comb.

2 Switch on the appliance.

3 Hold the beard styler attachment perpendicular

to the skin and move the appliance downwards

while you exert gentle pressure.

4 Clean the attachment after use (see 'Cleaning

and maintenance').

Using the cleansing brush attachment

Use the rotating cleansing brush attachment with

your daily cleansing cream. The cleansing brush

attachment removes oil and dirt, contributing to a

healthy and oil-free skin.

1 Attach the attachment to the appliance ('click').

English

19

2 Moisten the attachment with water.

Note: Do not use the appliance with a dry brush

attachment, as this can irritate the skin.

3 Moisten your face with water and apply a

cleanser to your face.

4 Place the attachment on your cheek.

5 Switch on the appliance.

6 Gently move the attachment across your skin

from the nose towards the ear. Do not push the

attachment too hard onto the skin to make sure

the treatment remains comfortable.

Note: Do not cleanse the sensitive area around

your eyes.

7 After approx. 20 seconds move the appliance

to your other cheek and start cleansing this part

of your face.

8 After approx. 20 seconds move the appliance

to your forehead and start cleansing this part

of your face. Gently move the brush head from

left to right.

Note: We advise you to not overdo the cleansing

and to not cleanse any zone longer than

20 seconds.

20 sec.

English

20

9 After the treatment, rinse and dry your face.

Your face is now ready for the next step of your

daily skincare routine.

10 Clean the attachment after use (see 'Cleaning

and maintenance').

Cleaning and maintenance

Note: The accessories supplied may vary for

dierent products. The box shows the accessories

that have been supplied with your appliance.

Cleaning the shaver in the SmartClean system (specic

types only)

Preparing the SmartClean system for use

Caution: Do not tilt the SmartClean system to

prevent leakage.

Note: Hold the SmartClean system while you

prepare it for use.

Note: If you clean the shaver in the SmartClean

system once a week, the SmartClean cartridge

lasts approximately three months.

1 Put the small plug in the back of the SmartClean

system.

2 Put the supply unit in the wall socket.

3 Press the button on the side of the SmartClean

system (1) and lift the top part of the

SmartClean system (2).

1

2

ページが読み込まれています...

Philips S7530/43 ユーザーマニュアル

このマニュアルも適しています

Philips S7530/43 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント