1
Thank you, and congratulations on your choice of the SRX-12
“Classic EPs” Wave Expansion Board.
This expansion board contains high-quality electric piano and clavi
sounds that are indispensable for a wide range of musical styles,
including R&B, hip-hop, pop, and jazz.
It provides three classic models of 73-note and 64-note electric
pianos, multisampled at each key over four levels of velocity. It also
provides clavi sounds sampled at each of four different pickup
settings, with mute both on and off.
The built-in patches were carefully selected to take full advantage of
the expressive power of the high-quality waveforms.
In addition, installing the Fantom-X6/X7/X8 Audio Track
Expansion will add the two screens “Classic EP” and “Classic Clav”
to Piano mode (the system must be updated to version 2.10 or later),
letting you adjust the sound via a simple and intuitive graphic user
interface.
• Waveforms: 168
• Patches: 105 (Fantom-X series, Fantom-S series, JUNO-G)
50 (SRX-compatible models other than listed above)
* The parameters of each patch are optimally adjusted for the
corresponding model, so the resulting output sound may vary.
Fantom-X6/X7/X8 users
If you’re installing this expansion board in a Fantom-X6/X7/
X8, we recommend that you update your Fantom-X6/X7/X8
system to version 2.10 or later. For details, refer to “About the
SRX-12 dedicated piano mode” (P.8).
Fantom-S/S88 users
If you have a Fantom-S/S88 with a system version earlier than
what’s shown below, you must update its system program so
that it will be able to correctly read Fantom-S/S88-specific data
from the SRX-12. (p. 16)
• Update required for versions up to Ver. 1.05
•
•
•
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT
NOTES” (p. 2; p. 4). These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new
unit, Owner’s Manual should be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
202
Copyright © 2006 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND
CORPORATION.
202
©
SRX-12_je.book 1 ページ ２００６年４月１１日 火曜日 午前１１時６分
ページが読み込まれています...
3
SRX-12_je.book 3 ページ ２００６年４月１１日 火曜日 午前１１時６分
4
IMPORTANT NOTES
When you purchase the SRX-12 expansion board from an
authorized Roland dealer, the included sounds and samples
are licensed, not sold, to you by Roland Corporation, for
commercial use in music production, public performance,
broadcast, etc.
You may use any of the included phrases and/or samples in
a commercial or non-commercial recording without paying
any additional license fees. However, you must strictly
adhere to the following crediting guidelines on any music
recording that utilize material from SRX-12.
Reproduction or duplication of this collection or any of the
sound recording contained in the SRX-12, either as they exist
on this expansion board or by any means of reformatting,
mixing, filtering, re-synthesizing, processing or otherwise
editing for use in another product or for re-sale, is strictly
prohibited without the express written consent of Roland. All
unauthorized giving, trading, lending, renting, re-issue, re-
distribution or re-sale of the sounds included in the SRX-12
are expressly prohibited.
In Plain English: Be creative in your application of the SRX-
12 sounds, and keep this library for your use only. DO NOT
COPY IT.
Roland constantly monitors other Soundware releases to
check for copyright infringements, and will prosecute all
piracy and copyright violations to the fullest extent of the
law.
THIS LIBRARY IS GUARANTEED TO BE 100%
COPYRIGHT CLEAN.
291a
In addition to the items listed under “USING THE UNIT
SAFELY” on page 2, please read and observe the following:
Handling CD-ROMs
801
* Avoid touching or scratching the shiny underside (encoded
surface) of the disc. Damaged or dirty CD-ROM discs may not
be read properly. Keep your discs clean using a commercially
available CD cleaner.
Handling the Board
901
To avoid the risk of damage to internal components that can
be caused by static electricity, please carefully observe the
following whenever you handle the board.
1
* Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been discharged.
2
* When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
5
* Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
901 (F)
Veuillez suivre attentivement les instructions suivantes
quand vous manipulez la carte afin d’éviter tout risque
d’endommagement des pièces internes par l’électricité
statique.
1
* Toujours toucher un objet métallique relié à la terre (comme
un tuyau par exemple) avant de manipuler la carte pour vous
décharger de l’électricité statique que vous auriez pu
accumuler.
2
* Lorsque vous manipulez la carte, la tenir par les côtés. Évitez
de toucher aux composants ou aux connecteurs.
5
* Conservez le sachet d’origine dans lequel était la carte lors de
l’envoi et remettez la carte dedans si vous devez la ranger ou la
transporter.
SRX-12_je.book 4 ページ ２００６年４月１１日 火曜日 午前１１時６分
5
INSTALLING THE WAVE EXPANSION BOARD
* Turn off your instrument.
1.
Remove the cover located on the top (or rear) of your
instrument.
928
* When turning the unit upside-down, get a bunch of newspapers or
magazines, and place them under the four corners or at both ends to
prevent damage to the buttons and controls. Also, you should try to
orient the unit so no buttons or controls get damaged.
929
* When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
2.
Insert the Wave Expansion Board connector into a connector
for an SRX Series slot, while simultaneously inserting the
board holders into the holes in the Wave Expansion Board.
911
* Do not touch any of the printed circuit pathways or connection
terminals.
912
* Never use excessive force when installing a circuit board. If it doesn’t
fit properly on the first attempt, remove the board and try again.
3.
Use the supplied Installation Tool to turn the holders in the
LOCK direction, so the board will be fastened in place.
(To remove the Wave Expansion Board, turn the board holders
in the UNLOCK direction, and lift up the board.)
913
* When circuit board installation is complete, double-check your work.
4.
Using the screws removed in Step 1, refasten the cover in its
original position.
5.
Check if the Wave Expansion Board is correctly installed.
* If the “EXP” display cannot be selected (doesn’t appear) in the
Waveform Selection Screen (refer to the owner’s manual of the
instrument you use), remove the Wave Expansion Board and install it
properly.
* Éteindre l’instrument.
1.
Retirer le couvercle situé sur le dessus (ou á l’arrière) de
l’instrument.
2.
Inserer le connecteur de la carte dans un des creneaux pour
la serie SRX tout en enfoncant les supports a carte dans les
trous de celle-ci.
911(F)
* Ne pas toucher aux circuits imprimés ou aux connecteurs.
912(F)
* Ne jamais forcer lors de l’installation de la carte de circuits imprimés.
Si la carte s’ajuste mal au premier essai, enlevez la carte et
recommencez l’installation.
3.
Utiliser l’outil d’installation fourni pour tourner les clips de
retenue vers la position de blocage (LOCK) de façon á ce que
la carte soit retenue en place.
(Pour retirer la carte d’expansion Wave, tourner les clips de
retenue de la carte vers la position déblocage (UNLOCK) et
retirer la carte en la soulevant.)
913(F)
* Quand l’installation de la carte de circuits imprimés est terminée,
revérifiez si tout est bien installé.
4.
Remettre la plaque a sa place et la fixer a l’aide des vis
enlevees a l’etape 1.
5.
S’assurer que la carte d’expansion Wave est installée
correctement.
* S’il est impossible de sélectionner l’affichage “EXP” (il n’apparaît pas)
á l’écran de sélection Waveform (se reporter au guide du propriétaire
de l’instrument utilisé), retirer la carte d’expansion Wave et la
réinstaller correctement.
1.
2.
3.
4.
5.
21 3
Wave Expansion Board (SRX series)
Carte d'extension Wave (serie SRX)
Connector
Connecteur
Board holder
Support à carte
Position them as shown before you install the board.
Avant l’installation, orienter les supports à carte tel qu’indiqué sur le schéma.
LOCK
Installation tool
Outil d'installation
Screwdriver
Tournevis
SRX-12_je.book 5 ページ ２００６年４月１１日 火曜日 午前１１時６分
6
When playing patches on the expansion board, we recommend that
you set all the EFFECTS ON/OFF settings on the Fantom series/XV
series to “ON.” If such settings are set to “OFF,” you may not obtain
the intended sound.
* Note that the Release Time has been set to a fairly long value for some
of the patches. As a result, if your sound generator has been set so
“Patch Remain” is “ON,” the release portion of a previously sounding
patch may continue to be heard even after switching to a new patch.
* Refer to the owner’s manual for your instrument for specific
instructions on how to play Patches on the expansion board.
Patch List (1)
For Fantom-X series/Fantom-S series/JUNO-G
(BANK SELECT MSB: 93; LSB: 26)
No. Name Voices Category
1 Pure EP1 1 EL.PIANO
2 Lo-Fi EP1 1 EL.PIANO
3 Pure EP2 1 EL.PIANO
4 Phaser EP1 1 EL.PIANO
5 Soft Wurly 1 EL.PIANO
6 Pure Wurly 1 EL.PIANO
7 Pure Clav DB 2 KEYBOARDS
8 Pure Clav CB 2 KEYBOARDS
9 PhaseClav CB 4 KEYBOARDS
10 Wah Clav CB 2 KEYBOARDS
11 Comp Clav CB 2 KEYBOARDS
12 PureClavMtCB 2 KEYBOARDS
13 St.Trem EP1 1 EL.PIANO
14 St.Trem EP2 1 EL.PIANO
15 Chorus Wurly 1 EL.PIANO
16 Chorus EP1 1 EL.PIANO
17 Chorus EP2 1 EL.PIANO
18 Dp-Cho EP1 1 EL.PIANO
19 Dp-Cho EP2 1 EL.PIANO
20 Soft EP1 1 EL.PIANO
21 Soft EP2 1 EL.PIANO
22 Phase Wurly 1 EL.PIANO
23 Hard EP1 1 EL.PIANO
24 Moving EP1 3 EL.PIANO
25 EP1 w/FM 3 EL.PIANO
26 EP1 w/VOX 3 EL.PIANO
27 EP1 w/STR 3 EL.PIANO
28 EP1 w/PAD 3 EL.PIANO
29 Flanger EP1 1 EL.PIANO
30 Flanger EP2 1 EL.PIANO
31 FlangerWurly 1 EL.PIANO
32 Melodic EP1 1 EL.PIANO
33 Amped EP1 1 EL.PIANO
34 Amped EP2 1 EL.PIANO
35 Lo-Fi EP2 1 EL.PIANO
No. Name Voices Category
36 Lo-Fi Wurly 1 EL.PIANO
37 ModDly EP1 1 EL.PIANO
38 ModDly EP2 1 EL.PIANO
39 Dual EP1 2 EL.PIANO
40 Dual Wurly 2 EL.PIANO
41 Enhance Clav 2 KEYBOARDS
42 Peaking Clav 2 KEYBOARDS
43 Dual Clav DB 4 KEYBOARDS
44 Dual Clav DA 4 KEYBOARDS
45 Dual Clav CB 4 KEYBOARDS
46 Dual Clav CA 4 KEYBOARDS
47 DualClavMtDB 4 KEYBOARDS
48 DualClavMtCB 4 KEYBOARDS
49 PhaseClav DB 4 KEYBOARDS
50 PhaseClvMtCB 4 KEYBOARDS
51 /EPtype1Cnd1 1 EL.PIANO
52 /EPtype1Cnd2 1 EL.PIANO
53 /EPtype1Cnd3 1 EL.PIANO
54 /EPtype1Cnd4 1 EL.PIANO
55 /EPtype1Cnd5 1 EL.PIANO
56 /EPtype2Cnd1 1 EL.PIANO
57 /EPtype2Cnd2 1 EL.PIANO
58 /EPtype2Cnd3 1 EL.PIANO
59 /EPtype2Cnd4 1 EL.PIANO
60 /EPtype2Cnd5 1 EL.PIANO
61 /EPtype3Cnd1 1 EL.PIANO
62 /EPtype3Cnd2 1 EL.PIANO
63 /EPtype3Cnd3 1 EL.PIANO
64 /EPtype3Cnd4 1 EL.PIANO
65 /EPtype3Cnd5 1 EL.PIANO
66 /Bite1 Pk1 4 KEYBOARDS
67 /Bite2 Pk1 4 KEYBOARDS
68 /Bite3 Pk1 4 KEYBOARDS
69 /Bite4 Pk1 4 KEYBOARDS
70 /Bite5 Pk1 4 KEYBOARDS
No. Name Voices Category
71 /Bite1 Pk2 4 KEYBOARDS
72 /Bite2 Pk2 4 KEYBOARDS
73 /Bite3 Pk2 4 KEYBOARDS
74 /Bite4 Pk2 4 KEYBOARDS
75 /Bite5 Pk2 4 KEYBOARDS
76 /Bite1 Pk3 4 KEYBOARDS
77 /Bite2 Pk3 4 KEYBOARDS
78 /Bite3 Pk3 4 KEYBOARDS
79 /Bite4 Pk3 4 KEYBOARDS
80 /Bite5 Pk3 4 KEYBOARDS
81 /Bite1 Pk4 4 KEYBOARDS
82 /Bite2 Pk4 4 KEYBOARDS
83 /Bite3 Pk4 4 KEYBOARDS
84 /Bite4 Pk4 4 KEYBOARDS
85 /Bite5 Pk4 4 KEYBOARDS
86 /Bite1 Pk1Mt 4 KEYBOARDS
87 /Bite2 Pk1Mt 4 KEYBOARDS
88 /Bite3 Pk1Mt 4 KEYBOARDS
89 /Bite4 Pk1Mt 4 KEYBOARDS
90 /Bite5 Pk1Mt 4 KEYBOARDS
91 /Bite1 Pk2Mt 4 KEYBOARDS
92 /Bite2 Pk2Mt 4 KEYBOARDS
93 /Bite3 Pk2Mt 4 KEYBOARDS
94 /Bite4 Pk2Mt 4 KEYBOARDS
95 /Bite5 Pk2Mt 4 KEYBOARDS
96 /Bite1 Pk3Mt 4 KEYBOARDS
97 /Bite2 Pk3Mt 4 KEYBOARDS
98 /Bite3 Pk3Mt 4 KEYBOARDS
99 /Bite4 Pk3Mt 4 KEYBOARDS
100 /Bite5 Pk3Mt 4 KEYBOARDS
101 /Bite1 Pk4Mt 4 KEYBOARDS
102 /Bite2 Pk4Mt 4 KEYBOARDS
103 /Bite3 Pk4Mt 4 KEYBOARDS
104 /Bite4 Pk4Mt 4 KEYBOARDS
105 /Bite5 Pk4Mt 4 KEYBOARDS
For Fantom (FA-76)/XV series/MX-200 (BANK SELECT MSB: 93; LSB: 26)
No. Name Voices Category
1 Pure EP1 1 EL.PIANO
2 Lo-Fi EP1 1 EL.PIANO
3 Pure EP2 1 EL.PIANO
4 Phaser EP1 1 EL.PIANO
5 Soft Wurly 1 EL.PIANO
6 Pure Wurly 1 EL.PIANO
7 Pure Clav DB 2 KEYBOARDS
8 Pure Clav CB 2 KEYBOARDS
9 PhaseClav CB 4 KEYBOARDS
10 Wah Clav CB 2 KEYBOARDS
11 Comp Clav CB 2 KEYBOARDS
12 PureClavMtCB 2 KEYBOARDS
13 St.Trem EP1 1 EL.PIANO
14 St.Trem EP2 1 EL.PIANO
15 Chorus Wurly 1 EL.PIANO
16 Chorus EP1 1 EL.PIANO
17 Chorus EP2 1 EL.PIANO
No. Name Voices Category
18 Dp-Cho EP1 1 EL.PIANO
19 Dp-Cho EP2 1 EL.PIANO
20 Soft EP1 1 EL.PIANO
21 Soft EP2 1 EL.PIANO
22 Phase Wurly 1 EL.PIANO
23 Hard EP1 1 EL.PIANO
24 Moving EP1 3 EL.PIANO
25 EP1 w/FM 3 EL.PIANO
26 EP1 w/VOX 3 EL.PIANO
27 EP1 w/STR 3 EL.PIANO
28 EP1 w/PAD 3 EL.PIANO
29 Flanger EP1 1 EL.PIANO
30 Flanger EP2 1 EL.PIANO
31 FlangerWurly 1 EL.PIANO
32 Melodic EP1 1 EL.PIANO
33 Amped EP1 1 EL.PIANO
34 Amped EP2 1 EL.PIANO
No. Name Voices Category
35 Lo-Fi EP2 1 EL.PIANO
36 Lo-Fi Wurly 1 EL.PIANO
37 ModDly EP1 1 EL.PIANO
38 ModDly EP2 1 EL.PIANO
39 Dual EP1 2 EL.PIANO
40 Dual Wurly 2 EL.PIANO
41 Enhance Clav 2 KEYBOARDS
42 Peaking Clav 2 KEYBOARDS
43 Dual Clav DB 4 KEYBOARDS
44 Dual Clav DA 4 KEYBOARDS
45 Dual Clav CB 4 KEYBOARDS
46 Dual Clav CA 4 KEYBOARDS
47 DualClavMtDB 4 KEYBOARDS
48 DualClavMtCB 4 KEYBOARDS
49 PhaseClav DB 4 KEYBOARDS
50 PhaseClvMtCB 4 KEYBOARDS
SRX-12_je.book 6 ページ ２００６年４月１１日 火曜日 午前１１時６分
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
13
1.
2.
1.
2.
1.
2.
SRX-12_je.book 13 ページ ２００６年４月１１日 火曜日 午前１１時６分
14
•
•
SRX-12_je.book 14 ページ ２００６年４月１１日 火曜日 午前１１時６分
15
1.
2.
1.
2.
1.
2.
•
•
SRX-12_je.book 15 ページ ２００６年４月１１日 火曜日 午前１１時６分
16
*04232245- 02*
04232245 ’06-05-2N
Fantom-S/S88 users
If the instrument in which you want to install the SRX-12 is running system
program
version 1.05 or earlier
, you must update the system before you can use
the SRX-12.
For instructions on checking the system program version for Fantom-S/S88, and
upgrading the software, please access the Roland website or contact the nearest
Roland Service Center.
About the Included CD-ROM
The included CD-ROM features:
• Fantom-X6/X7/X8 Audio Track Expansion system program (Ver. 2.1)
For more detailed information on each file, refer to Readme_E.pdf on the CD-
ROM.
* Take proper care of the included CD-ROM; it will not be reissued.
* The system programs on the included CD-ROM are the latest versions, as of
January, 2006. For information regarding newer versions than those on this disk,
you should contact the nearest Roland Service Center.
•
SRX-12_je.book 16 ページ ２００６年４月１１日 火曜日 午前１１時６分
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
