Philips S5015/61 ユーザーマニュアル

S5130

S5110

S5015

S5013

S5011

S5010

S5008

Question?

有疑问?

Contact Philips

请联系飞利浦

1

S5130/04 , S5110/04 , S5015/61, S5013/04 , S5011/04 , S5010/03, S5008/ 04

ENGLISH 6

简体中文 28

6

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips

offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

1 Protection cap for shaving unit

2 Click-on shaving unit

3 On/off button

4 Handle

5 Socket for small plug

6 Adapter

7 Small plug

8 Battery charge indicator

9 Travel lock symbol

10 Replacement reminder

(S5130/04, S5110/04, S5013/04 only)

11 Cleaning reminder

(S5130/04, S5110/04, S5013/04 only)

12 Click-on nose trimmer attachment

(S5015/61 only)

13 Protection cap for nose trimmer attachment

(S5015/61 only)

14 Click-on trimmer attachment

(S5130/04, S5110/04, S5015/61, S5013/04,

S5011/04, S5008/04 only)

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

ENGLISH

Important safety information

Read this important information carefully before you

use the appliance and its accessories and save it for

future reference. The accessories supplied may vary

for different products.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug,

as this causes a hazardous situation.

- This appliance is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

- Children should be supervised to ensure that they

do not play with the appliance.

- Always unplug the shaver before you clean it

under the tap.

- Always check the appliance before you use it.

Do not use the appliance if it is damaged, as this

may cause injury. Always replace a damaged part

with one of the original type.

Caution

- Never immerse the cleaning system or the charging

stand in water and do not rinse it under the tap.

- Never immerse the shaver in water. Do not use

the shaver in the bath or in the shower.

-

Never use water hotter than 80°C to rinse the shaver.

- Only use this appliance for its intended purpose as

shown in the user manual.

ENGLISH 7

- For hygienic reasons, the appliance should only be

used by one person.

- Never use compressed air, scouring pads,

abrasive cleaning agents or aggressive liquids such

as petrol or acetone to clean the appliance.

- If your shaver comes with a cleaning system,

always use the original Philips cleaning uid

(cartridge or bottle, depending on the type of

cleaning system).

- Always place the cleaning system on a stable,

level and horizontal surface to prevent leakage.

- If your cleaning system uses a cleaning cartridge,

always make sure that the cartridge compartment

is closed before you use the cleaning system to

clean or charge the shaver.

- When the cleaning system is ready for use,

do not move it to prevent leakage of cleaning uid.

- Water may drip from the socket at the bottom

of the shaver when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

Electromagnetic elds (EMF)

- This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic elds.

General

- This shaver can be safely cleaned under the tap.

- The appliance is suitable for mains voltages ranging

from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe

low voltage of less than 24 volts.

ENGLISH8

The display

Charging

Battery charge indicator

- Charging takes approx. 1 hour (S5130/04,

S5110/04, S5013/04 only) or 8 hours (S5015/61,

S5011/04, S5010/03, S5008/04 only).

- Quick charge (S5130/04, S5110/04, S5013/04

only): When the appliance does not contain

enough energy for one shave, the battery charge

indicator ashes quickly. When the battery charge

indicator starts ashing slowly, the appliance

contains enough energy for one shave .

- If you leave the appliance connected to the mains,

the charging process continues. To indicate that

the appliance is charging, the battery charge

indicator ashes slowly.

Battery fully charged

Note: You can also use this appliance directly from the

mains.

Note: When the battery is full, the display switches off

automatically after 30 minutes.

- When the battery is fully charged, the light of the

battery charge indicator lights up continuously.

Battery low

- When the battery is almost empty, the battery

charge indicator ashes orange.

ENGLISH 9

Cleaning reminder

For optimal shaving performance, we advise you to

clean the shaver after every use.

- When you switch off the shaver, the cleaning

reminder ashes to remind you to clean the

shaver (S5130/04, S5110/04, S5013/04 only).

Travel lock

You can lock the shaver when you are going to

travel. The travel lock prevents the shaver from being

switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

- While you activate the travel lock, the travel lock

symbol lights up continuously. When the travel

lock is activated, the travel lock symbol ashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

- The travel lock symbol ashes and then lights up

continuously.

The shaver is now ready for use again.

3 sec.

ENGLISH10

Replacing shaving heads

For maximum shaving performance, we advise you

to replace the shaving heads every two years.

- The appliance is equipped with a replacement

reminder (S5130/04, S5110/04, S5013/04 only)

which reminds you to replace the shaving heads.

The replacement reminder lights up white

continuously.

Note: After replacing the shaving heads, you need to

reset the replacement reminder by pressing the on/off

button for 7 seconds.

Charging

Charging takes approx. 1 hour (S5130/04, S5110/04,

S5013/04) or 8 hours (S5015/61, S5011/04,

S5010/03, S5008/04 only).

Note: You can also use this appliance directly from the

mains.

Charge the shaver before you use it for the rst

time and when the display indicates that the battery

is almost empty.

Charging with the adapter

1 Insert the small plug into the appliance and put

the adapter in the wall socket.

ENGLISH 11

Using the shaver

Switching the appliance on and off

1 To switch on the appliance, press the on/off

button once.

2 To switch off the appliance, press the on/off

button once.

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard

need time to adapt to any new shaving system.

We advise you to shave regularly (at least 3 times

a week) with this shaver for a period of 3 weeks to

allow your skin to adapt to the new shaver.

Note: You can also use the shaver directly from the mains.

1 Switch on the appliance.

2 Move the shaving heads over your skin in

circular movements.

Note: Do not make straight movements.

3 Clean the shaver after use

(see chapter ‘Cleaning and maintenance’).

ENGLISH12

Using the click-on attachments

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Removing or attaching the click-on

attachments

1 Make sure the appliance is switched off.

2 Pull the attachment straight off the appliance.

Note: Do not twist the attachment while you pull it off

the appliance.

3 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

Using the trimmer attachment

(S5130/04, S5110/04, S5015/61, S5013/04,

S5011/04, S5008/04 only)

You can use the trimmer attachment to groom

your sideburns and moustache.

1 Make sure the appliance is switched off.

2 Insert the lug of the attachment into the slot

in the top of the shaver. Then press down

the trimmer attachment to attach it to the

appliance (‘click’).

3 Switch on the appliance.

4 You can now start trimming.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

ENGLISH 13

Using the nose trimmer attachment

(S5015/61 only)

You can use the nose trimmer attachment to trim

your nose hair.

Make sure your nostrils are clean.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

2 Switch on the appliance.

3 Carefully insert the attachment into one of

your nostrils.

Do not insert the attachment more than

0.5cm into your nostrils.

4 Slowly move the attachment around to remove

all unwanted hairs in your nostrils.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Trimming ear hair

You can use the nose trimmer attachment to trim

your ear hair. Make sure your outer ear channels are

clean and free from wax.

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

2 Switch on the appliance.

3 Slowly move the attachment along the rim of

the ear to remove hairs that stick out beyond

the rim.

ENGLISH14

4 Insert the attachment into the outer ear

channel.

Do not insert the attachment more than 0.5cm

into your ear channel, as this could damage the

eardrum.

5 Slowly turn the attachment around to remove

all unwanted hairs from your outer ear

channel.

6 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Cleaning and maintenance

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Cleaning the shaver under the tap

Clean the shaver after every shave for optimal

shaving performance.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

Never dry the shaving unit with a towel or tissue,

as this may damage the shaving heads.

1 Rinse the shaving unit under a warm tap for

some time.

2 Press the release button and open the shaving

unit.

ENGLISH 15

3 Rinse the shaving head holder under a warm

tap for 30 seconds.

4 Carefully shake off excess water and let the

shaving head holder dry.

5 Close the shaving head holder (‘click’).

Thorough cleaning method

Make sure the appliance is switched off.

1 Press the release button and open the shaving

unit.

2 Pull the shaving head holder off the bottom

part of the shaving unit.

3 Turn the retaining rings anticlockwise and

remove them.

4 Remove the shaving heads from the shaving

head holder. Each shaving head consists of a

cutter and guard.

Note: Do not clean more than one cutter and guard at a

time, since they are all matching sets. If you accidentally

put a cutter in the wrong shaving guard, it may take several

weeks before optimal shaving performance is restored.

ENGLISH16

5 Clean the cutter and guard under the tap.

6 After cleaning, place the cutter back into the

guard.

7 Put the shaving heads back into the shaving

head holder.

Note: Make sure the projections of the shaving heads

t exactly into the recesses of the shaving-head holder.

8 Place the retaining rings back onto the shaving

head holder and turn them clockwise.

ENGLISH 17

- Each retaining ring has two recesses and two

projections that t exactly in the projections and

recesses of the shaving head holder.

- Turn the retaining ring clockwise until your hear

‘click’ and the ring is xed.

Note: Hold the shaving head holder in your hand

when you reinsert the shaving heads and reattach the

retaining rings. Do not place the shaving head holder

on a surface when you do this, as this may cause

damage.

9 Reinsert the hinge of the shaving head holder

into the slot of the shaving unit. Close the

shaving head holder (‘click’).

Cleaning the click-on attachments

Never dry the trimmer attachments with a towel

or tissue, as this may damage the trimming teeth.

Cleaning the trimmer attachment

(S5130/04, S5110/04, S5015/61, S5013/04,

S5011/04, S5008/04 only)

Clean the trimmer attachment every time you have

used it.

ENGLISH18

1 Switch on the appliance with the trimmer

attachment attached.

2 Rinse the trimmer attachment under a hot tap

for some time.

3 After cleaning, switch off the appliance.

4 Carefully shake off excess water and let the

trimmer attachment dry.

Tip: For optimal trimmer performance, lubricate the

trimmer teeth with a drop of sewing machine oil every

six months.

Cleaning the nose trimmer attachment

(S5015/61 only)

Clean the nose trimmer attachment every time you

have used it.

1 Make sure the appliance is switched off.

2 Rinse the cutting element of the nose trimming

head with hot water.

3 Switch on the appliance and rinse the cutting

element once more to remove any remaining

hairs. Then switch off the appliance again.

4 Carefully shake off excess water and let the

nose trimmer attachment dry.

Tip: For optimal trimmer performance, lubricate the

trimmer teeth with a drop of sewing machine oil every

six months.

ENGLISH 19

Storage

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Note: We advise you to let the appliance and its

attachments dry before you put the protection caps on

the attachments and store the shaver in the pouch.

- S5015/61 only: Place the protection cap on the

nose trimming head.

- Put the protection cap on the shaving head to

protect it from dirt accumulation.

Replacement

Replacing the shaving heads

For maximum shaving performance, we advise you

to replace the shaving heads every two years.

Replace damaged shaving heads immediately.

Only replace the shaving heads with original Philips

shaving heads as specied in chapter

‘Ordering accessories’.

Replacement reminder

(S5130/04, S5110/04, S5013/04 only)

The shaving unit symbol will light up to indicate that

the shaving heads need to be replaced.

1

S5130/04, S5110/04, S5013/04 only: The shaving

unit symbol lights up continuously when you

switch off the shaver to indicate that the shaving

heads need to be replaced.

ENGLISH20

ページが読み込まれています...

Philips S5015/61 ユーザーマニュアル

このマニュアルも適しています

Philips S5015/61 ユーザーマニュアル

他の言語で

関連論文