Philips RQ310/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル
ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Make sure the adapter does not get
wet (Fig. 1).
- The adapter contains a transformer.
Do not cut off the adapter to replace
it with another plug, as this causes a
hazardous situation.
Warning
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with the
appliance.
- Be careful with hot water when you
clean the appliance. Always check if the
water is not too hot, to prevent your
hands from getting burnt.
Caution
- Charge, use and store the shaver at a
temperature between 5°C and 35°C.
- Always put the protection cap on the
shaver to protect the shaving heads
when you are travelling.
- The shaver and the accessories are not
dishwasher-proof.
- Never use water hotter than 80°C to
rinse the shaver.
- Only use the adapter supplied.
- Do not use the shaver or the adapter if
it is damaged.
- If the adapter is damaged, always have
it replaced with one of the original type
in order to avoid a hazard.
- Water may leak from the socket at the
bottom of the shaver when you rinse
it. This is normal and not dangerous
because all electronics are enclosed in
a sealed power unit inside the shaver.
Compliance with standards
- This shaver complies with the
internationally approved safety
regulations and can be safely cleaned
under the tap (Fig. 2).
- This Philips appliance complies with all
standards regarding electromagnetic
elds (EMF). If handled properly
and according to the instructions in this
user manual, the appliance is safe to use
based on scientic evidence available
today.
General
- The adapter transforms 100-240 volts
to a safe low voltage of less than 24
volts.
General description (Fig. 3)
1 Protection cap
2 Shaving unit with shaving head holder
3 Shaving head holder release buttons
4 On/off slide
5 Retaining ring
6 Cutter
7 Shaving guard
8 Shaving head holder
9 Cleaning brush
10 Adapter
11 Charging light
12 Small plug
Charging
It takes approx. 10 hours to fully charge the
battery.
A fully charged shaver provides up to 20
shaving minutes.
If you have a heavy beard, the shaver may
provide less than 20 shaving minutes. The
number of shaving minutes may also vary
over time, depending on your shaving
behaviour, cleaning habits and beard type.
’Charging’ indication
- When the shaver is charging, the light
on the adapter lights up (Fig. 4).
RQ328, RQ320, RQ311, RQ310
Register your product and get support at
www.philips.com/welcome
4222.002.5401.3
3
1 2 4
5 6 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
26
25/01/2013
Charging
Do not charge the shaver in the packaging.
1 Switch off the shaver.
2 Put the small plug in the shaver.
3 Put the adapter in the wall socket.
, The light on the adapter lights up to
show that the shaver is charging.
Note: The light on the adapter does not
change colour and does not go out when the
shaver is fully charged.
Using the shaver
Note: You can use this shaver while it is
connected to the mains. However, it does not
operate from the mains when the battery is
empty. In this case, rst charge the shaver for
at least 1 hour.
Shaving
Skin adaptation period
Your rst shaves may not bring you the
result you expect and your skin may even
become slightly irritated. This is normal. Your
skin and beard need time to adapt to any
new shaving system.
We advise you to shave regularly (at least
3 times a week) for a period of 3 weeks to
allow your skin to adapt to the new shaver.
During this period, use your new electric
shaver exclusively and do not use other
shaving methods. If you use different shaving
methods, it is more difcult for your skin to
adapt to the new shaving system.
1 Move the on/off slide upwards to
switch on the shaver.
2 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 5).
3 Move the on/off slide downwards to
switch off the shaver.
4 Clean the shaver after every
shave (see chapter ‘Cleaning and
maintenance’).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol
or acetone to clean the shaver and its
accessories.
- Clean the shaver after every shave.
- Clean the shaving heads frequently
with Philips Shaving Head Cleaning
Spray (HQ110) for optimal shaving
performance.
- You can clean the outside of the
shaver with a damp cloth. Do not clean
the shaving unit with a cloth.
Cleaning the shaving unit
Be careful with hot water. Always check if
the water is not too hot, to prevent your
hands from getting burnt.
1 Switch off the shaver.
2 Rinse the shaving unit under a hot tap
for some time (Fig. 6).
Note: You can also clean the shaving unit with
the cleaning brush supplied.
3 After rinsing the appliance under the
tap, hold it upright for 10-15 seconds
to allow water to run out of the
bottom.
4 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit
(2). (Fig. 7)
5 Rinse the shaving head holder under a
hot tap for 30 seconds (Fig. 8).
Note: You can also clean the shaving head
holder with the cleaning brush supplied.
6 Carefully shake off excess water and
let the shaving head holder dry.
Never dry the shaving head holder with
a towel or tissue, as this may damage the
shaving heads.
7 Reattach the shaving head holder
to the shaving unit (‘click’) (Fig. 9).
Extra-thorough cleaning method
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit
(2) (Fig. 10).
3 To unlock the orange retaining ring,
turn it in the direction of the arrows
indicated in and on the retaining
ring (Fig. 11).
4 Lift the retaining ring out of the
shaving head holder. (Fig. 12)
5 Remove the cutter and the shaving
guard (Fig. 13).
Note: Do not clean more than one cutter
and shaving guard at a time, since they are
all matching sets. If you accidentally put a
cutter in the wrong shaving guard, it may
take several weeks before optimal shaving
performance is restored.
6 Clean the cutter with the cleaning
brush supplied (Fig. 14).
7 Clean the inside of the shaving
guard (Fig. 15).
8 After cleaning, place the shaving guard
back into the shaving head holder.
Make sure the two wings t exactly
into the recesses of the shaving head
holder (Fig. 16).
9 Place the cutter back into the shaving
guard with the cutter legs pointing
downwards (Fig. 17).
10 Place the retaining ring back onto the
shaving head holder (1). To reattach
the retaining ring, turn it against the
direction of the arrows indicated in
and on the retaining ring (2) (Fig. 18).
Note: Make sure the retaining ring is xed
properly. The four wings of the retaining ring
have to be located exactly under the recesses
of the shaving head holder (Fig. 19).
11 Reattach the shaving head holder to
the shaving unit (‘click’). (Fig. 9)
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Storage
Note: Make sure the shaving unit is dry before
you store the shaver.
1 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 20).
Replacement
For maximum shaving performance, we
advise you to replace the shaving heads
every two years. Replace damaged shaving
heads right away.
Only replace the shaving heads with original
RQ32 Philips shaving heads. See also
chapter ‘Ordering accessories’.
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit and pull the shaving head
holder off the shaving unit (Fig. 7).
3 To unlock the orange retaining ring,
turn it in the direction of the arrows
indicated in and on the retaining
ring (Fig. 11).
4 Lift the retaining ring out of the
shaving head holder (Fig. 12).
5 Remove the shaving heads and place
new ones in the shaving head holder.
Make sure the two wings of the shaving
heads t exactly into the recesses.
6 Place the retaining ring back onto the
shaving head holder (1). To reattach
the retaining ring, turn it against the
direction of the arrows indicated in
and on the retaining ring (2) (Fig. 18).
Note: Make sure the retaining ring is xed
properly. The four wings of the retaining ring
have to be located exactly under the recesses
of the shaving head holder (Fig. 19).
7 Reattach the shaving head holder to
the shaving unit (‘click’) (Fig. 9).
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Ordering accessories
To purchase accessories for this
appliance, please visit our online shop at
www.shop.philips.com/service. If the
online shop is not available in your country,
go to your Philips dealer or a Philips service
centre. If you have any difculties obtaining
accessories for your appliance, please
contact the Philips Consumer Care Centre
in your country. You nd its contact details
in the worldwide guarantee leaet.
The following accessories are available:
- RQ32 Philips shaving heads
- HQ110 Philips Shaving Head Cleaning
Spray
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 21).
- The built-in rechargeable shaver battery
contains substances that may pollute the
environment. Always remove the battery
before you discard or hand in the shaver
at an ofcial collection point. Dispose
of the battery at an ofcial collection
point for batteries. If you have trouble
removing the battery, you can also take
the appliance to a Philips service centre.
The staff of this centre will remove the
battery for you and will dispose of it in
an environmentally safe way (Fig. 22).
Removing the rechargeable
shaver battery
Only remove the rechargeable battery
when you discard the shaver. Make sure
the rechargeable battery is completely
empty when you remove it.
Be careful, the battery strips are sharp.
1 Undo the screw in the back panel of
the shaver with a screwdriver (1) and
remove the back panel (2) (Fig. 23).
2 Bend the hooks aside and remove the
power unit (Fig. 24).
3 Break the snap hooks (1) and remove
the front panel of the power unit
(2) (Fig. 25).
4 Take out the battery holder (1) and
cut the battery tags with a pair of
cutting pliers (2) (Fig. 26).
5 Remove the rechargeable battery.
Problem Possible
cause
Solution
The shaving
heads are
damaged
or worn.
Replace the
shaving heads
(see chapter
‘Replace-
ment’).
The
rotation
speed of
the shav-
ing heads
is lower
than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The re-
chargeable
battery is
low.
Recharge
the battery.
See chapter
‘Charging’.
The shav-
ing heads
do not
stay in
place.
You did not
x the re-
taining rings
properly.
The retaining
ring is xed
properly
if the four
wings of the
retaining ring
are located
exactly under
the recesses
of the shaving
head holder.
After fully
charg-
ing the
shaver, it
provides
less
than 20
shaving
minutes.
If you have
a heavy
beard, the
shaver may
provide
less than
20 shaving
minutes.
The num-
ber of shav-
ing minutes
may also
vary over
time,
depending
on your
shaving
behaviour,
cleaning
habits and
beard type.
Guarantee and service
If you need service or information or if
you have a problem, please visit the Philips
website at www.philips.com/support or
contact the Philips Consumer Care Centre
in your country. You nd its phone number
in the worldwide guarantee leaet. If there
is no Consumer Care Centre in your
country, go to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact the
Consumer Care Centre in your country.
Problem Possible
cause
Solution
The
shaver
does not
shave as
well as it
used to.
The shaving
heads are
damaged
or worn.
Replace the
shaving heads
(see chapter
‘Replace-
ment’).
The shaving
heads are
dirty.
Clean the
cutters and
guards with
the clean-
ing brush
supplied
(see chapter
‘Cleaning and
maintenance’,
section ‘Extra-
thorough
cleaning
method’).
Problem Possible
cause
Solution
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the clean-
ing brush
supplied
(see chapter
‘Cleaning and
maintenance’,
section ‘Extra-
thorough
cleaning
method’).
The
shaver
does not
work
when I
switch it
on.
The re-
chargeable
battery is
empty.
Switch off
the shaver
and recharge
the battery
(see chapter
‘Charging’).
The tem-
perature of
the shaver
is too high.
In this case,
the shaver
does not
work.
Let the shaver
cool down. As
soon as the
temperature
of the shaver
has dropped
sufciently,
you can
switch on the
shaver again.
The
shaver
does not
work,
even
though
it is con-
nected to
the mains.
The re-
chargeable
battery is
empty.
Switch off
the shaver
and recharge
the battery
(see chapter
‘Charging’).
My skin is
irritated
after
shaving.
Your skin
needs time
to get
used to
the Philips
shaving
system.
Skin irritation
during the
rst 2-3
weeks of use
is possible.
After this
period, the
skin irritation
usually disap-
pears.
- 这款飞利浦产品符合关于电磁场
(EMF) 的相关标准。据目前的科学
证明,如果正确使用并按照本用户
手册中的说明进行操作,本产品是
安全的。
概述
- 电源适配器可将 100-240 伏的电压
转换为 24 伏以下的安全低电压。
基本说明 (图 3)
1 保护盖
2 剃须刀头部件(带剃须刀头支架)
3 剃须刀头支架释放钮
4 开/关滑钮
5 固定环
6 刀片
7 网罩
8 剃须刀头支架
9 清洁刷
10 适配器
11 充电指示灯
12 小插头
充电
电池充满电需要约 10 小时。
充满电的剃须刀可提供多达 20 分钟的
剃须时间。
如果您的胡须非常浓密,则剃须时间
就可能不足 20 分钟。剃须时间还可能
因您的剃须方式、清洁习惯和胡须类
型而异。
“正在充电”指示
- 剃须刀充电时,适配器上的指示灯
会亮起。 (图 4)
充电
切勿在包装中为剃须刀充电。
1 关闭剃须刀。
2 将小插头插入剃须刀。
3 将电源适配器插入电源插座。
, 适配器上的指示灯亮起,表明剃须
刀正在充电。
注意:剃须刀充满电后,适配器上的指
示灯不会改变颜色及熄灭。
使用剃须刀
注意:此剃须刀可接电使用。但是,
当电池电量耗尽时,其无法接电操作。
在此情况下,先至少为剃须刀充电
1小时。
简体中文
简介
感谢您的惠顾,欢迎光临飞利浦!为了
您能充分享受飞利浦提供的支持,请
在 www.philips.com/welcome 上注册
您的产品。
注意事项
使用本产品之前,请仔细阅读本使用说
明书,并妥善保管以备日后参考。
危险
- 确保电源适配器干燥。 (图 1)
- 电源适配器内含有一个变压器。
切勿自行更换插头,否则将导致严
重后果。
- 电源软线不能更换,如果软线损
坏,此器具(电源适配器)应废弃。
警告
- 本产品不打算由肢体不健全、感觉
或精神上有障碍或缺乏相关经验和
知识的人(包括儿童)使用,除非
有负责他们安全的人对他们使用本
产品进行监督或指导。
- 应照看好儿童,确保他们不玩耍本
产品。
- 清洁产品时要小心使用热水。切记
先检查水温是否太高,以防手被
烫伤。
注意
- 必须在 5 摄氏度至 35 摄氏度之间
的温度下充电、使用和存放剃须刀。
- 旅行携带时,应确保将保护盖放在
剃须刀上,以保护剃须刀头。
- 剃须刀及附件不能用洗碗机清洗。
- 切勿使用温度高于 80°C 的热水冲
洗剃须刀。
- 只能使用随附的适配器。
- 如果剃须刀或适配器已损坏,
请勿再使用。
- 如果适配器已损坏,则务必更换原
装型号适配器,以免发生危险。
- 冲洗产品时,水可能从剃须刀底部
的插口漏出。这是正常的,而且没
有危险,因为所有的电子线路都密
封在剃须刀内的一个密封壳内。
符合标准
- 本剃须刀符合国际认可的安全标
准,可放心在自来水龙头下清洗。
符号注释:适合用在打开的水龙头
下进行清洗。 (图 2)
6 小心甩干多余的水,然后使剃须刀
头支架干燥。
不要用毛巾或纸巾擦干剃须刀头支架,
因为这样可能会损坏剃须刀头。
7 将剃须刀头支架重新装回剃须刀
头部件中(可听到“咔哒”一声)
。(图9)
超彻底清洁方法 
1 关闭剃须刀。
2 按剃须刀头部件(1)上的的释放钮
并将剃须刀头支架从剃须刀头部件
(2)中抽离。(图10)
3 要打开橙色固定环,请按其内和其
上所示的箭头方向转动固定环。
(图11)
4 将固定环从剃须刀头支架中提起并
取出。(图12)
5 取下刀片和网罩。(图13)
注意:不要同时清洁多组刀片和网罩,
因为它们都是相互匹配的。如果不小心
将刀片装到了错误的网罩上,则需要数
周时间才能恢复产品的最佳剃须性能。
6 用随附的清洁刷清洁刀片。(图14)
7 清洁网罩的内侧。(图15)
8 清洁后,将网罩装回剃须刀头支
架。确保两个翼状物正好插入剃须
刀头支架的凹槽。(图16)
9 将刀片重新装回至网罩,刀片柄朝
下。(图17)
10将固定环置于剃须刀头支架(1)
上。要重新安装固定环,请逆着其
内和其上所示的箭头方向转动固定
环(2)。(图18)
注意:确保正确固定固定环。固定环的
四个翼状物必须正好位于剃须刀头支架
的凹槽下方。(图19)
11 将剃须刀头支架重新装回剃须刀头
部件中(可听到“咔哒”一声)。
(图9)
注意:如果剃须刀头部件关闭不畅,请
检查剃须刀头的放置是否正确,固定环
是否正确固定。
剃须
皮肤适应期
前几次剃须可能不会带给您预期效果,
并且您的皮肤可能会受到轻度刺激。
这是正常的。您的皮肤和胡须需要时间
适应新的剃须系统。
建议您在 3 周时间内定期剃须(至少每
周 3 次),以便让您的皮肤适应新的剃
须刀。在此期间,请仅使用新的电动剃
须刀,不要使用其他剃须方法。如果您
使用不同的剃须方法,那么您的皮肤会
更难适应新的剃须系统。
1 向上移动开/关滑钮以打开剃须刀。
2 将剃须刀头在皮肤上移动。作直线
和迂回动作。(图5)
3 向下移动开/关滑钮以关闭剃须刀。
4 每次剃须后均应清洁剃须刀
(见“清洁和保养”一章)。
清洁和保养
切勿使用钢丝绒、研磨性清洁剂或腐蚀
性液体(例如汽油或丙酮)来清洁剃须
刀及其附件。
- 每次剃须后均应清洁剃须刀。
- 经常使用飞利浦剃须刀头清洁喷雾
剂 (HQ110) 清洁剃须刀头,以获得
最佳剃须效果。
- 您可以用湿布清洁剃须刀的外侧。
切勿用布清洁剃须刀头部件。
清洁剃毛刀头部件
使用热水时一定要小心。切记先检查水
温是否太高,以防烫手。
1 关闭剃须刀。
2 在热水龙头下冲洗一会儿剃须刀头
部件。(图6)
注意:您也可以使用随附的清洁刷清洁
剃须刀头部件。
3 在水龙头下冲洗本产品后,将其竖
直握住10-15秒钟,使水从底部流
出。
4 按剃须刀头部件(1)上的的释放钮
并将剃须刀头支架从剃须刀头部件
(2)中抽离。(图7)
5 将剃须刀头支架在热水龙头下冲洗
30秒。(图8)
注意:您也可以使用随附的清洁刷清洁
剃须刀头支架。
保修与服务
如果您需要服务或信息,或者有任何疑
问,请访问飞利浦网站:
www.philips.com/support。您也可与您
所在国家/地区的飞利浦客户服务中心
联系(可从全球保修卡中找到其电话号
码)。如果您所在的国家/地区没有飞利
浦客户服务中心,请与当地的飞利浦经
销商联系。
保修条款
由于剃须刀头(刀片和网罩)属于易磨
损物品,因此不在国际保修条款的涵盖
范围之列。
故障种类和处理方法
本章归纳了使用本产品时最常见的一些
问题。如果您无法根据以下信息解决问
题,请访问 www.philips.com/support
查阅常见问题列表,或联系您所在国家/
地区的客户服务中心。
问题 可能的
原因
解决方法
剃须刀
的剃须
效果没
有以前
好。
剃须刀头
已损坏或
磨损。
更换剃须刀头
(见“更换”
一章)。
剃须刀头
很脏。
用随附的清洁
刷清洁刀片和
网罩(请参
阅“清洁和
保养”一章
中的“彻底清
洁方法”部
分)。
过长的胡
须堵塞了
剃须刀
头。
用随附的清洁
刷清洁刀片和
网罩(请参
阅“清洁和
保养”一章
中的“彻底清
洁方法”部
分)。
订购附件
要购买本产品的附件,请访问我们
的在线商城 www.shop.philips.com/
service。如果您的国家/地区没有在线
商城,请联系您的飞利浦经销商或飞利
浦服务中心。如果您购买产品的附件有
困难,请联系您所在国家/地区的飞利浦
客户服务中心。可在全球保修卡中找到
其详细联系信息。
可选配以下附件:
- RQ32 飞利浦剃须刀头
- HQ110 飞利浦剃须刀头清洁喷雾剂
环保
- 弃置产品时,请不要将其与一般生
活垃圾堆放在一起;应将其交给官
方指定的回收点。这样做有利于环
保。 (图 21)
- 内置充电电池含有可能会污染环境
的物质。丢弃剃须刀时,一定要将
电池取出,或将剃须刀送到官方指
定的回收站。到官方指定的电池回
收站处理电池。如果您在取出电池
时遇到问题,您也可以将剃须刀送
至飞利浦维修中心。维修中心的员
工会帮您取出电池,并以环保的方
式处理它。 (图 22)
卸下剃须刀的充电电池
只有在丢弃剃须刀时才可取下充电电
池。请确保在取下充电电池时电量已完
全耗尽。
注意,电池带非常锋利。
1 用螺丝刀(1)拧下剃须刀后面板中
的螺钉,并卸下后面板(2)。
(图23)
2 将钩子向外掰,取出电源部件。
(图24)
3 脱开安全钩(1),取下电源部件(2)
的前面板。(图25)
4 取出电池舱(1),用一把钢丝钳(2)
剪下电池标签。(图26)
5 卸下充电电池。
存储 
注意:确保剃须刀头部件是干燥的,
然后再存放剃须刀。
1 使用后请盖上剃须刀保护盖,以防
止损坏剃须刀头并避免其内积聚灰
尘。(图20)
更换
为获得最佳剃须效果,建议您每隔两年
更换一次剃须刀头部件。损坏的剃须刀
头应立即更换。
剃须刀头仅可使用原装 RQ32 飞利浦
剃须刀头进行更换。另请参阅“订购附
件”一章。
1 关闭剃须刀。
2 按剃须刀头部件上的释放钮并将
剃须刀头支架从剃须刀头部件中抽
离。(图7)
3 要打开橙色固定环,请按其内和其
上所示的箭头方向转动固定环。
(图11)
4 将固定环从剃须刀头支架中提起并
取出。(图12)
5 取下剃须刀头,将新刀头放入剃须
刀头部件。
确保剃须刀头的两个翼状物正好插入
凹槽。
6 将固定环置于剃须刀头支架(1)
上。要重新安装固定环,请逆着其
内和其上所示的箭头方向转动固定
环(2)。(图18)
注意:确保正确固定固定环。固定环的
四个翼状物必须正好位于剃须刀头支架
的凹槽下方。(图19)
7 将剃须刀头支架重新装回剃须刀
头部件中(可听到“咔哒”一声)
。(图9)
注意:如果剃须刀头部件关闭不畅,
请检查剃须刀头的放置是否正确,
固定环是否正确固定。
问题 可能的
原因
解决方法
启动剃
须刀
后,剃
须刀无
法工
作。
充电电池
的电量已
耗尽。
关闭剃须刀并
为电池充电
(请参阅“充
电”一章)。
剃须刀的
温度过
高。此
时,剃须
刀无法工
作。
让剃须刀冷
却。一旦剃须
刀降到足够低
的温度,便可
重新打开剃须
刀。
剃须刀
不工
作,即
使已连
接电
源。
充电电池
的电量已
耗尽。
关闭剃须刀并
为电池充电
(请参阅“充
电”一章)。
我在剃
须后出
现皮肤
过敏。
您的皮肤
需要一定
的时间来
适应飞利
浦剃须
刀。
在前 2-3 周的
使用过程中,
可能会出现皮
肤过敏。在此
之后,皮肤
过敏通常会消
失。
剃须刀头
已损坏或
磨损。
更换剃须刀头
(见“更换”
一章)。
剃须刀
头的转
速比平
时慢。
剃须刀头
中积聚了
太多的灰
尘。
清洁剃须刀
头。请参阅“
清洁和保养”
一章。
充电电池
的电量不
足。
给电池充电。
见“充电”一
章。
剃须刀
头未固
定到
位。
未正确固
定固定
环。
固定环的四个
翼状物正好位
于剃须刀头支
架的凹槽下方
时,才能固定
好固定环。
问题 可能的
原因
解决方法
完全充
电后,
剃须刀
提供的
剃须时
间不足
20 分
钟。
如果您的
胡须非常
浓密,则
剃须时间
就可能不
足 20 分
钟。剃须
时间还可
能因您的
剃须方
式、清洁
习惯和胡
须类型而
异。
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Philips RQ310/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル

他の言語で