INSTRUCTION MANUAL
WINGSPAN : 1600mm
RADIO CONTROLLED ELECTRIC POWERED THERMAL GLIDER
STRATUS 1600
For Intermediate
&
Advanced Flyers.
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No. 10013
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
RADIO PREPARATION
ASSEMBLY
PARTS LIST
OPERATING YOUR MODEL SAFELY
2
3
3
4 11
11
11 12
This radio control model is not a toy.
•The product you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under
various national / state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local
solid waste officials for details in your area for recycling options or proper disposal.
SAFETY PRECAUTIONS
THE FINEST RADIO CONTROL MODELS
R
Ni-Cd
© 2001 KYOSHO
INDEX
Before commencing assembly, please read these instructions thoroughly.
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of children’s reach!
Take enough safety precautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
•
REQUIRED FOR OPERATION (Not included in kit!)
TOOLS REQUIRED
Sharp Hobby Knife
Awl
REAMER
Scissors
Phillips Screwdriver (L.M.S)
AAAAAAAA
2
2
Ni-Cd Battery
Ni-Cd Battery
3
Charger
(Choose one that matches your Ni-Cd Battery)
Charger
No. 72506
Multi Charger III
No.71721
8.4V-600mAh AE
Ni-Cd Battery
1
Minimum 2 channel radio
(Micro servos prefered)
AA-size Batteries
(Transmitter)
Electronic speed controller for
airplanes.
8.4V-600 mAh AE
Ni-Cd BATTERYRechargeable
KYOSHO CORPORATION JAPANNo.71721
R
THE FINEST RADIO CONTROL MODELS
No. 90511
Auto cut-off relay
Sky Victory 210
( No Brake Function )
electronic speed conloller
No. 90801
CAUTION: Handle tools carefully!
Wire Cutters
CAUTION: Only use a radio for Airplanes!
(Any other radio is prohibited!)
TAPER REAMER
No.80311
4
Epoxy A
Epoxy B
Epoxy Glue
Glue
This model will require a minimum 3-channel radio control (with 2 standard servos
and 1 electric speed controller) for aircraft, or a minimum 2-channel radio control
(with 2 standard servos and 1 autocut off relay).
If you use a 2channel radio with an auto-cut-off relay,no brake action is available so
the propeller will not fold after motor cut-off occurs.
5
Extension Cord
This model is designed for 2ch operation with Auto-cut-off or
3ch with electronic speed controller.
Tape
13mm
28mm
29.7mm
Servo
96443
Foam Tape (5mm)
for mounting the receiver &
electronic speed controller
Drill
8.4V
III
210
extension cord for rudder
1 extension cord for elevator
RADIO PREPARATION
1
BEFORE YOU BEGIN
Check all parts. If you find any defective or missing parts,
contact your local dealer or our Kyosho Distributor.
2
3
Read through the manual before you begin, so you
will have an overall idea of what to do.
Symbols used throughout the instruction manual,
2mm
Do not overlook
this symbol!
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
Pay close attention here!
Apply epoxy glue.
Must be purchased
separately!
Assemble left and right sides
the same way.
Ensure smooth non-binding
movement while assembling.
Install batteries. (Transmitter)
Extend the antenna. (Transmitter)
Connect the Ni-Cd battery.
Extend the antenna. (Receiver)
Center the trims.
Switch on. (Transmitter)
Switch on. (Receiver)
Make sure the servos are working.
Switch off. (Receiver)
Switch off. (Transmitter)
Retract the antenna. (Transmitter)
1
2
3
4
5
6
7
8
9
10
11
Set up the radio control system as indicated below.
START
FINISH
7
1
2
4
3
6
8
5
A new Ni-Cd battery must be charged before it is used.
Refer to the charger instruction manual for charging.
NiCd
BATTERY
DC12V
CHARGER
1
2
Install the
grommets to the
servo as shown.
low setting
Use an iron covered with a cloth!
Start at low setting. Increase the set--
ting if necessary. If it is too high, you
may damage the film.
with cover (cloth)
The pre-covered film on ARF kits may wrin-kle due to
variations of temperature. Smooth out as explained
right.
Cut off excess.
Tentatively tighten.
3
Warning!
1
2
3
4
5
6
7
8
9
10
11
ページを読み込んでいます...
2mm
Drill holes with the specified
diameter (here: 2mm).
Apply epoxy glue.
Cut off shaded portion.
Pay close attention here!
5
Fuselage
Wing
4
3mm
Mark
C
C
Mark
A/2
A
3mm
6
Wing
3.2mm
A A'
A=A'
5
3mm
3.2mm
2 mm
14 mm
2 mm
4 mm
14 mm 30 mm
2.2 mm
2mm
8
7
9
Drill holes with the specified
diameter (here: 2mm).
Apply epoxy glue.
Pay close attention here!
6
Fuselage
Fuselage
Fuselage
3mm
Blind Nut
1
Warning!
Do not disregard this symbol!
Warning!
Make sure to glue securely. If not
properly glued, a faliure in flight
may occur.
2mm
H
G EF
ID
J
J
H G EFI
D
A A'
A=A'
4mm
20 mm
Use in step 9
.
H
I
J
G
F
E
D
2mm
9
Must be purchased separately!
Ensure smooth non-binding
movement while assembling.
Cut off shaded portion.
Pay close attention here!
Servo
Tail Surfaces
10
11
A
B
C C'
B'
A'
C=C'
A=A'
B=B'
Included with the servo.
Elevator Servo
Rudder Servo
Be rough by sandpaper
on setting surfase.
Top
Trim the holes in the servo
trey to fit your servos.
Warning!
Make sure to glue securely. If not
properly glued, a faliure in flight
may occur.
Do not disregard this symbol!
Warning!
Linkage
12
Elevator Rod
Rudder Rod
5 mm
10 mm
5 mm
7
13
14
2mm
Drill holes with the specified
diameter (here: 2mm).
Ensure smooth non-binding
movement while assembling.
Cut off excess.
Cut off shaded portion.
Pay close attention here!
8
Linkage
Linkage
2 x 10mm
2 x 10mm
2mm
14 m
m
4 mm
8 mm
5.5 mm
15
Linkage
16
Linkage
3 mm
10 m
m
3.5 mm
3.5 mm
2mm
2 x 10mm
Screw
2 x 10mm
Screw
2
Included with the servo.
Elevator Servo
Rudder Servo
Solder
Solder
Elevator Rod
Rudder Rod
Rudder Rod
Rudder
Warning!
Make sure to solder securely. If not properly
solderd, a faliure in flight may occur.
Warning!
Make sure to solder securely. If not
properly solderd, a faliure in flight
may occur.
2
2mm
2mm
Drill holes with the specified
diameter (here: 2mm).
Apply epoxy glue.
Pay close attention here!
Fuselage
17
18
Canopy
Decal
Do not disregard this symbol!
Warning!
2 x 6mm TP
Screw
19
Foam Tape
Electronic Speed Controller or
Auto cut-off relay.
Battery
Velcro Tape
Velcro Tape
Receiver
Must be purchased separately!
2
9
Tentatively tighten,
2 x 6mm
2 x 6mm
2 x 6mm
0.8mm
4mm
2mm
1.6mm
1.6mm
Warning!
Make sure to glue securely. If not properly
glued, a faliure in flight may occur.
1 1.5 mm
Securely install and fasten the propeller.
If coming off while rotating, there is a high risk
of serious injury!
Warning!
Assemble in the specified order.
1
2
3
2mm
ページを読み込んでいます...
CG / Angles
Decals
RUDDER
CG
ELEVATOR
Do not fly before confirming the correct location of the CG.If the CG is incorrect, you lose control of your airplane which
leads to accidents!
Adjust the travel of each control surface to the values in the diagrams. These values fit
general flight capabilities. Readjust according to your needs and flight level.
For the correct placement of decals, please refer to the box top.
Warning!
8mm
8mm
25mm
25mm
55 ~ 60mm
11
24
23
PARTS
No. Part Names Quantity
10013-01
10013-02
1
x 1 Set
70110
1
800
800
1500
No. Part Names
:FOR JAPANESE MARKET ONLY.
Quantity
10013-03
Canopy
Plywood parts
Decale
Motor Set
90100
x 1
1000
Folding Propeller Set (D6xP3)
90100-01
2
800
Folding Propeller (D6xP3)
1000
200
Warning!
Do not overlook this symbol!
Warning!
First-time fliers should seek advice for hints in pre-flight adjustments and assembly from experienced fliers.
Be reminded that flying a badly assembled or badly adjusted aircraft is very dangerous!
In the beginning, first-time fliers should always be assisted by an experienced flier and never fly alone!
Due to the wing being very light-weight sudden maneuvers and violent aerobatics can cause it to break
while in flight. This will result in a crash and possibily cause harm to the operator or nearby persons. Under
no circumstances should violent aerobatics be attempted with this model airplane.
200
00
0 0 2 1 0 4 4 7 2 7 1
1 6 8 0
0 0 2 1 0 4
4 7 2 7 1
1 6 8 0
1,400
200
80
1,680
(1)
(2)
(2)
(3)
(4)
(1)
10013
Before Flying Flying After Flying
Before flying your airplane, ensure
the airfield is spacious enough.
Always fly it outdoors in safe areas
with no debris or obstacles!
For proper radio handling, refer to
its explanations.
Ensure the spinner and propeller
are securely installed.
If the airplane begins to operate by
itself, somebody else is on your fre-
quency. Do not attempt to operate
it under such condition for you may
lose of control of it.
Fully extend
the antenna
(transmitter).
Move the sticks on your transmitter
to ensure that all controls move
according to your inputs and the
way you adjusted them.
Do not fly your airplane on days
with strong winds or side winds.
Always land your airplane into the
wind.
Ensure the main wing is securely
installed.
Check the radio batteries.
Switch off the transmitter.
Unplug the Ni-Cd battery.
Cautions for Safety
Do not allow watching people to get too
close to a rotating propeller.
Disuse defective propellers as well as
deformed spinners.
Batteries and chargers become
hot. Do not allow flammable
materials to come in contact with
them.
Never try to modify Ni-Cd battery.
This is very dangerous.
OPERATING YOUR MODEL SAFELY
Beware of spinning propellers!
Switch on the transmitter.
Only use genuine KYOSHO parts.
Launch your airplane by hand into
the wind.
Plug in the Ni-Cd battery.
If your airplane does not function cor-
rectly, land it at once and find out the
reason.
Unplug the Ni-Cd battery when not
in use.
Proper maintenance extends the
life of your airplane.
Do not dispose of used Ni-Cd
batteries, return them to the shop.
Do not dispose of Ni-Cd batteries
in a fire. They will explode and
release harmful materials.
Beware of spinning propellers! With
some electronic speed controllers,
the electric motor (propeller) start
spinning as soon as the electronic
speed controller is connected.
PRINTED IN CHINA62150103-1
R
THE FINEST RADIO CONTROL MODELS
OFF
ON
ON
WIND
WIND
OFF ON
Battery
OFF
Battery
BATTE
RY
Battery
Battery
Warning!
Warning!
Batter
y
243-0034 153
TEL.046-229-4115
10 00 18 00
/