时刻美 1583 手表操作使用说明书
功能简介:
功能介绍:
时间及日期的设定:
闹铃时间的设定:
闹铃响闹:
第二时间功能及设定:
倒计时功能:
倒计时的设定:
秒表功能:
Digits LCD Display Display Hour ,Minute ,Second ,Month ,Day, Year and Week
Dual time display (display both local and second time);
12/24hr display;
Daily Alarm and Chime hourly
1/100 second Chronograph with split functions
Countdown function,to:23:59:59;
Dual time;
3 second EL backlight
Year setting;(range: 2000~2049)
,
;
Operation Manual
At any state ,press A key EL backlight for 3s .
Press B key function successively:time mode→Daily Alarm→Dual time→Timer→Chronograph;
In the time mode, press and hold C key to time setting state and "Second" flashing
Press B key to select Settings:second time minutes year month day;(note:in any mode of this interface,
press A key to convert 12/24 hours)
Press D key to adjust the setting items, press and hold D key to rapidly adjust;
After setting, press C key exit setting mode.
→ → → → →
Press A key to start: daily alarm hourly chime daily alarm and hourly chime;
Press C key to enter alarm setting mode, “hour ” flashing;
Press B key to select the setting items: hour minute month day;
Press D key to adjust the setting items, press and hold D key to rapidly adjust;
After setting, press C key exit setting mode.
Note: default to daily alarm!When set month - day, it means the designated date time ring!
→ →
→ → →
When Alarm is ON, the alarm prompt lasts for 10 seconds. Press any key to stop the alarm prompt.
press C key to enter the second time setting "hour" flashing;
Press B key to select setting items :hour→minute;
Press D key to adjust the setting items, press and hold D key to rapidly adjust;
After setting, press C key to exit setting mode.
The measurement range of this table is 23 hours, 59 minutes and 59 seconds.
Press C key to enter the setting mode, “hour ” flashing;
Press B key to select Settings: hour minute → second;(in the setting interface, press A key to turn on or off
AUTO AUTO loop)
When the AUTO cycle function is turned on, the mode will be set before the automatic cycle after the timer is
completed. Enter the timer setting item and press A to close the AUTO; (Press D in timer mode to pause timer
and then press C to enter the setting item)
Press D key to adjust the setting items, press and hold D key to rapidly adjust;
After setting, press C key to exit setting mode;
Timer alarm sounds for about 10 seconds ,press any key to stop the alarm;
When stop the alarm, display the timer setting .
When the timer is stop midway, press A key to return to the setting.
→
Press D key to start dual time mode, When stop, press C key to zero.
During the dual timer, press A key to turn on SPL function, display “SPL” on the screen.press A key to return to
the dual timer again.
When reach the maximum (23 hours, 59 minutes, 59.99 seconds), continue to restart the stopwatch timing from 0;
Note: ABCD four key to hold down at the same time,will restore factory settings! As shown in the following figure:
SKMEI 1583 Operation Manual
FEATURES:
FUNCTION:
TIME/DATE SETTING:
Daily Alarm Mode:
The alarm ring:
Dual time function and setting:
Timer Mode:
Chronograph:
计时功能显示:时、分、秒、日、月和星期;
可双时钟显示(同时显示本地和第二时间);
12/24小时显示;
闹铃,整点报时功能;
秒表有1/100秒,分段计时功能;
倒计时功能,最大值:23:59:59;
两地时间;
3秒背光;
年份设置;(范围:2000~2049)
功能选择
在任何功能画面显示时,按A键可点亮背光3秒。
在时间模式,按B键依次转换功能:时间模式→闹铃模式→第二时间模式→倒计时模式→秒表模式;
在时间模式,按C键进入时间设置并“秒”闪烁;
按B键依次选择设置项:秒→时→分→年份→月→日:(注:此界面任意模式下按A键转换12/24小时制)
按D键调整设置项的值,长按D键有快调功能;
设置完毕后,按C键退出设置模式。
在闹铃模式,按A键依次开启:闹铃响闹→整点报时→闹铃响闹和整点报时;
在闹铃模式,按C键进入闹铃设置并“时”闪烁;
按B键依次选择设置项:时→分→月→日;
按D键调整设置项的值,长按D键有快调功能;
设置完毕后,按C键退出设定画面。
注:默认为每天闹铃!当设定了月→日,就表示指定日期时间响闹!
到达闹铃时间时,响闹提示10秒,按任意键都可停止闹响提示。
在第二时间模式,按C键进入第二时间设置并“时”闪烁;
按B键依次选择设置项:时→分;
按D键调整设置项的值,长按D键有快调功能;
设置完毕后,按C键退出设置模式。
本表的测量范围是23小时59分59秒;
在倒计时模式,按C键进入倒计时设置并“时”闪烁;
按B键依次选择设置项:时→分→秒;(在此设置界面按A键开启或关闭AUTO自动循环功能)
当开启AUTO自动循环功能时,倒计时完成后将自动循环之前设置值,可进入倒计时设置项按A键关闭AUTO;(在倒计时模
式按D键暂停倒计时然后按C键进入设置项)
按D键调整设置项的值,长按D键有快调功能;
设置完毕后,按C键退出设置模式;
倒计时结束,10秒响闹提醒,按任意键停止响闹;
倒计时停止响闹,显示倒计时设置值;
当中途暂停倒计时,按A键可回到设置值。
A(LIGHT D(START)
B(MODE) C(RESET)
)
在秒表模式,短按D键开启跑秒计时,在跑表停止计时状态,按A键清零数据。
在跑表计时状态,按A键开启SPL 功能,界面上会显示SPL字样,跑秒功能还在继续运行再次按下A键回到计时器。
跑表到达最大值(23小时59分59.99秒)时,继续由0重新开始跑表计时;
备注:ABCD四健同时按住将显示全显并恢复出厂设置!如下图所示:
A(LIGHT D(START)
B(MODE) C(RESET)
)