Tesla Gen2 インストールガイド

WALL CONNECTOR, J1772, 4OA SINGLE

PHASE INSTALLATION MANUAL

Approved Markets: North America, Japan, Taiwan

CONECTOR DE PARED, J1772, 4OA

MONOFÁSICO MANUAL DE INSTALACIÓN

Mercados Autorizados: Norteamérica, Japón, Taiwan

CONNECTEUR MURAL, J1772, 40 A MONOPHASÉ

MANUEL D'INSTALLATION

Marchés approuvés : Amérique du Nord, Japon, Taïwan

ウォールコネクター、J1772、40 A 単相

取り付けマニュアル

承認済のマーケット：北米、日本、台湾

壁掛式充電座，J1772，4OA 單相

安裝手冊

核准銷售地區：北美地區、日本、台灣

WALL CONNECTOR, J1772, 4OA SINGLE

PHASE INSTALLATION MANUAL

Approved Markets: North America, Japan, Taiwan

About this Manual......................2

Product Speciﬁcations..............................................2

Communications Regulations.................................2

Errors or Inaccuracies................................................2

Copyrights and Trademarks....................................2

Safety Information..................... 3

Important Safety Instructions................................ 3

Warnings.........................................................................3

Cautions..........................................................................3

Notes................................................................................4

Speciﬁcations............................. 5

Features.......................................6

Circuit Ratings..............................................................6

Self-Monitoring and Recovery................................6

Power Outages.............................................................6

Load Sharing.................................................................6

Planning Your Installation.........7

Minimum Requirements............................................7

120V Above Ground................................................... 7

Ground Connection.................................................... 7

240V Single-Phase..................................................... 7

208V 3-Phase Wye-Connected.............................8

240V Three-Phase Delta-Connected.................. 8

Determine the Circuit Breaker

Requirements................................................................8

Choose the Best Location for the Wall

Connector...................................................................... 9

Installation Considerations...................................... 9

Check the Box Contents..........10

Step-by-Step Installation

Instructions................................12

Tools and Materials Required................................ 12

Overview of Installation Steps..............................12

Install the Low Proﬁle

Bracket for Rear

or Bottom Entry Wiring...........................................13

Install the Top Entry Bracket for Rear or

Top Entry Wiring........................................................14

Prepare for Installation............................................ 15

C

onnect the Wiring...................................................16

Set the Operating Current......................................18

Secure the Cover and Power Up..........................19

Troubleshooting........................21

Reset..............................................................................24

Questions?...................................................................25

Appendix A: Testing for

Proper Operation.....................26

Appendix B: Optional

Connection for Load

Sharing...................................... 27

Daisy Chaining Multiple Wall Connectors........27

Example of the Communication Wiring...........28

Other Load Sharing Behaviors............................ 28

Contents

Product Speciﬁcations

All speciﬁcations and descriptions contained

in this document are veriﬁed to be accurate at

the time of printing. However, because

continuous improvement is a goal at Tesla, we

reserve the right to make product

modiﬁcations at any time.

Communications Regulations

This device complies with Part 15 of the FCC

rules and Industry Canada license-exempt RSS

standard(s). Operation is subject to the

following two conditions: (1) This device may

not cause harmful interference and (2) this

device must accept any interference received,

including interference that may cause

undesired operation.

Important: Changes or modiﬁcations to

this product not authorized by Tesla

could void the FCC compliance.

Errors or Inaccuracies

T

o communicate any inaccuracies or

omissions, or to provide general feedback or

suggestions regarding the quality of this

manual, send an email to:

ownersmanualfeedback@tesla.com

Copyrights and Trademarks

All inf

ormation in this document is subject to

copyright and other intellectual property

rights of Tesla, Inc. and its licensors. This

material may not be modiﬁed, reproduced or

copied, in whole or in part, without the prior

written permission of Tesla, Inc. and its

licensors. Additional information is available

upon request. The following are trademarks or

registered trademarks of Tesla, Inc. in the

United States and other countries:

All other trademarks contained in this

document are the property of their respective

owners and their use herein does not imply

sponsorship or endorsement of their products

or services. The unauthorized use of any

trademark displayed in this document or on

the vehicle is strictly prohibited.

About this Manual

2

Important Safety Instructions

This document contains important instructions

and warnings that must be followed when

installing and maintaining the Wall Connector.

Warnings

Warning: Read all the instructions before

using this product.

Warning: This device should be

supervised when used around children.

Warning: The Wall Connector must be

grounded .

Warning: Do not install or use the Wall

Connector near ﬂammable, explosive,

harsh, or combustible materials,

chemicals, or vapors.

Warning: Use the Wall Connector only

within the speciﬁed operating

parameters.

Warning: Stop using and do not use the

Wall Connector if it is defective, appears

cracked, frayed, broken, or otherwise

damaged, or fails to operate.

Warning: Do not attempt to disassemble,

repair, tamper with, or modify the Wall

Connector. The Wall Connector is not user

serviceable. Contact Tesla for any repairs

or modiﬁcation.

Warning: When transporting the Wall

Connector, handle with care. Do not

subject it to strong force or impact or

pull, twist, tangle, drag, or step on the

Wall Connector, to prevent damage to it

or any components.

Warning: Do not touch the Wall

Connector’s end terminals with ﬁngers or

sharp metallic objects, such as wire, tools,

or needles.

Warning: Do not f

orcefully fold or apply

pressure to any part of the Wall

Connector or damage it with sharp

objects.

Warning: Do not insert f

oreign objects

into any part of the Wall Connector.

Warning: Use of the Wall Connector may

aect or impair the operation of any

medical or implantable electronic devices,

such as an implantable cardiac

pacemaker or an implantable cardioverter

deﬁbrillator. Check with your electronic

device manufacturer concerning the

eects that charging may have on such

electronic devices before using the Wall

Connector.

Cautions

Caution: Do not use private power

generators as a power source for

charging.

Caution: Incorrect installation and testing

of the Wall Connector could potentially

damage either the vehicle’s Battery

and/or the Wall Connector itself. Any

resulting damage is excluded from the

New Vehicle Limited Warranty and the

Charging Equipment Limited Warranty.

Caution: Do not operate the Wall

Connector in temperatures outside its

operating range of -22°F to 122°F (-30°C

to +50°C).

Safety Information

Safety Information 3

Notes

Note: Ensure that the Wall Connector’s

charging cable is positioned so it will not be

stepped on, driven over, tripped on, or

subjected to damage or stress.

Note: Do not use cleaning solvents to clean

any of the Wall Connector’s components. The

outside of the Wall Connector, the charging

cable, and the connector end of the charging

cable should be periodically wiped with a

clean, dry cloth to remove accumulation of

dirt and dust.

Note: Be careful not to damage the circuit

boards or components during installation.

Safety Information

4

The maximum power rating for the Wall Connector is 11 kW or 40A at 240V AC single-phase

power.

Description Speciﬁcations

Voltage and Wiring

208V or 240V AC single-phase: L1, L2, and earth

Current

Maximum output: 40A

Frequency 50 to 60 Hz

Cable Length 24' (7.4 m)

Wall Connector Dimensions Height: 15.0" (380 mm)

Width: 6.3" (160 mm)

Depth: 5.5" (140 mm)

Top Entry Bracket Dimensions Height: 10.8" (275 mm)

Width: 5.1 " (130 mm)

Depth: 2.0" (50 mm)

Weight (including bracket) 17 lb (7.5 kg)

Operating Temperature -22°F to 122°F (-30°C to 50°C)

Storage Temperature -40°F to 185°F (-40°C to 85°C)

Enclosure Rating Type 3R

Agency Approvals cULus listed for United States and Canada under ﬁle

number E354307, FCC Part 15.

Ventilation Not Required

Speciﬁcations

Speciﬁcations 5

Circuit Ratings

Use a single-phase circuit breaker rated for

50A single phase to obtain the highest power

output.

In certain installation locations, this level of

power isn’t readily available. Therefore, the

Wall Connector has an automatic load

management feature that allows the output

current to be adjusted to any circuit breaker

ranging from 15A to 50A (refer to Set the

Operating Current on page 18).

Note: Actual amperage draw will depend on

the on-board charger of the vehicle. Contact

Tesla if you have questions about the on-

board charger of a speciﬁc vehicle.

Self-Monit

oring and Recovery

The Wall Connector has a ground monitoring

circuit that continuously checks for the

presence of a safe ground connection and

automatically recovers from faults. Manual

testing and resetting is not required.

Temporary problems such as ground faults or

utility power surges are overcome

automatically. If a residual current fault occurs

that interrupts charging, the Wall Connector

automatically tries to clear the fault and re-

attempt charging.

If the problem is immediately sensed a second

time, the Wall Connector waits 15 minutes

before trying to charge. This process repeats 4

times and if all attempts are unsuccessful,

power is removed and no further attempts are

made. In this case, you will see a red error light

on the front panel (refer to Troubleshooting

on page 21). It is recommended that when

you see a red error light, you power o the

W

all Connector by switching o the upstream

cir

cuit breaker, and then power it back on

again.

The Wall Connector can alternatively be reset

when a red error light is encountered using

the RESET button (refer to Reset on page

24).

Power Outages

If a po

wer outage occurs, the Wall Connector

automatically resumes charging when power

is restored. If the charging cable is plugged

into the vehicle when power is restored, the

lights blink and the unit does not energize the

charging cable for approximately 15 seconds

to three minutes. This prevents the utility grid

from experiencing a large surge when power is

restored and allows vehicles to begin drawing

current at random times, rather than all at

once.

Load Sharing

Up to 4 Wall Connectors can be wired to a

single circuit, and with built-in automatic load

management, vehicle owners can easily

charge multiple vehicles at home (refer to

Appendix B: Optional Connection for Load

Sharing on page 27).

Features

6

Minimum Requirements

Installation of the Wall Connector requires that

you:

• Calculate the existing electrical load to

determine the maximum operating

current.

• Calculate the distance to ensure minimal

voltage drop.

• Obtain any necessary permits from the

local authority that has jurisdiction and

conﬁrm that the follow-up inspection has

been scheduled by an electrician after the

installation is complete.

• Use only copper conductors.

• Use conductors that are sized in

accordance with local wiring regulations.

The selected cable must be able to sustain

periods of constant load of up to the

maximum amperage selected by the

electrician.

• Use a circuit breaker.

Note: Consult with an electrician to ensure

that the installation meets local regulations.

120V Above Ground

Warning: T

he Wall Connector is a single-

phase device. Do not connect all three

phases of a three-phase feed.

Warning: Bef

ore installing the Wall

Connector, identify the type of utility

service connection available on site. If you

are unsure about the type of connection

available at the service panel, consult an

electrician, or contact Tesla for assistance.

Caution: T

he two phases used must each

measure 120V to neutral. Earth ground

must be connected to neutral at only one

point, usually at the breaker panel.

Caution: If a 240V thr

ee-phase feed is

from a Delta-connected secondary, the

leg used must have a center tap. This

center tap must be grounded. Only the

two phases on either side of the center-

tapped leg can be used.

Only three wires are connected, but care must

be tak

en that the service transformer

secondary connection is deﬁnitely known, and

that the three wires from the main circuit

breaker panel are correctly connected and

labeled.

Note: The L1, L2, and ground outputs labeled

on the illustrations correspond to the inputs

on the Wall Connector.

Ground Connection

Always connect the Neutral at the service to

Earth Ground. Ground fault protection is not

possible unless the Neutral (center tap on the

service transformer) is connected to an Earth

Ground. If ground is not provided by the

electrical service, you must install a grounding

stake nearby. the grounding stake must be

connected to the ground bar in the main

breaker panel, and Neutral connected to

Ground at that point.

240V Single-Phase

L2

L1

120V

GND

240V

NEUTRAL

(NOT USED)

Note: Illustrations in this document are for

demonstration purposes only.

Planning Your Installation

Planning Your Installation 7

208V 3-Phase Wye-Connected

With a Wye-connected secondary, any two of

the legs can be used to provide 208V to the

Wall Connector. For example, L1 and L2, or L1

and L3, or L2 and L3. The two used phases

must each measure 120V to neutral.

Note: A current-carrying neutral is not

required.

120V 208V

120V

L1

NEUTRAL

(NOT USED)

L3 (NOT USED)

L2

GND

Caution: The unused leg (L3 in the

illustration) must remain open. Do not

connect to a neutral bar, or to earth

ground.

Caution: The center point of the three

phases (normally used as neutral) must

be grounded to earth at only one point.

This is usually at the breaker panel.

240V Three-Phase Delta-

Connected

With the delta connection, one leg must be

center tapped, and only the two phases on

either side of the center tap can be used. The

two used phases must each measure 120V to

neutral.

Consult the transformer manufacturer’s

literature to verify that the single leg can

supply the required power.

Note: The Wall Connector’s contactor closes

only if it detects the presence of an earth

ground wire connected to a neutral point on

the transformer secondary.

L1

L2

GND

120V

240V

L3 (NOT USED)

NEUTRAL

(NOT USED)

Caution: The third line (L3 in the

illustration) of the delta is 208V, with

respect to neutral, and is sometimes

referred to as a “stinger.” Do not use this

third line.

Caution: Do not use a three-phase delta-

connected transformer secondary

without a center tap on one leg. No

neutral point is available for the required

earth ground connection.

Determine the Circuit Breaker

Requirements

To determine the type of upstream circuit

breaker you need, examine the distribution

panel or circuit breaker box to identify the

amperage available at the installation site.

Planning Your Installation

8

The Wall Connector has an internal rotary

switch that allows you to adjust its operating

current (refer to Set the Operating Current on

page 18). The circuit breaker should be

rated for the continuous current of 40A.

Choose the Best Location for the

Wall Connector

Determine the parking location of the vehicle

to ensure that the charge cable reaches the

charge port. The Wall Connector should be

located:

• In an enclosed garage, typically on the

vehicle's charge port side.

• In a well-ventilated area. Avoid installation

in an enclosed box, or adjacent to hot

appliances.

• 4 ft (1.2 m) above the ﬂoor.

• 8 in (190 mm) from any obstructions to

allow for cable looping.

Note: The Wall Connector is approved for

outdoor use, but it is not designed for

complete immersion in liquid. Protection from

rain is recommended but not required.

Installation Considerations

Three methods are available to install the Wall

Connector. The location of the conduit and

type of wiring determine which installation

method to follow:

• If the conduit runs along the ﬂoor or low

on the wall, use the bottom entry

conﬁguration.

• If the conduit comes from inside the wall,

use the r

ear entry conﬁguration.

• If the conduit comes from the ceiling, or if

the service wiring is thicker than 6 AWG,

use the top entry conﬁguration. The top

entry br

acket has an optional rear-facing

knockout that allows thicker service wiring

to enter from the top or rear.

Note: Throughout the manual, “conduit” is

used as the standard term for the protective

tubing that houses the service wiring. In

regions where conduit is not used (Europe for

example), a cable comprised of service wiring

enclosed in a protective jacket may be

substituted for conduit if allowed by local

regulations.

Here are some additional guidelines:

•

Conduit openings are sized for 1" (25 mm)

conduit.

• Conduit needs to meet all local

regulations.

• Use an appropriate circuit breaker.

• Use a UL approved conduit connector to

ensure proper seal.

• When installing wire thicker than 6 AWG,

use the top entry installation.

Bottom or Rear Entry

Top Entry or Optional Rear Entry

Planning Your Installation

Planning Your Installation 9

The shipping box contains parts for all installation methods, as well as this manual. If any parts are

damaged or missing, contact Tesla (refer to Questions? on page 25).

Note: Not shown is the supplied cardboard template.

Item Description (Quantity)

1 Wall Connector

2 Top entry bracket*

3 Low proﬁle bracket **

4 Low proﬁle bracket screws (2) **

5 Bottom or rear entry power conduit plug

6 Bottom or rear entry signal conduit plug

7 Top entry signal conduit plug* (pre-installed on the top entry bracket)

8 Top entry power conduit plug* (pre-installed on the top entry bracket)

9 Bottom conduit sealing gasket*

10 Top bracket-to-housing screw covers (2)

11 Bottom bracket-to-housing screw covers (2)

Check the Box Contents

10

Item Description (Quantity)

12 Bottom bracket-to-housing screws (2)

13 Top bracket-to-housing screws (2)

14 Top entry bracket mounting screws (2)*

* Items used in only top entry installations.

** Items used in only bottom or rear entry installations.

Check the Box Contents

Check the Box Contents 11

Tools and Materials Required

Before installing the Wall Connector, gather

the following tools and materials:

• Pencil or marker

• Hole punch (optional, to push through

cardboard template)

• Wire stripper

• Voltmeter or digital multimeter (to

measure AC voltage at the installation

site)

• Phillips screwdriver

• Small ﬂathead screwdriver

• Large ﬂathead screwdriver (optional, to

remove plastic knock-outs)

• T20 security pin Torx driver (included)

• T10 Torx driver (included)

• M20 and M32 cable glands (also known as

sealing hubs)

• Wiring (use 18 AWG twisted pair

communication cable at a maximum of 49

ft (15 m) between Wall Connectors)

• Level

• Machine drill

• Torque driver (for terminal block

connections)

Overview of Installation Steps

Warning: After you run service wiring to

the installation site, install the appropriate

upstream circuit breaker, TURN OFF AND

VERIFY POWER IS OFF BEFORE

CONTINUING.

Then follow these steps to install the Wall

Connector:

• Install the Low Proﬁle Bracket for Rear or

Bottom Entry Wiring on page 13

• Install the Top Entry Bracket for Rear or

Top Entry Wiring on page 14

• Prepare for Installation on page 15

• Connect the Wiring on page 16

• Set the Operating Current on page 18

• Secure the Cover and Power Up on page

19

Step-by-Step Installation Instructions

12

Install the Low Proﬁle Bracket for

Rear or Bottom Entry Wiring

Use the low proﬁle bracket, shown below, to

wire the Wall Connector from the rear or

bottom.

1. Use the low proﬁle bracket as a guide to

mark the location on the wall for the

mounting screws.

• Use a level to ensure that the marks

are perfectly vertical.

• Space the holes 4.5" (114 mm) apart.

• For U.S.A. installations, position the

br

acket so that the Wall Connector is

located at a maximum of 60" (150 cm)

from ﬂoor level. The minimum height

is 18" (45 cm) if mounting indoors,

and 48" (122 cm) if mounting

out

doors.

• If using the rear entry conduit, use at

least one set of the edge mounting

holes so that the conduit does not

interfere with the wall stud.

• If using the bottom entry conduit, use

the two center mounting holes.

Note: Ensure that the minimum and

maximum height of the bracket is carefully

selected. It should be installed out of the

way of any reasonably foreseeable

impacts.

2. Attach the bracket using fasteners that

are appropriate for the type of wall

material, drilling pilot holes if necessary.

Use the supplied screws only if mounting

the bracket directly to a wooden stud. If

mounting to another type of wall (hollow,

masonry, etc.), use fasteners that are long

enough to securely anchor the Wall

Connector and can hold at least 80 lb (36

kg).

Step-by-Step Installation Instructions

Step-by-Step Installation Instructions 13

Install the Top Entry Bracket for

Rear or Top Entry Wiring

The top entry bracket enables you to route the

service wiring into the Wall Connector

enclosure from the top of the enclosure, as

shown below.

1. Use the cardboard template and a level as

a guide to mark the location on the wall

for the mounting screws.

• Use a level to ensure that the marks

are perfectly vertical.

• Space the holes 6.1" (155 mm) apart.

• Position the bracket so that the Wall

Connector is located at a maximum of

60" (150 cm) from ﬂoor level. The

minimum height is 18" (45 cm) if

mounting indoors, and 48" (122 cm) if

mounting out

doors.

Note: Ensure that the minimum and

maximum height of the bracket is carefully

selected. It should be installed out of the

way of any reasonably foreseeable

impacts.

2. (Optional) There are two additional

mounting holes. To use these holes, use a

ﬂat-head

screwdriver to knock-out the

plastic that is closing the holes. These

holes are spaced 2.75" (70 mm) apart.

3. Attach the bracket using fasteners that

are appropriate for the type of wall

material, drilling pilot holes if necessary.

Use the supplied screws only if mounting

the bracket directly to a wooden stud. If

mounting to another type of wall (hollow,

masonry, etc.), use fasteners that are long

enough to securely anchor the Wall

Connector and can hold at least 80 lb (36

kg).

Step-by-Step Installation Instructions

14

Prepare for Installation

Follow these instructions to remove the cover

and route the service wiring into the Wall

Connector.

1. Use a T10 Torx driver to remove the screw

at the bottom of the outer cover. Carefully

disengage the snaps on the sides and top

using a ﬂathead screwdriver and

completely remove the cover. Save the

screw and cover for reassembly.

2. Use a T20 security pin T

orx driver to

remove the six screws on the sealing

cover. Carefully remove the sealing cover

and disconnect the ribbon cable. Save the

screws and cover for reassembly.

Caution: Do not allow the sealing

cover to hang from the ribbon cable.

Doing so can damage the ribbon

cable or its connectors.

3. For top entry conﬁguration, install the

wiring to the terminal block in the top

entry bracket as shown in Connect the

Wiring on page 16, then return to this

section and proceed to the next step. For

back or bottom entry conﬁgurations, skip

to the next step.

4. Place and hold the Wall Connector on the

bracket, ensuring that all four mounting

tabs are properly aligned.

5. Use a T20 Torx driver to install the two

top housing mounting screws. Push the

cosmetic screw covers into place.

6. Use a T20 Torx driver to install the two

bottom housing mounting screws. Push

the cosmetic screw covers into place.

Step-by-Step Installation Instructions

Step-by-Step Installation Instructions 15

Connect the Wiring

Note: Consult with your local electrician or

refer to your local code for proper wire sizing

appropriate for the currents in your Wall

Connector.

Note: It is the installer's responsibility to

identify whether additional grounding is

required to ensure that local regulations are

met. Grounding must be installed at the power

source and not at the cable entry to the Wall

Connector.

Warning: Do not connect service wiring

until you have read and fully understand

the concepts described in this section. If

you are uncertain about the type of

power available at the service panel,

consult an electrician, or contact Tesla for

assistance.

1. Turn o the power.

Warning: RISK OF ELECTRIC SHOCK!

Before continuing, use a voltmeter to

ensure the power is o by conﬁrming

that NO VOLTAGE is present at the

service wiring or terminals.

2. For top entry installation, pull the service

wiring into the top entry bracket or the

Wall Connector. Use a 1" (25 mm) cable

gland to seal the power conduit or cable.

Note: The meaning of wiring colors might

vary from country to country. Follow all

applicable national and local regulations

concerning wiring color codes.

The following illustration shows an

example of the wiring for the top entry

bracket.

The following illustration shows an

e

xample of the wiring for the low proﬁle

bracket.

3. S

trip the service wires going to the

terminal block on the top entry bracket

3/4" (18 mm). Ferrules are recommended.

Step-by-Step Installation Instructions

16

ページを読み込んでいます...

Tesla Gen2 インストールガイド

関連論文

その他の書類