DCF813
DCF815
2
English (original instructions) 03
简体中文 12
繁體中文 20
한국어
28
Copyright DeWALT
1
Figure 1
Figure 2
k
f
b
a
g
e
f
g
h
i
j
DCF813
b
a
g
e
f
g
h
c
DCF815
d
2
Figure 3
Figure 4
Figure 5
f
c
d
c
d
e
j
i
ENGLISH
3
12V MAX CORDLESS IMPACT WRENCH
DCF813
12V MAX CORDLESS IMPACT DRIVER
DCF815
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
DCF813 DCF815
Voltage V 10.8V (12V Max) 10.8V (12V Max)
Battery Type Li-Ion Li-Ion
No load speed min
-1
0–2450 0–2450
Max torque Nm 130 107
Tool holder 3/8" 1/4"
(9.5 mm) (6.35 mm)
Weight (without battery pack) kg 0.8 0.8
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
Batteries Chargers/Charge Times (Minutes)
Cat # V
DC
Ah
Weight
kg
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB124 10.8V(12V Max) 3.0 0.25 45 140 90 70 45 45 45 90
DCB125 10.8V(12V Max) 1.3 0.20 22 60 40 30 22 X 22 40
DCB127 10.8V(12V Max) 2.0 0.20 30 90 60 50 30 X 30 60
ENGLISH
4
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
ENGLISH
5
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Impact Wrenches/Drivers
• Hold power tool by insulated gripping
surfaces when performing an operation
where the fastener may contact hidden
wiring. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool
“live” and could give the operator an electric
shock.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
DATE CODE POSITION
The date code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
Example:
2020 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instruc tions
for the DCB105, DCB107 and DCB112 battery
chargers.
• Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, grinding dust, metal chips,
steel wool, aluminum foil, or any buildup
of metallic particles should be kept away
from charger cavities. Always unplug the
charger from the power supply when
there is no battery pack in the cavity.
Unplug charger before attempting to
clean.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
ENGLISH
6
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
• Do not operate charger with damaged cord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service centre.
• Do not disassemble charger; take it to an
authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on
standard 220-240V household electrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB105, DCB107 and DCB112 chargers
accept 10.8 V (12V Max) Li-Ion batteries.
These chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger (k) into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack (f) into the charger.
The red (charging) light will blink continuously
indicating that the charging process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.
Charging Process
Refer the table below for the state of charge of the
battery pack.
State of charge - DCB105
charging – – – –
fully charged –––––––––––
hot/cold pack delay –– – –– –
replace battery pack •••••••••••
State of charge - DCB107 and DCB112
charging –– –– –– –– ––
fully charged ––––––––––––––––––––
hot/cold pack delay –– –– –– –––––––
Hot/Cold Pack Delay
DCB105
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
DCB107 AND DCB112
When the charger detects a battery that is hot, it
automatically delays charging until the battery has
cooled.
ENGLISH
7
When the charger detects a battery that is cold, it
automatically delays charging until the battery has
warmed.
The red light will continue to blink, but a yellow
indicator light will be illuminated during this
operation. Once the battery has cooled, the yellow
light will turn off and the charger will resume the
charging procedure.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
• Never force battery pack into charger. Do
not modify battery pack in any way to fit
into a non-compatible charger as battery
pack may rupture causing serious personal
injury.
• Charge the battery packs only in DeWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40 ˚C (105 ˚F) (such as
outside sheds or metal buildings in summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged, do
not insert into charger. Do not crush,
drop or damage battery pack. Do not
use a battery pack or charger that has
received a sharp blow, been dropped,
run over or damaged in any way (i.e.,
pierced with a nail, hit with a hammer,
stepped on). Damaged battery packs
should be returned to service centre for
recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• If battery contents come into contact with
the skin, immediately wash area with mild
soap and water. If battery liquid gets into the
eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Pack
BATTERY TYPE
The DCF813 and DCF815 operate on 10.8 V (12V
Max) battery packs.
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
ENGLISH
8
2. For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
Read instruction manual before use.
100%
Battery charging.
100%
Battery charged.
Battery defective.
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with DeWALT battery packs,
others may burst, causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4 ˚C and 40 ˚C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack.
See Technical Data for charging time.
Only for indoor use.
Package Contents
The package contains:
1 Cordless impact driver or impact wrench
1 Charger
2 Battery packs
1 Impact rated screwdriver bit (DCF815)
1 Kitbox (D2 model)
1 Instruction manual
NOTE: Battery packs and chargers are not included
with N-models.
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Trigger switch
b. Forward/reverse button
c. Chuck collar (DCF815)
d. 1/4" (6.35 mm) hex quick-release chuck
(DCF815)
e. Battery release button
f. Battery pack
g. Worklight
h. Main handle
i. Anvil (DCF813)
j. Hog ring (DCF813)
INTENDED USE
The impact driver and impact wrench are designed
for professional impact fastening applications. The
impact function makes this tool particularly useful for
driving fasteners in wood, metal and concrete.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
This impact driver and impact wrench are
professional power tools. DO NOT let children come
into contact with the tool. Supervision is required
when inexperienced operators use this tool.
ENGLISH
9
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with IEC 60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organisation.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1.5 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fig. 3)
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
NOTE: Make sure your battery pack (f) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack with the rails inside the
handle.
2. Slide it firmly into place until you hear the lock
snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release button (e) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
Proper Hand Position (fig. 1, 5)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (h).
Variable Speed Trigger Switch (fig. 1)
To turn the tool on, squeeze the trigger switch (a). To
turn the tool off, release the trigger switch. Your tool
is equipped with a brake. The chuck will stop when
the trigger switch is fully released.
The variable speed switch enables you to start
the application at a slow speed. The further you
squeeze the trigger, the faster the tool will operate.
For maximum tool life, use variable speed only for
starting holes or fasteners.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
ENGLISH
10
Forward/Reverse Control Button
(fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool. The center
position of the control button locks the tool in the off
position. When changing the position of the control
button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up.
This is normal and does not indicate a problem.
Worklights (fig. 1)
There are three worklights (g) located around the
anvil (d, i). The worklights will be activated when the
trigger switch is squeezed.
NOTE: The worklights are for lighting the immediate
work surface and are not intended to be used as a
flashlight.
Anvil with Hog Ring (fig. 1, 4)
DCF813
CAUTION: Use only impact sockets.
Non-impact sockets may break and
cause a hazardous condition. Inspect
sock et prior to use to ensure that it
con tains no cracks.
Place the forward/reverse button (b) in the locked
off (center) position or remove battery pack before
changing accessories.
To install a socket on the hog ring anvil, firmly push
socket onto the anvil (i). The hog ring (j) compresses
to allow the socket to slide on. After the socket
is installed, the hog ring applies pressure to help
provide socket retention.
To remove a socket, grasp the socket and firmly pull
it off.
Quick-Release Chuck (fig. 1, 4)
DCF815
NOTE: The chuck accepts 1/4" (6.35mm) hex
accessories and 1" (25.4mm) bit tips only. Using 1"
(25.4mm) bits allows better access in tight spaces.
Place the forward/reverse button (b) in the locked
off (center) position or remove battery pack before
changing accessories.
To install an accessory, push accessory to fully
insert into chuck (d). The chuck collar (c) does not
need to be pulled up to lock accessory in place.
To remove an accessory, pull the chuck collar
away from the front of the tool. Remove the
accessory and release the collar.
Usage
Your impact tool generates the following output
torque:
Cat # Ft.-Lbs. In.-Lbs. Nm
DCF813 96 1150 130
DCF815 79 950 107
CAUTION: Ensure fastener and/or
system will withstand the level of torque
generated by the tool. Excessive torque
may cause breakage and possible
personal injury.
1. Place the socket on the fastener head. Keep
the tool pointed straight at the fastener.
2. Press switch to start operation. Always check
torque with a torque wrench, as the fastening
torque is affected by many factors including the
following:
• Voltage: Low voltage, due to a nearly
discharged battery, will reduce fastening
torque.
• Socket size: Failure to use the correct
socket size will cause a reduction in fastening
torque.
• Bolt Size: Larger bolt diameters generally
require higher fastening torque. Fastening
torque will also vary according to length,
grade, and torque coefficient.
• Bolt: Ensure that all threads are free of rust
and other debris to allow proper fastening
torque.
• Material: The type of material and surface
finish of the material will affect fastening
torque.
• Fastening Time: Longer fasten ing time
results in increased fastening torque. Using
a longer fastening time than recom mended
could cause the fasteners to be overstressed,
stripped or damaged.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
ENGLISH
11
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT, recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DeWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and
packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Li-Ion cells are recyclable. Take them to your
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
简体中文
12
12V MAX 锂电充电式冲击扳手
DCF813
12V MAX 锂电充电式冲击起子
DCF815
恭喜！
恭喜您选择了得伟工具。凭借多年的产品开发和创新经验，得伟已经成为专业电动工具用户最可靠的合
作伙伴之一。
技术参数
DCF813 DCF815
电压 V 10.8V (12V Max) 10.8V (12V Max)
电池类型 锂离子 锂离子
空载速度 min
-1
0–2450 0–2450
最大扭矩 Nm 130 107
工具手柄 3/8" 1/4"
(9.5 mm) (6.35 mm)
重量（不含电池组） kg 0.8 0.8
定义：安全指引
下列定义解释了各警示词的严重程度。请仔细阅读
本手册，并注意这些警示符号。
危险：表示存在紧急危险情况，如果
不加以避免，将导致死亡或严重伤害。
警告：表示存在潜在危险情况，如果
不加以避免，可能导致死亡或严重伤
害。
警示：表示存在潜在危险情况，如果不
加以避免，可能导致轻度或中度伤害。
注意：表示不涉及人身伤害的情况，
如果不加以避免，可能导致财产损失。
表示存在触电危险。
表示存在火灾危险。
电池 充电器
/
充电时间（分钟）
目录号 伏特
直流
安时
重量
（千克）
DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119
DCB124 10.8V(12V Max) 3.0 0.25 45 140 90 70 45 45 45 90
DCB125 10.8V(12V Max) 1.3 0.20 22 60 40 30 22 X 22 40
DCB127 10.8V(12V Max) 2.0 0.20 30 90 60 50 30 X 30 60
警告：为降低伤害风险，请阅读使用
手册。
电动工具一般安全警告
警告！请阅读所有安全警告和指示说
明。如不遵守以下任何警告和指示说
明，可能导致触电、火灾和/或严重伤
害。
请保存所有警告和指示说明，
以备将来查阅。
以下所有警告中的“电动工具”一词是指电源驱动
（有线）电动工具，或者电池驱动（无线）电动工
具。
1) 工作场地安全
a)
保持工作区域清洁、通亮。杂乱或阴暗的地
方容易引发事故。
b)
不要在易爆环境中操作电动工具，如有易燃
液体、气体或粉尘的环境。电动工具产生的
火花会点燃粉尘或气体。
简体中文
13
c)
让儿童和旁观者离开后才操纵电动工具。干
扰可能会导致您控制不当。
2) 电气安全
a)
电动工具插头必须与同规格的插座搭配。禁
止以任何方式改装插头。需接地的电动工具
不能使用任何转换插头。未经改装的插头与
相配的插座将减少触电风险。
b)
避免人体接触接地表面，如管道、散热片、
炉灶和冰箱等。如果您的身体接地，会增加
触电危险。
c)
请勿将电动工具暴露在雨中或潮湿环境中。
水进入电动工具会增加触电危险。
d)
切勿滥用电线。切勿使用电线搬运、拉动电
动工具或拔下插头。保持电线远离热源、
油、锐边或运动部件。受损或缠绕的电线会
增加触电危险。
e)
在户外操作电动工具时，请使用适合户外使
用的延长线。适合户外使用的电线会减少触
电的危险。
f)
如果必须在潮湿的地方操作电动工具，请使
用漏电保护器
(RCD)
。使用漏电保护器可减
少触电的危险。
3) 人身安全
a)
保持警觉。当操作电动工具时，请留意所从
事的操作并保持清醒。切勿在疲倦，或受到
药物、酒精或治疗的影响下使用电动工具。
操作电动工具时注意力分散会导致严重人身
伤害。
b)
使用个人防护装备。始终佩戴护目镜。防护
装备，例如适当条件下使用的防尘面具、防
滑安全鞋、安全帽或听力保护等装备将能减
少人身伤害。
c)
避免意外启动。在连接电源和/或电池组之
前，以及拿起或搬动工具之前，请确保开关
处于关闭位置。搬动电动工具时把手指放在
开关上，或开关处于接通状态时插入插头均
可引发危险。
d)
在电动工具接通之前，取下所有调节钥匙或
扳手。连接在电动工具旋转零件上的扳手或
调节钥匙会导致人身伤害。
e)
手不要伸得太长。时刻注意脚下和身体平
衡。这样在意外情况下才能更好地控制电动
工具。
f)
着装适当。切勿穿宽松衣服或佩戴首饰。让
您的头发、衣服和手套远离运动部件。宽松
衣服、首饰或长发可能会卷入运动部件中。
g)
如果提供了与排屑装置和集尘设备连接用的
装置，请确保这些装置连接完好且使用得
当。使用这些装置可减少碎屑引起的危险。
4) 电动工具的使用和注意事项
a)
禁止强制使用电动工具。根据用途选用适当
的电动工具。选用适当的设计额定值的电动
工具会使您工作更有效、更安全。
b)
禁止使用开关不能打开和关闭的电动工具。
任何不能用开关控制的电动工具都很危险，
必须进行修理。
c)
进行任何调节、更换附件或存储电动工具之
前，请将电动工具和电源插头或电池组断
开。这种防护性措施将减少电动工具突然启
动的危险。
d)
将闲置的电动工具贮存在儿童所及范围之
外，并且不要让不熟悉电动工具或对本说明
书不了解的人操作电动工具。让未经训练的
用户操作电动工具是很危险的。
e)
保养电动工具。检查运动部件是否有任何安
装偏差或卡住、零件是否破损，以及是否有
其他可能影响电动工具操作的情况。如有损
坏，必须在使用前对电动工具进行维修。许
多事故就是由于电动工具维护不良所导致。
f)
保持刀具锋利和清洁。妥善保养和切割锋利
的刀具可使操作时不容易卡住，且更容易控
制。
g)
请按照使用说明书，并考虑作业条件和具体
执行的工作来使用电动工具、附件和工具刀
头等。将电动工具用于非预期操作用途可能
会导致危险情况。
5) 电池工具使用和注意事项
a)
只能使用制造商指定的充电器为电池充电。
使用适用于其他类型电池组的充电器充电可
能会引发火灾。
b)
电动工具只能配备明确指定的电池组。使用
任何其他电池组可能会造成人身伤害和引发
火灾。
c)
电池组放置不用时，要远离回形针、硬币、
钥匙、钉子、螺钉以及其他可连通电池两极
的金属物品。电池短路可能会导致灼伤或火
灾。
d)
滥用电池的情况下，电池可能会喷射出液
体，请避免接触该液体。如果不小心接触
到液体，请用清水冲洗。如果眼睛接触到液
体，请寻求医疗救护。从电池喷出的液体可
能会刺激皮肤或灼伤。
6) 维修
a)
本电动工具必须由合格的维修人员且仅采用
相同的替换备件进行维修。这将确保电动工
具的安全性能。
冲击扳手/起子的附加安全细则
•
操作过程中紧固件可能接触隐藏的电线时，请
握住工具的绝缘表面。紧固件接触带电导线可
简体中文
14
能使电动工具外露的金属部件带电，从而导致
操作人员触电。
剩余风险
尽管遵守了相关的安全法规并采用了安全装备，某
些剩余风险仍然是无法避免的。这些风险包括：
– 听力损伤。
– 飞散颗粒造成的人身伤害风险。
– 操作过程中附件加热而产生的烧伤危险。
– 长时间使用引起的人身伤害。
工具上的标识
工具上有下列标志：
使用前请阅读使用手册。
日期代码位置
连接工具和电池之间的外壳表面印有日期代码，日
期代码包括制造年份。
例如：
2020 XX XX
制造年份
针对所有电池充电器的重要安全
说明
请妥善保存这些说明：本手册包含有关
DCB105
，
DCB107 和
DCB112
电池充电器的重要安全和操
作说明。
•
在使用充电器之前，请先阅读所有指示以及充
电器、电池组和使用电池组的产品上的警示标
记。
警告：触电危险。禁止任何液体渗入充
电器，否则会引起触电。
警示：灼伤危险。为减低人身伤害风
险，只可以使用得 伟 充电式电池充
电。使用其他类型的电池可能会引起
爆裂，并导致人身伤害和损害。
警示：监督儿童以确保他们不把设备当
玩具。
注意：在某些情况下，充电器连接到电
源后，充电器触头可能会被异物导致短
路。导电的异物，包括但不限于研磨粉
尘、金属屑、钢丝绒、铝箔纸或任何由
金属粒子组成的物件，必须要远离充电
器范围。充电器内没有电池组时，请断
开充电器与电源的连接。清洗前，务必
拔掉充电器。
•
请勿使用本手册指定的充电器以外的其他任何
充电器为电池组充电。充电器和电池组都是专
门设计的，互相配合使用。
•
除了为得伟充电式电池充电以外，这些充电器
都不能用于其他任何用途。否则，可能会导致
火灾、电击或触电。
•
请勿将充电器暴露于雨中或雪中。
•
断开充电器时应拔下插头，切勿拉拽电线。这
将减少电源插头和电源线损坏的风险。
•
确保电源线布置在不易踩踏、踢绊、拉扯或会
受到损害或压力的位置。
•
非绝对必要条件下禁止使用延长线。延长线使
用不当可能会导致火灾、电击或触电。
•
请勿将任何物件放在充电器上面，或是把充电
器放在可能会堵住通风槽的柔软表面，导致充
电器的内部过热。充电器应远离所有热源。充
电器外壳顶端和底端具有通风槽。
•
禁止使用电源线或插头已损坏的充电器，请立
即将其更换。
•
如果充电器受到重击、掉落或出现其他损坏情
况，请勿使用充电器。请将已损坏的充电器送
到授权的服务维修中心。
•
请勿自行拆卸充电器。请将需要检修或修理的
充电器送到授权服务维修中心。重装不正确可
能会引起触电、电击或火灾的危险。
•
已损坏的电源线必须立即交由制造商、服务代
理或类似的合格人员进行更换以防止安全隐
患。
•
清洁前，请断开充电器和插座的连接，以减少
触电的危险。仅取出电池不会减少触电风险。
•
切勿将两个充电器连接在一起。
•
充电器是为 220V 的标准家用电源而设计。禁
止在任何其他电压下使用充电器。这条规则不
适用于车载充电器。
请妥善保存这些说明
充电器
DCB105, DCB107 和 DCB112充电器接受10.8 V
(12V Max) 锂离子电池。
这些充电器无需做出任何调整，专为简易操作而
设计。
简体中文
15
充电程序（图 2）
1. 安装电池组之前，将充电器 (k) 插头插入适当
的插座。
2. 将电池组 (f) 放进充电器。红色（充电中）指示
灯将不断闪烁，表示充电过程已经开始。
3.红色灯持续亮起表示充电完成。此时电池组已
完全充电，您可以使用电池组或将电池组留在
充电器上。
注：为了确保锂离子电池的最佳性能和寿命，在首
次使用电池组之前必须将它完全充电。
充电程序
有关电池组的充电状态，请参阅下表。
充电状态-DCB105
充电中 – – – –
已完全充电 –––––––––––
热/冷电池组延迟 –– – –– –
更换电池组 •••••••••••
充电状态-DCB107 和DCB112
充电中 –– –– –– –– ––
已完全充电 ––––––––––––––––––––
热/冷电池组延迟 –– –– –– –––––––
热/冷电池组延迟
DCB105
当充电器检测到电池过热或过冷，它会自动启动
“热/冷电池组延迟”，中止充电直到电池恢复适
当的温度。然后，充电器会自动切换到电池组充
电模式。此功能可确保电池拥有最长的使用寿命。
DCB107 和 DCB112
当充电器检测到电池较热时，会自动延迟充电，直
至电池冷却。
当充电器检测到电池较冷时，会自动延迟充电，直
至电池稍变热。
红色指示灯会继续闪烁，但黄色指示灯在本次操作
过程中会亮起。电池冷却后，黄色指示灯会熄灭，
充电器将恢复充电程序。
XR 锂离子电池工具具有电子保护系统设计，可保
护电池免受过载、过热或过度放电之害。
如果电子保护系统处于运作状态，该工具将自动停
止操作。如果发生这种情况，请将锂离子电池放在
充电器上，直至其完全充电。
仅限锂离子电池组
锂离子电池具有“电子保护系统”设计，可保护电
池免受过载、过热或过度放电之害。
如果电子保护系统处于运作状态，该工具将自动停
止操作。如果发生这种情况，请将锂离子电池放在
充电器上直到完全充电。
针对所有电池组的重要安全说明
在订购替换电池组时，请务必提供产品目录号和电
压。
包装箱内的电池组并未完全充电。使用电池组和充
电器之前，请阅读下列安全说明，然后遵循所述的
充电程序。
请阅读所有说明
•
请勿在易爆环境，如有易燃液体、气体或尘埃
的环境中进行充电或使用电池。在充电器中插
入或从中取出电池时可能会点燃粉尘或气体。
•
切勿强行将电池组插入充电器。请勿以任何方
式改装电池组以在不相容的充电器中使用，否
则电池组可能会破裂，导致严重人身伤害。
•
只可使用得伟充电器为电池充电。
•
请勿喷溅电池组或将其浸泡在水或其他液体中。
•
请勿在温度可能达到或超过
40 ˚C (105 ˚F)
的
地方（如夏天户外的棚子或金属建筑物中）存
储或使用工具和电池组。
警告：禁止以任何理由试图打开电池。
如果电池组外壳破裂或受损，请勿将其
插入充电器。请勿挤压、掉落或损坏电
池组。请勿使用受过重击、掉落、碾压
或以任何其他方式（如被钉子穿破、受
到锤子的重击、踩踏）受损的电池组或
充电器。损坏的电池组应该送回维修中
心进行回收。
警示：放置不用时，将工具侧放在平稳
的表面上，确保不会导致踢绊或掉落的
风险。一些具有大型电池组的工具将直
立于电池组之上，但可能会轻易被撞
倒。
锂离子电池 (Li-Ion) 的特别安全说明
•
即使电池组已经严重受损或已完全耗竭也不可
焚烧处理电池组。电池组会在火中爆炸。锂离
子电池组在燃烧时会释放有毒气体和物质。
•
如果电池液体接触到皮肤，请立即以中性肥皂
和清水冲洗接触范围。如果电池液体不慎进入
眼睛，应睁开眼睛并用清水冲洗至少
15
分钟
或直到刺激感消失。如果需要医疗救助，请告
知医护人员。电池电解质是由液状有机碳酸盐
简体中文
16
和锂盐的混合物组成。
•
电池里的成分可能会导致呼吸道刺激。请转移
至新鲜空气处。如果症状持续存在，请就医。
警告：灼伤危险。电池液体如果接触
到火花或火焰可能会燃烧。
电池组
电池类型
DCF813 和 DCF815 使用 10.8 V (12V Max) 电池
组。
存储建议
1. 最好将电池存放在阴凉、干燥、远离阳光直
射、不会过热或过冷的地方。为了获得最佳的
电池性能和使用寿命，在不使用时请将电池组
存储在室温下。
2. 长期存储时，建议将完全充电的电池组从充电
器取出，存储在阴凉、干燥的地方，以让电池
组达到最佳性能。
注：电池组存储时不能处于电荷完全耗尽的状态。
在使用之前，电池组必须重新充电。
充电器和电池组上的标签
除了在本手册中使用的标志，充电器和电池组的标
签还包括：
使用前请阅读使用手册。
100%
电池充电中。
100%
电池完成充电。
电池受损。
热/冷电池组延迟。
请勿使用导电物体碰触。
禁止对损坏的电池组充电。
只能使用得伟电池组，使用其他电池组
可能会造成电池爆裂，导致人身伤害和
损害。
禁止暴露于水中。
立即更换出现故障的电线。
只在温度介于4 ˚C 至40 ˚C之间充电。
弃置电池组时，请妥善处理以保护我们的
环境。
禁止焚烧电池组。
有关充电时间，请参阅
技术参数
。
只能在室内使用。
包装内容
本产品包装内含有：
1 个锂电充电式冲击起子或冲击扳手
1 个充电器
2 个电池组
1 个额定冲击螺丝起子头(DCF815)
1 个工具箱或工具包
1 本使用手册
注：N 型号不包括电池组和充电器。
•
检查工具、部件或附件是否在运输过程中损坏。
•
操作前，请抽空仔细阅读并掌握本手册。
描述（图 1）
警告：切勿改装电动工具或其任何部
分，否则可能会导致损坏或人身伤害。
a. 触发开关
b. 正转/反转控制按钮
c. 夹具环 (DCF815)
d. 1/4" (6.35 mm) 六角快速释放夹头 (DCF815)
e. 电池释放按钮
f. 电池组
g. 工作灯
h. 主握柄
i. 铁砧(DCF813)
j. 猪环扣(DCF813)
简体中文
17
设计用途
冲击起子和冲击扳手是专为专业冲击锁紧应用而设
计。冲击功能使这个工具非常有用，特别是在木
材、金属和混凝土中钻紧固件这方面。
禁止在潮湿环境中或在有易燃液体或气体的环境中
使用本工具。
冲击起子和冲击扳手是专业的电动工具。请勿让儿
童接触工具。缺乏经验的操作员需要在监督下使用
本工具。
• 本产品不适合体力、感官或智力不足以及缺乏
经验、知识或技能的人员（包括儿童）使用，
除非一旁有能为他们的安全负责的监督人员。
不得在无人监管的情况下让儿童触及本产品。
电气安全
电机只适用一种工作电压。请务必检查电池组的电
压是否和铭牌上的电压一致。另外，确保充电器电
压和主电源的电压一致。
您的得伟充电器符合 IEC 60335 双重绝
缘要求，因此无需使用接地线。
电源线损坏时，必须由得伟服务部门采用专门制备
的电线进行更换。
使用延长电缆
除非绝对必要，否则请勿使用延长线。使用适合您的
充电器电源输入的合格延长电缆（见
技术参数
）。
导线的最小尺寸为 1.5 mm
2
，最大长度为 30 m。
使用电缆卷筒时，请务必拉出所有的电缆。
组装和调整
警告：组装与调整之前，必须取出电池
组。插入或取出电池组之前，请关闭工
具电源。
警告：只使用得伟电池组和充电器。
插入和拆除工具的电池组（图 3）
警告：为了降低严重的人身伤害风险，
调整或拆除/安装配件或附件之前，请
将正转/反转控制按钮置于锁止位置，
或关闭工具电源并取出电池组。
注：确保您的电池组 (f) 已完全充电。
将电池组安装到工具握柄中
1. 将电池组与握柄里的轨道对齐。
2. 将电池组紧紧地滑入握柄，直到听到锁定到位
的声音。
从工具上拆除电池组
1. 按释放按钮 (e) ，并用力将电池组从工具握柄中
拉出。
2. 按本手册充电器部分所述将电池组插入充电器
中。
操作
使用说明
警告：请务必遵守安全说明和适用法
规。
警告：为了降低严重的人身伤害风险，
调整或拆除/安装配件或附件之前，请
将正转/反转控制按钮置于锁止位置，
或关闭工具电源并取出电池组。
正确的手持方式（图 1、5）
警告：为降低严重的人身伤害风险，请
始终使用正确的手持方式，如图所示。
警告：为降低严重的人身伤害风险，
预期有突然反应时务必紧握住工具。
正确的手部位置要求一只手握住主手柄 (h)。
变速触发开关（图 1）
开启工具请按压触发开关 (a)。关闭工具请释放触
发开关。您的工具配备制动器。触发开关完全释放
时夹头将停止运作。
变速开关可以让您缓慢启动应用程序。按压开关
越紧，工具运作越快。为了获得最长的工具使用
寿命，只有在启动钻孔或紧固件时使用变速开关。
注：不建议在变速范围内连续使用工具。否则可能
会损坏开关，因此应尽量避免。
正转/反转控制按钮（图 1）
正转/反转控制按钮 (b) 确定工具方向，也有锁定按钮
的功能。
选择正向旋转时，释放触发开关，按下工具右侧的正
转/反转控制按钮。
选择反向旋转时，按下工具左侧的正转/反转控制按
钮。控制按钮的中心位置会将工具锁定在关闭状态。
改变控制按钮的位置时，确保触发开关处于释放状
态。
注：改变旋转方向后第一次运行该工具时，您可能会
在启动时听到“咔哒声”。这是正常现象，并不代表
出现故障。
工作灯（图 1）
铁砧 (d、i)周围有三盏工作灯 (g)。按压触发开关即
可激活工作灯。
简体中文
18
注：工作灯是用于照亮紧邻的工作表面，不能当做
手电筒使用。
带猪环扣的铁砧（图 1、4）
DCF813
警示：
仅能使用冲击套筒。非冲击型
套筒可能会破裂和导致危险情况。使用
套筒之前，请检查套筒并确保无裂痕。
更换附件之前，将正转/反转控制按钮(b)置于锁止
（中心）位置或拆除电池组。
将套筒安装在猪扣环铁砧上时，请稳固地将套筒推
到铁砧 (i) 上。猪扣环 (j) 压缩以让套筒在其上滑
动。安装套筒之后，猪扣环会施加压力以帮助固定
套筒。
拆除套筒时请抓紧套筒并稳固地将其取下。
快速释放夹头（图 1、4）
DCF815
注：夹头仅适用于 1/4" (6.35mm) 六角附件和 1"
(25.4mm) 起子头。使用 1" (25.4mm) 起子头可以
更好地在狭小的空间操作。
更换附件之前，将正转/反转控制按钮 (b) 置于锁止
（中心）位置或拆除电池组。
安装附件时将附件完全插入到夹头 (d)。锁定附件
时不需要拉起夹具环 (c)。
拆除附件时将夹具环拉离工具前部。拆除附件，松
开夹具环。
用法
您的冲击工具会生成下列输出扭矩：
Cat # Ft.-Lbs. In.-Lbs. Nm
DCF813 96 1150 130
DCF815 79 950 107
警示：确保紧固件和/或系统能够承受
由工具生成的扭矩水平。过大的扭矩
可能会造成破损和人身伤害。
1. 将套筒放在紧固件的头部。保持工具和紧固件
成直线。
2. 按下开关启动操作。由于紧固扭矩受以下因素
影响，请务必使用扭矩扳手检查扭矩：
•
电压：低电压会降低紧固扭矩，原因是电池
快要耗尽。
•
套筒尺寸：如果不使用正确的套筒尺寸，将
使紧固扭矩变小。
•
螺栓尺寸：螺栓直径越大，通常需要的紧固
扭矩也越大。紧固扭矩也将会随着长度、等
级和扭矩系数的变化有所不同。
•
螺栓：确保所有螺纹未生锈，没有其他杂物
以产生适当的紧固扭矩。
•
材料：材料的类型和材料的表面涂层都会影
响紧固扭矩。
•
紧固时间：紧固时间越长，紧固扭矩越大。
如果紧固时间比建议的紧固时间长，可能会
导致紧固件不堪重负、剥离或损坏。
维护
您的得伟电动工具设计精良，可以长期使用，而且
只需最少的维护。要连续获得令人满意的工作效
果，需要进行合适的工具维护和定期清洁。
警告：为了降低严重的人身伤害风险，
调整或拆除/安装配件或附件之前，请
将正转/反转控制按钮置于锁止位置，
或关闭工具电源并取出电池组。
充电器和电池组都不可维修。这些组件内没有可以
维修的零件。
润滑
本电动工具无需另行润滑。
清洁
警告：一旦通风口和周围积聚了可见
的粉尘，请立即用干燥的空气吹走主
机外壳内的粉尘和灰尘。执行此过程
时，需戴上经认可的护目装备和防尘
面具。
警告：切勿使用溶剂或其他烈性化学
制品来清洁工具的非金属部件。这些
化学物质可能会削弱部件使用的材
料。请用抹布蘸温和的肥皂水擦拭。
切勿让任何液体进入工具；切勿让工
具的任何部分在液体中浸泡。
充电器清洁说明
警告：触电危险。清洁前，请把充电
器与交流电源插座断开。可用布或非
金属软刷清除充电器外部的污垢和油
脂。禁止使用水或任何清洁剂。
可选附件
警告：除了得伟提供的附件之外，其
他附件都未经此产品兼容性测试，将
此类附件与本工具一起使用将存在安
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
他の言語で
- English: DeWalt DCF815 User manual