LG G-CS1612W ユーザーガイド

www.lg.com

OWNER'S MANUAL

WASHING

MACHINE

Before beginning installation, read these instructions carefully. This

will simplify installation and ensure that the product is installed

correctly and safely. Leave these instructions near the product after

installation for future reference.

MFL69962024

Rev.00_092217

EN ENGLISH

G-CS1612W

TABLE OF CONTENTS

This manual may contain images or

content different from the model you

purchased.

This manual is subject to revision by the

manufacturer.

SAFETY INSTRUCTIONS .......................................................4

IMPORTANT SAFETY INSTRUCTIONS .................................................... 4

INSTALLATION ......................................................................10

Parts ......................................................................................................... 10

Accessories .............................................................................................. 10

Specifications ............................................................................................11

Installation Place Requirements ............................................................... 12

Unpacking and Removing Transit Bolts .................................................... 13

Using Anti-Slip Sheets (Optional) ............................................................. 14

Wooden Floors (Suspended Floors) ......................................................... 14

Leveling the Appliance .............................................................................. 15

Connecting the Water Supply Hose.......................................................... 15

Installing the Drain Hose .......................................................................... 18

OPERATION ...........................................................................19

Using the Washing Machine ..................................................................... 19

Sorting Laundry ........................................................................................ 20

Adding Cleaning Products ........................................................................ 21

Control Panel ............................................................................................ 23

Programme Table ..................................................................................... 24

Option Programme ................................................................................... 29

Dry ( ) .................................................................................................. 33

SMART FUNCTIONS .............................................................35

Using Smart ThinQ Application ................................................................. 35

Using Smart Diagnosis™ ......................................................................... 37

MAINTENANCE ......................................................................38

Cleaning Your Washing Machine .............................................................. 38

Cleaning the Water Inlet Filter .................................................................. 38

Cleaning the Drain Pump Filter ................................................................ 39

Cleaning the Dispenser Drawer ................................................................ 40

Tub Clean (Optional) ................................................................................ 40

Caution on Freezing During Winter .......................................................... 41

TROUBLESHOOTING ...........................................................43

Diagnosing Problems ............................................................................... 43

Error Messages ........................................................................................ 46

WARRANTY ............................................................................48

4

SAFETY INSTRUCTIONS

EN

The following safety guidelines are intended to prevent

unforeseen risks or damage from unsafe or incorrect operation

of the appliance.

The guidelines are separated into ‘WARNING’ and ‘CAUTION’

as described below.

This symbol is displayed to indicate matters and

operations that can cause risk. Read the part with this

symbol carefully and follow the instructions in order to

avoid risk.

WARNING

This indicates that the failure to follow the instructions can

cause serious injury or death.

CAUTION

This indicates that the failure to follow the instructions can

cause the minor injury or damage to the product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of explosion, re, death, electric shock,

injury or scalding to persons when using this product, follow

basic precautions, including the following:

Children in the Household

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure

that they do not play with the appliance.

5

EN

For use in Europe:

This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

Children of less than 3 years should be kept away unless

continuously supervised.

Installation

•Never attempt to operate the appliance if it is damaged,

malfunctioning, partially disassembled, or has missing or broken

parts, including a damaged cord or plug.

•This appliance should only be transported by two or more people

holding the appliance securely.

•Do not install the appliance in a damp and dusty place. Do not

install or store the appliance in any outdoor area, or any area that

is subject to weathering conditions such as direct sunlight, wind, or

rain or temperatures below freezing.

•Tighten the drain hose to avoid separation.

•If the power cord is damaged or the hole of the socket outlet is

loose, do not use the power cord and contact an authorized service

centre.

•Do not plug multiple socket outlets, an extension power cable or

adapter with this appliance.

6

EN

•This appliance must not be installed behind a lockable door, a

sliding door or a door with a hinge on the opposite side to that of

the appliance, in such a way that a full opening of the appliance

door is restricted.

•This appliance must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by

providing a path of least resistance for electric current.

•This appliance is equipped with a power cord having an equipment-

grounding conductor and a grounding power plug. The power plug

must be plugged into an appropriate socket outlet that is installed

and grounded in accordance with all local codes and ordinances.

•Improper connection of the equipment-grounding conductor can

result in risk of electric shock. Check with a qualied electrician or

service personnel if you are in doubt as to whether the appliance is

properly grounded.

•Do not modify the power plug provided with the appliance. If it

does not t the outlet, have a proper outlet installed by a qualied

electrician.

Operation

•Do not attempt to separate any panels or disassemble the

appliance. Do not apply any sharp objects to the control panel in

order to operate the appliance.

•Do not repair or replace any part of the appliance. All repairs

and servicing must be performed by qualied service personnel

unless specically recommended in this Owner’s Manual. Use only

authorized factory parts.

7

EN

•Do not put animals, such as pets into the appliance.

•Keep the area underneath and around the appliance free of

combustible materials such as lint, paper, rags, chemicals, etc.

•Do not leave the appliance door open. Children may hang on the

door or crawl inside the appliance, causing damage or injury.

•Use new hose or hose-set supplied with the appliance. Reusing old

hoses can cause a water leak and subsequent property damage.

•Do not put in, wash or dry articles that have been cleaned in,

washed in, soaked in, or spotted with combustible or explosive

substances (such as waxes, wax removers, oil, paint, gasoline,

degreasers, drycleaning solvents, kerosene, petrol, spot removers,

turpentine, vegetable oil, cooking oil, acetone, alcohol, etc.).

Improper use can cause re or explosion.

•Never reach into the appliance while it is operating. Wait until the

drum has completely stopped.

•In case of ood, disconnect the power plug and contact the LG

Electronics customer information centre.

•Do not push down the door excessively, when the appliance door is

open.

•Do not touch the door during a high temperature programme.

•Do not use ammable gas and combustible substances (benzene,

gasoline, thinner, petroleum, alcohol, etc.) near the appliance.

•If the drain hose or inlet hose is frozen during winter, use it only

after thawing.

•Keep all washing detergents, softener and bleach away from

children.

8

EN

•Do not touch the power plug or the appliance controls with wet

hands.

•Do not bend the power cable excessively or place a heavy object

on it.

•Do not wash rugs, mats, shoes or pet blankets, or any other items

other than clothes or sheets, in this machine.

•This appliance must only be used for domestic household purposes

and should not be used in mobile applications.

•If there is a gas leakage (isobutane, propane, natural gas, etc.),

do not touch the appliance or power plug and ventilate the area

immediately.

Technical Safety for Using the Dryer

•Do not dry unwashed items in the appliance.

•Items that have been soiled with substances such as cooking

oil, vegetable oil, acetone, alcohol, petroleum, kerosene, spot

removers, turpentine, waxes and wax removers should be washed

in hot water with an extra amount of detergent before being dried in

the appliance.

•Never stop the appliance before the end of the drying cycle unless

all items are quickly removed and spread out so that the heat is

dissipated.

•Items such as foam rubber (latex foam), shower caps, waterproof

textiles, rubber backed articles and clothes or pillows tted with

foam rubber pads should not be dried in the appliance.

•Fabric softeners, or similar products, should be used as specied

by the fabric softener instructions.

•Remove all objects from pockets such as lighters and matches.

•The appliance is not to be used if industrial chemicals have been

used for cleaning.

9

EN

Maintenance

•Securely plug the power plug in the socket outlet after completely

removing any moisture and dust.

•Disconnect the appliance from the power supply before cleaning

the appliance. Setting the controls to the OFF or stand by position

does not disconnect this appliance from the power supply.

•Do not spray water inside or outside the appliance to clean it.

•Never unplug the appliance by pulling on the power cable. Always

grip the power plug rmly and pull straight out from the socket

outlet.

Disposal

•Before discarding an old appliance, unplug it. Cut off the cable

directly behind the appliance to prevent misuse.

•Dispose of all packaging materials (such as plastic bags and

styrofoam) away from children. The packaging materials can cause

suffocation.

•Remove the door before disposing of or discarding this appliance to

avoid the danger of children or small animals getting trapped inside.

10

INSTALLATION

EN

Parts

12

1

Transit bolts

2

Power plug

3

Drawer

4

Control panel

5

Drum

6

Door

7

Drain hose

8

Drain plug

9

Drain pump lter

10

Cover cap (Location may

vary depending on products)

11

Adjustable feet

12

Power button

Accessories

Cold supply hose (1 EA)

(Option: Hot (1 EA))

Spanner Caps for covering

transit bolt holes

(Optional)

Anti–slip sheets (2 EA)

(Optional)

Elbow bracket for

securing drain hose

(Optional)

Tie strap (Optional)

Stacking holder,

Screws (3 EA)

(Optional)*

• * : Save these accessories for future use. These accessories will be used for stacking with Pedestal

washing machine. Refer to the owner’s manual for Pedestal washing machine for Installation.

11

EN

Model

G-CS1612W

Wash Capacity 12 kg (Wash) / 8 kg (Dry)

Power Supply 220-240 V~, 50 Hz

Size 600 mm (W) x 610 mm (D) x 850 mm (H)

Product Weight 76 kg

Permissible Water pressure 0.1 - 1.0 MPa (1.0 - 10.0 kgf / cm²)

•

• .

12

EN

Installation Place

Requirements

Location

2 cm

0.5 cm

2 cm10 cm

Level oor : Allowable slope under the entire

appliance is 1°.

Power outlet : Must be within 1 meter of either

side of the location of the appliance.

• Do not overload the outlet with more than one

appliance.

Additional Clearance : For the wall, 10 cm:

rear/2 cm: right & left side

• Do not place or store laundry products on top

of the appliance at any time. These products

may damage the nish or controls.

WARNING

• The plug must be plugged into an appropriate

outlet that is properly installed and grounded

in accordance with all local codes and

ordinances.

Positioning

• Install the appliance on a at hard oor.

• Make sure that air circulation around the

appliance is not impeded by carpets, rugs, etc.

• Never try to correct any unevenness in the

oor with pieces of wood, cardboard or similar

materials under the appliance.

• If it is impossible to avoid positioning the

appliance next to a gas cooker or coal burning

stove, an insulation (85x60 cm) covered with

aluminum foil on the side facing the cooker

or stove must be inserted between the two

appliances.

• Do not install the appliance in rooms where

freezing temperatures may occur. Frozen

hoses may burst under pressure. The reliability

of the electronic control unit may be impaired

at temperatures below freezing point.

• Ensure that when the appliance is installed, it

is easily accessible for an engineer in the event

of a breakdown.

• With the appliance installed, adjust all four

feet using the transit bolt spanner provided to

ensure the appliance is stable, and a clearance

of approximately 5 mm is left between the

top of the appliance and the underside of any

worktop

• If the appliance is delivered in winter and

temperatures are below freezing, place the

appliance at room temperature for a few hours

before putting it into operation.

WARNING

• This equipment is not designed for maritime

use or for use in mobile installations such as

caravans, aircraft etc.

Electrical Connection

• Do not use an extension cord or double

adapter.

• Always unplug the appliance and turn off the

water supply after use.

• Connect the appliance to an earthed socket in

accordance with current wiring regulations.

• The appliance must be positioned so that the

plug is easily accessible.

• Repairs to the appliance must only be carried

out by qualied personnel. Repairs carried out

by inexperienced persons may cause injury

or serious malfunctioning. Contact your local

service centre.

13

EN

Unpacking and Removing

Transit Bolts

1

Lift the appliance off the foam base.

• After removing the carton and shipping

material, lift the appliance off the foam

base. Make sure the tub support comes off

with the base and is not stuck to the bottom

of the appliance.

• If you must lay the appliance down to

remove the carton base, always protect the

side of the appliance and lay it carefully on

its side. Do not lay the appliance on its front

or back.

Tub Support

(Optional)

Carton

base

2

Remove the bolt assemblies.

• Starting with the bottom two transit

bolts, use the spanner (included) to fully

loosen all transit bolts by turning them

counterclockwise. Remove the bolt

assemblies by wiggling them slightly while

pulling them out.

3

Install the hole caps.

• Locate the hole caps included in the

accessory pack or attached on the back.

Cap

NOTE

• Save the bolt assemblies for future use. To

prevent damage to internal components, Do

not transport the washing machine without

reinstalling the transit bolts.

• Failure to remove transit bolts and retainers

may cause severe vibration and noise, which

can lead to permanent damage to the washing

machine. The cord is secured to the back of

the washing machine with a transit bolt to help

prevent operation with transit bolts in place.

14

EN

Using Anti-Slip Sheets

(Optional)

If you install the appliance on a slippery surface,

it may move because of excessive vibration.

Incorrect leveling may cause malfunction

through noise and vibration. If this occurs, install

the anti-slip sheets under the leveling feet and

adjust the level.

1

Clean the oor to attach the anti-slip sheets.

• Use a dry rag to remove and clean foreign

objects and moisture. If moisture remains,

the anti-slip sheets may slip.

2

Adjust the level after placing the appliance in

the installation area.

3

Place the adhesive side of the anti-slip

sheets on the oor.

• It is most effective to install the anti-slip

sheets under the front legs. If it is difcult to

place the pads under the front legs, place

them under the back legs.

This side up

Adhesive side

4

Ensure the appliance is level.

• Push or rock the top edges of the appliance

gently to make sure that the appliance does

not rock. If the appliance rocks, level the

appliance again.

NOTE

• You can obtain anti-slip sheets from the LG

Service Centre.

Wooden Floors (Suspended

Floors)

• Wooden oors are particularly susceptible to

vibration.

• To prevent vibration we recommend you place

rubber cups at least 15 mm thick of the each

foot of the appliance, secured to at least two

oor beams with screws.

Rubber Cup

• If possible install the appliance in one of the

corners of the room, where the oor is more

stable.

• Fit the rubber cups to reduce vibration.

NOTE

• Proper placement and leveling of the washing

machine will ensure long, regular, and reliable

operation.

• The washing machine must be 100%

horizontal and stand rmly in position.

• It must not ‘Seesaw’ across corners under the

load.

• The installation surface must be clean, free

from oor wax and other lubricant coatings.

• Do not let the feet of the washing machine get

wet. Failure to do so may cause vibration or

noise.

• You can obtain rubber cups

(p/no.4620ER4002B) from the LG Service

Centre.

15

EN

Leveling the Appliance

If the oor is uneven, turn the adjustable feet as

required (Do not insert pieces of wood etc. under

the feet). Make sure that all four feet are stable

and resting on the oor and then check that the

appliance is perfectly level (Use a spirit level).

• Once the appliance is level, tighten the lock

nuts up towards the base of the appliance. All

lock nuts must be tightened.

Raise Lower

Lock nut

Tighten all 4

lock nuts securely

Diagonal Check

• When pushing down the edges of the top plate

diagonally, the appliance should not move up

and down at all (check both directions). If the

appliance rocks when pushing the machine top

plate diagonally, adjust the feet again.

NOTE

• Timber or suspended type ooring may

contribute to excessive vibration and

unbalance.

• If the washing machine is installed on a raised

platform, it must be securely fastened in order

to eliminate the risk of falling off.

Connecting the Water Supply

Hose

• Water pressure must be between 0.1 MPa and

1.0 MPa (1.0‒10.0 kgf/cm

2

).

• Do not strip or crossthread when connecting

supply hose to the valve.

• If the water pressure is more than 1.0 MPa, a

decompression device should be installed.

• Periodically check the condition of the hose

and replace the hose if necessary.

Checking the Rubber Seal on the

Water Supply Hose

Two rubber seals are supplied with the water

inlet hoses. They are used for preventing water

leaks. Make sure the connection to taps is

sufciently tight.

Hose connector

Rubber seal

Hose connector

Rubber seal

16

EN

Connecting Hose to Water Tap

Connecting Screw-Type Hose to Tap

with Thread

Screw the hose connector onto the water supply

tap.

Connecting Screw-Type Hose to Tap

Without Thread

1

Loose the four xing screws.

Upper

connector

Rubber

seal

Fixing screw

2

Remove the guide plate if the tap is too large

to t the adapter.

Guide plate

3

Push the adapter onto the end of the tap

so that the rubber seal forms a watertight

connection. Tighten the four xing screws.

4

Push the supply hose vertically upwards

so that the rubber seal within the hose can

adhere completely to the tap and then tighten

it by screwing it to the right.

Plate

Supply

hose

Connecting One Touch Type Hose to

Tap Without Thread

1

Unscrew the adapter ring plate and loose the

four xing screws.

Ring plate

2

Remove the guide plate if the tap is too large

to t the adapter.

Guide plate

17

EN

3

Push the adapter onto the end of the tap

so that the rubber seal forms a watertight

connection. Tighten the four xing screws

and the adapter ring plate.

4

Pull the connector latch plate down, push the

supply hose onto the adapter, and release

the connector latch plate. Make sure the

adapter locks into place.

Latch plate

NOTE

• Before connecting the supply hose to the water

tap, turn on the water tap to ush out foreign

substances (dirt, sand, sawdust, and etc.)

in the water lines. Let the water drain into a

bucket, and check the water temperature.

Connecting Hose to Appliance

Attach the hot water line to the hot water supply

on the back of the washer. Attach the cold water

line to the cold water supply on the back of the

washer.

Cold water

supply

Hot water

supply

NOTE

• After completing connection, if water leaks

from the hose, repeat the same steps. Use

the most conventional type of tap for the water

supply. In case the tap is square or too big,

remove the guide plate before inserting the tap

into the adaptor.

Using the Horizontal Tap

Horizontal tap

Extension tap

Square tap

18

EN

Installing the Drain Hose

• The drain hose should not be placed higher

than 100 cm above the oor. Water in the

appliance may not drain or may drain slowly.

• Securing the drain hose correctly will protect

the oor from damage due to water leakage.

• If the drain hose is too long, do not force

it back into the appliance. This will cause

abnormal noise.

max. 100 cm

~ 100 cm

~ 145 cm

~ 105 cm

• When installing the drain hose to a sink, secure

it tightly with string.

• Securing the drain hose correctly will protect

the oor from damage due to water leakage.

max. 100 cm

Laundry tub

Hose retainer

Tie strap

19

OPERATION

EN

Using the Washing Machine

Before the rst wash, select a washing

programme, allow the washing machine to wash

without clothing. This will remove residue and

water from the drum that may have been left

during manufacturing.

1

Sort laundry and load items.

• Sort laundry by fabric type, soil level, colour

and load size as needed. Open the door

and load items into the washing machine.

2

Add cleaning products and/or detergent and

softener.

• Add the proper amount of detergent to the

detergent dispenser drawer. If desired, add

bleach or fabric softener to the appropriate

areas of the dispenser.

3

Turn on the washing machine.

• Press the Power button to turn on the

washing machine.

4

Choose the desired washing cycle.

• Press the cycle button repeatedly or turn

the cycle selector knob until the desired

cycle is selected.

5

Begin cycle.

• Press the Start/Pause button to begin the

cycle. The washing machine will agitate

briey without water to measure the weight

of the load. If the Start/Pause button is

not pressed within 5 minutes, the washing

machine will shut off and all settings will be

lost.

6

End of cycle.

• When the cycle is nished, a melody will

sound. Immediately remove your clothing

from the washing machine to reduce

wrinkling. Check around the door seal when

removing the load for small items that may

be caught in the seal.

NOTE

• The button cannot be recognized when the

door is open. Press again after closing the

door.

20

EN

Sorting Laundry

1

Look for a care label on your clothes.

• This will tell you about the fabric content of

your garment and how it should be washed.

• Symbols on the care labels.

Wash temperature

Normal machine wash

Permanent press

Delicate

Hand wash

Do not wash

2

Sorting laundry.

• To get the best results, sort clothes into

loads that can be washed with the same

wash cycle.

• Different fabrics need to be washed at

varying temperatures and spin speeds.

• Always sort dark colours from pale colours

and whites. Wash separately as dye and lint

transfer can occur causing discolouration of

white and pale garments. If possible, do not

wash heavily soiled items with lightly soiled

ones.

− Soil (Heavy, Normal, Light) :

Separate clothes according to amount of

soil.

− Colour (White, Lights, Darks):

Separate white fabrics from coloured

fabrics.

− Lint (Lint producers, Collectors):

Wash lint producers and lint collectors

separately.

3

Caring before loading.

• Combine large and small items in a load.

Load large items rst.

• Large items should not be more than half

the total wash load. Do not wash single

items. This may cause an unbalanced load.

Add one or two similar items.

• Check all pockets to make sure that they

are empty. Items such as nails, hair clips,

matches, pens, coins and keys can damage

both your washing machine and your

clothes.

• Close zippers, hooks and strings to make

sure that these items don’t snag on other

clothes.

• Pre-treat dirt and stains by brushing a small

amount of detergent dissolved water onto

stains to help lift dirt.

CAUTION

• Check inside the drum and remove any items

from a previous wash.

ページが読み込まれています...

LG G-CS1612W ユーザーガイド

LG G-CS1612W ユーザーガイド

他の言語で

関連論文

その他のドキュメント