User Manual Ver 1.0.4
Model No.: TE-25A
Features
Page 1
Mechanical Structures and Installations
Triac Constant Current LED Driver
● Dimming interface: Triac/ELV, AC Push-Dim
● Apply to leading edge/trailing edge Triac dimmers and dimming system
● PWM digital dimming, no alter LED color rending index
● 1 channel constant current output, configurable current via DIP switch
● Over-heat / Over-load / Short circuit protection, recover automatically
● Full protective plastic case
● Suitable for indoor LED lighting application
● 5 Year, 50,000hr warranty
Output Voltage
Output Current
Output Power
Dimming Range
PWM Frequency
Input Voltage Range
Frequency Range
Efficiency
Alternating Current
Inrush Current
Leakage Current
No Load Power
Over Load Power
Short Circuit
Over Temperature
Woking Temperature
T-case Max
Working Humidity
Storage Temp/Humidity
Temperature Coefficient
Vibration Resistance
Security Specifications
Withstand Voltage
Insulation Resistance
EMC Emission
EMC Immunity
When O/P voltage exceed its range, O/P current declines, auto recovers when the load is reduced.
Shutdownautomaticallyifshortcircuitoccurs, auto recovers.
Protection
Environment
Safety&EMC
-30℃～55℃
70℃
0～100％
2000Hz
200～240VAC
50/60Hz
Output
Input
Intelligently adjust or turn off the output current if the PCB temp > 100℃,auto recovers.
20％～90％RH, non-condensing
-40℃～80℃,10％～95％RH
±0.03％/℃ (0-50％)
10-500Hz, 2G, 6min/cycle, X,Y,Z axes/2min
IEC/EN61347-1, IEC/EN61347-2-13
I/P-O/P: 3750VAC
I/P-O/P: 100MΩ/500VDC/25℃/70％RH
EN61000-4-2.3.4.5.6.8.11, EN61547
EN55015, EN61000-3-2 Class C, IEC61000-3-3
LED output -
AC N input
AC L input Installation rack
LED output +
Technical Parameters
TE-25A Triac Constant Current LED Driver
AC Push input
IP Rating
Certications
IP20
CE, EMC
Applications
● Suitable for downlight, spotlight and decorative applications.
● Office / Commercial / Domestic Lighting, Hotels, Classrooms, Warehouse, Health care, Retail and Display.
● Use for retrofit upgrades & new luminaire designs.
Current Accuracy
Max Output Voltage
10-52VDC
250-900mA
Max. 25W
Cold start 27.5A at 230VAC
±3％
58VDC
0.22A/220VAC
>80%/220VAC
< 1.9W
< 0.5mA/230VAC
LED Current Selection:
DIP Switch for current selection
LED OUTPUT
LED
LED
L
L1
N
Push DIM
LL1
INPUT
200-240VAC
1 2 3
Warranty
5 years
Short Circuit
Protection
Over Load
Protection
Over-heat
Protection
Synchronization
Digital
Dimming
Push-Dim
Multiple Current
ON
1 2 3
Tri ac
Dimming
123
Output Voltage
Output Current
Output Power
10-52V 10-52V 10-52V 10-52V 10-50V 10-42V 10-36V 10-28V
250mA 300mA 350mA 400mA 500mA 600mA 700mA 900mA
2.5-13W 3-15.6W 3.5-18.2W 4-20.8W 5-25W 6-25.2W 7-25.2W 9-25.2W
44 mm
168.5 mm
30 mm
Wiring Diagram
User Manual Ver 1.0.4
AC 100-240V
3. Connect AC Pushswitch
Page 2
PushSwitch
L
N
2. Connect Triac dimmer(with Neutral wire)
1. Connect Triac dimmer(no Neutral wire)
L
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
1 2 3
N
L
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
12 3
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
1 2 3
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
1 2 3
N
Dimming Curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.6
● Short press:
Turn on or off light.
● Long press (1-6s):
Press and hold to step-less dimming,
With every other long press, the light level goes to the opposite direction.
● Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure.
● Synchronization:
If more than one LED driver are connected to the same push switch, do a long press for more than 10s,
then the system is synchronized and all lights in the group dim up to 100%.
This means there is no need for any additional synchrony wire in larger installations.
We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces,
The maximum length of the wires from push to LED driver should be no more than 20 meters.
The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching
(momentary) wall switchs.
While connected with a Triac dimmer, such as Lutrom, Clipsal, Dynalite dimmer, different Triac dimmers from different
suppliers may have different minimum dimming levels which the driver can not be dimmed below. To dim to 1%,
please make sure the dimmer supports 1% minimum dimming level.
Triac Dimming Input
AC Push-Dim input
TE-25A Triac Constant Current LED Driver
123
44 mm
168.5 mm
30 mm
10-52V 10-52V 10-52V 10-52V 10-50V 10-42V 10-36V 10-28V
250mA 300mA 350mA 400mA 500mA 600mA 700mA 900mA
2.5-13W 3-15.6W 3.5-18.2W 4-20.8W 5-25W 6-25.2W 7-25.2W 9-25.2W
LED OUTPUT
LED
LED
L
L1
N
Push DIM
LL1
INPUT
200-240VAC
1 2 3
当输出电压超出范围时关闭输出，可⾃动恢复
输出短路时关闭输出，可⾃动恢复
-30℃～50℃
70℃
当PCB温度⼤于100℃时降低输出电流或关闭输出，可⾃动恢复
20％～90％RH, ⽆冷凝
-40℃～80℃10％～95％RH,
±0.03％/℃ (0-50％)
10-500Hz,2G, 6分钟/ X轴/ 分钟周期, ,Y,Z2
IEC/EN61347-1, IEC/EN61347-2-13
I/P-O/P: 3750VAC
I/P-O/P: 100MΩ/500VDC/25℃/70％RH
EN61000-4-2.3.4.5.6.8.11, EN61547
EN55015, EN61000-3-2 Class C, IEC61000-3-3
IP20
CE, EMC
版本1.0.3
特点
第1页
机械结构和安装
应⽤
●适⽤于筒灯，聚光灯和装饰应⽤。
●办公室/商业/家庭照明，酒店，教室，仓库，医疗保健，零售和展⽰。
●⽤于改造升级和新灯具设计。
技术参数
输出电流精度
安全&EMC
安全规范
耐压
绝缘电阻
EMC电磁兼容发射
认证
⼯作温度
⼯作湿度
储存温度/湿度
温度系数
抗振性
环境
防⽔等级
过载保护
短路保护
过温保护
保护
输出电压
输出电流
输出功率
最⼤输出电压
调光范围
PWM频率
输⼊电压范围
频率范围
效率
输出
输⼊ 输⼊电流
待机功率
浪涌电流
漏电流
外壳最⼤温度
EMC电磁兼容抗扰度
型号:TE-25A
可控硅调光恒流LED电源
Push-Dim
ON
1 2 3
多档电流 0/1-10V调光 数字调光
对数调光 同步 过热保护 过载 保护
短路保护 5年质保
●调光接⼝：Triac/ELV，AC⾃复位开关
●适⽤于前切/后切Triac调光器和调光系统
●PWM数字调光，不改变LED显⾊指数
●1通道恒流输出，可通过DIP开关配置电流
●连接⾃复位开关，实现开/关和0-100％调光
●过热/过载/短路保护，⾃动恢复
●全保护塑料外壳
●适⽤于室内LED照明应⽤
●5年，50,000⼩时保修
安装⼝
LED 输出 -
LED 输出 +
DIP拨码开关⽤于选择输出电流
AC N 输⼊
AC L 输⼊
⾃复位开关输⼊
输出电压
输出电流
输出功率
LED输出电流选择：
0～100％
2000Hz
200VAC～240VAC
50/60Hz
10-52VDC
250-900mA
Max. 25W
冷启动27.5A/230VAC
±3％
58VDC
0.22A/220VAC
>80%/220VAC
< 1.9W
< 0.5mA/230VAC
AC 100-240V
3.连接AC⾃复位开关
⾃复位开关
L
N
L
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
1 2 3
N
L
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
12 3
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
1 2 3
N
LED OUTPUT
LED
LED
L
L1
Push DIM
LL1
INPUT
200-240VAC
1 2 3
N
AC⾃复位开关调光输⼊
2.连接可控硅调光器(有零线)
1.连接可控硅调光器(⽆零线)
接线图
版本1.0.3 第2页
可控硅调光输⼊
当连接到其他品牌的可控硅调光器，如Lutrom,Clipsal,Dynalite等的调光器，
不同品牌的调光器有不同的最低调光值，我们的调光电源不能调到低于调光器的亮度值。
如需调暗到1%，请确保调光器⽀持1%的最低调光值。
●短按：
开启或关闭灯光。
●⻓按（1-6s）：
⽆级调光，亮度连续增加或降低，
每次松开后再次⻓按，亮度反⽅向变化。
●调光记忆：
⻓按设置的亮度值，有掉电记忆。
●同步：
如果多个调光电源连接到同⼀个⾃复位开关，请先⻓按10秒，将所有灯光同步调⾄100％亮度。
建议连接到同⼀个⾃复位开关的调光电源数量不超过25个，⾃复位开关的连接线⻓不超过20⽶。
⾃复位开关接⼝可连接⾃复位⾯板开关或⾃复位按键来调光。
调光曲线
100
90
80
70
60
50
40
30
20
10
PWM占 空 比(%)
50 60 70 80 90 100
亮度(%)
10 20 30 40
Gamma=1.6
-
1
-
2
-
3
-
4
