Samsung WD8122CVB/XSP ユーザーマニュアル

Washing Machine

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/global/register

WD8122CVD

WD8122CVB

WD8122CVW

WD8122CVC

WD8122CVB-02574C_EN.indd 1 2008-06-05 ¿ÀÈÄ 2:09:31

2_ features

features of your new samsung

washing machine

Your new washing machine will change the way you feel about doing laundry. From

its super-size capacity to its energy efﬁciency, the Samsung washing machine has

all the features to turn a mundane chore into a pleasure.

• Diamond Drum - A More Powerful Wash

Performance while Protecting your

Fabric

Provides a much better wash performance than normal

drum washers, by using the wash board effect created by

the waves of the inside drum.

• Ball Balance - Enjoy the Silence! No Noise, No Vibrations

Reduced vibrations and noise through the use of a Ball Balance system which maintains near

perfect drum balance.

• Customizable Economic Function - Water, Time and Power

Saving

Detects the laundry weight in 7 steps and reduces water, time and power consumption.

• Air Wash - Sterilization and Deodorization without Water!

Refresh your favorite clothing simply by using air after you’ve been at a party or have gone out

(food, cigarettes). Non-stained clothing no longer needs to be washed, simply refresh them

using the 4 available cycles for different fabrics.

• Silver Wash - Sterilization and Anti-bacteria Effect with Cold

Water Only

The winning combination! Samsung’s silver technology combines the sanitizing effect of silver

with state-of-the-art science for the ultimate in clean. Two plates of pure silver are converted

into silver ions through electrolysis. Even in cold, bleach-less water, the silver particles remove

odor-causing bacteria for a “super clean” wash. So washing in cold water is energy efﬁcient

and better for your clothes.

• Direct Drive Motor

As the drum does not utilize belts or gears, vibrations are reduced signiﬁcantly. This feature

ensures that your washer machine is quieter and more durable.

• Child Lock

The Child Lock function ensures that curious little hands are kept out of your washing

machine.

This safety feature stops your children from playing with the washing machine, and alerts you

when it is activated.

WD8122CVB-02574C_EN.indd 2 2008-06-05 ¿ÀÈÄ 2:09:32

features _3

• Delay End

Delay a cycle for up to 19 hours in one-hour increments and increase the convenience of

using your washing machine especially when you have to go out.

• Wool Certiﬁed

The machine has been tested and has passed the required Woolmark Company

speciﬁcations for machine washable wool products.

Fabrics should be washed according to the instructions on the garment label as speciﬁed by

Woolmark and Samsung.

• Digital Graphic Display

The Digital Graphic Display (control panel) is clear and easy to use for minimum fuss and

hassle. And while it is easy to use, the Digital Graphic Display enables you to make quick and

accurate adjustments to your wash for excellent washing results.

• Wide door

Extra wide door aperture for convenient viewing! Easily add and remove laundry, especially for

large sized laundry items such as bedding, towels etc.

This manual contains important information on the installation, use, and care of your new

Samsung washing machine. Refer to it for descriptions of the control panel, instructions on how

to use the washing machine, and tips for making the most of its state-of-the-art features and

functions. The Troubleshooting section on page 29 tells you what to do if something goes wrong

with your new washing machine.

WD8122CVB-02574C_EN.indd 3 2008-06-05 ¿ÀÈÄ 2:09:32

4_ safety information

safety information

Throughout this manual, you’ll see Warning and Caution notes. These

warnings, cautions, and the important safety instructions that follow do not cover

all possible conditions and situations that may occur. It’s your responsibility to use

common sense, caution, and care when installing, maintaining, and operating your

washing machine. Samsung is not liable for damages resulting from improper use.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage

.

CAUTION

To reduce the risk of ﬁre, explosion, electric shock, or personal

injury when using your washing machine, follow these basic safety

precautions:

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

As with any equipment using electricity and moving parts, potential hazards exist. To safely

operate this appliance, become familiar with its operation and exercise care when using it.

Install and store your washing machine inside, away from exposure to weather.

Install and level your washing machine on a ﬂoor that can support its weight.

Your washing machine must be properly grounded. Never plug it into an ungrounded outlet.

WD8122CVB-02574C_EN.indd 4 2008-06-05 ¿ÀÈÄ 2:09:34

safety information _5

To reduce the risk of ﬁre or explosion:

• Do not wash items that have been washed, soaked, or treated with gasoline, dry

cleaning solvents, or other ﬂammable or explosive substances. They give off vapors that

could ignite or explode. Rinse by hand any material that has been exposed to cleaning

solvent or other ﬂammable liquids or solids before putting in your washing machine. Be

sure that all traces of such liquids, solids, and fumes have been removed. Dangerous

substances include acetone, denatured alcohol, gasoline, kerosene, certain liquid

household cleaners and spot removers, turpentine, waxes, and wax removers.

• Do not put gasoline, dry cleaning solvents, or other ﬂammable or explosive substances

into the washing machine.

• Under certain conditions, hydrogen gas may be produced in a hot water system–such

as your hot water heater -- that has not been used for two weeks or more. HYDROGEN

GAS IS EXPLOSIVE. If your hot water system has not been used for two weeks or

more, turn on all hot water taps in your home, and let the water ﬂow for several minutes

before using your washing machine. This will release any hydrogen gas build–up. Since

hydrogen gas is ﬂammable, do not smoke or light an open ﬂame during this time.

Ventilate immediately without touching the power plug if there is a gas leak.

Unplug the power cord before servicing your washing machine.

Before each wash, empty the pockets of your laundry. Small, irregularly shaped hard

objects, such as coins, knives, pins, and paperclips could damage your washing machine.

Do not wash clothing with large buckles, buttons, or other heavy metal metal.

Do not open the door of the washing machine if you can still see water. Check that the

water has drained before opening the door.

Do not repair, replace, or service any part of your washing machine yourself unless you fully

understand the recommended user–repair instructions and have the skills to carry them

out. Work done by an unauthorized person may void your warranty.

Connect the washing machine to the water mains using the new set of hoses. Do not reuse

the old set of hoses.

Water inlet hoses deteriorate over time. Check the hoses periodically for bulges, kinks, cuts,

wear, and leaks, and replace them as needed and at least every ﬁve years.

Packing materials can be dangerous to children; keep all packing material (plastic bags,

polystyrene, etc.) well out of the reach of children.

All packaging and shipping bolts must be removed before the appliance is used. Serious

damage may occur if they are not removed. See “Removing the shipping bolts”.

Before washing clothes for the ﬁrst time, you must run a complete cycle without clothes.

See “Washing for the ﬁrst time”.

CAUTION

WD8122CVB-02574C_EN.indd 5 2008-06-05 ¿ÀÈÄ 2:09:34

6_ safety information

The appliance is designed for home use only.

Make sure that water and electrical connections are made by qualiﬁed technicians,

observing the manufacturer’s instructions (see “Installing the Washing Machine”) and local

safety regulations.

Before cleaning or carrying out maintenance, unplug the appliance from the electrical outlet.

Always unplug the appliance and turn off the water after use.

Make sure that the pockets of all clothing to be washed are empty.

Hard, sharp objects, such as coins, safety pins, nails, screws, or stones can cause

extensive damage to the appliance.

Never allow pets and children to play on or in the appliance. It may cause injury or suffocate

them.

The glass door becomes very hot during the washing cycle. Never touch on the glass door

while it is in use.

Do not attempt to repair the appliance yourself. Repairs made by inexperienced or

unqualiﬁed persons may cause injury and/or make more serious repairs to the appliance

necessary.

If the plug (power supply cord) is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualiﬁed person in order to avoid a hazard.

This appliance should only be serviced by our authorized service center, and only rated

spare parts should be used.

Do not let children (or pets) play on or in your washing machine. The washing machine door

does not open easily from the inside, and children may be seriously injured if trapped inside.

This appliance is not intended for use by young children or inﬁrm persons unless they

have been adequately supervised by a responsible person to ensure that they can use the

appliance safely.

Young children should be supervised to ensure that they do not play with the appliance.

To use this appliance safely, the user should become familiar with the instructions for

operation of the appliance and always take extra care when using it.

This appliance should be positioned to be accessible to the power plug, the water supply

tabs and the drain pipes.

Do not use processed water containing oil, cream or lotion, which is usually found in

skincare shops or massage clinics.

• Otherwise this will cause the packing to be deformed, which causes a malfunction or

water leak.

safety information

WARNING

WD8122CVB-02574C_EN.indd 6 2008-06-05 ¿ÀÈÄ 2:09:34

safety information _7

A stainless washing tub does not usually rust. However if some metal such as a hair pin is

left in the tub for an extended time, the tub could rust.

• Do not leave water or bleach containing chlorine in the tub for an extended period of

time.

• Do not regularly use or leave water containing iron in the tub for an extended period of

time. If rust starts appearing on the surface of the tub, apply a cleansing agent (neutral)

to the surface and use a sponge or soft cloth to clean it. (Under no circumstances use a

metal brush)

For washing machines with ventilation openings in the base, ensure that the opening is not

obstructed by carpet or any other obstacles.

Use the new hose-sets and old hose-sets should not be reused.

WD8122CVB-02574C_EN.indd 7 2008-06-05 ¿ÀÈÄ 2:09:34

8_ contents

contents

SETTING UP YOUR WASHING

MACHINE

9

9 Checking the parts and the control panel

10 Meeting installation requirements

10 Electrical supply and grounding

10 Water Supply

11 Drain

11 Flooring

11 Surrounding temperature

11 Alcove or closet installation

11 Installing your washing machine

WASHING A LOAD OF LAUNDRY

17

17 Washing for the ﬁrst time

17 Basic instructions

18 Using the control panel

20 Child lock

20 Delay end

20 Stop&Add

21 Air wash

22 Washing clothes using cycle selector

23 Washing clothes manually

25 Detergent and additives information

25 Which detergent to use

25 Detergent drawer

CLEANING AND MAINTAINING YOUR

WASHING MACHINE

26

26 Draining the washing machine in an

emergency

26 Cleaning the exterior

27 Cleaning the detergent drawer and drawer

reces

s

27 Cleaning the debris ﬁlter

28 Cleaning the water hose mesh ﬁlter

28 Repairing a frozen washing machine

28 Storing your washing machine

TROUBLESHOOTING AND

INFORMATION CODES

29

29 Check these points if your washing machine...

30 Information codes

CYCLE CHART

31

31 Cycle chart

APPENDIX

32

32 Fabric care chart

32 Protecting the environment

32 Declaration of conformity

33 Speciﬁcations

WD8122CVB-02574C_EN.indd 8 2008-06-05 ¿ÀÈÄ 2:09:34

setting up your new washing machine _9

01 SETTING UP

setting up your washing

machine

Be sure to have your installer follow these instructions closely so that your new

washing machine works properly and so that you’re not at risk of injury when doing

laundry.

CHECKING THE PARTS AND THE CONTROL PANEL

Carefully unpack your washing machine, and make sure you’ve received all of the parts shown below.

If your washing machine was damaged during shipping, or if you do not have all of the parts, contact

Samsung Customer Service or your Samsung dealer.

Spanner

Bolt hole

covers

Water supply

hose

Hose guide Drain hose User manual

(use for the

lower bolt hole)

Detergent drawer

Control panel

Door

Adjustable feet

Plug

Drain hose

Debris ﬁlter

Filter Cover

Emergency drain tube

Option

WD8122CVB-02574C_EN.indd 9 2008-06-05 ¿ÀÈÄ 2:09:36

10_ setting up your new washing machine

setting up your washing

machine

MEETING INSTALLATION REQUIREMENTS

Electrical supply and grounding

To prevent unnecessary risk of ﬁre, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest

Revision and local codes and ordinances. It is the personal responsibility of the appliance owner

to provide adequate electrical service for this appliance.

Never use an extension cord.

Use only the power cord that comes with your washing machine.

When preparing for installation, ensure that your power supply offers:

• 220V~240V 50Hz 15 AMP fuse or circuit breaker

• Individual branch circuit serving only your washing machine

Your washing machine must be grounded. If your washing machine malfunctions or breaks

down, grounding will reduce the risk of electric shock by providing a path of least resistance for

the electric current.

Your washing machine comes with a power cord having a three-prong grounding plug for use in

a properly installed and grounded outlet.

Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Improperly connecting the equipment-grounding conductor can result electrical shock.

Check with a qualiﬁed electrician or serviceman if you are unsure if the washing machine is

properly grounded. Do not modify the plug provided with the washing machine. If it does not ﬁt

the outlet, have a proper outlet installed by a qualiﬁed electrician.

Water Supply

Your washing machine will ﬁll properly when your water pressure is 50 kPa ~ 800 kPa. Water

pressure less than 50 kPa may cause water valve failure, not allowing the water valve to shut

off completely. Or, it may take the washing machine longer to ﬁll than what the controls allow,

resulting in your washing machine turning off. (A ﬁll-time limit, designed to prevent overﬂows/

ﬂooding if an internal hose becomes loose, is built into the controls.)

The water taps must be within 4 feet (122cm) of the back of your washing machine for the

provided inlet hoses provided to reach your washing machine.

Most plumbing supply stores sell inlet hoses of various lengths up to 10 feet (305 cm) long.

You can reduce the risk of leaks and water damage by:

• Making water taps easily accessible.

• Turning off taps when the washing machine is not in use.

• Periodically checking for leaks at water inlet hose ﬁttings.

Before using your washing machine for the ﬁrst time, check all connections at the water

valve and taps for leaks.

WARNING

WD8122CVB-02574C_EN.indd 10 2008-06-05 ¿ÀÈÄ 2:09:36

setting up your new washing machine _11

01 SETTING UP

Drain

Samsung recommends a standpipe height of 18 in (46 cm). The drain hose must be routed

through the drain hose clip to the standpipe. The standpipe must be large enough to accept the

outside diameter of the drain hose. The drain hose is attached at the factory.

Flooring

For best performance, your washing machine must be installed on a solidly constructed ﬂoor.

Wood ﬂoors may need to be reinforced to minimize vibration and/or unbalanced loads. Carpeting

and soft tile surfaces are contributing factors to vibrations and the tendency for your washing

machine to move slightly during the spin cycle.

Never install your washing machine on a platform or poorly supported structure.

Surrounding temperature

Do not install your washing machine in areas where water may freeze, since your washing

machine always retains some water in its water valve, pump, and hose areas. Frozen water in

the lines can cause damage to belts, the pump, and other components. You should always use

your washing machine when the surrounding temperature is at least 60 ˚F (16 ˚C).

Alcove or closet installation

To operate safely and properly, your new washing machine requires minimum clearances of:

Sides – 25 mm (1 in) Rear – 51 mm (2 in)

Top – 25 mm (1 in) Front – 465 sq.cm (72 sq.in.)

If both the washing machine and a dryer are installed together, the front of the alcove or closet

must have at least 72 sq. in. (465 sq. cm) unobstructed air opening. Your washing machine

alone does not require a speciﬁc air opening.

INSTALLING YOUR WASHING MACHINE

STEP 1

Selecting a location

Before you install the washing machine, make sure the location:

• Has a hard, level surface without carpeting or ﬂooring that may obstruct ventilation

• Is away from direct sunlight

• Has adequate ventilation

• Will not be freezing (below 32 ˚F or 0 ˚C)

• Is away from heat sources such as oil or gas

• Has enough space so that the washing machine doesn’t stand on its power cord

WD8122CVB-02574C_EN.indd 11 2008-06-05 ¿ÀÈÄ 2:09:36

12_ setting up your new washing machine

STEP 2

Removing the shipping bolts

Before installing the washing machine, you must remove the ﬁve shipping bolts from the back of

the unit.

1. Loosen all the bolts with the supplied wrench.

2. Hold the bolt with the spanner and pull it through the wide

section of the hole. Repeat for each bolt.

3. Fill the holes with the supplied plastic covers.

4. Store the shipping bolts away safely in case you have to move the washing machine in the

future.

Packaging materials can be dangerous to children; keep all packaging material (plastic

bags, polystyrene, etc.) well out of the reach of children.

setting up your washing

machine

WARNING

Option

WD8122CVB-02574C_EN.indd 12 2008-06-05 ¿ÀÈÄ 2:09:37

setting up your new washing machine _13

01 SETTING UP

STEP 3

Adjusting the levelling feet

When installing your washing machine, ensure that the power plug, the water supply and

the drain are easily accessible.

1. Slide the washing machine into position.

2. Level your washer by turning the adjustable nut, as shown

in the ﬁgure.

3. When your washing machine is level, tighten the locking

nut using the (-) screwdriver.

STEP 4

Connecting the water and drain

Connecting the water supply hose

1. Take the L-shaped arm ﬁtting for the cold water

supply hose and connect it to the cold water

supply intake on the back of the machine.

Tighten by hand.

The water supply hose must be connected

to the washing machine at one end and to

the water tap at the other. Do not stretch the

water supply hose. If the hose is too short,

replace the hose with a longer, high pressure

hose.

2. Connect the other end of the cold water supply

hose to your sink’s cold water tap and tighten

it by hand. If necessary, you can reposition the

water supply hose at the washing machine end

by loosening the ﬁtting, rotating the hose, and

retightening the ﬁtting.

For selected models with an additional hot water intake:

1. Take the red L-shaped arm ﬁtting for the hot water supply hose and connect it to the hot

water supply intake on the back of the machine. Tighten by hand.

2. Connect the other end of the hot water supply hose to your sink’s hot water tap and tighten

it by hand.

3. Use a Y-piece if you only want to use cold water.

Locking nut

Adjustable nut

Option

WD8122CVB-02574C_EN.indd 13 2008-06-05 ¿ÀÈÄ 2:09:38

14_ setting up your new washing machine

Connecting the water supply hose (selected models)

1. Remove the adaptor from the water supply hose.

2. First, using a ‘+’ type screwdriver, loosen the four screws

on the adaptor. Next, take the adaptor and turn part (2)

following the arrow until there is a 5 mm gap.

3. Connect the adaptor to the water tap by tightening the

screws ﬁrmly. Turn part (2) following the arrow and connect

(1) and (2).

4. Connect the water supply hose to the adaptor.

When you release part (3), the hose automatically

connects to the adaptor making a ‘click’ sound.

After you have connected the water supply

hose to the adaptor, ensure that it is connected

correctly by pulling the water supply hose

downwards.

5. Connect the other end of the water supply hose to the inlet

water valve at the rear of the washing machine. Screw the

hose clockwise all the way in.

setting up your washing

machine

1

2

Adoptor

Water supply

hose

1

2

5 mm

3

Option

WD8122CVB-02574C_EN.indd 14 2008-06-05 ¿ÀÈÄ 2:09:39

setting up your new washing machine _15

01 SETTING UP

6. Turn on the water supply and ensure that no water leaks

from the water valve, tap or adaptor. If there is a water

leaks, repeat the previous steps.

Do not use your washing machine if there is a water leak.

This may cause electrical shock or injury.

• If the water tap has a screw type tap, connect the water

supply hose to the tap as shown.

Use the most conventional type of tap for the water supply. In case the tap is square or too

big, remove the spacing ring before inserting the tap into the adaptor.

✗

WARNING

WD8122CVB-02574C_EN.indd 15 2008-06-05 ¿ÀÈÄ 2:09:39

16_ setting up your new washing machine

Connecting the drain hose

The end of the drain hose can be positioned in three ways:

1. Over the edge of a wash basin: The drain hose must be placed at a height of between 60

and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure

the guide to the wall with a hook or to the tap with a piece of string to prevent the drain hose

from moving.

2. ln a sink drain pipe branch: The drain pipe branch must be above the sink siphon so that

the end of the hose is at least 60 cm above the ground.

3. ln a drain pipe: We recommend using a 65 cm high vertical pipe; it must be no shorter than

60 cm and no longer than 90 cm.

STEP 5

Powering your washing machine

Plug the power cord into a wall sockets, a 230 volt 50 Hz approved electrical outlet protected by

a 15-amp fuse or comparable circuit breaker. (For more information on electrical and grounding

requirements, see page 10.)

setting up your washing

machine

Drain hose

Hose guide

60 ~ 90 cm

WD8122CVB-02574C_EN.indd 16 2008-06-05 ¿ÀÈÄ 2:09:40

washing a load of laundry _17

02 WASHING A LOAD OF LAUNDRY

washing a load of laundry

With your new Samsung washing machine, the hardest part of doing laundry will be

deciding which load to wash ﬁrst.

WASHING FOR THE FIRST TIME

Before washing laundry for the ﬁrst time, you must run a complete empty cycle (i.e. no laundry).

1. Press the Power button.

2. Add a little detergent to the detergent compartment in

the detergent drawer.

3. Turn on the water supply to the washing machine.

4. Press the Start/Pause button.

This will remove any water that might be left over in the

machine from the manufacturer’s test run.

Compartment : Detergent for prewash, or starch.

Compartment : Detergent for the main wash, water softener, pre-soaking agent, bleach and

stain removal product.

Compartment : Additives, e.g. fabric softener or former (ﬁll no higher than lower edge (MAX)

of “A”)

BASIC INSTRUCTIONS

1. Load your laundry into the washing machine.

Do not overload the washing machine. To determine the load capacity for each type of

laundry, refer to the chart on page 24.

• Make sure that laundry is not caught in the door, as this may cause a water leak.

• Washing detergent may remain in the front rubber part of the washer after a wash cycle.

Remove any remaining detergent, as they may cause a water leak.

• Do not wash water-proofed items.

2. Close the door until it latches.

3. Turn the power on.

4. Add detergent and additives to the dispenser drawer.

5. Select the appropriate cycle and options for the load.

The Wash Indicator light will illuminate and the estimated cycle time will appear in the display.

6. Press the Start/Pause button.

WARNING

WD8122CVB-02574C_EN.indd 17 2008-06-05 ¿ÀÈÄ 2:09:42

18_ washing a load of laundry

USING THE CONTROL PANEL

DIGITAL GRAPHIC

DISPLAY

Displays the remaining wash cycle time, all cycle information, and error

messages.

CYCLE SELECTOR

Select the tumble pattern and spinning speed for the cycle.

For detailed information, refer to “Washing clothes using the cycle

selector”.

Cottons - For averagely or lightly soiled cottons, bed linen, table linen,

underwear, towels, shirts, etc.

Blanket - Cotton bedding, bed linen, bed sheet, duvet cover, pillow

cover etc.

Quick - This course is used for small amounts of laundry, relatively clean

laundry, or frequently used laundry in a short period of time.

Delicate - This course is used to wash delicate clothing, such as

lingerie, that is easily deformed or damaged.

Towel - This course is useful for washing towels effectively.

Wool

- Only for machine-washable wool.

The wool wash cycle of this machine has been approved by

Woolmark for the washing of machine-washable Woolmark

products provided that the products are washed according to

the instructions on the garment label and those issued by the

manufacturer of this washing machine, M0509 (Certiﬁcate Number

issued by IWS NOM INEE Co., Ltd.)

Air Wash

- This course is useful for removing bad odors. Turning the

Cycle Selector cycles through the following operating modes.

Knit

→

Coat

→

Bedding

→

Allergy Free

Rinse + Spin - This is useful for laundry that only needs rinsing for

adding fabric softener that is added during a rinse.

Clean Tub - Use this function to maintain wash tub clean and sanitary.

SILVER NANO

SELECTION BUTTON

Silver Nano water is supplied during the wash cycle as well as during

the last rinse cycle, removing bacteria as well as giving protection from

bacterial growth for up to one month.

DELAY END

SELECTION BUTTON

Press this button repeatedly to cycle through the available Delay End

options (max 19 hours in one hour increments).

The hour displayed indicates the time when the wash cycle will be

ﬁnished.

washing a load of laundry

1

2

3

4

5

4

3

6

8

9

7

11

10

12

1

2

1

WD8122CVB-02574C_EN.indd 18 2008-06-05 ¿ÀÈÄ 2:09:42

washing a load of laundry _19

02 WASHING A LOAD OF LAUNDRY

TEMPERATURE

SELECTION BUTTON

Press this button repeatedly to cycle through the available water

temperature options:

(Cold Water , 30 ˚C, 40 ˚C, 60 ˚C, 75 ˚C and 95 ˚C).

RINSE SELECTION

BUTTON

Press this button to add additional rinse cycles. The maximum number

of rinse cycles is ﬁve.

SPIN SELECTION

BUTTON

Press the button repeatedly to cycle through the available speeds for the

spin cycle.

“No spin ” - The laundry remains in the drum and no spin cycle is

performed after the ﬁnal drain.

DRY SELECTION

BUTTON

Pressing the button cycles through the following options.

Normal

→

Extra

→

Iron

→

Light

→

Time (30min

→

1:00min

→

1:30min

→

2:00min

→

2:30min)

“Normal ” - Select to dry laundry automatically by detecting the

amount and weight of the laundry. Select this to dry cotton clothing such

as cotton trousers, T-shirts, and cotton underwear.

“Extra ” - Select this to dry cotton clothing completely. (Thick clothes

such as blue jeans, towels, sports clothes, etc.)

“Iron ” - Finishes the dry cycle in a moist state appropriate for Ironing.

“Light ” - Dry clothing which may become deformed at high

temperatures at a low temperature. (Mixed fabrics and synthetic ﬁbers

such as polyester and nylon.)

“Time ” - Dry the laundry for the speciﬁed period of time.

• You must avoid washing laundry that may not be dried as it may

be deformed even at low temperatures.

• The Normal, Extra, Iron and Light Dry options detect the weight

of the laundry in order to display an accurate drying time and dry

them more completely.

• The drying conditions may differ depending on the type and the

amount of laundry.

STOP&ADD

SELECTION BUTTON

Select this to add the laundry amid the process (See “Stop&Add” on

page 20).

PREWASH

SELECTION BUTTON

Press this button to select pre-wash. Pre-wash means a preliminary

wash that is performed for 10 minutes before the main wash.

Pre-wash is effective for highly soiled laundry.

Pre-wash is only available for: Cottons, Blanket, and Towel.

START/PAUSE

SELECTION BUTTON

Press to pause and restart a cycle.

POWER BUTTON

Press it once to turn your washing machine on, press it again to turn

your washing machine off.

If the washing machine is left on for more than 10 minutes without any

buttons being touched, the power automatically turns off.

5

6

7

8

9

10

11

12

WD8122CVB-02574C_EN.indd 19 2008-06-05 ¿ÀÈÄ 2:09:44

20_ washing a load of laundry

Child lock

The Child Lock function allows you to lock the buttons so that

the wash cycle you’ve chosen can’t be changed.

Activating/Deactivating

If you want to activate or deactivate the Child Lock function,

press the Temp.

and Rinse buttons at the same time for

3 seconds. “Child Lock ” will be lit when this feature is

activated.

When the Child Lock function is activated, only the

Power button works. The Child Lock function remains

on even after the power is turned on and off or after the

disconnecting and reconnecting the power cord.

Delay end

You can set the washing machine to ﬁ nish your wash automatically at a later time, choosing a

delay of max 19 hours (in 1 hour increments). The hour displayed indicates the time at which the

wash will be ﬁ nished.

1. Manually or automatically set your washing machine according to the type of laundry you are

washing.

2. Press the Delay End button repeatedly until the delay time is set.

3. Press the Start/Pause button. The “Delay End” indicator will be lit, and the clock will begin

counting down until it reaches the set time.

4. To cancel a Delay End function, press the Power button and then turn the washing machine

on again.

Stop&Add

When the washing machine is working, the door is locked, and the “Stop&Add” lamp is off,

you will not be able to add laundry. You can only add laundry when the Stop&Add lamp is

illuminated.

1. Press the Stop&Add button.

The washing machine will automatically pause.

2. Wait about 30 seconds and check the state of “Stop&Add” lamp.

• Blinking: The water in the washing machine is drained down to the safety level for the

additional laundry to be added.

• Off: Adding laundry is possible.

3. Add the laundry.

4. Press the Start/Pause button.

• Avoid adding laundry when the machine has foamed up or is ﬁ lled with water. Otherwise,

the foam or water may leak from the door. Check before opening the door.

• We recommend that you select the Stop&Add function 5 minutes before a cycle is

performed.

• If the internal temperature is higher than 55 ˚C during the wash cycle or 70 ˚C during the

drying cycle, the Stop&Add function cannot be selected.

• Do not open the door by force as it may result in injury or damage the washer.

washing a load of laundry

3 SEC.

WARNING

WD8122CVB-02574C_EN.indd 20 2008-06-05 ¿ÀÈÄ 2:09:45

ページが読み込まれています...

Samsung WD8122CVB/XSP ユーザーマニュアル

Samsung WD8122CVB/XSP ユーザーマニュアル

関連論文

その他のドキュメント