Philips S8880/68 ユーザーマニュアル

ブランド: Philips

モデル: S8880/68

カテゴリー: メンズシェーバー

タイプ: ユーザーマニュアル

8000 series

S8860

www.philips.com/support/ifu

HQ8508

HQ87

10 11

empty page before TOC

English 6

简体中文

English

General description (Fig.1)

1 Protection cap for cleansing brush attachment

2 Click-on cleansing brush attachment

3 Protection cap for shaving unit

4 Click-on shaving unit

5 On/off ring

6 On/off indications

7 Handle

8 Battery low indicator

9 Charging pad

10 Charging platform

11 Charging indicator

12 USB plug

13 Socket for USB plug

14 Supply unit

15 Cleaning brush

16 Click-on beard styler attachment

17 Comb for beard styler attachment

Important safety information

Read this important information carefully before

you use the appliance and its accessories and save

it for future reference. The accessories supplied

may vary for different products.

Danger

- Keep the supply unit dry.

English

Warning

- The appliance is a Class III

construction.

- To charge the battery, only use

the detachable supply unit

(supply unit, type HQ87.

Charging pad, type HQ8508)

provided with the appliance.

- This appliance can be used by

children aged from 8 years and

above and persons with

reduced physical, sensory or

mental capabilities or lack of

experience and knowledge if

they have been given

supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved. Children

shall not play with the

appliance. Cleaning and user

maintenance shall not be made

by children without supervision.

English

- Always check the appliance

before you use it. Do not use

the appliance if it is damaged,

as this may cause injury. Always

replace a damaged part with

one of the original type.

- Do not open the appliance to

replace the rechargeable

battery.

Caution

- Never immerse the charging pad in water.

- Always make sure the charging pad is

completely dry before you connect it to the

wall socket.

- Never use water hotter than 60°C to rinse

the shaver.

- Only use this appliance for its intended

purpose as shown in the user manual.

- The charging pad is not intended for use in

a car. It may interfere with the automotive

electronic systems.

- For safety reasons, do not use the shaver

while you drive a car.

- For hygienic reasons, the appliance should

only be used by one person.

English

- Never use compressed air, scouring pads,

abrasive cleaning agents or aggressive

liquids such as petrol or acetone to clean

the appliance.

- Water may trickle out of the shaver after

your rinse it. This is normal and not

dangerous because all electronics are

enclosed in a sealed power unit inside the

shaver.

- Do not use the supply unit in or near wall

sockets that contain an electric air freshener

to prevent irreparable damage to the supply

unit.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic fields.

General

- This shaver is waterproof. It is suitable for use in

the bath or shower and for cleaning under the

tap.

- The supply unit is suitable for mains voltages

ranging from 100 to 240 volts.

- The supply unit transforms 100-240 volts to a

safe low voltage of less than 24 volts.

English

Charging

Charge the appliance before you use it for the first

time and when the battery low indicator indicates

that the battery is almost empty.

Note: The shaver is Qi compliant.

Charging takes approx. 2 hours. A fully charged

appliance has a operating time of up to 30

minutes.

Tip: If your smartphone is compliant with Qi

charging,you can also use the charging pad to

charge your smartphone.

1 Put the supply unit in the wall socket and place

the appliance onto the charging platform of the

charging pad.

The charging pad bleeps when the appliance

is correctly placed onto the charging

platform.

2 After charging, remove the supply unit from the

wall socket.

Battery charging

When the shaver is charging, the charging indicator

flashes white.

Battery low

When the battery is almost empty, the battery low

indicator flashes orange.

English

Battery fully charged

When the battery is fully charged, the charging

indicator lights up white continuously.

Using the appliance

Switching the appliance on and off

1 To switch on the appliance, turn the on/off ring

anticlockwise to the 'on' indication (I).

2 To switch off the appliance, turn the on/off ring

clockwise to the 'off' indication (0).

Shaving

Skin adaptation period

Your first shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system. To allow

your skin to adapt to this new appliance, we advise

you to shave regularly (at least 3 times a week) and

exclusively with this appliance for a period of 3

weeks.

Dry shaving

1 Switch on the appliance.

2 Move the shaving heads over your skin in

circular movements to catch all hairs growing in

different directions. Make sure each shaving

head is fully in contact with the skin. Exert

gentle pressure for a close, comfortable shave.

English

Note: Do not press too hard, this can cause skin

irritation.

3 Switch off the appliance.

4 Clean the appliance after every use.

Wet shaving

For a more comfortable shave, you can also use

this appliance on a wet face with shaving foam or

shaving gel.To shave with shaving foam or shaving

gel, follow the steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure

that the shaving unit glides smoothly over your

skin.

4 Switch on the appliance.

5 Move the shaving heads over your skin in

circular movements to catch all hairs growing in

different directions. Make sure each shaving

head is fully in contact with the skin. Exert

gentle pressure for a close, comfortable shave.

Note: Rinse the shaving unit regularly to ensure

that it continues to glide smoothly over your

skin.

6 After use, rinse and dry your face gently and

clean the appliance (see 'Cleaning and

maintenance').

Note: Make sure you rinse all foam or shaving

gel off the appliance.

English

Using click-on attachments

Removing or attaching the click-on attachment

1 Make sure the appliance is switched off.

2 Pull the attachment straight off the appliance.

Note: Do not twist the attachment while you

pull it off the appliance.

3 Insert the lug of the click-on attachment into

the slot in the top of the appliance. Then press

down the attachment to attach it to the

appliance (' click').

Using the click-on beard styler attachment with comb

You can use the beard styler attachment with the

comb attached to style your beard at one fixed

setting, but also at different length settings. You

can also use it to pre-trim any long hairs before

shaving for a more comfortable shave.

The length settings on the beard styler attachment

correspond to the remaining hair length after

cutting and range from 1 to 5mm (3/64 - 3/16in).

1 Attach the attachment to the appliance ('click').

Slide the comb straight into the guiding grooves

on both sides of the beard styler attachment

(‘click’).

English

2 Press the length selector and then push it to

the left or right to select the desired hair length

setting.

3 Switch on the appliance.

4 Move the appliance upwards while you exert

gentle pressure. Make sure the front of the

comb is in full contact with the skin.

5 Clean the attachment after use.

Using the click-on beard styler attachment without

comb

You can use the beard styler attachment without

the comb to contour your beard, moustache,

sideburns or neckline to a length of 0.5mm (1/32

in).

1 Pull the comb off the beard styler attachment.

Note: Grab the comb in the center to pull it off

the beard styler attachment. Do not pull at the

sides of the comb.

2 Switch on the appliance.

3 Hold the beard styler attachment perpendicular

to the skin and move the appliance downwards

while you exert gentle pressure.

4 Clean the attachment after use.

Using the click-on cleansing brush attachment

Use the rotating cleansing brush with your daily

cleansing cream. The cleansing brush removes oil

English

and dirt, contributing to a healthy and oil-free skin.

We advise you to use it no more than twice a day.

Do not use the appliance on damaged or irritated

skin or on wounds.

1 Make sure the appliance is switched off.

2 Remove the shaving unit from the appliance

and attach the click-on cleansing brush.

3 Moisten the cleansing brush with water.

Caution: Do not use the appliance with a dry

brush, as this can irritate the skin.

4 Moisten your face with water and apply a

cleanser to your face.

5 Switch on the appliance.

20 sec.

6 Gently move the brush across your skin from

the nose towards the ear. Do not push the

attachment to hard onto the skin to make sure

the treatment remains comfortable.

20 sec.

7 After approx. 20 seconds, move the appliance

to your other cheek and start cleansing this part

of your face.

Do not cleanse the sensitive area around your

eyes.

English

20 sec.

8 After approx. 20 seconds, move the appliance

to your forehead and start cleansing this part of

your face. Gently move the brush head from left

to right.

Note: We advise you to not overdo the

cleansing and to not cleanse any zone longer

than 20 seconds.

9 After the treatment, rinse and dry your

face.Your face is now ready for the next step of

your daily skincare routine.

10 Clean the cleansing brush after use (see

'Cleaning the click-on attachment').

Cleaning and maintenance

Cleaning the appliance

Clean the shaver after every shave for optimal

performance.

1 Switch off the appliance.

2 Rinse the shaving unit under a warm tap.

Be careful with hot water. Always check if the

water is not too hot, to prevent burning your

hands.

3 Pull the shaving head holder off the bottom

part of the shaving unit.

English

4 Rinse the shaving head holder under a warm

tap.

5 Carefully shake off excess water and let the

shaving head holder air-dry completely.

Never dry the shaving unit with a towel or

tissue, as this may damage the shaving heads.

6 Reattach the shaving head holder to the

bottom part of the shaving unit ('click').

Cleaning the charging pad

1 Wipe the surface of the charging pad with a

slightly damp cloth to remove any dirt.

2 Dry the surface with a dry cloth after cleaning.

Caution: Always make sure the charging pad is

completely dry before connecting to a power

outlet.

Thorough cleaning

We advise you to clean the shaving heads

thoroughly once a month or when the shaver does

not shave as well as it used to.

Note: The shaving heads are locked by a blue or an

orange retaining ring.

English

Follow the correct instructions.

1 Switch off the shaver.

2 Pull the shaving head holder off the bottom

part of the shaving unit.

3 Rinse the hair chamber and shaving head

holder under the tap.

4 Turn the retaining ring anticlockwise and lift it

off the shaving head.

Repeat this process for the other retaining rings.

Place them aside in a safe place.

English

5 Remove the shaving heads from the shaving

head holder. Each shaving head consists of a

cutter and guard.

Note: Do not clean more than one cutter and

guard at a time, since they are all matching sets.

If you accidentally put a cutter in the wrong

shaving guard, it may take several weeks before

optimal shaving performance is restored.

6 Clean the cutter and guard under the tap.

7 Shake off excess water.

8 Put the cutter back into the guard.

9 Place the shaving heads in the shaving head

holder.

Note: Make sure the notches on both sides of

the shaving heads fit exactly onto the

projections in the shaving head holder.

10 Blue retaining ring: Place the retaining ring on

the shaving head and turn it clockwise to

reattach the retaining ring.

Place the arrows on the ring in line with the

projections in the shaving head holder. Turn the

ring clockwise until it clicks to indicate that the

ring is fixed.

English

- Orange retaining ring: Place the retaining ring

on the shaving head and turn it clockwise to

reattach the retaining ring. Repeat this process

for the other retaining rings.

Each retaining ring has two recesses that fit

exactly into the projections of the shaving head

holder. Turn the ring clockwise until your hear a

click to indicate that the ring is fixed.

Hold the shaving head holder in your hand

when you reinsert the shaving heads and

reattach the retaining rings. Do not place the

shaving head holder on a surface when you do

this, as this may cause damage.

11 Attach the shaving head holder to the bottom

part of the shaving unit (‘click’).

Cleaning the click-on attachment

Cleaning the click-on cleansing brush

1 Make sure the appliance is switched off.

2 Detach the brush head from the attachment

holder.

Note: Do not twist the brush head while you

pull it off the brush base.

3 Clean both parts thoroughly with warm water

and mild soap.

4 Dry the cleansing brush with a towel.

Cleaning the beard styler attachment

Clean the beard styler attachment after each use.

English

ページが読み込まれています...

Philips S8880/68 ユーザーマニュアル

ブランド: Philips

モデル: S8880/68

カテゴリー: メンズシェーバー

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

他の言語で

English: Philips S8880/68 User manual

Philips S8880/68 ユーザーマニュアル

Philips S8880/68 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント