Samsung HW-N300 クイックスタートガイド

HW-N300

USER MANUAL

ENG - 2

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - 3

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

ABOUT THIS MANUAL

The user manual has two parts: this simple paper

USER MANUAL and a detailed FULL MANUAL you

can download.

USER MANUAL

See this manual for safety instructions,

product installation, components,

connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on

Samsung’s on-line customer support centre by

scanning the QR code. To see the manual on

your PC or mobile device, download the

manual in document format from Samsung’s

website. (http://www.samsung.com/support)

Design and specications are subject to change

without prior notice.

ENG - 4

CONTENTS

01 Checking the Components 6

Inserting battery into the Remote Control ------------------------- 6

02 Product Overview 7

Front / Right Side Panel of the Soundbar ------------------------- 7

Bottom Panel of the Soundbar ------------------------- 8

03 The Remote Control 9

Adjusting the Soundbar volume with a TV remote control

-------------------------

10

04 Connecting the Soundbar 12

Connecting Electrical Power

-------------------------

12

05 Connecting to a TV 13

Connecting using an Optical Cable

-------------------------

13

Connecting a TV or Bluetooth Device via Bluetooth

-------------------------

15

06 Connecting an External Device 17

Connecting using an Optical Cable

-------------------------

17

Connecting using an Analogue Audio (AUX) Cable

-------------------------

18

07 Connecting a USB Storage Device 19

Setting Repeat Play Options

-------------------------

20

Software Update

-------------------------

20

ENG - 5

08 Installing the Wall Mount (Optional) 21

Installation Precautions

-------------------------

21

Wall mount Components

-------------------------

21

09 Troubleshooting 24

10 Licence 25

11 Open Source Licence Notice 25

12 Important Notes About Service 25

13 SpecicationsandGuide 26

Specications

-------------------------

26

ENG - 6

01 CHECKING THE COMPONENTS

Soundbar Main Unit Power Cord Remote Control / Battery

(AAA x 1, Not available in some

locations)

• User Manual / Warranty Card / Regulatory Guide (Not available in some locations).

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label : Bottom of the Soundbar Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

Inserting battery into the Remote Control

Match the polarity of the battery to the symbols on the battery compartment.

1

3

2

ENG - 7

02 PRODUCT OVERVIEW

Front / Right Side Panel of the Soundbar

AUX IN

POWER

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

AUX IN

POWER

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

Volume

Power

Position the product so that the

SAMSUNG logo is located on the top.

Front of the Soundbar

Right Side of the Soundbar

󰟳

󰟴

󰟳

LED

indicator

The LED Indicator ashes, glows, or changes colour depending on the Soundbar's current

mode or status. The colour of the LED indicator and the number of lights indicate the active

mode as described below.

W

White LED

B

Blue LED

R

Red LED

G

Green LED

Mode

Remote control

Button

LED indicator

D.IN

W

Bluetooth

B

Connected status

B

Slow-Blinking

Disconnected status

Bluetooth

pairing

5 Sec

B

Fast-Blinking

AUX

W W

USB

W W W

󰟴

Source

Selects the source input mode. (D.IN / Bluetooth / AUX / USB)

• To turn on “Bluetooth pairing” mode, change the source to “Bluetooth” mode and then

press and hold the button for more than 5 seconds.

ENG - 8

Bottom Panel of the Soundbar

Bottom of the Soundbar

AUX IN

POWER

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

POWER

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

POWER

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

󰟳

󰟵

󰟴

󰟶

󰟳

POWER Connect the Soundbar's AC power cord.

󰟴

AUX Connect to the Analogue output of an external device.

󰟵

D.IN Connect to the digital (optical) output of an external device.

󰟶

USB Connect a USB device here to play music les on the USB device through the Soundbar.

ENG - 9

03 THE REMOTE CONTROL

• The images, buttons, and functions of the remote control may differ depending on the model.

Turns the Soundbar on and off.

Press this button to mute the sound.

Press it again to unmute the sound.

Press this button to turn off the Auto

Power Link function.

Press to enter the "USB" mode.

Push this button up or down to

adjust the bass volume within a -6 to

+6 range.

Press to enter the "AUX" mode.

Press the

button to select the

previous music le.

Press the

button to play/pause

a music le.

Press the

button to select the

next music le.

Press to select the desired

sound effect by choosing

SURROUND or STANDARD.

Push this button up or down to

adjust the volume.

Press this button to turn on the

Auto Power Link function. See

"Connecting using an Optical

Cable" on pages 13 and 14

for details.

Press to enter the “D.IN” mode.

Press to enter the “Bluetooth”

mode.

You can use your Bluetooth

device in this mode.

To pair a new Bluetooth device,

press and hold this button for

5 seconds or more.

ENG - 10

Adjusting the Soundbar volume with a TV remote control

If you have a Samsung TV, you can adjust the Soundbar’s volume using the IR remote

control that came with your Samsung TV.

First use the TV menu to set the TV audio on your Samsung TV to external speakers, then use your

Samsung remote to control the Soundbar’s volume. For more information, see the TV’s user manual.

The default mode for this function is control by a Samsung TV.

1. If your TV is not a Samsung TV and you want your TV’s remote to control the Soundbar’s volume,

you can change the settings of this function by pressing and holding the BASS button

repeatedly. To have your TV’s remote adjust the Soundbar’s volume, follow Steps 1 through 3

below.

2. If you want to turn off this function completely, follow Steps 1 and 2.

Mode Remote control Button LED indicator

1.

Turn off

All LED’s Off

2.

“Off” mode

5 Sec

W W W W

Blinking

3.

“All TV” mode

5 Sec

W W W W

Blinking

4.

“Samsung TV” mode

(Default mode)

5 Sec

W W W W

Blinking

– Each time you press the BASS button and hold it for 5 seconds, the mode switches in the

following order:

“Samsung TV” (Default mode) → “Off” → “All TV”.

– The LED’s blink for 3~4 seconds, then return to the standby power off mode.

– This function may not be available, depending on your TV`s remote control.

– For a list of manufacturers that support this feature, refer to the FULL MANUAL of your Soundbar

on the Samsung web site (www.samsung.com/support).

ENG - 11

– This volume control function works with IR TV remotes only. It does not work with Bluetooth TV

remotes (remotes that require pairing).

NOTE

– Not all TV manufacturers support this feature. For a list of manufacturers that do support this

feature, refer to the FULL MANUAL of your Soundbar on the Samsung web site

(www.samsung.com/support).

ENG - 12

04 CONNECTING THE SOUNDBAR

Connecting Electrical Power

• For information about the required electrical power and power consumption, refer to the label

attached to the product. (Label : Bottom of the Soundbar Main Unit)

AUX IN

POWER

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

POWER

Power Cord

Electrical Outlet

Bottom of the Soundbar Main Unit

ENG - 13

05 CONNECTING TO A TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to selected Samsung TVs, you can control the Soundbar using the

TV’s remote control.

– This feature is supported by 2017 and later Samsung Smart TVs that support Bluetooth when

you connect the Soundbar to the TV using an optical cable.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Connecting using an Optical Cable

Step 1. Connect an Optical Cable

USB (5V 0.5A)

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

OPTICAL OUT

Optical Cable

(not supplied)

Bottom of the Soundbar

NOTE

– When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on

your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the

setting on the TV is changed, you will experience better sound quality. (The TV menu may use

different words for Dolby Digital and PCM depending on the TV manufacturer.)

ENG - 14

Step 2. Change the Soundbar’s mode to D.IN

Right Side of the Soundbar

(OR)

W

Auto Power Link

This Function automatically turns on the Soundbar when the TV is turned on if the Soundbar is

connected to the TV by an Optical Cable (not supplied).

Press the

button on the remote control to turn on this function.

• Auto Power Link is set to ON by default. (To turn off this function, press the button on the

remote control.)

• Depending on the connected device, Auto Power Link may not function.

• This function is only available in the “D.IN” mode.

Mode Remote control Button LED indicator

OFF

W W

R

Blinking

ON

W W

G

Blinking

ENG - 15

Connecting a TV or Bluetooth Device via Bluetooth

Step 1. Change the Soundbar mode to “Bluetooth Pairing”

B

Fast-Blinking

5 Sec

Step 2. Select the Soundbar in your TV’s or Bluetooth device’s Menu

Select

“[AV] Samsung Soundbar Nxxx N-Series”

Bluetooth device

(OR)

Bluetooth menu

NOTE

– You cannot connect more than one TV or Bluetooth device at a time.

Step 3. Check the Soundbar’s status

The blue LED should not be blinking once the Bluetooth connection is complete.

B

If the TV or device fails to connect

• If a previously connected Soundbar listing appears in the device list of your TV or Bluetooth device,

delete it. (e.g. “[AV] Samsung Soundbar Nxxx N-Series”)

• Then repeat steps 1 through 3.

ENG - 16

Disconnecting the Soundbar from the TV

Press the button on the right side panel or on the remote control and switch to any mode but

“Bluetooth”.

• Disconnecting takes time because the TV must receive a response from the Soundbar.

(The time required may differ, depending on the TV model.)

• To cancel the automatic Bluetooth connection between the Soundbar and TV, press and hold

button for 5 seconds in “Bluetooth” mode. TV Connect is turned OFF.

• To turn TV Connect back on, press and hold the button for 5 seconds with the Soundbar in

“Bluetooth” mode.

• TV Connect is set to ON by default.

Mode Remote control Button LED indicator

TV Connect-OFF

5 Sec

B

W W

R

Blinking

TV Connect-ON

5 Sec

B

W W

G

Blinking

NOTES

– If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

– In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the

Soundbar and the Bluetooth device exceeds 10 meters.

– The Soundbar automatically turns off after 5 minutes in the Ready state.

– The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If several Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

– Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 17

06 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via an optical cable or analogue cable to play the external device’s sound

through the Soundbar.

Connecting using an Optical Cable

Step 1. Connect using an Optical Cable

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

OPTICAL OUT

Bottom of the Soundbar

Optical Cable

(not supplied)

BD / DVD player / Set-top box /

Game console

Step 2. Change the Soundbar’s mode to D.IN

Right Side of the Soundbar

(OR)

W

ENG - 18

Connecting using an Analogue Audio (AUX) Cable

Step 1. Connect using an Analogue Audio (AUX) Cable

AUX IN

DIGITAL AUDIO IN

(OPTICAL)

- AUDIO -

R L

Bottom of the Soundbar

Audio (AUX) Cable

(not supplied)

BD / DVD player / Set-top box /

Game console

Step 2. Change the Soundbar’s mode to AUX

Right Side of the Soundbar

(OR)

W W

ENG - 19

07 CONNECTING A USB STORAGE DEVICE

Step 1. Connect a USB Drive

USB (5V 0.5A)

Bottom of the Soundbar

NOTE

– The Soundbar automatically turns off (Auto Power Off) if you do not connect a USB device to the

Soundbar within 5 minutes.

Step 2. Change the Soundbar’s mode to USB

Right Side of the Soundbar

(OR)

W W W

ENG - 20

Setting Repeat Play Options

When the Soundbar is in “USB” mode, each time you press the button the “USB” mode changes

how it plays tracks in the following order: Repeat - Off > Repeat - 1 song > Repeat - All songs >

Repeat - Random. See the table below for details.

Mode Remote control Button LED indicator

Repeat - Off

W W W

Repeat - 1 song

W W W

Blinking

Repeat - All songs

W W W

Blinking

Repeat - Random

W W W

Blinking

Software Update

SamsungmayofferupdatesfortheSoundbar’ssystemrmwareinthefuture.

If an update is offered, you can update the rmware by connecting a USB device with the rmware

update stored on it to the USB port on your Soundbar. For more information about how to download

update les, go to the Samsung Electronics website at (www.samsung.com



Support).

Then, enter or select the model number of your Soundbar, select the Software & Apps option, and then

Downloads. Note that the option names can vary.

ページが読み込まれています...

Samsung HW-N300 クイックスタートガイド

Samsung HW-N300 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント