简体中文
10
充电器上的符号
使用设备前,请仔细阅读本手册。
本工具采用双重绝缘,因此无需接地线。
请务必检查电源电压是否与铭牌上的电压
一致。
充电底座仅供室内使用。
设备上的标签
设备上的下列符号会和日期码一起显示:
仅能与 S003AQ 15 充电器搭配使用
部件名称
本工具包含如下部分或全部部件。
1. 打开/关闭开关(按住)
2. 集尘仓释放按钮
3. 集尘仓
4. 充电器
5. 充电座支架
图 A
6. 湿/干泡沫衬垫
7. 湿/干偏转板
图 B
8. 橡胶清洁器
9. 刷头
10. 细缝吸嘴
安装
壁挂式安装(图 C)
该产品可以安装到墙上,以为设备提供方便的存放
和充电点。
安装到墙上时,请确保安装方法适合墙壁类型并能
承受设备的重量。
标记螺丝孔的位置(在对置于墙上支架上的真空
吸尘器进行充电时电源插座可及的范围内)。
请使用适合墙壁类型并能承受设备重量的螺丝和
插头,将安装支架安装到墙上。
通过将真空吸尘器底座上的孔放到壁装充电座支
架中的挂钩上将设备挂在墙上。
Symbols on the charger
Read all of this manual carefully
before using the appliance.
#
This tool is double insulated;
therefore no earth wire is
required. Always check that the
power supply corresponds to
the voltage on the rating plate.
$
The charging base is intended
for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code:
S003AQ 15
Only use with charger S003AQ 15
Features
This tool includes some or all of the following features.
1. On/off switch (press and hold)
2. Bowl release button
3. Dust bowl
4. Charger
5. Charging bracket
Fig. A
6. Wet/Dry foam insert
7. W
Fig. B
8. Squeegee
9. Brush tool
10. Crevice tool
Installation
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
u Fix the mounting bracket to the wall using appropriate
screws and plugs for the type of wall and weight of the
appliance.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
charging bracket.
Assembly
These models may be supplied with some of the following
accessories:
u A squeege tool (8) for wet use on hard surfaces.
u A brush tool (9) for furniture and stairs.
u
Fitting (Fig. D)
u Insert the appropriate accessory into the front of the appli-
ance. Make sure that the accessory is pushed fully in.
Use
u
10 hours.
u Place the appliance on the charging bracket whenever it is
not in use.
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
Charging the battery (Fig. C)
u Make sure that the appliance is switched off. The battery
will not be charged with the on/off switch (1) pressed.
u Place the appliance on the charging bracket (5).
u Plug in the charger. Switch on at the mains.
u Leave the appliance to charge for at least 21 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
u To switch the appliance on, press and hold the on/off
switch (1).
u To switch the appliance off, release on/off switch (1).
Wet and dry pick up
u For everyday spills of dry material, use your appliance
without the squeegee accessory.
10
Symbols on the charger
Read all of this manual carefully
before using the appliance.
#
This tool is double insulated;
therefore no earth wire is
required. Always check that the
power supply corresponds to
the voltage on the rating plate.
$
The charging base is intended
for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code:
S003AQ 15
Only use with charger S003AQ 15
Features
This tool includes some or all of the following features.
1. On/off switch (press and hold)
2. Bowl release button
3. Dust bowl
4. Charger
5. Charging bracket
Fig. A
6. Wet/Dry foam insert
7. W
Fig. B
8. Squeegee
9. Brush tool
10. Crevice tool
Installation
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
u Fix the mounting bracket to the wall using appropriate
screws and plugs for the type of wall and weight of the
appliance.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
charging bracket.
Assembly
These models may be supplied with some of the following
accessories:
u A squeege tool (8) for wet use on hard surfaces.
u A brush tool (9) for furniture and stairs.
u
Fitting (Fig. D)
u Insert the appropriate accessory into the front of the appli-
ance. Make sure that the accessory is pushed fully in.
Use
u
10 hours.
u Place the appliance on the charging bracket whenever it is
not in use.
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
Charging the battery (Fig. C)
u Make sure that the appliance is switched off. The battery
will not be charged with the on/off switch (1) pressed.
u Place the appliance on the charging bracket (5).
u Plug in the charger. Switch on at the mains.
u Leave the appliance to charge for at least 21 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
u To switch the appliance on, press and hold the on/off
switch (1).
u To switch the appliance off, release on/off switch (1).
Wet and dry pick up
u For everyday spills of dry material, use your appliance
without the squeegee accessory.
10
Symbols on the charger
Read all of this manual carefully
before using the appliance.
#
This tool is double insulated;
therefore no earth wire is
required. Always check that the
power supply corresponds to
the voltage on the rating plate.
$
The charging base is intended
for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code:
S003AQ 15
Only use with charger S003AQ 15
Features
This tool includes some or all of the following features.
1. On/off switch (press and hold)
2. Bowl release button
3. Dust bowl
4. Charger
5. Charging bracket
Fig. A
6. Wet/Dry foam insert
7. W
Fig. B
8. Squeegee
9. Brush tool
10. Crevice tool
Installation
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
u Fix the mounting bracket to the wall using appropriate
screws and plugs for the type of wall and weight of the
appliance.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
charging bracket.
Assembly
These models may be supplied with some of the following
accessories:
u A squeege tool (8) for wet use on hard surfaces.
u A brush tool (9) for furniture and stairs.
u
Fitting (Fig. D)
u Insert the appropriate accessory into the front of the appli-
ance. Make sure that the accessory is pushed fully in.
Use
u
10 hours.
u Place the appliance on the charging bracket whenever it is
not in use.
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
Charging the battery (Fig. C)
u Make sure that the appliance is switched off. The battery
will not be charged with the on/off switch (1) pressed.
u Place the appliance on the charging bracket (5).
u Plug in the charger. Switch on at the mains.
u Leave the appliance to charge for at least 21 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
u To switch the appliance on, press and hold the on/off
switch (1).
u To switch the appliance off, release on/off switch (1).
Wet and dry pick up
u For everyday spills of dry material, use your appliance
without the squeegee accessory.
10
Symbols on the charger
Read all of this manual carefully
before using the appliance.
#
This tool is double insulated;
therefore no earth wire is
required. Always check that the
power supply corresponds to
the voltage on the rating plate.
$
The charging base is intended
for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code:
S003AQ 15
Only use with charger S003AQ 15
Features
This tool includes some or all of the following features.
1. On/off switch (press and hold)
2. Bowl release button
3. Dust bowl
4. Charger
5. Charging bracket
Fig. A
6. Wet/Dry foam insert
7. W
Fig. B
8. Squeegee
9. Brush tool
10. Crevice tool
Installation
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for charging the vac while it is on the wall
bracket).
u Fix the mounting bracket to the wall using appropriate
screws and plugs for the type of wall and weight of the
appliance.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
charging bracket.
Assembly
These models may be supplied with some of the following
accessories:
u A squeege tool (8) for wet use on hard surfaces.
u A brush tool (9) for furniture and stairs.
u
Fitting (Fig. D)
u Insert the appropriate accessory into the front of the appli-
ance. Make sure that the accessory is pushed fully in.
Use
u
10 hours.
u Place the appliance on the charging bracket whenever it is
not in use.
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
Charging the battery (Fig. C)
u Make sure that the appliance is switched off. The battery
will not be charged with the on/off switch (1) pressed.
u Place the appliance on the charging bracket (5).
u Plug in the charger. Switch on at the mains.
u Leave the appliance to charge for at least 21 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
u To switch the appliance on, press and hold the on/off
switch (1).
u To switch the appliance off, release on/off switch (1).
Wet and dry pick up
u For everyday spills of dry material, use your appliance
without the squeegee accessory.
10
组装
附件(图 B)
不同型号的吸尘器将配有下列相应配件:
橡胶清洁器 (8),用于在硬质表面上清理液体。
针对家具和楼梯的刷头 (9)。
针对狭窄空间的细缝吸嘴 (10)。
安装(图 D)
将合适的配件插入设备前部。请确定已将配件完
全推入,锁定到位。
使用
首次使用之前,必须让电池至少充电 10 个小时。
不使用时,请将设备放在充电座支架上。
警告!充电前,请确保将设备里的所有液体倒空并
彻底干燥,以避免设备在充电时出现损坏。
为电池充电(图 C)
确保设备开关关闭。按下打开/关闭开关 (1) 时,
电池将无法充电。
将设备放在充电座支架 (5) 上。
插入充电器。打开电源。
让设备至少充电 21 个小时。
充电时,充电器可能会变热。这是正常现象,并不
表示出现问题。设备可以长期连接充电器。
警告!请勿在环境温度低于 10°C 或高于 40°C 的情
况下为电池充电。
打开和关闭(图 E)
要打开设备电源,请按下打开/关闭开关 (1)。
要关闭设备电源,请放开打开/关闭开关 (1)。
湿与干吸取
若要使用设备清理日常溢漏干燥物质,请不要使
用橡胶清洁器。
警告!您的产品只适用于清理少量的溢漏物质。
本设备也可用于吸取日常溢漏液体。在无吸收性
硬质表面上,请使用橡胶清洁器进行清洁。在
如地毯等具吸收性的表面上,若不使用橡胶清洁
器,吸取液体的效果会更佳。
若要在硬质表面上吸取液体时获得最佳效果,请
将橡胶清洁器插入集尘仓吸尘嘴开口。
若要获得该配件的最佳使用效果,请以 45° 角握
紧设备,然后慢慢将它拉向您。
请不要让尘埃溢满集尘仓的吸入槽。如果集尘仓
中有任何液体,不要将设备倒置、侧放、将吸尘
嘴朝上,或过度摇晃设备。
吸取液体之后,请立即清洗设备和过滤器。设备
使用后应当适当清洗,以避免发霉。