© 2017 Koninklijke Philips N.V.
保留所有权利
3140 035 41155
在以下网站注册并获得支持
www.philips.com.cn/welcome
HP8668
EN User manual
ZH-CN 用户手册
English
Congratulations on your purchase, and welcome to Philips!
To fully benet from the support that Philips oers, register
your product at www.philips.com.cn/welcome.
1 Important
Read this user manual carefully before you use the
appliance and keep it for future reference.
• WARNING: Do not use this
appliance near water.
• When the appliance is used in
a bathroom, unplug it after use
since the proximity of water
presents a risk, even when the
appliance is switched o.
• WARNING: Do not use
this appliance near
bathtubs, showers,
basins or other vessels
containing water.
• Always unplug the appliance
after use.
• If the appliance overheats,
it switches o automatically.
Unplug the appliance and let
it cool down for a few minutes.
Before you switch the appliance
on again, check the grilles to
make sure they are not blocked
by u, hair,etc.
• If the mains cord is damaged,
you must have it replaced
by Philips, a service centre
authorised by Philips or similarly
qualied persons in order to
avoid a hazard.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved. Children
shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
• For additional protection, we
advise you to install a residual
current device (RCD) in the
electrical circuit that supplies
the bathroom. This RCD must
have a rated residual operating
current not higher than 30mA.
Ask your installer for advice.
• Before you connect the
appliance, ensure that the
voltage indicated on the
appliance corresponds to the
local power voltage.
• Do not use the appliance
for any other purpose than
described in this manual.
• Never block the air grilles.
• When the appliance is
connected to the power, never
leave it unattended.
• Never use any accessories or
parts from other manufacturers
or that Philips does not
specically recommend.
If you use such accessories or
parts, your guarantee
becomes invalid.
• Do not wind the mains cord
round the appliance.
• Wait until the appliance has
cooled down before you store it.
• Pay full attention when using
the appliance since it could be
extremely hot. Only hold the
handle as other parts are hot
and avoid contact with the skin.
• Avoid the mains cord from
coming into contact with the hot
parts of the appliance.
• Do not use the appliance on
articial hair.
• Never cover the appliance
with anything (e.g. a towel or
clothing) when it is hot.
• Do not operate the appliance
with wet hands.
• Keep the metal barrel clean
and free of dust and styling
products such as mousse, spray
and gel.
• The metal barrel has coating.
This coating might slowly wear
away over time. However, this
does not aect the performance
of the appliance.
• If the appliance is used on
color-treated hair, the metal
barrel may be stained.
• Always return the appliance to
a service centre authorized by
Philips for examination or repair.
Repair by unqualied people
could result in an extremely
hazardous situation for the user.
• Do not insert metal objects into
openings to avoid
electric shock.
• Do not pull on the power cord
after using. Always unplug the
appliance by holding the plug.
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic elds.
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an ocial collection point for recycling. By doing
this, you help to preserve the environment.
2 Before styling your hair
Note: Always let the appliance and attachments cool down
before you connect or disconnect the attachments.
Remarks: Depending on the dampness of the hair, the
duration for each strand would dier. A longer duration is
needed if hair is damper than recommended.
1 Select your desired attachment ( d, g, h ) and x it onto
the handle ( e ) of the styler.
• Press the release button ( b ) to remove the attachment
when it cools down.
2 Connect the plug to a power supply socket.
3 Slide the airow switch ( c ) to strong and warm airow
for fast drying, warm airow for gentle drying and styling
to prevent your hair from overheating, and cool airow
for xing your style.
3 How to style your hair
We recommend that you practice using the appliance two or
three times so you can get used to how it works.
( A ) Nozzle attachment ( h )
1 Select the nozzle ( h ) and x it onto the handle ( e ).
2 ( Fig. 5-A ) Dry your hair with suitable settings ( c ).
( B ) Air curl attachment ( d )
Tips and Tricks
Refer to the Quick Start Guide for detailed usage
instructions.
• ( Fig.2 ) There are dierent points where the curling
attachment can be xed. For your convenience, you can
change the position according to the way you hold
the appliance
• Pre-dry your hair, including the roots, before using the
product. For optimal results, hair should be 80%–90% dry
• Comb hair thoroughly and ensure that there are
no tangles
• Separate hair into sections. Keep all unused hair away
from the opening. Make sure that there are no stray or
loose strands near the opening
• Start curling from the back of the head
• Turn on the device by selecting hot airow setting .
( Fig.3 ) Check the opening is clear before inserting the
hair. Press the rotating button to make sure there is
nothing blocking the opening
• Twist the hair once to make it easier to put into
the opening
• Place the opening on your hair where you want the curls
to start. Do not place too close to the roots
• Hold the hair strands taut when putting into the opening
• Do not immediately release the rotation button when
the hair can no longer be seen at the opening. Allow the
rotation to continue for another 10 seconds to ensure that
the hair is completely inside the chamber
• Check that the ends of the hair strands remain enclosed
within the chamber and no stray hair is sticking out
• ( Fig. 4 ) If hair becomes trapped, switch o the device.
Gently remove any trapped hair in thin strands, section
by section, until all of the hair is freed. Alternatively, you
can press the side buttons ( i ) of the air curl attachment
to remove the top cover of the attachment and release
trapped hair
( C ) Brush attachment ( g )
• Make waves/volume in the hair ( Fig.5-B )
1 Place the brush ( g ) at the hair tips, and use the
rotational button ( a ) to roll up the strand from the ends
to the roots.
2 Keep the brush at the hair roots until the hair is
completely dry.
3 Remove the brush from the hair by using the opposite
rotation direction. To avoid tangles, remember to move
the brush away from your hair as you do so.
4 To style the rest of your hair, repeat steps 1-3.
• Style the hair tips (Fig. 5-C)
1 Insert the brush ( g ) at the hair tips.
2 Choose the rotation direction for the desired results
( inwards icks or outwards icks ).
3 Activate the rotation, allowing the brush to rotate at the
hair tips until the hair is completely dry and
properly shaped.
4 To style the rest of your hair, repeat steps 1-3.
• Straighten the hair (Fig.5-D)
1 Insert the brush under your hair at the roots.
2 Pull the brush down the length of the hair from the roots
to the ends, without using the rotation.
4 After use
Remarks: Only apply hair spray and other xation styling
products after styling.
1 Switch o the appliance and unplug it.
2 Place it on a heat-resistant surface until it cools down.
3 Clean the appliance and attachments by damp cloth.
4 Keep it in a safe and dry place, free of dust. You can also
hang it with the hanging loop ( f ).
5 Guarantee & service
If you need information e.g. about replacement of an
attachment or if you have a problem, please visit the Philips
website at www.philips.com.cn/support or contact the
Philips Customer Care Centre in your country (you will nd
its phone number in the worldwide guarantee leaet). If
there is no Consumer Care Centre in your country, go to your
local Philips dealer.
1
A
C
D
B
5
4
2
3
a
bc
d
h
i
j
e
f
g
产品中有害物质的名称及含量
部件名称
有害物质
铅
（
Pb
）
汞
（
Hg
）
镉
（
Cd
）
六价铬
（
Cr6+
）
多溴联苯
（
PBB
）
多溴二苯醚
（
PBDE
）
电源线
X
O O O O O
马达
X
O O O O O
本表格依据
SJ/T 11364
的规定编制。
O
：表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572
规定的限量要求以下。
X
：表示该有害物质至少在该部件的某一均质材料中的含量超出
GB/T 26572
规定的限量要求。
ϔ৮ 喟下ݖ⊓㒻ࣾ䕍ಸக
ಸत 喟)1
䷊Ⴧ⩢ࢸ 喟7_
䷊Ⴧ䶾⢴ 喟)[
䷊Ⴧ䓀ڒߌ⢴ 喟8
⩌ϔᬒ 喟䄤㻮ϔ৮᱙Ҁ
ϔౝ 喟͚పᎬ͉͉㣋
下ݖ⊓喍͚ప喎ែ䉱ᰶ䭽ڙथ
̷⊤ጯ๖Ⱋ㺬䌜त
ڕప䶫ߎ☚㏬喟
᱙ϔ৮ᵦᢛపᴴ(#
(#(#
ࣷ(#ݣ䕍
6 Troubleshooting
Problem Cause Solution
The
appliance
does not
work at all.
The power
socket to which
the appliance
has been
connected may
be broken.
Check the appliance is
plugged in correctly.
Check the fuse for this
power socket in
your home.
The appliance
may have
overheated and
switched
itself o.
Unplug the appliance
and let it cool down for a
few minutes. Before you
switch on the appliance
again, check the
attachment to make sure
they are not blocked by
u, hair, etc.
The appliance
may not be
suitable for the
voltage to which
it has been
connected.
Ensure that the voltage
indicated on the type
plate of the appliance
corresponds to the local
power voltage.
简体中文
感谢您的惠顾，欢迎光临飞利浦！为了
您能充分享受飞利浦提供的支持，请在
www.philips.com.cn/welcome 上注册您
的产品。
1 重要事项
使用产品之前，请仔细阅读本用户手册，
并妥善保管以供日后参考。
• 警告：请勿在靠近水的地方使用本
产品。
• 本产品在浴室内使用时，使用后拔
下插头，因为即使本产品开关断开
后，接近水仍存在危险。
• 警告：不要在盛水的浴缸、淋浴、
洗脸盆或其他器皿附近使用
本器具。
• 警告符号注释：禁止在洗澡
或淋浴时使用。
• 使用后务必拔下产品的插头。
• 如果产品过热，它将自动关闭
电源。拔掉产品插头，让其冷却几
分钟。再次启动产品之前，请检查
出风口，确保其未被绒毛、头发等
杂物堵塞。
• 如果电源线损坏，为避免危险，必
须由飞利浦、飞利浦授权的服务中
心或类似的专职人员来更换。
• 在有人指导如何安全使用本产品，
监督掌握安全使用方法的情况下，
本产品适合8岁或以上的儿童以及
肢体不健全、感觉或精神上有障碍
或缺乏相关经验和知识的人士使
用。但同时他们需要意识到相关的
危险。不得让儿童玩耍本产品。不
要让儿童在无人监督的情况下进行
清洁和保养。
• 为了增加保护，建议在浴室供电的
电气回路中安装一个额定剩余工作
电流不超过 30mA 的剩余电流装
置 (RCD)。详情请向 RCD 安装
商咨询。
• 连接产品之前，请确保产品上标示
的电压与当地电源电压相符。
• 请勿将本产品用于本手册中说明以
外的任何其它用途。
• 切勿阻塞出风口。
• 当产品连接了电源时，切勿让其无
人看管。
• 切勿使用由其它制造商生产的，或
未经飞利浦特别推荐的任何附件或
部件。如果使用此类附件或部件，
您的保修将失效。
• 切勿将电源线缠绕在产品上。
• 待产品完全冷却后再存放。
• 由于产品会很烫，请在使用时多
加注意。 只能握住手柄，因为其
他部位会很烫，并且避免与皮肤
接触。
• 不要使电源线接触到产品的灼热
部分。
• 请勿对假发使用本产品。
• 当产品变热时切勿在其表面覆盖任
何物品（如毛巾或衣服）。
• 切勿用湿手操作本产品。
• 保持金属棒洁净无尘且未粘上定型
产品（如摩丝、定型喷剂和
发胶）。
• 金属棒具有涂层。 此涂层可能会
随着时间的推移慢慢磨损。 但
是，这并不影响产品的性能。
• 将产品用于染过色的头发时，金属
棒可能会染上颜色。
• 产品只能送到飞利浦授权的服务中
心检修。 由不合格人员进行修理
可能将用户置于极度危险的境地。
• 切勿将金属物体插入开口中，以免
触电。
• 使用后请勿拉扯电源线。拔下产品
插头时，请握紧插头。
电磁场(EMF)
本飞利浦产品符合所有有关暴露于电磁场
的适用标准和法规。
环境
弃置产品时，请不要将其与一般生活
垃圾堆放在一起；应将其交给官方指
定的回收中心。这样做有利于环保。
2 造型前
注意：在连接或拆开附件之前，请务必先
让产品及其附件冷却。
备注：因头发湿度而异，每缕头发的造型
时间可能有差异。若头发比建议的湿度
更大，则造型需要更长的时间。
1 选择您所需的配件 ( d, g, h )
并将其固定在美发造型器的 ( e )
手柄上。
• 当配件冷却后，按下释放按钮( b )
可取下配件。
2 将插头连接至电源插座。
3 将风速开关 ( c ) 滑动至强劲暖风
可快速吹干；暖风 可柔和干发与定
型，防止头发过热；冷风 可为您的
秀发定型。
3 如何造型
尝试使用本产品两至三次，就可熟悉操作
方式。
(A)集风嘴配件(h)
1 选择集风嘴 ( h ) 并将其固定于手柄
上 ( e )。
2 （图 5-A ) 选择合适的设置吹干
头发 ( c )。
(B)空气卷发配件(d)
提示和诀窍：
如需获取详细的使用说明，请参阅随附的
快速入门指南。
• （图 2）卷发配件可从不同角度固定
在手柄上。为了方便您的使用，您可以
根据自己手持产品的习惯来调整位置
• 使用产品之前，请预先吹干头发（包括
发根）。为获得最佳的效果，头发应处
于 80%–90% 的干燥状态
• 彻底梳理头发，并确保没有缠结
• 将头发分成几撮。将无需造型的头发放
置于远离开口的位置
• 从后脑处开始卷发
• 选择强劲暖风设置 开启产品。
（图 3） 在放入头发前，检查开口处
是否有堵塞。按下旋转按钮前确保没有
杂物堵塞开口
• 将所选发缕绕卷几圈，可更轻松将其放
入开口
• 将开口对着要开始卷发处的位置放置。
请勿放置在过于靠近发根的位置
• 将头发放入开口时，拉紧发缕
• 头发完全卷入时，请勿立即松开旋转
按钮。请继续旋转 10 秒钟，以便确
保头发完全进入卷发仓内
• 检查发缕末端是否已进入卷发仓。确保
没有多余散落的头发
• （图 4）如有头发被夹住，请关闭产
品。 轻轻地将夹住的头发分撮慢慢拉
出，直到松开所有的头发。或者，在关
闭产品的情况下按住空气卷发配件的侧
面按钮 ( i )，取下配件顶盖并松开
夹住的头发
(C)发梳配件(g)
• 打造波浪卷发/增强头发丰盈度
( Fig.5-B )
1 将发梳 ( g ) 放置在发梢，并使用旋
转按钮 ( a )，将发缕从末端卷向
发根。
2 让发梳停留在发根位置，直到头发完全
变干。
3 为防止缠结，请务必将发梳朝远离头发
的方向使用反向旋转的方式，将发梳从
头发上取下。
4 要为其余头发造型，请重复
步骤 1-3。
• 为发梢造型（图5-C）
1 将发梳 ( g ) 插入发梢。
2 为所需效果（内卷或外翻卷发）选择旋
转方向。
3 启动旋转，可让发梳在发梢处旋转，直
至头发完全变干并适当定型。
4 要为其余头发造型，请重复
步骤 1-3。
• 拉直头发（图5-D）
1 将发梳插入发根位置。
2 将发梳从发根一直向下拉至发梢，无需
使用旋转。
4 使用后
备注：造型后，仅能使用头发定型剂和其
他固定造型产品。
1 关闭产品并拔下电源插头。
2 将产品置于隔热表面上，直至其冷却。
3 用湿布清洁本产品和附件。
4 将产品存放在安全、干燥、清洁的
位置。您也可以使用挂环 ( f ) 将产
品挂起存放。
5 保修与服务
如果您需要了解信息（如更换附件的相关
信息）或有任何疑问，请访问飞利浦网站
www.philips.com.cn/support。您也可以
与您所在国家/地区的飞利浦客户服务中
心联系（可从保修卡中找到其电话号
码）。如果您所在的国家/地区没有飞利
浦客户服务中心，请向当地的飞利浦经销
商求助。
6 故障排除
问题 原因 解决方法
产品完
全无法
工作。
产品所连
接的电源
插座可能
已损坏。
检查设备已正确插
入。
检查您家中电源插座
的保险丝。
产品可能
过热，
因此自动
断电。
拔掉产品插头，让其
冷却几分钟。 再次
打开产品电源之前，
请检查附件出风口，
确保没有被绒毛、头
发等杂物堵塞。
产品连接
的电源电
压可能与
产品电压
不符。
确保产品型号铭牌上
标示的电压与当地电
源电压相符。
保留备用
出版日期：2017-04-06
-
1
-
2
