XBA-C10iP
Stereo Headphones
Operating Instructions
使用說明書
4-456-227-12(1)
Removing the headphones
After use, remove the headphones slowly.
Note
Headphones are designed to fit closely in your ears. If
the headphones are pressed hard while in use or taken
off too quickly, they may cause injury.
Wearing headphones may produce a diaphragm click
sound. This is not a malfunction.
Precautions
High volume may affect your hearing.
For traffic safety, do not use while
driving or cycling.
Install the earbuds firmly. If an earbud
accidentally detaches and is left in your
ear, it may cause injury.
Keep earbuds clean. To clean the
earbuds, wash them with a mild
detergent solution.
Compatible iPod/iPhone/iPad models
You can use the unit with only the following models
supporting remote control. Update your iPod, iPhone
or iPad to the latest software before use. In the
Operating Instructions, iPod, iPhone and iPad are
collectively described as “iPod” except in special cases.
iPod touch (5th generation)
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod nano (7th generation)
iPod nano (6th generation)
iPod nano (5th generation)
iPod nano (4th generation)
iPod classic 120GB 160GB (2009)
iPod shuffle (4th generation)
iPod shuffle (3rd generation)
iPhone 5
iPhone 4S
iPhone 4
iPhone 3GS
iPad (4th generation)
iPad (3rd generation)
iPad 2
iPad
iPad mini
English Stereo headphones
Using the Centre button
Plays/pauses a track of the connected iPod product
with a single press. Skips to the next track with a
double press. Skips to the previous track with a triple
press. Starts the “VoiceOver*” feature with a long press
(if available).
Press once to answer the call. Press again to end. Hold
down for about two seconds to reject an incoming
call. When you let go, two low beeps confirm the call
was rejected.
* Availability of the “VoiceOver” feature depends on
iPod and its software version.
Note
Be careful not to unintentionally press any buttons
when you carry your iPod with this unit connected.
How to use / 使用方法 /
Earbuds / 耳塞 /
SS S M L
©2012 Sony Corporation
Printed in Thailand
Specifications
Headphones
Type: Closed, Balanced Armature
Driver unit: Balanced Armature
Power handling capacity: 100 mW (IEC*)
Impedance: 24 at 1 kHz
Sensitivity: 106 dB**
Frequency response: 5 Hz – 25,000 Hz
Cord: 1.2 m (Y-type)
Plug: Four-conductor gold-plated L-shaped stereo
mini plug for iPod/iPhone/iPad with remote function
Mass: Approx. 4 g (without cord)
Microphone
Open circuit voltage level: – 42 dB (0 dB=1 V/Pa)
Supplied accessories
Earbuds: SS (red) (2), S (orange) (2), M (green)
(attached to the unit at the factory) (2), L (light blue)
(2) / Cord adjuster (winds cord up to 50 cm) (1) / Clip
(1)
* IEC = International Electrotechnical Commission
** 150 mV input
Design and specifications are subject to change
without notice.
Optional replacement earbuds can be ordered from
your nearest Sony dealer.
Note on static electricity
Static electricity accumulated in the body may cause
mild tingling in your ears.
To minimise the effect, wear clothes made from natural
materials.
Volume +*
音量 +*
Centre button
中央按鈕
Volume
音量 -
Microphone
⿆克⾵
* There is a tactile dot beside Volume +.
*
音量 + 旁有一個觸覺點。
On copyright
iPad, iPhone, iPod, iPod classic, iPod nano, iPod shuffle,
and iPod touch are trademarks of Apple Inc., registered
in the U.S. and other countries.
“Made for iPod,” “Made for iPhone,” and “Made for iPad”
mean that an electronic accessory has been designed
to connect specifically to iPod, iPhone or iPad,
respectively, and has been certified by the developer
to meet Apple performance standards. Apple is not
responsible for the operation of this device or its
compliance with safety and regulatory standards.
Clip / 線夾 /