3
8
STCD1080
STDC001L
13
18
23
INDONESIA
29
34
繁體中文
2
A
C
B
D
E
3
ENGLISH
(Original instructions)
Intended use
Your Stanley drill/screwdriver has been designed for
screwdriving applications and for drilling in wood, metal and
plastics.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
Technical data
STDC001L/STCD1080
Voltage V
DC
10.8
No-load speed /min
0-315, 0-1200
Max. torque
(PTI Rating)
Nm 27
Chuck capacity mm 10
Max Drilling capacity
Steel/wood mm 10/25
Weight kg 1.1
Charger
Input Voltage
V
AC
220-240
Output
Output Curren(DC)
Voltage V
DC
10.8
A 2
Approx. charge time min
30
Battery
Voltage
V
DC
10.8
Capacity Ah 1.5
Type Li-Ion
STDC001L /STCD1080
10.8V LI-ION DRILL
4
ENGLISH
(Original instructions)
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a.
manufacturer. A charger that is suitable for one type of
another battery pack.
b.
battery packs. Use of any other battery packs may create
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for drills
and impact drills
u Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
u Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
u Hold power tool by insulated gripping surfaces when
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
5
ENGLISH
(Original instructions)
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
p
Do not attempt to charge damaged batteries.
Chargers
u Use your Stanley charger only to charge the battery in
the tool with which it was supplied. Other batteries could
burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Chuck
4. Torque adjustment collar
5. Battery
6. Belt clip
7. LED work light
8. Speed selector
9. Magnetic bit holder
Fig. A
10. Charger
11. Charging indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
6
ENGLISH
(Original instructions)
u To remove the battery, push the release buttons (12) while
at the same time pulling the battery out of the receptacle.
Fitting and removing a drill bit or screwdriver bit
exchange of bits.
u Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u Grasp the chuck (3) and rotate it in the counterclockwise
direction, as viewed from the chuck end.
u Insert the bit shaft (13) into the chuck.
u Firmly tighten the chuck by rotating it in the clockwise
direction as viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other ac-
cessory) by gripping the front part of the chuck and turning the
tool on. Damage to the chuck and personal injury may occur
when changing accessories in this manner.
Use
Warning! Let the tool work at its own pace. Do not overload.
-
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u To charge the battery (5), insert it into the charger (10).
not force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
(slowly).
The charge is complete when the charging indicator (11)
lights green continuously. The charger and the battery can be
occasionally tops up the battery charge. The charging indica-
tor (11) will be lit as long as the battery is connected to the
plugged-in charger.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
follows:
u Re-insert the battery (5).
u
rate, use a different battery to determine if the charging
process works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
service centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(2) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
u To lock the tool, set the forward/reverse slider into the
centre position.
Selecting the torque
screwdriving and drilling applications. Large screws and hard
workpiece materials require a higher torque setting than small
symbol refer to the listing below.
u For drilling in wood, metal and plastics, set the torque
adjustment collar (4) to the
b
symbol.
u For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
- Set the torque adjustment collar (4) to the lowest torque
setting.
-
- If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
7
ENGLISH
(Original instructions)
Speed selector
u For drilling in steel and for screwdriving applications, slide
the speed selector (8) towards the rear of the tool (1st
gear).
u For drilling in materials other than steel, slide the speed
selector (8) towards the front of the tool (2nd gear).
Drilling/screwdriving
u Select forward or reverse rotation using the forward/re-
verse slider (2).
u To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
u To switch the tool off, release the switch.
LED work light
The LED work light (7) is activated automatically when the trig-
ger is depressed. The LED work light will illuminate when the
trigger is partially depressed, before the unit begins running.
Hints for optimum use
Drilling
u Always apply a light pressure in a straight line with the drill
bit.
u Just before the drill tip breaks through the other side of the
workpiece, decrease pressure on the tool.
u Use a block of wood to back up workpieces that may
splinter.
u Use spade bits when drilling large diameter holes in wood.
u Use HSS drill bits when drilling in metal.
u Use masonry bits when drilling in soft masonry.
u Use a lubricant when drilling metals other than cast iron
and brass.
u Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
u Always use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
u Always hold the tool and screwdriver bit in a straight line
with the screw.
Maintenance
Your Stanley tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
replacement, or if it is of no further use to you, do not dispose
Should you find one day that your Stanley product needs
of it with household waste. Make this product available for
separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Batteries
Z
Run the battery down completely, then remove it
from the tool.
u NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
8
简体中文
技术参数
STCD1080
充电器
电池
10.8
STCD1080
10.8伏特 锂电池电源电钻
电压
空载速度
最大扭矩
（PTI额定）
夹头尺寸
最大钻孔性能
钢材/木材
重量
输入电压
输出电压
输出电流 （直流）
充满电大约时间
电压
容量
类型 Li-ion
伏（直流）
转/分
牛米
毫米
毫米
千克
伏（交流）
伏（直流）
安培
分钟
伏（直流）
安培小时 1.5
220
10.8
2
30
10.8
0-315, 0-1200
27
10
10/25
1.1
设计用途
本史丹利电钻/起子机的设计用途是拧螺丝，以及在
木材、金属、和塑料材料上钻孔。
请妥善保管所有警示与须知，以备将来参考使用。
在所有以下列举的警告中术语“电动工具”指用电
驱动（有线）电动工具或电池驱动（无线）电动工
具。
安全须知
电动工具安全通则
警告！阅读说明。没有按照以下列举的说
明而使用或操作将导致触电、着火和/或
严重伤害。
电气安全
电动工具插头必须与插座相配。不能以任何方式
改装插头。需接地的电动工具不能使用任何转换
插头。未经改装的插头和相配的插座将减少触电
危险。
避免人体接触接地表面，如管道、散热片和冰箱。
如果你身体接地会增加触电危险。
不得将电动工具暴露在雨中或潮湿环境中。水进
入电动工具将增加触电危险。
不得滥用电线。绝不能用电线搬运、拉动电动工
具或拔出其插头。让电动工具远离热、油、锐
边或运动部件。受损或缠绕的电线会增加触电危
险。
当在户外使用电动工具时，使用适合户外使用的
外接电线。适合户外使用的电线将减少触电危险。
如果在潮湿的环境中使用电动工具，请使用漏电
保护装置（RCD）。使用此装置可降低触电危险。
2.
a.
b.
工作场地
保持工作场地清洁和明亮。混乱和黑暗的场地会
引发事故。
不要在易爆环境，如有易燃液体、气体或粉尘的
环境下操作电动工具。电动工具产生的火花会点
燃粉尘或气体。
让儿童和旁观者离开后操纵电动工具。分心会使
你放松控制。
1.
a.
b.
c.
c.
d.
e.
f.
人身安全
保持警觉，当操作电动工具时关注所从事的操作
并保持清醒。切勿在有疲倦、药物、酒精或治疗
反应下操作电动工具。在操作电动工具期间精力
分散会导致严重人身伤害。
使用安全装置。始终配戴护目镜。安全装置，
诸如适当条件下的防尘面具、防滑安全鞋、安全
帽、听力防护等装置能减少人身伤害。
避免突然起动。确保开关在插入插头时处于关断
位置。手指放在已接通电源的开关上或开关处于
接通时插入头可能会导致危险。
在电动工具接通之前，拿掉所有调节钥匙或扳手。
遗留在电动工具旋转零件上的扳手或钥匙会导致
人身伤害。
手不要伸得太长。时刻注意脚下和身体平衡。
这样在意外情况下能很好地控制电动工具。
着装适当。不要穿宽松衣服或佩带饰品。让你的
头发、衣服和袖子远离运动部件。宽松衣服、佩
饰或长发可能会卷入运动部件。
如果提供了与排屑装置、集尘设备连接用的装置，
则确保他们连接完好且使用得当。使用这些装置
可减少碎屑引起的危险。
3.
a.
b.
c.
d.
e.
f.
g.
9
简体中文
电动工具使用和注意事项
不要滥用电动工具，根据用途使用适当的电动工
具。选用适当的设计额值的电动工具会使你工作
有效、更安全。
如果开关不能接通或关断工具电源，则不能使用
该电动工具。不能用开关来控制的电动工具是危
险的且必须进行修理。
4.
a.
b.
c.
c.
d.
e.
d.
e.
f.
g.
在进行任何调节、更换附件或贮存电动工具之前，
必须从电源上拔掉插头和／或将电池盒脱开电源。
这种防护性措施将减少电动工具突然起动的危险。
将闲置电动工具贮存在儿童所及范围之外，并且
不要让不熟悉电动工具或对这些说明不了解的人
操作电动工具。电动工具在未经训练的用户手中
是危险的。
保养电动工具。检查运动部件的安装偏差或卡住、
零件破损情况和影响电动工具运行的其它条件。
如有损坏，电动工具必须在使用前修理好。许多
事故由维护不良的电动工具引发。
保持切削刀具锋利和清洁。保养良好的有锋利切
削刃的刀具不易卡住而且容易控制。
按照使用说明书以及打算使用的电动工具的特殊
类型要求的方式，考虑作业条件和进行的作业来
使用电动工具、附件和工具的刀头等。电动工具
用作那些与要求不符的操作可能会导致危险情况。
5.
6.
a.
a.
b.
维修
让专业维修人员使用特定备件维修电动工具。这
这将保证所维修的电动工具安全。
使用冲击钻时，请佩戴听力保护器。暴露在噪音
中会损伤听力。
请使用随工具提供的辅助手柄。工具失控会导致
人身伤害。
工具配件可能接触隐藏的导线时，请仅握持绝缘
的把手表面。如果配件接触“带电”的导线，工
具暴露金属部件的表面会“带电”，并且导致操
作员触电。
紧固件可能接触隐藏的导线时，请仅握持绝缘的
把手表面。如果紧固件接触“带电”导线，工具
暴露金属部件的表面会“带电”，并且导致操作
员触电。
请使用夹钳或其它切实可行的方法来固定和支撑
工件，将其固定到稳定的工作台上。用手抓住工
字钢件或用身体抵住工件并不稳定，可能会导致
工件失控。
钻进墙壁，地板或天花板之前，请首先检查导线
和管道的位置。
刚刚钻完时，避免接触钻头，因为钻头可能很烫。
除非其安全负责人进行工具使用的监督或指导，
否则体力，感知能力或心智不足的人（包括儿童），
以及缺乏经验与相关知识的人不得使用本工具。
必须看管儿童，勿使其拿本工具玩耍。
本指导手册已经说明了预定用途，如果配件或附
件的使用，本工具的操作超出本指导手册建议的
范围，则可能出现人身伤害和/或财产损坏风险。
除非其安全负责人进行工具使用的监督或指导，
否则体力、感知能力或心智不足的人（包括儿
童）不得使用本工具。
必须看管儿童，勿使其拿本工具玩耍。
电动工具的附加安全守则
注意！请遵守电钻和冲击钻的附加安全守
则。
他人安全
残余风险
使用工具时，可能出现本安全警示之外的其它残余
风险。这些风险可能来自使用不当、使用时间过长
等。
尽管实行了相关的安全法规、采用安全装置，某些
残余风险是不可避免的，这包括：
电池式工具使用和注意事项
确保开关在插入电池盒前处于断开状态。将电池
盒插入到开关状态为接通的电动工具上会引发事故。
只用制造商规定的充电器充电。将适用于某种电
池盒的充电器用到其他电池盒时会发生着火危险。
只使用配有特制电池盒的电动工具。使用其他电
池盒会发生损坏和着火危险。
当电池盒不用时，将它远离其他金属物体，例如
回形针、硬币、钥匙、钉子、螺钉或其他小金属
物体，以防一端与另一端连接。电池端部短路会
引起燃烧或者火灾。
在滥用条件下，液体会从电池中溅出；避免接触。
如果无意间碰到了，用水冲洗。如果液体碰到了
眼睛，还要寻求医疗帮助。从电池中溅出的液体
会发生腐蚀或燃烧。
10
简体中文
接触旋转/移动部件时的伤害风险。
更换部件、刃具或配件时的伤害风险。
长期使用时的伤害风险。长期使用任何工具时，
均应定期休息。
听力损伤。
吸入工具使用过程中產生的粉尘后，导致健康
风险（例如：使用木材，特别是橡木、山毛榉
和中密度纤维板时）。
禁止以任何理由试图打开电池。
禁止与水接触。
禁止存放在温度可能超过40℃的地点。
仅在10到40℃的环境温度范围内充电。
仅使用随工具配备的充电器。
丢弃电池时，请遵守“保护环境”章节中的规定。
本史丹利充电器仅限于随电器/工具提供的电池充
电。如用于其它电池，会导致电池爆炸，造成人
身伤害与损坏。
严禁给非充电电池充电。
有问题的电源线应立即更换。
禁止暴露在水中。
请勿打开充电器。
请勿使用探针等查探充电器。
禁止给损坏的电池充电。
本充电座仅限室内使用。
使用工具前，请仔细阅读使用手册。
警告！为降低伤害风险，使用前务必阅读
使用手册。
工具上的标志
本工具上有如下图形标志：
电池组和充电器安全附则
充电器
电池
电气安全
部件名称
本工具包含以下部分或全部部件：
1. 调速开关
2. 正转/倒转拨杆
3. 工具夹头
4. 扭力调节环
5. 电池
6. 皮带夹
7. LED工作指示灯
8. 速度选择开关
9. 磁性夹头
组装
警告！组装之前，请把电池从工具上取下。
电池安装与拆卸步骤（图C）
钻头或起子头的安装与拆卸步骤（图D）
本工具配有无键夹头，便于更换工具头。
图A
10. 充电器
11. 充电指示灯
本工具采用双重绝缘；因此不需要地线。
请务必检查电源是否与铭牌上的电压一致。
禁止使用普通插头代替充电器单元。
如果电源线损坏，必须由厂商或史丹利授权服务
中心更换，以排除隐患。
要安装电池（5），将其对准工具上的电池插槽。
然后，滑动电池进入插槽，向里推直至电池咬合
到位。
要取下电池，按下释放按钮（12），同时把电池
从插槽中拉出。
把正转/倒转拨杆（2）设定到中心位置，即可锁
定工具。
握住夹头（3）并逆时针旋转（从夹头端看）。
把工具头柄（13）插入夹头。
把夹头顺时针拧紧（从夹头端看）。
11
简体中文
注意：确定电池是否失效需要的时间可能长达60分
钟。如果电池过热或过冷，LED灯会快、慢交替闪
红光，快、慢闪光各闪一次，如此往复。
选择旋转方向（图E）
当钻孔和紧固螺丝时，采用正转（顺时针）。松开
螺丝或撤出卡住的钻头时，使用反转（逆时针）。
力矩的选择
本工具配有扭力调节环，可以满足各种锁螺丝和钻
孔需要。对于大螺丝和硬材质工件，其力矩要求比
小螺丝和软材质工件要高。各符号的定义如下：
速度选择开关
钻孔/锁螺丝
如果另一电池可以正常充电，则表明原电池失效，
应送交维修中心回收。
如果另一电池遇到原电池同样的问题，请把充电
器送往授权维修中心检测。
要选择正转，把正转/反转拨杆（2）推向左边。
要选择反转，把正转/反转拨杆推向右边。
要锁定工具，把正转/反转拨杆置于中间位置。
在木材、金属及塑料上钻孔时，请把力矩调节环
（4）设定到 图标。
锁螺丝时，把调节环设定到所需档位。如果您不
清楚正确设定，请按如下步骤操作：
在钢材上钻孔，或锁螺丝时，请把速度选择开关
（8）滑动到工具后部（1档）。
在非钢材材料上钻孔时，请把速度选择开关（8）
滑动到工具前部（2档）。
使用正转/倒转拨杆（2）选择正转或倒转。
要启动工具，请按下开关（1）。工具速度取决于
您按下开关的程度。
要关闭工具，松开开关即可。
警告！禁止通过握住夹头前部并启动工具来紧固钻头
（或任何其它配件）。这会损坏夹头并导致人身伤害。
使用步骤
警告！让电动工具在自有节奏下工作，请勿过载。
给电池充电（图A）
电池在首次使用前须充电；一旦不能产生充足电力
来完成此前轻易完成的工作，亦需充电。充电过程
中，电池会变热；这是正常现象，并非故障。
警告！请勿在环境温度低于10℃或大于40℃时给电
池充电。建议充电温度为大约24℃。
注意：当电池温度低于大约10°C或高于40°C时，充
电器不能给电池充电。此时，应把电池留在充电器
中。当电池温度回暖或冷却下来后，充电器会自动
开始充电。
充电指示灯（11）会连续闪烁绿光（慢速）。
充电指示灯（11）连续发绿光时，表明充电已经完
成。充电器和电池可以无限期连接在一起，同时LED
亮。充电器偶然给电池加满电时，LED会转变为绿色
闪光（充电）状态。只要电池与插好插头的充电器
保持连接，充电指示灯（11）就会发光。
把电池留在充电器中
充电器和电池组可以保持无期限连接，此时LED发光；
充电器会保持电池充电并充满。
充电器故障诊断
如果充电器检测到电池已经老化或损坏，充电指示
灯（11）会快速闪烁红光。此时，请按如下步骤操
作：
要给电池（5）充电，将其插入充电器（10）中。
电池只能以一种方式插入充电器。切勿强行插入。
请确保电池与充电器完全配合到位。
插上充电器插头并打开电源开关。
电池放电后1个星期内应充电。如果存放放电后的
电池，电池寿命会大大缩短。
重新插入电池（5）。
如果充电指示灯继续快速闪烁红光，请使用另一
块电池来确定充电过程是否正常。
请把扭力调节环（4）设定到最小档。
锁固第一颗螺丝。
如果在达到所需结果前，离合器松开, 请增
加调节环的设定, 继续锁螺丝,. 重复本步骤
直到达到正确设定, 并使用该设定来锁其余
的螺丝。
-
-
-
12
简体中文
LED工作指示灯
当触发开关被按下时，LED工作指示灯（7）会自动
启动。当触发开关被部分按下时，在工具开始旋转
之前，LED工作指示灯亮。
最佳操作提示
钻孔
锁螺丝
维护
本史丹利电动工具设计精良，可以长期运作，而只需
极少的维护。要取得连续的令人满意的工作效果，需
要您做合适的保养和定期的清洁。
除了定期清洁外，本充电器无须其它维护。
警告！维护工具前，必须从工具上取下电池；清洁充
电器前，请拔下插头。
保护环境
u
u
u
u
u
u
u
u
u
u
u
u
u
u
始终保持轻度压力，与钻头成一直线。
在钻头即将透过工件另一侧时，降低对工具施加
的压力。
如果工件可能碎裂，应衬以木块。
在木块上钻大直径孔时，应使用铲形钻头。
在金属上钻孔时，应使用HSS钻头。
在软砖上钻孔时, 应使用砖石钻头。
在除铸铁或黄铜之外的金属上钻孔时，应使用润
滑剂。
使用中心冲头冲出孔的中心点，以提高准确性。
请始终使用正确类型和尺寸的起子头。
如果螺丝难于紧固，可使用少量的洗涤液或肥皂
做润滑剂。
请始终保持工具和起子头与螺丝在同一直线上。
定期使用软刷或干布清洁工具的通风槽。
定期使用湿布清洁马达外壳，但不得使用任何研
磨性或溶剂型清洁剂。
定期打开并轻拍夹头，清除内部灰尘。
个别收集用过的产品和包装允许材料再循
环利用。重新使用循环利用的材料有助于
防止环境污染，并减少原始材料的需求。
把电池组电力完全耗尽，然后从工具上取
下。
当您购买新产品时，可能提供从家用、城市垃圾站
通过零售商个别收集电气产品的当地法规。
如果您发现您的史丹利产品需要进行替换，或您已经
不再需要使用这些产品，请不要将它们与家庭废物一
起处理。务必将本产品送往个别收集处。
电池组
个别收集。本产品必须与一般家庭废物分
开处理。
u
镍镉和镍氢电池是可以回收的。把它们送往经
销商或者本地的回收站。
制造厂：史丹利百得精密制造（深圳）有限公司
地 址：广东省深圳市宝安区石岩街道水田社区
捷和工业城
1.5
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
