Philips WP3861/00 ユーザーマニュアル

カテゴリー
ウォーターディスペンサー
タイプ
ユーザーマニュアル
Register your product and get support at
www.philips.com/welcome
WP3861
1
WP3861 Philips Pure Taste
ENGLISH 6
繁體中文 17
简体中文 26
6
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers,
register your product at www.philips.com/welcome.
You have made an excellent choice. The Philips Pure Taste is a compact and
easy-to-install water purier that improves the taste of your drinking and
cooking water by removing chlorine and other impurities with a silver-
coated activated carbon lter. Better-tasting water made easy, by Philips.
General description (Fig. 1)
A Non-woven cloth
B Silver-coated granular activated carbon
C Filter cartridge
D Cap of lter cartridge holder
E Viewing window
F Filter cartridge holder
G Water selection lever
H Water purier housing
I Stainless steel screen
J Rubber washer
K Adapter
1 A-type
2 B-type
3 C type
4 D-type
L Attachment nut
Important
Read this user manual carefully before you use the water purier and
save it for future reference.
Warning
- This water purier is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given
ENGLISH
supervision or instruction concerning use of the water purier by a
person responsible for their safety.
- Children should be supervised to ensure that they do not play with
the water purier.
Before daily use
- To prevent quick clogging of the lter cartridge, let the water run at
the unltered setting for around 5 seconds before every use.
- If the water is highly coloured or turbid due to work on your water
network, do not let the water run at the ltered setting until the
water is clear.
- Cautions:
1 Let the water run at the ltered setting for 10 seconds before use
each day.
2 Let the water run at the ltered setting for 60 seconds before use if
you have not used the water purier for more than two days.
3 If you are not going to use the water purier for more than two
weeks, put the lter cartridge in the refrigerator to ensure its good
performance. When you start using the water purier again, let
the water run at the ltered setting for 1 minute before use. If the
lter cartridge emits an unpleasant smell, replace it with a new one.
Water temperature
- Do not let water hotter than 50°C run through the water purier at
the unltered setting or hotter than 35°C at the ltered setting.
This may damage the water purier.
- Do not let the water purier freeze.
Applications
- Only use the water purier to lter water that meets drinking water
standards.
- Do not use this water purier in combination with electric taps.
- Do not block the ltered water outlet or connect other devices to it.
- If the water pressure is very high, reduce the water ow of the tap to
prevent damage to the cartridge.
ENGLISH 7
- Keep the water purier away from heat to avoid distortion or
breakage.
- Do not tamper with the water purier.
- Do not remove the lter cartridge while you use the water purier.
- Do not install the water purier near a window where it is exposed
to direct sunlight.
- Do not use the water purier without a lter cartridge.
- This water purier does not soften water.
- Do not use ltered water in aquariums. Tap water, ltered or
unltered, can be harmful to sh.
- This water purier is intended for household use only.
- Do not store puried water to avoid contamination. Air contact
contaminates puried water quickly. If you want to store puried
water, use a clean container and keep it in the refrigerator. Do not
keep it in the refrigerator longer than 1 day to avoid contamination.
Features
- The water purier removes chlorine, unpleasant smells and tastes, as
well as large sediments from your tap water.
- The silver-coated activated carbon prevents bacteria growth inside
the lter.
- The replacement reminder sticker helps you remember when to
replace the lter cartridge.
- The 2ltrs/min high-speed initial ow rate gives you plenty of clean
water instantly.
- The water selection lever offers you a choice of three water ow
types: unltered spray, unltered stream or ltered spray.
- The eight tap-mounting adapters supplied with the water purier
allow easy installation on almost any type of tap.
- The bayonet-type mount ensures quick, easy and secure lter
cartridge replacement.
ENGLISH8
Preparing for use
Before installation
- Before you install the water purier, make sure all tap-mounting
adapters you require are present.
- The tap must have a diameter of 13mm-25mm.
- Determine what type of tap you have and select the appropriate
adapter.
- The adapters supplied make the water purier suitable for almost
any kitchen tap. However, the water purier may not t some
uncommon types of taps.
- The tap water pressure has to be between 0.7kgf/cm² (7 metres of
water column/70kPa) and 3.5kgf/cm² (35 metres of water column/
350kPa). If you use the water purier at a water pressure outside this
range, either the ltered water ow will be extremely low or the
water purier will get damaged.
Installation A-type adapter
- For taps with a round spout with a diameter of 16mm, 17.5mm or
19mm (Fig. 2).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 3).
2 Pass the attachment nut over the tap spout (Fig. 4).
3 Place the matching adapter (A-type) over the tip of the spout. The
16mm adapter is packed with the water purier. Replace it with
the 17.5mm adapter or 19mm adapter to t the diameter of your
tap (Fig. 5).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 6).
Installation B-type adapter
- For taps with an aerator (threaded outside) (Fig. 7).
1 Remove the attachment nut and the adapter from the water
purier (Fig. 8).
ENGLISH 9
2 Remove the aerator cap from the tap and pass the attachment nut
over the spout. Take out the original adapter and screw the
matching adapter (B-type) onto the tap (Fig. 9).
3 Tighten the adapter further with a coin (Fig. 10).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 11).
Installation C-type adapter
- For taps with an aerator (threaded inside) (Fig. 12).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 13).
2 Remove the aerator cap from the tap. Take out the original adapter
and screw the matching adapter (C-type) onto the tap through the
attachment nut. (Fig. 14)
If water leakage occurs, wind Teon tape round the adapter’s thread
before you screw it onto the tap.
3 Tighten the adapter further with a coin (Fig. 15).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 16).
Installation D-type adapter
- For taps other than A, B or C. (Fig. 17)
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 18).
2 Take out the original adapter and screw the D-type adapter loosely
onto the water purier housing. (Fig. 19)
3 Push the water purier housing onto the tap from below and
tighten the 4 screws evenly (Fig. 20).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 21).
Make sure the rubber washer is rmly pushed against the tap to prevent
water leakage.
ENGLISH10
Installing the lter cartridge
1 Make sure the tap is closed.
2 Set the water selection lever to the unltered stream
position (Fig. 22).
3 Tilt the lter cartridge holder 90° backwards and insert it into the
water purier housing (Fig. 23).
4 Pull the cartridge holder upwards until it is in upright
position. (Fig. 24)
Using the water purier
1 Make sure that the water purier housing and the lter cartridge
holder are properly installed.
2 Turn the water selection lever to the desired setting (‘click’).
Filtered spray
Select this setting for drinking, washing vegetables or fruits and
for cooking.
Tip: We advise you to boil the ltered water before you drink it.
1 Turn the water selection lever until the ltered spray symbol is
aligned with the indicator (Fig. 25).
Do not let water hotter than 35°C run through the water purier at
this setting, as this may damage the water purier.
If you lter water between 35°C and 50°C, the water may have an
unpleasant smell. The lter cartridge has absorbed this smell during
ltering, but releases it again if you lter water hotter than 35°C.
ENGLISH 11
Unltered spray
Select this setting for washing dishes and other jobs that require a gentle
water ow.
1 Turn the water selection lever until the unltered spray symbol is
aligned with the indicator (Fig. 26).
Do not let water hotter than 50°C run through the water purier at
this setting, as this may damage the water purier.
Unltered stream
Select this setting for a strong water ow.
1 Turn the water selection lever until the unltered stream symbol is
aligned with the indicator (Fig. 22).
Do not let water hotter than 50°C run through the water purier at
this setting as this may damage the water purier.
Cleaning
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the water purier. These substances
may cause cracking, discolouration or distortion.
1 Clean the water purier housing and the inside and outside of the
lter cartridge holder and cap regularly with a damp cloth.
Replacement
New lter cartridges are available under type number WP3961.
Replace the lter cartridge if it is clogged to prevent damage to the
water purier.
ENGLISH12
1 For optimal performance of the water purier, replace the lter
cartridge if either of the following situations occurs:
A You have used the lter cartridge for six months.
B The non-woven cloth of the lter cartridge has turned rust brown or
dark grey.
Look through the viewing window in the cap of the lter cartridge holder
to see the colour of the non-woven cloth.
C The volume of puried water decreases substantially.
D The ltered water still has an unpleasant smell after purication.
2 To replace the lter cartridge, close the tap and set the water
selection lever to the unltered stream position. (Fig. 22)
3 Tilt the lter cartridge holder 90° backwards and pull it off the
water purier housing. (Fig. 27)
4 Unscrew the cap of the lter cartridge holder (Fig. 28).
When you remove the cap of the lter cartridge holder, water leaks
from the water inlet of the holder.
5 Remove the lter cartridge from the holder. (Fig. 29)
6 Put a new lter cartridge in the holder (Fig. 30).
7 Screw the cap back onto the lter cartridge holder (Fig. 31).
8 Tilt the lter cartridge holder 90° backwards and insert it into the
water purier housing (Fig. 23).
9 Pull the cartridge holder upwards until it is in upright
position. (Fig. 24)
10 Write down the date on which you have to replace the lter
cartridge on the replacement reminder sticker.
Note: The lter cartridge holder and the cap can be purchased as service parts.
ENGLISH 13
Replacement reminder sticker
- We advise you to replace the lter cartridge every 6 months,
for optimum performance. Please register your product online at
http://www.philips.com/welcome for more information on lter
cartridge replacement.
Note: The actual lifetime of the lter cartridge strongly depends on the
quality of the local tap water.
- The water purier and each replacement lter cartridge comes with
a replacement reminder sticker. Write the date on which you have to
replace the lter cartridge on the sticker and stick it on the outside of
the cap. This helps you remember when to replace the lter
cartridge. (Fig. 32)
Guarantee and service
If you need service or information or if you have a problem, please visit
the Philips website at www.philips.com or contact the Philips Consumer
Care Centre in your country (you nd its phone number in the
worldwide guarantee leaet). If there is no Consumer Care Centre in
your country, go to your local Philips dealer.
Frequently asked questions
This chapter lists the questions most frequently asked about the water
purier. If you cannot nd the answer to your question, contact the
Consumer Care Centre in your country.
ENGLISH14
Question Answer
Why does water
leak from
the attachment nut?
Perhaps you have not installed the water
purier properly. Reinstall the water purier
according to the instructions in this user manual.
Perhaps the attachment nut or the tap-
mounting adapter is damaged. Contact an
authorised Philips service centre.
Perhaps the tap water pressure is higher than
specied.
You may need to wind some Teon tape around
the thread of the adapter.
Why is the water
ow weak at
the unltered
setting?
Perhaps the stainless steel screen under the
rubber washer inside the water purier housing
is clogged. Clean it with a toothbrush and rinse it.
Why is the water
ow is weak at the
ltered setting?
Perhaps the lter cartridge is clogged.
Replace the lter cartridge.
Perhaps the tap water pressure is lower
than specied.
ENGLISH 15
Product specications
Product name and
type number
WP3861 Philips Pure Taste
Type Direct tap mount
Major lter
components
Granular activated carbon
Initial water ow rate 2ltrs/min. (water pressure at 1kgf/cm²
(10 metres of water column/ 100kPa),
water temperature at 20°C)
Filter lifetime Approximately 6 months at 10ltrs a day
(the actual lifetime depends on the quality of
the local water and the water pressure)
Replacement lter
cartridge
WP3961
Minimum water
pressure
0.7kgf/cm² (7 metres of water column/70kPa)
Maximum water
pressure
3.5kgf/cm² (35 metres of water
column/350kPa)
Accessories WP3961 lter cartridge, 8 tap-mounting
adapters, replacement reminder sticker
Water purier
dimensions
105mm x 139mm x 83mm (H x W x D)
Packaging dimensions 140mm x 170mm x 84mm (H x W x D)
Weight Approximately 370g
Country of origin Japan
*Above specications are according to Japanese JIS S 3201 Standard.
ENGLISH16
17
簡介
恭喜您購買本產品並歡迎加入飛利浦!請於
www.philips.com/welcome 註冊您的產品,
以善用飛利浦提供的支援。
您的選擇是完美的。飛利浦 Pure Taste 是造型輕巧、
安裝容易的淨水器,鍍銀微粒活性炭濾芯能去除氯氣和其他雜質,
為您帶來口感更佳的飲用與煮食用水。
一般說明 (圖 1)
A 不織布
B 鍍銀微粒活性炭
C 濾芯
D 濾芯固定座保護蓋
E 檢視窗
F 濾芯固定座
G 選水調整鈕
H 淨水器外殼
I 不鏽鋼網
J 橡膠墊圈
K 轉換器
1 A 型
2 B 型
3 C 型
4 D 型
L 連接螺帽
重要事項
使用淨水器前,請先仔細閱讀使用手冊,並保留說明以供日後參考。
警示
- 本淨水器不適合供下列人士 (包括小孩) 使用:身體官能或心智
能力退化者,或缺乏經驗與使用知識者。他們需要人員在旁指
導或說明淨水器的使用方法,以確保安全。
- 請看管孩童,避免他們將淨水器當成玩具。
繁體中文
每日使用前
- 為防止濾芯快速阻塞,每回使用之前,請先在未過濾的設定下
讓水流出約 5 秒時間。
- 若水管由於施工而造成水的顏色很深或者混濁,請先等待水清
澈之後,再開始設定過濾水源。
- 警告:
1 每日使用之前,請先讓水從過濾的設定下流出 10 秒。
2 淨水器若有兩天以上不曾使用,請先讓水從過濾的設定下流出
60 秒。
3 淨水器若超過兩週都不會使用,請將濾芯放入冰箱中保存,以
確保日後過濾品質。當您重新使用淨水器時,請先讓水從過濾
的設定下流出 1 分鐘之後再使用。如果濾芯發出異味,請更換
新濾芯。
水溫
- 若在未過濾設定下,請勿讓超過 50°C 的熱水通過淨水器,而
若在過濾設定下,則勿注入超過 35°C 的熱水,否則可能會損
壞淨水器。
- 請勿讓淨水器結冰。
使用方法
- 本淨水器限於用來過濾符合飲用水標準的水。
- 此淨水器請勿與電動水龍頭一起使用。
- 請勿堵住過濾水出水口,或連接其它裝置。
- 如果水壓非常高,請減少水龍頭的水流量,以免損壞濾芯。
- 淨水器請保持遠離熱源,以免變形或損壞。
- 請勿改裝淨水器。
- 使用淨水器時請勿取出濾芯。
- 請勿將淨水器安裝在窗戶附近,使其直接曝曬在陽光下。
- 尚未安裝濾芯前,請勿使用淨水器。
- 本淨水器無法軟化水質。
- 請勿將過濾後的水用於水族箱。自來水無論過濾與否,對魚類
都可能有害。
- 本淨水器僅供家用。
- 請勿儲存濾淨後的水,以免水質遭受污染。空氣的接觸會快速
污染濾淨後的水,若您想儲存濾淨後的水,請使用乾淨的容器
繁體中文18
然後將其放入冰箱內。在冰箱中,請勿放置超過 1 天以上,
以免遭受污染。
功能
- 淨水器可去除氯、不好的氣味或異味,以及自來水中的大量沈
積物。
- 鍍銀活性炭可預防濾芯滋生細菌。
- 濾芯更換貼紙可幫助您記得何時應更換濾芯。
- 每分鐘 2 公升的高速初期流速,立即給您充沛的淨水。
- 選水調整鈕提供三種水流選擇:未過濾噴水、未過濾水流或已
過濾噴水。
- 淨水器隨附八種安裝於水龍頭使用的轉接頭,幾乎所有類型的
水龍頭都可輕鬆安裝。
- 採取卡栓型的安裝方式,能確保更換濾芯的過程快速、簡易並
且牢固。
使用前準備
安裝之前
- 在您安裝本淨水器之前,請先確定安裝於水龍頭所需的轉接頭
都已備齊。
- 水龍頭的直徑必須為 13 - 25 公釐。
- 請判斷您的水龍頭屬於哪種類型,再選取適當的轉接頭。
- 隨附的轉接頭讓本淨水器幾乎適用於所有廚房水龍頭。然而,
本淨水器可能無法適合某些少見類型的水龍頭。
- 自來水水壓必須在 0.7kgf/cm² (7 公尺水柱/70kPa) 到 3.5kgf/
cm² (35 公尺水柱/350kPa) 之間。若您以此範圍以外的水壓使
用本淨水器,則過濾後的水流可能極小,或者淨水器會受損。
安裝 A 型轉接頭
- 適合直徑為 16 公釐、17.5 公釐或 19 公釐的圓口水龍
頭。 (圖 2)
1 將連接螺帽與轉接頭從淨水器外殼取下。(圖3)
2 將連接螺帽穿過水龍頭的口。(圖4)
繁體中文 19
3在水龍頭的口端放置相符的轉接頭(A型)。16公釐轉接頭與淨
水器一同包裝。請依照水龍頭的直徑,更換為適合的17.5公
釐轉接頭或19公釐轉接頭。(圖5)
4將連接螺帽牢固地鎖在淨水器外殼上。(圖6)
安裝 B 型轉接頭
- 適合裝有濾水網罩的水龍頭 (螺紋在外)。 (圖 7)
1 將連接螺帽與轉接頭從淨水器取下。(圖8)
2 將濾水網罩的外蓋從水龍頭取下,再將連接螺帽穿過水龍頭的
口。取出原有的轉接頭,將相符的轉接頭(B型)鎖到水龍頭
上。(圖9)
3用硬幣將轉接頭鎖得更緊。(圖10)
4將連接螺帽牢固地鎖在淨水器外殼上。(圖11)
安裝 C 型轉接頭
- 適合裝有濾水網罩的水龍頭 (螺紋在內)。 (圖 12)
1 將連接螺帽與轉接頭從淨水器外殼取下。(圖13)
2 將濾水網罩的外蓋從水龍頭取下。取出原有的轉接頭,利用連
接螺帽將相符的轉接頭(C型)鎖到水龍頭上。(圖14)
如果發生漏水現象,請在轉接頭的螺紋四周纏繞鐵弗龍膠帶,再
鎖到水龍頭上。
3用硬幣將轉接頭鎖得更緊。(圖15)
4將連接螺帽牢固地鎖在淨水器外殼上。(圖16)
安裝 D 型轉接頭
- 適合 A、B 或 C 型以外的水龍頭。 (圖 17)
1 將連接螺帽與轉接頭從淨水器外殼取下。(圖18)
2 取下原有的轉接頭,將D型轉接頭稍微鎖在淨水器外殼
上。(圖19)
3將淨水器外殼從下方推到水龍頭上,再將4枚螺絲釘平均地鎖
緊。(圖20)
繁體中文20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Philips WP3861/00 ユーザーマニュアル

カテゴリー
ウォーターディスペンサー
タイプ
ユーザーマニュアル

他の言語で