產品示意圖與配件表
MR2-B31
A
B
C
D
E
F
G
H
I
J
燈號說明
C
B
A
銳銨科技
硬體安裝
RAID 模式切換設定
產品使用注意事項
銳銨科技股份有限公司
www.STARDOM.com.tw
[email protected]
銳銨科技股份有限公司
STARDOM銳銨科技股份有限公司
切換RAID設定的標準程序：
E
D
F
H
I
J
G
V1.0 (Feb. 2020)
RAID 1 RAID 0, BIG, JBOD
N/A
- ( N/A N/A
- N/A N/A
MR2-B31 Quick Setup Guide
Product Illustration and Parts List
The Indication of HDD Status
Please follow the instructions below to complete the hardware installation.
Hardware Installation
Place the system on a stable surface. Ensure that the vent is not blocked and that it is
installed in a well-ventilated area. (Please keep the product away from moisture and
other environment that might be harmful to the product)
1.
2.
3.
4.
5.
6.
7.
Please check the product and accessories for any defect or missing parts. If you have any
questions, please contact your product supplier.
Please visit the official website - Download page (http://www.stardom.com.tw/STAR-
DOM2016/download.php) to download other related resources.
The following items should be inside the package upon opening:
A
B
C
D
E
F
G
H
I
J
C
B
A
Use the ejector pin included in the
accessory kit to eject the HDD enclosure
handle, and then pull tray handle to
remove it.
Mount the 2.5" HDD onto the removable
tray.
When the HDD installation has been completed, insert the tray into the system
horizontally and secure the latch into place.
Use the RAID switch on the back of MR2-B31 to set the RAID mode to be used.
Please connect the signal cable first, and then power cord later.
After completing hardware installation, turn on the power and follow the instruction of
Disk Utility to format the two HDDs, you then could start using your new MR2-B31.
RAID Mode Setting:
Provide a big storage capacity and the data transfer efficiency, but no data porotection
feature.
Because of this Mirroring feature, your two HDDs/SSDs will keep an identical data
after your wtiting works. In case one of the two HDDs/SSDs is defect, MR2-B31+
would still work fine with only one of them. And once inserting a good HDD/SSD
as the defect replacement, it will do the rebuilding work by itself.
With JBOD mode, you could actually use the two HDDs/SSDs as the normal two
storages for your large memory capacity requirement, but no data porotection
feature.
You could enjoy a double memory capacity from this BIG feature, but no data
porotection feature.
RAID 0
RAID 1
JBOD
BIG
The Standard Procedure to Switch RAID Setting:
1.
2.
3.
4.
5.
6.
Please first connect MR2-B31 to your computer.
When the blue light of the HDD access light is always on, please set RAID switch to
JBOD.
Please use the key to press the RESET hole, wait for the Blue-Purple LED on the HDD
access light to finish blinking, and turn it into a solid blue light, then release the key.
When the blue light of the HDD access light is always on, please set RAID switch to the
position you demand.
Please use the key to press the RESET hole, wait for the Blue-Purple LED on the HDD
access light to finish blinking, and turn it into a solid blue light, then release the key.
Please turn off your MR2-B31, and turn it back on again. You now have reset MR2-B31
with a new RAID mode successfully.
Important Notice
STARDOM is one brand under RAIDON TECHNOLOGY, INC.
Thank you for choosing STARDOM’s product.
The information provided in this manual was checked before publication, but the actual product
specifications may have changed before shipping; Latest product specifications and updates can be
found at www.STARDOM.com.tw or through your sales representative. No separate notifications will be
provided by our company.
If you have any questions about RAIDON products or would like to receive the latest product
information, instruction manuals, or firmware, please contact [email protected] for assistance.
All product-related content in this manual are copyrighted by RAIDON TECHNOLOGY, INC.
Stardom Storage Solutions
Product Parts List
RAID 1
RAID 0
BIG
JBOD
(default)
NOTE:
Please make sure that the product is connected to the host (power on status) before turning
on the power, otherwise the product will be on the sleep mode.
After the hard disk is formatted, the actual total capacity of the MR2-B31 detected by the
computer operating system will vary from the sum of all hard disk capacities stated by the
manufacturer.
To prevent data loss, do not remove MR2-B31 while the system is running.
Please always connect the USB cable to the computer to ensure the energy saving
function operating normally.
Once the system has been initialized, do not switch hard disks around during use. Doing
so may prevent the RAID from being recognized by the system.
Once RAID mode has been set up, the switching of hard drives will lead to the removal of
data from the hard disks. Please be sure to backup the data on the hard disk before
making any switches.
Before switching the RAID mode, you need to switch to JBOD before adjusting to the
required mode.
The product needs to be restarted after adding or changing the RAID mode, and the
update is guaranteed to be the new RAID mode.
If the MR2-B31+ needs to be shut down or disconnected, please ensure the HDD is
safely removed through your operating system before turning off the power.
We strongly recommend backing up important data stored on the MR2-B31 to another
storage device or a remote site. STARDOM will not be held liable for the damage or loss
of data you stored on the MR2-B31.
1.
2.
3.
4.
5.
6.
7.
8.
9.
V1.0 (Feb. 2020)
Status
HDD Status Light
RAID 1 RAID 0, BIG JBOD
HDD idle Blue light always on Blue light always on Blue light always on
No HDD detected Red light always on Red light always on Red light always on
Data access
HDD failure N/A
Rebuilding data -
Source HDD
Breathing Blue Light N/A N/A
Rebuilding data -
Target HDD
Breathing Purple Light N/A N/A
E
D
F
H
I
J
G
-
1
-
2
