Philips RQ320/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル
ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Make sure the adapter does not get
wet (Fig. 1).
- The adapter contains a transformer.
Do not cut off the adapter to replace
it with another plug, as this causes a
hazardous situation.
Warning
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with the
appliance.
- Be careful with hot water when you
clean the appliance. Always check if the
water is not too hot, to prevent your
hands from getting burnt.
Caution
- Charge, use and store the shaver at a
temperature between 5°C and 35°C.
- Always put the protection cap on the
shaver to protect the shaving heads
when you are travelling.
- The shaver and the accessories are not
dishwasher-proof.
- Never use water hotter than 80°C to
rinse the shaver.
- Only use the adapter supplied.
- Do not use the shaver or the adapter if
it is damaged.
- If the adapter is damaged, always have
it replaced with one of the original type
in order to avoid a hazard.
- Water may leak from the socket at the
bottom of the shaver when you rinse
it. This is normal and not dangerous
because all electronics are enclosed in
a sealed power unit inside the shaver.
Compliance with standards
- This shaver complies with the
internationally approved safety
regulations and can be safely cleaned
under the tap (Fig. 2).
- This Philips appliance complies with all
standards regarding electromagnetic
elds (EMF). If handled properly
and according to the instructions in this
user manual, the appliance is safe to use
based on scientic evidence available
today.
General
- The adapter transforms 100-240 volts
to a safe low voltage of less than 24
volts.
General description (Fig. 3)
1 Protection cap
2 Shaving unit with shaving head holder
3 Shaving head holder release buttons
4 On/off slide
5 Retaining ring
6 Cutter
7 Shaving guard
8 Shaving head holder
9 Cleaning brush
10 Adapter
11 Charging light
12 Small plug
Charging
It takes approx. 10 hours to fully charge the
battery.
A fully charged shaver provides up to 20
shaving minutes.
If you have a heavy beard, the shaver may
provide less than 20 shaving minutes. The
number of shaving minutes may also vary
over time, depending on your shaving
behaviour, cleaning habits and beard type.
’Charging’ indication
- When the shaver is charging, the light
on the adapter lights up (Fig. 4).
RQ320, RQ310
Register your product and get support at
www.philips.com/welcome
4222.002.5425.1
3
1
2 4
5
6
7
8 9
10
11
12 13
14
15 16
17
18
19
20 21
22
23
24 25
26
Charging
Do not charge the shaver in the packaging.
1 Switch off the shaver.
2 Put the small plug in the shaver.
3 Put the adapter in the wall socket.
, The light on the adapter lights up to
show that the shaver is charging.
Note: The light on the adapter does not
change colour and does not go out when the
shaver is fully charged.
Using the shaver
Note: You can use this shaver while it is
connected to the mains. However, it does not
operate from the mains when the battery is
empty. In this case, rst charge the shaver for
at least 1 hour.
Shaving
Skin adaptation period
Your rst shaves may not bring you the
result you expect and your skin may even
become slightly irritated. This is normal. Your
skin and beard need time to adapt to any
new shaving system.
We advise you to shave regularly (at least
3 times a week) for a period of 3 weeks to
allow your skin to adapt to the new shaver.
During this period, use your new electric
shaver exclusively and do not use other
shaving methods. If you use different shaving
methods, it is more difcult for your skin to
adapt to the new shaving system.
1 Move the on/off slide upwards to
switch on the shaver.
2 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 5).
3 Move the on/off slide downwards to
switch off the shaver.
4 Clean the shaver after every
shave (see chapter ‘Cleaning and
maintenance’).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol
or acetone to clean the shaver and its
accessories.
- Clean the shaver after every shave.
- Clean the shaving heads frequently
with Philips Shaving Head Cleaning
Spray (HQ110) for optimal shaving
performance.
- You can clean the outside of the
shaver with a damp cloth. Do not clean
the shaving unit with a cloth.
Cleaning the shaving unit
Be careful with hot water. Always check if
the water is not too hot, to prevent your
hands from getting burnt.
1 Switch off the shaver.
2 Rinse the shaving unit under a hot tap
for some time (Fig. 6).
Note: You can also clean the shaving unit with
the cleaning brush supplied.
3 After rinsing the appliance under the
tap, hold it upright for 10-15 seconds
to allow water to run out of the
bottom.
4 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit
(2). (Fig. 7)
5 Rinse the shaving head holder under a
hot tap for 30 seconds (Fig. 8).
Note: You can also clean the shaving head
holder with the cleaning brush supplied.
6 Carefully shake off excess water and
let the shaving head holder dry.
Never dry the shaving head holder with
a towel or tissue, as this may damage the
shaving heads.
7 Reattach the shaving head holder
to the shaving unit (‘click’) (Fig. 9).
Extra-thorough cleaning method
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit
(2) (Fig. 10).
3 To unlock the orange retaining ring,
turn it in the direction of the arrows
indicated in and on the retaining
ring (Fig. 11).
4 Lift the retaining ring out of the
shaving head holder. (Fig. 12)
5 Remove the cutter and the shaving
guard (Fig. 13).
Note: Do not clean more than one cutter
and shaving guard at a time, since they are
all matching sets. If you accidentally put a
cutter in the wrong shaving guard, it may
take several weeks before optimal shaving
performance is restored.
6 Clean the cutter with the cleaning
brush supplied (Fig. 14).
7 Clean the inside of the shaving
guard (Fig. 15).
8 After cleaning, place the shaving guard
back into the shaving head holder.
Make sure the two wings t exactly
into the recesses of the shaving head
holder (Fig. 16).
9 Place the cutter back into the shaving
guard with the cutter legs pointing
downwards (Fig. 17).
10 Place the retaining ring back onto the
shaving head holder (1). To reattach
the retaining ring, turn it against the
direction of the arrows indicated in
and on the retaining ring (2) (Fig. 18).
Note: Make sure the retaining ring is xed
properly. The four wings of the retaining ring
have to be located exactly under the recesses
of the shaving head holder (Fig. 19).
11 Reattach the shaving head holder to
the shaving unit (‘click’). (Fig. 9)
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Storage
Note: Make sure the shaving unit is dry before
you store the shaver.
1 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 20).
Replacement
For maximum shaving performance, we
advise you to replace the shaving heads
every two years. Replace damaged shaving
heads right away.
Only replace the shaving heads with original
RQ32 Philips shaving heads. See also
chapter ‘Ordering accessories’.
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit and pull the shaving head
holder off the shaving unit (Fig. 7).
3 To unlock the orange retaining ring,
turn it in the direction of the arrows
indicated in and on the retaining
ring (Fig. 11).
4 Lift the retaining ring out of the
shaving head holder (Fig. 12).
5 Remove the shaving heads and place
new ones in the shaving head holder.
Make sure the two wings of the shaving
heads t exactly into the recesses.
6 Place the retaining ring back onto the
shaving head holder (1). To reattach
the retaining ring, turn it against the
direction of the arrows indicated in
and on the retaining ring (2) (Fig. 18).
Note: Make sure the retaining ring is xed
properly. The four wings of the retaining ring
have to be located exactly under the recesses
of the shaving head holder (Fig. 19).
7 Reattach the shaving head holder to
the shaving unit (‘click’) (Fig. 9).
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Ordering accessories
To purchase accessories for this
appliance, please visit our online shop at
www.shop.philips.com/service. If the
online shop is not available in your country,
go to your Philips dealer or a Philips service
centre. If you have any difculties obtaining
accessories for your appliance, please
contact the Philips Consumer Care Centre
in your country. You nd its contact details
in the worldwide guarantee leaet.
The following accessories are available:
- RQ32 Philips shaving heads
- HQ110 Philips Shaving Head Cleaning
Spray
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 21).
- The built-in rechargeable shaver battery
contains substances that may pollute
the environment. Always remove the
battery before you discard or hand in
the shaver at an ofcial collection point.
Dispose of the battery at an ofcial
collection point for batteries. If you
have trouble removing the battery, you
can also take the appliance to a Philips
service centre. The staff of this centre
will remove the battery for you and will
dispose of it in an environmentally safe
way (Fig. 22).
Removing the rechargeable
shaver battery
Only remove the rechargeable battery
when you discard the shaver. Make sure
the rechargeable battery is completely
empty when you remove it.
Be careful, the battery strips are sharp.
1 Undo the screw in the back panel of
the shaver with a screwdriver (1) and
remove the back panel (2) (Fig. 23).
2 Bend the hooks aside and remove the
power unit (Fig. 24).
3 Break the snap hooks (1) and remove
the front panel of the power unit
(2) (Fig. 25).
4 Take out the battery holder (1) and
cut the battery tags with a pair of
cutting pliers (2) (Fig. 26).
5 Remove the rechargeable battery.
Problem Possible
cause
Solution
The rota-
tion speed
of the
shaving
heads is
lower than
usual.
Too much
dirt has
collected
in the
shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The re-
chargeable
battery is
low.
Recharge
the battery.
See chapter
‘Charging’.
The
shaving
heads do
not stay in
place.
You did
not x the
retain-
ing rings
properly.
The retaining
ring is xed
properly
if the four
wings of the
retaining ring
are located
exactly under
the recesses
of the shaving
head holder.
After fully
charging
the shaver,
it provides
less than
20 shaving
minutes.
If you have
a heavy
beard, the
shaver may
provide
less than
20 shaving
minutes.
The
number
of shaving
minutes
may also
vary over
time,
depending
on your
shaving
behaviour,
cleaning
habits
and beard
type.
Guarantee and service
If you need service or information or if
you have a problem, please visit the Philips
website at www.philips.com/support or
contact the Philips Consumer Care Centre
in your country. You nd its phone number
in the worldwide guarantee leaet. If there
is no Consumer Care Centre in your
country, go to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact the
Consumer Care Centre in your country.
Problem Possible
cause
Solution
The shaver
does not
shave as
well as it
used to.
The
shaving
heads are
damaged
or worn.
Replace the
shaving heads
(see chapter
‘Replace-
ment’).
The shav-
ing heads
are dirty.
Clean the
cutters and
guards with
the cleaning
brush supplied
(see chapter
‘Cleaning and
maintenance’,
section ‘Extra-
thorough
cleaning
method’).
Problem Possible
cause
Solution
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the cleaning
brush supplied
(see chapter
‘Cleaning and
maintenance’,
section ‘Extra-
thorough
cleaning
method’).
The shaver
does not
work
when I
switch it
on.
The re-
chargeable
battery is
empty.
Switch off
the shaver
and recharge
the battery
(see chapter
‘Charging’).
The
tempera-
ture of the
shaver is
too high. In
this case,
the shaver
does not
work.
Let the shaver
cool down. As
soon as the
temperature
of the shaver
has dropped
sufciently, you
can switch
on the shaver
again.
The shaver
does not
work, even
though it is
connected
to the
mains.
The re-
chargeable
battery is
empty.
Switch off
the shaver
and recharge
the battery
(see chapter
‘Charging’).
My skin is
irritated
after shav-
ing.
Your skin
needs time
to get
used to
the Philips
shaving
system.
Skin irritation
during the
rst 2-3
weeks of use
is possible.
After this
period, the
skin irritation
usually disap-
pears.
The
shaving
heads are
damaged
or worn.
Replace the
shaving heads
(see chapter
‘Replace-
ment’).
一般
- 轉換器可將 100-240 伏特的電壓轉
換為低於 24 伏特的安全低電壓。
一般說明 (圖 3)
1 保護蓋
2 附電鬍刀刀頭固定座的電鬍刀組
3 電鬍刀刀頭固定座釋放鈕
4 On/Off 開關
5 固定環
6 刀具
7 電鬍刀刀網
8 電鬍刀刀頭固定座
9 清潔刷
10 轉換器
11 充電指示燈
12 小插頭
充電
產品充飽電約需要 10 小時。
充飽電的電鬍刀可刮鬍 20 分鐘。
若您的鬢鬚濃密,電鬍刀的刮鬍時間可
能少於 20 分鐘。此外,取決於您的刮
鬍方式、清潔習慣和鬍鬚類型,可使用
時間也可能會隨著時日改變。
「充電」指示
- 電鬍刀充電時,轉換器的指示燈會
亮起。 (圖 4)
充電
請勿將電鬍刀置於包裝內充電。
1 請先關閉電鬍刀電源。
2 將小插頭插上電鬍刀。
3 將轉換器插入插座。
, 轉換器的指示燈亮起時,表示電鬍
刀正在充電中。
注意:電鬍刀充飽電力後,轉換器指示
燈不會變色,也不會熄滅。
使用本電鬍刀
注意:您可在本電鬍刀連接電源的情
況下使用電鬍刀。然而,當電池沒電
時,連接電源將無法操作電鬍刀。在此
情況下,第一次為電鬍刀充電至少需要
1小時。
刮鬍
皮膚適應期
您第一次刮鬍的結果可能不如您所預
期,皮膚甚至可能稍微刺痛。這是正常
現象。您的皮膚與鬍鬚需要時間適應任
何新的刮鬍系統。
繁體中文
簡介
感謝您購買本產品並歡迎加入飛利浦!
請於 www.philips.com/welcome 註冊
您的產品,以善用飛利浦提供的支援。
重要事項
在使用本產品前,請先仔細閱讀本使用
手冊,並保留使用手冊以供日後參考。
危險
- 請確定轉換器沒有弄濕。 (圖 1)
- 轉換器內含一個變壓器。請勿切斷
轉換器而以其他插頭取代,否則會
造成危險。
警示
- 基於安全考慮,在缺乏監督及適當
指示之下,本產品不適用於孩童及
任何身體、知覺、或心理功能障礙
者,或缺乏使用經驗及知識者。
- 請勿讓孩童使用本產品或將本產品
當成玩具。
- 清潔產品時,請小心使用熱水。請
隨時檢查熱水是否太燙,以避免手
部燙傷。
警告
- 請於 5°C 到 35°C 間充電、使用
並存放電鬍刀。
- 當您出外旅行時,請隨時為電鬍刀
加上保護蓋,以保護電鬍刀刀頭。
- 電鬍刀和配件均不可放入洗碗機
清洗。
- 切勿使用超過 80°C 的熱水沖洗
電鬍刀。
- 只能使用產品所附的變壓器。
- 電鬍刀或變壓器損壞時,請勿使
用。
- 如果轉換器損壞,請務必使用原型
號的轉換器進行更換,以免發生
危險。
- 在您沖洗時,水可能會從電鬍刀底
部的插孔流出。此為正常現象,不
會造成危險,因為所有的電子零件
都密封於電鬍刀內的電源裝置中。
符合標準
- 電鬍刀符合國際公認的安全規範,
可以直接在水龍頭之下以自來水安
全清洗。 (圖 2)
- 本飛利浦產品符合電磁波
(Electromagnetic fields,EMF) 所
有相關標準。只要使用方式正確並
依照本使用手冊之說明進行操作,
根據現有的科學研究資料,使用本
產品並無安全顧慮。
7 將電鬍刀刀頭固定座重新接上電鬍
刀組(會聽見「喀噠」一聲)。
(圖9)
超徹底清潔方法 
1 請先關閉電鬍刀電源。
2 按下電鬍刀組的釋放鈕(1)並將電
鬍刀刀頭固定座從電鬍刀組取下(2)
。(圖10)
3 若要鬆開橘色固定環,請將它依固
定環上指示的箭頭旋轉。(圖11)
4 從電鬍刀刀頭固定座上取出固定
環。(圖12)
5 取下電鬍刀刀網與刀片。(圖13)
注意:因為刀片及刀網是成對的一組,
請勿一次清潔一組以上。如果您不小心
將刀片放進錯誤的電鬍刀刀網中,可能
要花幾週的時間才能恢復最理想的刮
鬍效果。
6 使用隨附於電鬍刀的清潔刷來清潔
刀片。(圖14)
7 清潔電鬍刀刀網內部。(圖15)
8 清潔完畢後,將電鬍刀刀網裝回電
鬍刀刀頭固定座。請確定兩翼準確
崁入電鬍刀刀頭固定座的凹處。
(圖16)
9 請將刀片放回電鬍刀刀網,使刀片
腳朝下。(圖17)
10將固定環放回電鬍刀刀頭固定座(1)
。要重新裝回固定環,將固定環朝
箭頭標示的反方向旋轉(2)。
(圖18)
注意:請確定固定環已正確固定。固定
環的四翼必須準確崁入電鬍刀刀頭固定
座的凹處。(圖19)
11 將電鬍刀刀頭固定座重新接上電鬍
刀組(會聽見「喀噠」一聲)。
(圖9)
注意:若電鬍刀組無法順利關上,請檢
查電鬍刀頭安裝位置是否正確,以及固
定環是否確實固定。
收納 
注意:務必等電鬍刀組乾燥之後再收
納電鬍刀。
1 使用後請為電鬍刀蓋上保護蓋以防
損壞,並避免污垢累積在刀頭中。
(圖20)
我們建議您定期刮鬍 (每週至少 3 次) 為
期 3 週,讓您的肌膚適應新的電鬍刀。
這段期間,請只使用您的新電鬍刀,不
要使用其他的刮鬍方式。如果您使用不
同的刮鬍方式,您的皮膚可能較難適應
新的刮鬍系統。
1 將On/Off開關往上推,即可開啟電
鬍刀電源。
2 將電鬍刀頭在皮膚上移動,請同時
用直線及畫圓的方式來移動。
(圖5)
3 將On/Off開關往下推,即可關閉電
鬍刀電源。
4 每次刮鬍後,請清潔本電鬍刀(請
參閱「清潔與保養」單元)。
清潔與維護
切勿使用鋼絲絨、磨蝕性的清潔劑或侵
蝕性的液體(例如汽油或丙酮)清潔電鬍
刀及其配件。
- 每次刮鬍後均需清潔電鬍刀。
- 為得到最佳的刮鬍性能,請經常使
用飛利浦電鬍刀刀頭噴霧清潔劑
(HQ110) 清潔電鬍刀刀頭。
- 您可以使用濕布清潔電鬍刀外側。
請勿用布清潔電鬍刀組。
清洗電鬍刀組
請小心使用熱水。隨時檢查熱水是否太
燙,以避免手部燙傷。
1 請先關閉電鬍刀電源。
2 將電鬍刀組以熱水沖洗一段時間。
(圖6)
注意:您也可以用產品所附的清潔刷清
潔電鬍刀組。
3 在水龍頭下沖洗本產品,將其直立
10-15秒,讓水從底部流出。
4 按下電鬍刀組的釋放鈕(1)並將電
鬍刀刀頭固定座從電鬍刀組取下(2)
。(圖7)
5 將電鬍刀刀頭固定座放在熱水龍頭
下沖洗30秒。(圖8)
注意:您也可以用產品所附的清潔刷清
潔電鬍刀刀頭固定座。
6 仔細甩乾多餘的水份之後,讓電鬍
刀刀頭固定座乾燥。
切勿使用毛巾或紙巾擦乾電鬍刀刀頭固
定座,因為此舉可能會造成電鬍刀刀
頭損害。
問題 可能原因 解決方法
電鬍刀
不像平
常一樣
運作。
電鬍刀刀
頭毀壞或
磨損。
更換電鬍刀
刀頭 (請參閱
「更換」單
元)。
電鬍刀頭
髒污。
使用隨附的清
潔刷清潔刀具
及刀網 (請參
閱「清潔與維
護」單元的「
超徹底清潔方
法」小節)。
長鬍鬚卡
住電鬍刀
刀頭。
使用隨附的清
潔刷清潔刀具
及刀網 (請參
閱「清潔與維
護」單元的「
超徹底清潔方
法」小節)。
開啟產
品電源
時,電
鬍刀無
法使
用。
充電式電
池沒電。
關閉電鬍刀的
電源並為電
池充電 (請參
閱「充電」單
元)。
電鬍刀過
熱。在此
情況下,
電鬍刀將
無法使
用。
讓電鬍刀冷
卻。等到電鬍
刀充分降溫,
您就能再度啟
動電鬍刀的電
源。
電鬍刀
無法運
作,即
使已經
連接到
電源。
充電式電
池沒電。
關閉電鬍刀的
電源並為電
池充電 (請參
閱「充電」單
元)。
刮鬍之
後,皮
膚感到
刺痛。
您的皮膚
需要一些
時間才能
適應飛利
浦電鬍刀
系統。
開始使用的第
2 到 3 週,皮
膚可能會有過
敏現象。過了
這段時間,
皮膚過敏的症
狀通常會消
失。
電鬍刀刀
頭毀壞或
磨損。
更換電鬍刀
刀頭 (請參閱
「更換」單
元)。
- 本電鬍刀使用的充電電池可能含有
會污染環境的物質。將本電鬍刀丟
棄或是送到政府指定回收站前,請
務必先取出電池,並將電池送到政
府指定的電池回收站。若您無法取
出電池,也可將本產品帶到飛利浦
授權服務中心。服務中心會為您卸
下電池,並以對環境無害的方式處
理電池。 (圖 22)
取出電鬍刀的充電電池
棄置本電鬍刀前,請先取出充電電池。
當您要取出充電電池時,請確認其電力
已完全耗盡。
電池固定帶非常銳利,請小心。
1 用螺絲起子(1)轉開電鬍刀的背板
螺絲,拆下背板(2)。(圖23)
2 彎折旁邊的扣鉤,然後取出供電裝
置。(圖24)
3 斷開彈簧鉤(1),並取下供電裝置的
正面護板(2)。(圖25)
4 取出電池固定座(1)並使用剪鉗(2)
將電池拉片剪斷。(圖26)
5 取出充電電池。
保固與服務
若您需要相關服務或資訊,或是有任何
問題,請瀏覽飛利浦網站:
www.philips.com/support,或聯絡當
地的飛利浦客戶服務中心,您可以在全
球保證書上找到聯絡電話。若您當地沒
有客戶服務中心,請洽詢當地的飛利浦
經銷商。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損
性,因此不在全球保固範圍內。
故障排除
本章概述您使用本產品時最常遇到的問
題。如果您無法利用以下資訊解決您遇
到的問題,請造訪 www.philips.com/
support,或聯絡您所在國家/地區的飛
利浦客戶服務中心。
更換
為得到最佳的刮鬍性能,我們建議您請
每兩年更換一次電鬍刀刀頭。有損傷的
電鬍刀刀頭則請要立即更換。
更換電鬍刀刀頭時,限使用原廠 RQ32
飛利浦電鬍刀刀頭。亦請參閱「訂購配
件」單元。
1 請先關閉電鬍刀電源。
2 按下電鬍刀組的釋放鈕,將電鬍刀
刀頭固定座從電鬍刀組取下。
(圖7)
3 若要鬆開橘色固定環,請將它依固
定環上指示的箭頭旋轉。(圖11)
4 從電鬍刀刀頭固定座上取出固定
環。(圖12)
5 取出電鬍刀刀頭,然後在電鬍刀刀
頭固定座換上新的刀頭。
確定電鬍刀刀頭兩翼準確崁入凹處。
6 將固定環放回電鬍刀刀頭固定座(1)
。要重新裝回固定環,將固定環朝
箭頭標示的反方向旋轉(2)。
(圖18)
注意:請確定固定環已正確固定。固定
環的四翼必須準確崁入電鬍刀刀頭固定
座的凹處。(圖19)
7 將電鬍刀刀頭固定座重新接上電鬍
刀組(會聽見「喀噠」一聲)。
(圖9)
注意:若電鬍刀組無法順利關上,請檢
查電鬍刀頭安裝位置是否正確,以及固
定環是否確實固定。
訂購配件
如需購買本產品的配件,請造訪我們
的線上商店:www.shop.philips.com/
service。若您所在國家沒有線上商店,
請聯絡您的飛利浦經銷商或飛利浦服務
中心。如果無法取得產品的配件,請
聯絡您所在國家的飛利浦客戶服務中
心。如需詳細聯絡資料,請參閱全球
保證書。
備有下列配件可供另外選購:
- RQ32 飛利浦電鬍刀刀頭
- HQ110 飛利浦電鬍刀刀頭噴霧清
潔劑
環境保護
- 本產品使用壽命結束時請勿與一般
家庭廢棄物一併丟棄。請將該產品
放置於政府指定的回收站,此舉能
為環保盡一份心力。 (圖 21)
問題 可能原因 解決方法
刀頭的
旋轉速
度比平
常緩
慢。
過多污垢
累積在刀
頭中。
請清潔電鬍刀
刀頭。請參閱
「清潔與維
護」單元。
充電式電
池電力不
足。
為電池充電。
請參閱「充
電」單元。
電鬍刀
刀頭不
穩固。
固定環未
妥善固
定。
若固定環的四
翼已準確崁入
電鬍刀刀頭固
定座的凹處,
則表示固定
環已正確固
定。
電鬍刀
充飽電
後,可
提供的
刮鬍時
間少於
20 分
鐘。
若您的鬢
鬚濃密,
電鬍刀的
刮鬍時間
可能少
於 20 分
鐘。此
外,取決
於您的刮
鬍方式、
清潔習慣
和鬍鬚類
型,可使
用時間也
可能會隨
著時日改
變。
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Philips RQ320/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル

他の言語で