Tektronix K475 取扱説明書

Instructions

K475

Workstation Tower

070-8847-02

*P070884702*

070884702

www.tektronix.com

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

WARRANTY

Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and

workmanship for a period of one (1) year from the date of shipment. If a product proves defective during this

warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor,

or will provide a replacement in exchange for the defective product.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration

of the warranty period and make suitable arrangements for the performance of service. Customer shall be

responsible for packaging and shipping the defective product to the service center designated by Tektronix, with

shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a

location within the country in which the Tektronix service center is located. Customer shall be responsible for

paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage

resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;

b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been

modified or integrated with other products when the effect of such modification or integration increases the time

or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS

OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’

RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND

EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.

TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR

THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

K475 Workstation Tower Instructions i

Table of Contents

General Safety Summary ii...................................

Contacting Tektronix iii.............................................

Introduction 1..............................................

Base Assembly 5............................................

Drawer Shelf and Drawer 10...................................

Keyboard Shelf 14...........................................

Half Shelf 15................................................

Second Half Shelf 17..........................................

Leg Caps 18.................................................

Nylon Straps 19..............................................

Customization 20............................................

Specifications 21.............................................

Replaceable Parts 22..........................................

23...................................

ii K475 Workstation Tower Instructions

General Safety Summary

Observe these safety precautions when using the K475 Workstation Tower.

Keep the K475 Level

Keep the K475 level at all times, especially when it is loaded with instruments.

The tower is designed to be very stable, but it can fall over if tilted to extremes.

Observe this precaution especially in these cases:

HWhen rolling the tower across uneven floors.

HWhen rolling the tower through doorways with uneven thresholds.

HWhen lifting the tower wheels over cables.

HWhen rolling the tower up or down ramps.

Do Not Top-Load the K475

Do not load the top shelves of the K475 while leaving the bottom shelves empty.

That makes the tower top-heavy and easier to tip over. Load the top shelves only

if the bottom shelves are also loaded.

Do Not Overload Shelves

Do not put more weight on any tower shelf than is listed in the specifications.

Load the top of the tower evenly.

Observe Electrical Safety

All parts of the tower must be treated as electrical conductors, even if they

appear to be nonconducting. Do not rely on the casters to provide insulation

between the tower and the surface it stands on. Conversely, do not rely on the

casters to provide a conductive ground path for the tower.

Test the Stability of Custom Configurations

Changes in shelf location and loading can affect the balance of the tower. If you

arrange the shelves differently from the configuration described in this manual,

test the tower carefully for stability before using it.

K475 Workstation Tower Instructions iii

Preface

Contacting Tektronix

Phone 1-800-833-9200*

Address Tektronix, Inc.

Department or name (if known)

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

Web site www.tektronix.com

Sales support 1-800-833-9200, select option 1*

Service support 1-800-833-9200, select option 2*

Technical support Email: techsupport@tektronix.com

1-800-833-9200, select option 3*

6:00 a.m. -- 5:00 p.m. Pacific time

*This phone number is toll free in North America. After office hours, please leave a

voice mail message.

Outside North America, contact a Tektronix sales office or distributor; see the

Tektronix web site for a list of offices.

Preface

iv K475 Workstation Tower Instructions

K475 Workstation Tower Instructions 1

Introduction

The Tektronix K475 Workstation Tower requires some assembly. This manual

tells how to assemble and use the tower.

You can assemble the K475 Workstation Tower by yourself, but it is easier if you

have another person to help you.

You will need a large flat area to assemble the tower. The area should be level

and large enough to move the various parts into place. A carpeted floor space is

ideal.

Tools

You will need a 3/4 inch (19 mm) open-end wrench, or an adjustable wrench that

can be adjusted to that size.

Other tools are included with the K475 Workstation Tower. These include a

3/16 inch Allen wrench and a circular bubble level.

Parts Identification

The large pieces of the K475 Workstation Tower are packed separately in the

shipping carton. A bag of small parts is packed in a box with these instructions.

The included tools are also packed in this bag. Figure 1 on page 2 shows the

small parts you will be using.

Table 1 on page 3 lists all the parts needed to assemble the tower, including the

large pieces and assemblies. Take an inventory now to familiarize yourself with

the parts for the assembly process.

Introduction

2K475 Workstation Tower Instructions

1/4--20 Button Head

Screw, 1/2 inch length

1/2 inch Split Lockwasher

3/16 inch Allen Wrench

Short Rail

1/4 inch Tooth Lockwasher

Circular Bubble Level

Press-On

Probe Holder

Figure 1: Identification of Small Parts

Introduction

K475 Workstation Tower Instructions 3

Table 1: Parts List

Quantity Description

Large Parts

2Locking Casters

2Non-Locking Casters

2Half Shelves

1Drawer Shelf

1Drawer

1Keyboard Shelf

1Strut

2Leg assemblies

2Leg Caps

4Nylon Straps with buckles

Small Parts in Bag

41/2 inch Split Lockwashers

20 1/4--20 Cap Head Screws, 1/2 inch length

20 1/4 inch Tooth Lockwashers

20 Weld Nuts

1Press-On Probe Holder

Small Tools in Bag

13/16 inch Allen Wrench

1Circular Bubble Level

Introduction

4K475 Workstation Tower Instructions

Locking Caster

Non-Locking Caster

Strut

Leg Assembly

Leg Cap

Keyboard Shelf

Half Shelf

Front

Drawer Shelf

Drawer

Figure 2: The K475 Workstation Tower

K475 Workstation Tower Instructions 5

Base Assembly

Begin assembling the cart by joining the leg assemblies using the strut, and then

putting on the casters. You will use these parts:

H2 Locking Casters

H2Non-LockingCasters

H2 Extrusions

H2Legs

H4 Bumpons

H4 1/4--20 x 1-1/4 inch Screws

H4 1 inch Fender Washers

H13/16AllenWrench

H41x3inchEndCaps

H1Strut

H4 1/2 inch Split Lockwashers

H4 1/4--20 Button Head Screws, 1/2 inch length

H4 1/4 inch Tooth Lockwashers

H4 Short Rails

You will use a 3/4 inch (19 mm) wrench or adjustable wrench, and the 3/16 inch

Allen wrench included with your tower.

1. Prepare the strut as shown in Figure 3. Position the short rail with the raised

threaded flange toward the strut. Leave each screw assembly loose; do not

screw the short rail onto the button head screw more than one full turn.

Base Assembly

6K475 Workstation Tower Instructions

Front

Short Rail

1/4 inch Tooth Lockwasher

1/4--20 Button Head Screw

Figure 3: Preparing the Strut for Base Assembly

2. On each leg assembly, observe that there is a small, clear, plastic button on

the horizontal leg bar. This button is on the inside of the tower, at the back.

Position the leg assemblies as shown in Figure 4. Leave a space between the

leg assemblies about equal to the length of the strut.

Base Assembly

K475 Workstation Tower Instructions 7

Pencil Marks: first line should be 10 inches

from the bottom of the extrusion. For the first

leg assembly, turn extrusion so pencil marks

are on the inside. For second leg assembly,

pencil marks are also on the inside.

Bumpons are on the

inside of the extrusions.

Note: Leg tube can be crushed if screw is over

tightened; maximum torque is 3-6 foot/pounds.

Clear Plastic Buttons (1 on each leg assembly)

Figure 4: Aligning the Leg Assemblies and the Strut

3. Orient extrusion so the end with threaded holes is on the bottom If shelf

position pencil marks are present on one of the slotted sides of the extrusion

there should be one mark 10 inches from this end. You will build two leg

assemblies, one with the extrusion oriented with pencil marks on the right

side and the second with pencil marks on the left side.

4. Place extrusion on top of leg tube oriented so the caster nuts are on the

bottom as shown in Figure 4.

Base Assembly

8K475 Workstation Tower Instructions

5. Place long screw through washer and insert through bottom of leg tube (side

with large caster nuts) and into the extrusion. Screw will extend through top

of leg tube to receive threaded ends of extrusion. Hand tighten with hex key.

CAUTION. Leg tube can be crushed if screw is over tightened.

Max torque is 3--6 ft--lbs. Repeat for second assembly, be sure to orient

extrusion so pencil marks are on the other side.

6. Apply two bumpons to the top of each leg as shown in the illustration. They

go on the side of the extrusion with pencil marks for each assembly.

7. Install end caps into end of each leg. Don’t install end caps into extrusions.

8. Position the strut horizontally between the leg assemblies, as shown in

Figure 4, with the open side of the strut to the back. Line up the short rails

with the back groove in the leg assemblies.

9. Slide the strut down to the base of the tower, adjusting the distance between

the leg assemblies as needed. When complete, make sure the strut is resting

tight against the clear plastic buttons on the leg assemblies.

10. Use the 3/16 inch Allen wrench to tighten the button head screws. Tighten

them first snugly, then go back and tighten them firmly.

NOTE. If you have a torque wrench available, tighten these and all shelf screws

to 60 in⋅lb (6.8 N⋅m) torque.

11. Tip the tower onto its back as shown in Figure 5, resting it on the work

surface by the tops and backs of the leg assemblies.

12. Identify which casters are locking and which are non-locking. The locking

casters, which go on the front of the cart, have an extra tab that you step on

to lock the wheels.

Base Assembly

K475 Workstation Tower Instructions 9

Front

Locking

Casters

1/2 inch Split

Lockwashers

Non-

Locking

Casters

Figure 5: Installing the Casters

13. On the locking casters, place a 1/2 inch split lockwasher on each threaded

shaft, then install the casters into the two front holes in the bottoms of the

leg assemblies. Tighten the casters using the wrench only until they are snug.

14. On the non-locking casters, place a 1/2 inch split lockwasher on each

threaded shaft, then install the casters into the two back holes in the bottoms

of the leg assemblies. Tighten the casters using the wrench only until they

are snug.

15. Return the tower to the upright position.

10 K475 Workstation Tower Instructions

Drawer Shelf and Drawer

Install a drawer shelf and drawer in the tower. You will use these parts:

H1DrawerShelf

H1Drawer

H4 1/4--20 Cap Head Screws, 1/2 inch length

H4 1/4 inch Tooth Lockwashers

H4WeldNuts

H2 Press-Stud Retainers

You will use the 3/16 inch Allen wrench and the circular bubble level included

with your tower.

1. Prepare the drawer shelf as shown in Figure 6 by installing a cap head screw,

a tooth lockwasher, and a weld nut in each of the four side holes of the shelf.

Leave each screw assembly loose; do not screw the weld nut onto the cap

head screw more than one full turn.

Weld Nut

1/4 inch Tooth Lockwasher

1/4--20 Cap Head Screw

Figure 6: Preparing the Drawer Shelf

Drawer Shelf and Drawer

K475 Workstation Tower Instructions 11

2. Position the drawer shelf horizontally between the leg assemblies, as shown

in Figure 7. Position the shelf so the open edge is to the front of the tower.

Front

Figure 7: Aligning the Drawer Shelf

Drawer Shelf and Drawer

12 K475 Workstation Tower Instructions

3. Slide the drawer shelf down to into the position shown in Figure 8. (A light

pencil line has been marked on the insides of the leg assemblies at this

position.) Slide the drawer shelf slowly between the leg assemblies to avoid

scratching the paint. Use the circular bubble level to make sure the shelf is

level.

If you have another person helping you, that person can hold the shelf at the

proper height as you tighten the screws. If you are assembling the tower by

yourself, tighten each screw in turn just enough to hold, and then adjust the

heights one by one until the shelf is positioned properly.

4. Use the 3/16 inch Allen wrench to tighten the cap head screws. Tighten them

first snugly, then go back and tighten them firmly.

Figure 8: Installing the Drawer

ページを読み込んでいます...

Tektronix K475 取扱説明書

関連論文

その他の書類