2. PXN
  3. 9607X
9607X

PXN 9607X 取扱説明書

  • このチャットアシスタントは、Bluetoothコントローラーの取扱説明書の内容を読み込み済みです。このコントローラーの機能、接続方法、充電方法、トラブルシューティングなど、ご不明な点がございましたらお気軽にご質問ください。説明書には、SWITCH、PC、Androidプラットフォームへの接続方法や、振動機能、低電力モードなど、様々な機能が詳しく説明されています。
  • コントローラーの電源のオンオフ方法は？
    SWITCHへの接続方法は？
    Androidへの接続方法は？
    コントローラーの充電方法は？
    低電力状態になったらどうなる？
第1页，总4页
Product use instructions
1.summarize：
The bluetooth controller with vibration is specially designed for the SWITCH platform.Compatible with
PC/ android platform。
2. Functional Characteristics：
2.1 bluetooth 5.0。
2.2 Compatible with SWITCH host platform, PC platform。
2.3 Low power mode (disconnect after sleep)。
2.4 SWITCH host platform has sensor induction function。
2.5 With double motor vibration function。
2.6 The linear transmission distance is over 10 meters。
2.7 Built-in lithium battery 3.7v, can be used for more than 20 hours。
2.8 It can be charged via TYPE-C USB。
3. Product diagram：
第2页，总4页
4. instructions：
4.1 The first step is to turn on the cable Settings in the host as shown below：
4.2 POWER ON/OFF ：
4.2.1 POWER ON： press the "HOME" button for 3 second to activate the controller, and the four LED
racing flashes once per second。
4.2.2 POWER OFF：Press the "HOME" button for 1 seconds to close the controller。
4.3 connect：
4.3.1 SWITCH host press and hold the "Y" button and then press the "HOME" button to start up the
pairing, four LED racing flashing,1 second 2 times, connected to the current LED light long
bright.(LED1 is bright if it is the first machine connection, and LED2 is bright if it is the second,
and so on)。
4.3.2 The android platform, press A and press HOME again. LED2+LED3 Quick flashing,
LED2+LED3 lights up after successful connection。
4.3.3 Connect the gamepad to the computer with the USB Micro data cable, which is the x-input key
value gamepad。
4.4 Low power prompt：
4.4.1 The current connection light flashes twice per second。
4.4.2 Shutdown voltage：3.2V 。
4.5 Charging tips：
4.5.1 Charging in the connected state of the handle: the light in the current mode of the charging line
第3页，总4页
will flash slowly for 1 second and light up normally when fully charged。
4.5.2 DisConnect charging：Insert the charging cable, four LED lights flash once every 1 second,
and four LED lights go out when full。
4.6 Controller sleep function ：
4.6.1 Press the "HOME" button to start up the handle in the reconnect state, and no signal will be
received for 10 seconds to enter sleep。
4.6.2 After connecting the Controller, there will be no keystroke or axis movement for 5 minutes to
sleep。
4.7 Calibration of the Controller：
When the Controlle is off, press the -button, B button and HOME button at the same time. The four
leds of the Controlle are divided into two groups to shine alternately. The Controlle is placed on the
horizontal desktop, and then press the + button。
5. Other parameters：
Search for current：18-26MA
Working current：26MA
Low power alarm：3.5V
Shutdown voltage：3.2V
Sleep current：Less than 50uA
NO.
button
SWITCH code
PC X-INPUT
code
Android code
1
A
A
B
97
2
B
B
A
96
3
X
X
Y
100
4
Y
Y
X
99
5
L
L
LB
102
6
R
R
RB
103
7
-
-
BACK
109
8
+
+
START
108
9
0
screenshots
NO
NO
10
3D press L
3D press L
Thumb L
106
11
3D press R
3D press R
Thumb R
107
12
Z L
Z L
LT
104
13
Z R
Z R
RT
105
第4页，总4页
14
ML-> X (3D VR)
ML-> X (3D VR)
ML-> X (3D VR)
ML-> X (3D VR)
15
ML-> Y (3D VR)
ML-> Y (3D VR)
ML-> Y (3D VR)
ML-> Y (3D VR)
16
MR- >X (3D VR)
MR- >X (3D VR)
MR- >X (3D VR)
MR- >X (3D VR)
17
MR ->Y (3D VR)
MR ->Y (3D VR)
MR ->Y (3D VR)
MR ->Y (3D VR)
18
D-PAD-UP
D-PAD- UP
D-PAD- UP
19
19
D-PAD-DOWN
D-PAD- DOWN
D-PAD- DOWN
20
20
D-PAD-LEFT
D-PAD- LEFT
D-PAD- LEFT
21
21
D-PAD-RIGHT
D-PAD- RIGHT
D-PAD- RIGHT
22
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant t
o part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferenc
e in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not inst
alled and used in accordance with the instructions, may cause harmful interference to radio communications. How
ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and o
n, the user is encouraged to try to correct the interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help important announcement
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable
exposure condition without restriction.
/