Planar PT1710MX ユーザーガイド

PT1710MX

Touchscreen LCD Monitors

USER’S GUIDE

www.planar.com

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may

contain other electronic waste that can be hazardous if not disposed of

properly. Recycle or dispose in accordance with local, state, or federal Laws.

For more information, contact the Electronic Industries Alliance at

WWW.EIAE.ORG. For lamp specific disposal information check

WWW.LAMPRECYCLE.ORG.

1

Usage Notice

Precautions ........................................................................................ 2

Introduction

About Planar’s PT1710MX.. ............................................................... 3

Touch Screen for PT1710MX……………………………………………..4

Package Overview ............................................................................. 5

Installation

Product Overview ............................................................................... 6

VESA Mount for your Monitor…………………………………………….9

Start Your Installation…………………………………………………….10

Connecting the Display………………………………..…………………11

User Controls

Front Panel Controls ........................................................................ 13

How to Use the OSD Menus ............................................................ 14

On-Screen Display Menus ............................................................... 15

Appendix

Troubleshooting ............................................................................... 16

Warning Signal ................................................................................. 17

Product Dimensions ......................................................................... 18

Compatibility Modes ......................................................................... 19

Touch Screen Driver Installation………………………………………..20

Product Registration and Technical Support…………………………..23

Table of Contents

2

Usage Notice

Warning

- To prevent the risk of fire or shock hazards, do not

expose this product to rain or moisture.

Warning

- Please do not open or disassemble the product as

this may cause electric shock.

Precautions

Follow all warnings, precautions and maintenance as recommended

in this user’s manual to maximize the life of your unit.

Do:

 Turn off the product before cleaning.

 Touch screen surface may be cleaned using a soft clean cloth

moistened with mild window glass commercial cleaners or 50/50

mixture of water and isopropyl alcohol.

 Use a soft cloth moistened with mild detergent to clean the display

housing.

 Use only high quality and safety approved AC/DC adapter that

comes with your monitor.

 Disconnect the power plug from AC outlet if the product is not going

to be used for an extended period of time.

Don’t:

 Do not touch the LCD Display screen surface with sharp or hard

objects.

 Do not use abrasive cleaners, waxes or solvents for your cleaning.

 Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic field.

- In direct sunlight.

3

Introduction

About Planar’s PT1710MX

The PT1710MX is a 17” flat panel screen with an active matrix,

thin-film transistor (TFT) liquid crystal display (LCD).

Features include:

 Direct Analog signal input

 Active matrix TFT LCD technology

 1280x1024 SXGA resolution

 17” viewable display area

 31.5 ~ 80 kHz horizontal scan

 56 ~ 75 Hz high refresh rate

 0.264mm x 0.264mm Pixel pitch

 Auto adjustment function

 Multilingual OSD user controls

 VESA DPMS power saving

 Kensington security slot

 100 mm VESA mount

 Removable base for flexible mounting solutions.

 5-wire Resistive touch screen with dual RS-232 Serial/USB controller

 Built-in Speakers-1W/channel.

4

Touch Screen for PT1710MX

 Analog 5-wire resistive touch screen for finger and stylus input

 Surface: Anti-glare treatment

 Interface: Dual RS-232 Serial/USB controller

 Durability: 35 million touches at a single point

 Hardness of surface: 2H MIN (As provided in JIS K5400)

 Operating force: 0.10~1.96N(10g~200g when using a silicon tipped pen

with a 3 mm radius and a hardness of 60)

 Transmittance: 76% (Typ.)

 Driver: Supports Microsoft Windows® VISTA, XP, 2000, ME, 98, NT4.0,

CE, XP Embedded, Linux, Apple® Mac OS

5

Package Overview

LCD Display Power Adapter Power Cord

VGA Signal Cable Audio-in Cable USB Cable

RS-232 Cable Landing Strip Touchscreen Driver

Installation CD-ROM

User’s Guide

6

Installation

Product Overview



Front View



Back View

7

 Connector Ports “A”

 Connector Ports “B”

USB

Audio

input

VGA

input

RS-232

input

DC

Power-in

8

 Kensington Security Slot

The monitor can be secured to your desk or any other fixed object with

Kensington lock security products. The Kensington lock is not included.

9

VESA Mount Your Monitor

This monitor conforms to the VESA Flat Panel Mounting Physical Mounting

Interface Standard which defines a physical mounting interface for flat panel

monitors, and corresponding standards for flat panel monitor mounting

devices, such as wall and table arms. The VESA mounting interface is

located on the back of your monitor.

To mount the monitor on a swing arm or other mounting fixture, follow the

instructions included with the mounting fixture to be used.

Warning!

Please select the proper screws!

The distance between the back cover surface and the bottom of the

screw hole is 8mm. Please use M4 screw diameter with a maximum

length of 8 mm.

10

Start Your Installation





 Remove the Back Cover

Please follow these instructions to remove the cover on the back panel of

the LCD so that you can connect the cables in “Connector Ports A.”

1. To remove the back cover, follow the arrows in Figure A and press with

both your thumbs. The cover should be removed by pressing firmly

along the edges while pulling on the cover.

2. Follow the instructions on P. 11 ( Figure 11.1 ) to connect the cables in

“Connector Ports A.”

3. Fix the cover back to the LCD by pressing firmly until the tabs snap into

place. You may also keep the cables in order by using the cable

organizer.

11

 Connecting the Display (Figure 11.1)

To setup this display, please refer to the following figure and procedures.

1. Be sure all equipment is turned off.

2. Connect the DC power cord to the power connector on the monitor; plug

one end of the AC power cord into the power adapter, and the other end

into an electrical outlet (11.1).

3. Connect the VGA signal cable from the display’s VGA input connector to

the 15-pin connector of your host computer and tighten the screws

(11.1).

4. Connect the Audio-In cable from the audio input port of your display to

the Audio-out port of your computer (11.1).

5. Configure the touch screen. Refer to the “Touch Screen Driver

Installation section on page 20.

6. Once the touch screen is configured, the monitor is ready for use.

To ensure the LCD display works well with your computer, please

configure the display mode of your graphics card to make it less

than or equal to 1280 x1024 resolution and make sure the timing

of the display mode is compatible with the LCD display.

We have listed the compatible “Video Modes” of your LCD display

in the appendix for your reference.

12

Figure 11.1

13

User Controls

Front Panel Controls

No / Icon Control Function

 MENU

Menu button Display the OSD menus

SELECT/AUTO

Select/Auto

Select – To select the adjustment items from

OSD menus.

Auto – To activate the “Auto Adjustment”

function to obtain an optimum image.

 

Brightness

Minus/Minus

1.

Decreases the brightness of the display

image.

2. Decreases value of the adjustment items.

 





Brightness

Plus/Plus

1.

Increases the brightness of the display

image.

2. Increases value of the adjustment items.



Power Switch Switches on/off the

power of the LCD

display.



Power LED

1. Green indicates the display is turned on.

2.

Amber indicates the display is in

power-saving mode.

1.

14

How to Use the OSD Menus

1.

Press the "MENU" button to pop up the “on-screen menu” and to select

among the four Main Menus.

2. Choose the adjustment items by pressing the “Select/Auto” button.

3. Adjust the value of the adjustment items by pressing the “



”or “



“ button.

4. The OSD menu will automatically close, if you have left it idle for a

pre-set time.

5. To disable the OSD menu buttons, please follow the instructions below:

(Please note: the monitor has to be ON with a valid signal preset)

a. Press and hold the “-“ and “Menu” key simultaneously for 4 seconds.

b. The wording “OSD Locked” will appear for 4 seconds on the monitor.

This indicates that all the front buttons, with the exception of the

power button, are now disabled.

6. To enable the OSD menu buttons, please follow the instructions below.

(Please note: the monitor has to be ON with a valid signal present.)

a. Press and hold the “-“ and “Menu” key simultaneously for 4 seconds.

b. The wording “OSD Unlocked” will appear for 4 seconds on the

monitor. This indicates that all the front buttons are now enabled.

15

On-Screen

Display

Menus

Main

OSD

Menu:

MAIN ME

NU

SUB MENU

Function Description

Remark

Auto

-

Adjustment

No/Yes

Choose

this

function

to

obtain

an

optimum

image

.

Contrast 0-100 Adjust

the

contrast

of

the

display

image.

Default 50

Brightness 0-100 Adjusts

the

brightness

of

the

image.

Default 70

Horizontal

Position

0-100 Changes

the

horizontal

position

of

the

image.

Default 50

Vertical

Position 0-100 Changes

the

vertical

position

of

the

image.

Default 50

Clock

0-100

Changes

the

display

data

frequency

to

match

the

frequency

of

your graphic

card

.

W

hen

you

are

experiencing

vertical

flickering

bar

,

use

this function

to

make

an

adjustment.

Default 50

Phase

0-63

Synchronizes

the

signal

timing

of

the

display

to

that

of

the

graphic

card. When

you

are

experiencing

vertical

flickering

image,

use

this

function

to make

an

adjustment.

Display

Mode

ADJ

Select

this

function

to

view

the

display

resolution,

vertical

refresh,

and horizontal

scan

of

the

current

mode

.

OSD

Off

-

Time 5-60 Adjusts

the

time

period

for

OSD

menu

to

disappear

.

Default 30

Language English /

Francais

Deutsch /

Espanol

Italiano /

Japanese

Choose

the

language

you

need.

Default

English

Sharpness 1-4 Adjust

the

sharpness

of

the

image

.

Default 3

Reset

No/Yes

Returns

the

display

parameters

of

the

current

mode

to

its

factory

default settings.

Volume

0-32

Controls

the

sound

volume

.

Default 20

Mute

No/Yes

Disables

the

sound

immediately

.

Color

Setting

9300K /

6500K

Preset /

Custom

Adjusts

the

color

temperature.

Default Preset

Color

Adjustment-Red 0-100 It

allows

you

to

adjust

the

red

color

of

the

display

.

Default 100

Color

Adjustment-Green

0-100 It

allows

you

to

adjust

the

green

color

of

the

display

.

Default 100

Color

Adjustment-Blue

0-100

It

allows

you

to

adjust

the

blue

color

of

the

display

.

Default 100

16

Appendix

Troubleshooting

If you are experiencing trouble with the LCD display, refer to the following. If

the problem persists, please contact your local dealer or our service center.

Problem: No image appears on screen.



Check that all the I/O and power connectors are correctly and well

connected as described in the “Installation” section.



Make sure the pins of the connectors are not crooked or broken.

Problem: Partial Image or incorrectly displayed image.



Check to see if the resolution of your computer is higher than that of the

LCD display.



Reconfigure the resolution of your computer to make it less than or equal

to 1280 x 1024.

Problem: Image has vertical flickering line bars.



Use "Clock" to make an adjustment.



Check and reconfigure the display mode of the vertical refresh rate of your

graphic card to make it compatible with the LCD display.

Problem: Image is unstable and flickering



Use "Phase" to make an adjustment.

Problem: Image is scrolling



Check and make sure the VGA signal cable (or adapter) is securely

connected.



Check and reconfigure the display mode of the vertical refresh rate of your

graphics card to make it compatible with the LCD Display.

Problem: Vague image (characters and graphics)



Use "Clock" to make an adjustment. If this problem still exists, use “Phase”

to make an adjustment.

ページが読み込まれています...

Planar PT1710MX ユーザーガイド

Planar PT1710MX ユーザーガイド

他の言語で

その他のドキュメント