Little Sea-ox
Haier Household Electric Water Heater
Please read this manual before usage.
Retain it for future reference.
0040502335
V:
ES15V-P1
ES25V-P1
ES35V-P1
See to the physical product for the appearance, color or pattern.
Packing list
FAQ
13
13
FAQ & Packing list
Cleaning and maintenance
13
Introduction of control panel
Usage
6
7-13
Attention during installation
6
Installation
Setting environment
4
Safety precautions
3
Dimensions
Technical data
Parameters
2
2
Electric circuit diagram
1
Features
1
Contents
Disconnect the power supply before cleaning. Gently wipe with a wet cloth dipped with a little mild
detergent. Do not use gasoline or other solvents. Finally dry with a dry cloth. Keep the water heater dry.
To ensure high working efficiency, heating elements and tank liner of water heater shall be cleaned once
in three years. Take care not to damage protection layer on heating elements and tank liner surface.
According to different local water qualities, magnesium rods shall be periodically replaced. If
maintenance is needed, please contact your local service station.
13
Usage Cleaning and maintenance FAQ Packing list
Cleaning and maintenance
Usage
FAQ
①No power to heater
①Insufficient water in tank liner
Contact with service department
Check power socket
②Excessive water pressure
②Defective elements
②Defective elements
②Defective sensor
Faulty line
Inconstant water pressure
Check
Check and open
Check and clear
④Defective elements
Phenomenon
Confirmation items
Remedy
No water
Cold outlet
water
Display E1
Display E2
Display E3
Packing list
Name
Quantity
Model
ES15V-P1
ES25V-P1
ES35V-P1
1
1
1
1
1
1
2
2
2
1
1
1
Installation
5-6
Friendly reminder: 1. During long-term out-of-use or maintenance of the heater, you can close city water
pipe valve and set the mixing valve to the highest water temperature rate after opening the safety valve
handle. Move up the safety valve handle to drain the tank.
2. To avoid injury, before next use, it is suggested to first open the hot water valve before switching on the
water heater, exhausting gas possibly retained in the pipeline. In this case, no smoke or fire is permitted
near the open valve. Carefully check and confirm all parts are in good condition.
This mark is the designation of Pre-safe Expert by Haier Water Heater
Company, which indicates use of the company's patented technology inside the
product. It ensures you a safe bath while continuously monitoring whether your
house ground wire is live or not. If this mark is lit, it indicates your house ground
wire was come live (poor grounding and live). In this case, please immediately
stop use and disconnect the power, and remember not to touch any electric
appliance shell in your house. At the same time, immediately contact after-sales
service and your property management company for professional repair until
the mark goes off.
The Pre-safe Expert will become the electric safeguard for your family.
Mark of Haier Safe
Water Heater
Not heated to
desired temperature
or insufficient outlet
water
No water supply or water pressure is too low
Water use point is blocked or hot water valve
is closed
①Hot water access close
①Whether the current function is set to the
proper mode and temperature is set too low.
①Room temperature lower than -20℃
②Temperature not set to desired setting
Calibrate the heater by referring to the
operation instructions in the manual
Calibrate the heater according to the
operation instructions in the manual
Contact with service department when ①, ②
and ③ are excluded.
Calibrate the heater according to the
operation instructions in the manual
Use after flux of mixing valve is turned down
Use after flux of mixing valve is turned down
or use with constant water pressure
Contact with service department when ① is
excluded.
Power on after disconnection when filled with
water
Contact with service department when ① is
excluded.
Cut off power, then connect power when
ambient temperature more than -19℃
Contact with service department when ① is
excluded.
③Heating time limit and setting temperature
not obtain
Inconstant flow and
temperature of
water
Incapable of startup
or display not lit
Safety valve
Drain hose
(Unit)
Electric water
heater
(Set)
Expansion
hook
(PCS)
User's
manual
(Copy)
1
1. High-tech:
Full PC control, digitron display, having functions of instant heating, preset bath, preset
shutdown, power failure auto resume, preset power adjustable; in case of a fault, provided
with alarm abnormity alarm function, display fault code on display, dry heating protection,
electriferous grounding wire alarm function.
2. Safety:
High quality heat proof stainless steel electric heating element, over-temperature protection;
overpressure protection of tank; safe and reliable.
The third-generation “Safe Care” design for safer usage.
3. Durability:
Full plastic shell, handsome and durable
Enamel tank, with reliable quality and long operation life.
4. Convenience:
Adjustable water temperature; adjusting range: 35℃～75℃
5. Multiple usage:
Enclosed structure, capable of supplying water to multiple places like toilet, kitchen etc.
Suitable for family, enterprises, service trades like beauty care on hot water supply (not
drinkable).
6. Nice molding, space-saving:
Vertical type wall-mounting design, saving space
The water heater you purchased is the improved model of the series product. Please operate
according to the user's manual.
L: Live wire (brown)
N: Null line (blue)
MT: Manual reset thermostat
BT: Temperature sensor
EH: Heating element
E: Grounding wire (yellow/green)
Features Electric circuit diagram
Features
Electric circuit diagram
E
Display panel
EH
Relay Relay Relay
RT
MT
E
L
N
Leakage coil
Dear users,
Thanks for choosing a Haier water heater product.
Haier products have good quality and excellent performance. To help you use the product, please
read the manual and operate accordingly. Please retain it for future reference.
The international star service of Haier Group will always accompany you. No matter what kind of
problems you meet during your use, please contact the local after-sales service agent. We are at
your service all the time. Thanks again for choosing a Haier product.
The water heater you purchased may not fully comply with the manual due to the improvement of
the product. We apologize for the inconvenience occurred therefrom.
12
Usage:
4. Holding temperature preset
Without presetting of bath state, when the temperature is set to be less than 55℃, reheating will
be started when the temperature is decreased by 5℃ ; if the temperature is set to be 55~75℃
(including 55℃ and 75℃), reheating will be started when the temperature is decreased by 10℃
5. Shutdown
After bath, press key if you want to stop the heater, then the display will only show the time; or
unplug the power, then all indicators on the display are off.
Note: The time displayed on the figure is only for reference.
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.
Current Temp.
。
。
Heating Temp.
Heating Temp.
。
。
Normal Fast Turbo
Normal Fast Turbo
SPEED
SPEED
SET
SET
TIMER
TIMER
Kw
Kw
.
.
On Off
On Off
:
:
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.Current Temp.
。。
Heating Temp.
Heating Temp.
。。
Normal Fast TurboNormal Fast Turbo
SPEEDSPEED
SET
SET
TIMERTIMER
KwKw
..
On OffOn Off
::
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
(Figure 11)
Press TIMER key three times to select
preset bath, preset shutdown functions.
After heating to set temperature, Heating
Temp indicator stops flashing.
Ten minutes before the preset shutdown time is
up, Off indicator will flash until up to preset time.
Note: if the preset shutdown time is prior to
the preset bath time, the heater will
automatically stop running before the preset
shutdown time is up, then the preset bath
function cannot be realized.
If no operation is made within 2 minutes, the
system will enter into power saving mode.
After setting, clock shows the time and PC
panel displays the current base time.
When entry into heating state, taking 15L heater
as an example, the actual temperature is 30, set
temperature is 55; select power to be 1.0KW, auto
heating will begin about 37 minutes in advance.
Press SET key to adjust preset bath time
when On indicator flashes.
After setting of preset bath time, press
SET key to adjust preset shutdown time.
2
Rated voltage V 230 230 230
Rated pressure Mpa
Rated temperature
Dimension
Waterproof grade
Mixing factor
Tap water pressure
Diameter of power wire
Outlet rate of hot water
24h fixed COP
Volume
Power
Net weight
Rated frequency Hz 50 50 50
0.80
1000/ 2000/ 3000
0.80
0.80
W
Kg
75
10
15
IPX4
No less than 0.05MPa
See to Figure 1
3×1.5
14
25
17
35
L
mm
mm
/
/
/
/
℃
%
Dimensions
2
Parameters
Parameters Dimensions
316
291
623 152 100
378 362 616 152 100
415 398 663
200
100
Remarks: The permitted error or limit of above parameters is ±10%.
Remarks: The permitted error or limit of net weight above is ±10%.
A Hot water outlet B Cold water inlet C Tank D Heating element E Anode rod
F Thermometer tube G Wall-mounting bracket
b
a
C
d
e
E
F
D
C
G
AB
11
Usage
Current Temp.
Current Temp.
Current Temp.
Current Temp.
Current Temp.
Current Temp.
。
。
。
。
。
。
Heating Temp.
Heating Temp.
Heating Temp.
Heating Temp.
Heating Temp.
Heating Temp.
。
。
。
。
。
。
Normal Fast Turbo
Normal Fast Turbo
Normal Fast Turbo
Normal Fast Turbo
Normal Fast Turbo
Normal Fast Turbo
SPEED
SPEED
SPEED
SPEED
SPEED
SPEED
SET
SET
SET
SET
SET
SET
TIMER
TIMER
TIMER
TIMER
TIMER
TIMER
Kw Kw Kw
Kw
Kw
Kw
.
.
.
.
.
.
On Off
On Off
On Off
On Off
On Off
On Off
:
:
:
:
:
:
(Figure 1)
(Figure 10)
③Simultaneous setting of preset bath and preset shutdown mode (On/Off)
The lighting of all On/Off indicators indicates that both preset bath and preset shutdown
functions are selected.
In active state (figures on display flash and On/Off indicators are off), press TIMER key three
times, then On/Off indicators all light, press SET key to preset bath and shutdown time. When
presetting bath time, On indicator flashes; when presetting shutdown time, Off indicator flashes.
After setting, if no operation is made within 2 minutes, the system will enter into power saving
mode and only On/Off and clock on display light. When up to the preset heating time calculated
by the system, the heater will automatically heat and the Heating Temp indicator on display
flashes. Ten minutes before the preset shutdown time is up, the Off indicator will flash until
automatic shutdown at the preset time.
Preset bath and preset shutdown are provided with power failure auto resume function.
For example: preset bath time is set to be 18:30, the preset shutdown time 22:00.
(As shown in Figure 11)
Item Unit ES15V-P1 ES25V-P1 ES35V-P1
Press TIMER key twice.
Note: when the display shows everything normally
and the Off indicator is on, the heater will
automatically stop running when set time is up.
Ten minutes before the preset shutdown time is up,
the Off indicator will change to flash from constant
lighting until shutdown up to the preset time.
If no operation is made within 2 minutes, the system
will enter into power saving mode.
If the current temperature is lower than the set
temperature, Heating Temp will flash in power
saving mode.
Press SET key to set time.
After setting, clock shows the time and PC
panel displays the current base time.
Average temperature
of hot water outlet
Re-heating time
(temperature rise 50℃)
1000/ 2000/ 3000
1000/ 2000/ 3000
75
75
See to Figure 1 See to Figure 1
No less than 0.05MPa No less than 0.05MPa
IPX4 IPX4
3×1.5 3×1.5
Front view
Side view
Cutaway view
Rear view
Model
a
b
c d e
ES15V-P1
ES25V-P1
ES35V-P1
3
Safety Precautions
Safety Precautions
In case the power cord of the water heater
is damaged, be sure to have it replaced by
after service technicians with special cord
offered by the manufacturer.
Check if the ammeter and the diameter of the
wires are in accordance with the rated current
of the water heater. If necessary, please have it
checked by an experienced electrician.
Be sure to use independent socket and earth it
reliably, and socket quality shall conform to
national standard requirements.
The product adopts the patent “Safe Care” technology of our company. As long as adopting
civil power supply, even if the earthing wire is electrified by mistake, the “Safe Care” technology
still can block the dangerous electricity, and ensure your personal safety. But if you find any
perceptible current, please disconnect the power and contact after service department for
maintenance. Do not disassemble by yourself.
Description of the Symbols
Never do that.
Be sure to act as per instructions.
Set the power socket of the water heater
at dry position away from water spraying.
Do not plug/unplug with wet hands.
This water heater is available for AC
230/50Hz power.
In winter of cold area, if the heater is idle for a long
period, please pull the handle of safety valve to
discharge the water. Otherwise it may freeze
inside the water heater and cause damage.
In opening and closing the water valve, do
not point the shower head toward the
human body. Otherwise it way hurt by the
spraying hot water.
completely with water before switching on the
power in the first usage. Children must take a
bath under the supervision of an adult.
After installation,
be sure to fill the
heater
NO
Usage
10
Current Temp.
Current Temp.Current Temp.
Current Temp.
。
。。
。
Heating Temp.
Heating Temp.Heating Temp.
Heating Temp.
。
。。
。
Normal Tur boFast
Normal Tur bo Fast Normal Fast Turbo
Normal Fast Turbo
SPEED
SPEEDSPEED
SPEED
SET
SETSET
SET
TIMER
TIMERTIMER
TIMER
Kw
KwKw
Kw
.
..
.
On Off
On OffOn Off
On Off
:
::
:
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.
。
Heating Temp.
。
Normal Tur bo Fast
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
(Figure 9)
②Preset shutdown mode setting (Off)
In active state (figures on display do not flash and On/Off indicators are off), press TIMER key
twice, then Off indicator lights, press SET key to preset bath time, wherein the default of initial
preset shutdown time is 00:00. After setting, if no operation is made within 2 minutes, the system
will enter into power saving mode and only Off and clock on display light. Ten minutes before the
preset shutdown time is up, the Off indicator will flash until automatic shutdown at the preset
time.
Note: before the time for preset shutdown, instant heating and other functions are active.
For example: preset the shutdown time is set to be 22:00. (As shown in Figure 10)
V23
0
5
0
H
z
Press TIMER key to enter into
preset bath mode.
After heating to set temperature, Heating
Temp indicator stops flashing.
If no operation is made with 2 minutes, the
system will enter into power saving mode
(unique function in preset mode).
After setting, clock shows the time and PC
panel displays the current base time.
When entry into heating state, taking 15L heater
as an example, the actual temperature is 30, set
temperature is 70, auto heating will begin about
25 minutes in advance.
Press SET key to set time.
Adjust the power of SPEED key into
2.0Kw, then press key to regulate the
temperature to be 70℃.
8
4
Description of the Symbols
Never do this.
Be sure to act as per instructions.
Setting Environment
Setting Environment
4. Power setting
In active state (figures on display do not flash), press SPEED key to select power,
continuously pressing of this key leads to cyclical selection: Normal (1.0Kw), Fast (2.0Kw),
Turbo (3.OKw) three powers; select one power, the power fully lights.
For example: the power is regulated from 1.0Kw to 3.0Kw. (As shown in Figure 8)
9
Usage
Current Temp.
Current Temp.
。
。
Heating Temp.
Heating Temp.
。
。
Normal Fast Turbo
Normal Fast Turbo
SPEED
SPEED
SET
SET
TIMER
TIMER
Kw
Kw
.
.
On Off
On Off
:
:
(Figure 8)
5. Setting of preset bath/preset shutdown (On/Off)
①Setting of preset bath mode (On)
In active state (figures on display do not flash and On/Off indicators are off), press TIMER
key to select preset bath mode, then On indicator lights, press SET key to preset bath time,
wherein the initial preset bath time is 00:00. In preset bath mode, water using time is based
on the time displayed on computer panel, power and set temperature can be set by the
customers themselves. If not set, the system will run at the power and temperature set
before bath presetting. After setting of preset bath time, the time is converted into the base
time of the computer panel. If no operation is made within 2 minutes, the system will enter
into power saving mode and only On and clock on display will be lit. In power saving mode,
press any key to enter into normal interface. Heating Temp indicator flashes when entry into
heating state from power saving mode.
The heater is provided with auto heating function. The system automatically calculates the
time required for heating to set temperature according to the heating power set by the
customer, and then determines the starting time for heating. Before water using time set,
automatically heat to set temperature and stop heating when up to set temperature.
Note: if the actual water temperature is less than the set temperature after getting at the
preset time, the system will automatically prolong the heating time for another 30 minutes,
and will stop heating after 30 minutes no matter whether the set temperature is obtained.
If the actual temperature is up to the set temperature before the preset time and the preset
time is still not up after the actual temperature is decreased by 5℃, the heater will perform
heating again, and stop heating after arrival of preset time no matter whether the set
temperature is obtained.
For example: preset bath time is set to be 18:30, the temperature is 70℃ and power is
2.0Kw. (As shown in Figure 9)
Do not set it at a place too cold; it may freeze.
Do not use as floorstanding appliances.
Do not install at places without sewage.
The original pipeline of the water heater is an organic part of “Safe Care”. Do not remove it by
yourself. Otherwise we will not take responsibility for injury and loss caused.
Do not set at outdoor places.
Please mount it to a firm and reliable wall.
Connect the drain hose to the inlet of the
sewer to avoid polluting by splashing.
Press
SPEED
key twice
to adjust
the
power
from
1.0Kw to
3.0Kw.
3. Time setting
In active state (figures on display do not flash and On/Off indicators are off), directly press SET
key to select time function, then set time by pressing and . The setting range of hour
figure is 00~23, that of minute figure is 00~59. Press or once, then for the figure to be
set add or reduce 1. The figure to be set will continuously increase or decrease under
continuous pressing. Hour figure circulates from 00 to 23 as per 24H system, minute figure
changes circularly from 00 to 59. When time is set by pressing SET key, hour figure shall be
set firstly: hour figure flashes and the figure is set by pressing or , if there is no
operation within 6 seconds or the hour figure is confirmed by pressing SET key directly, hour
figure will become constant lighting state from flashing. Afterwards, minute figure begins
flashing, press or to set minute. If there is no operation within 6 seconds or the minute
figure is confirmed by pressing SET key directly, minute figure will start constant lighting state
from flashing, indicating the completion of temperature (疑为时间即：time) setting.
Note: if keys other than SET are selected when the figure flashes (within 6s), the flashing state
setting will not work and the figure will return to the original state before setting.
For example: in case of initial power-on startup state, the time of the heater is adjusted to be
11:10. (As shown in Figure 7)
5
8
Usage
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Current Temp.
Current Temp.
。
。
Heating Temp.
Heating Temp.
。
。
Normal Fast Turbo
Normal Fast Turbo
SPEED
SPEED
SET
SET
TIMER
TIMER
Kw
Kw
.
.
On Off
On Off
:
:
Current Temp.
Current Temp.
Current Temp. Current Temp.
。
。
。 。
Heating Temp.
Heating Temp.
Heating Temp. Heating Temp.
。
。
。 。
Turb o
Turb o
Turb o Turb o
SPEED SPEED
SPEED
SPEED
SET
SET
SET SET
TIMER TIMER TIMER
TIMER
Kw
Kw
Kw Kw
.
.
. .
On Off
On Off
On Off On Off
:
:
: :
(Figure 7)
Installation must be made by installers of or designated by our company after-service
department. The water heater shall be wall-mounted.
Make 2 holesφ12mm, 65mm deep in wall with an impact drill according to installation
dimension. Insert and fix expansion hooks in corresponding wall holes. Lift the water heater.
Make wall rack correspond to the hooks. Hang the ring of extended connection line onto a
hook and hand the wall rack (see Figure 2). Install accessories such as safety valve as shown
in Figure 3. Use sealing compound to prevent water leakage.
To facilitate installation and removal, it is suggested a G1/2” movable nut is fitted at
appropriate locations on inlet and outlet pipes respectively. Find the location requiring hot
water supply. Connect inlet pipe, outlet pipe and city water pipe respectively to the use point
for hot water.
Note: The hot water pipe shall not be too long to reduce the heat losses.
Please reserve some space in installation for the future maintenance.
Connection and use of safety valve:
The safety valve should be connected to the water inlet pipe. Please check carefully if the
direction is correct after installation. The correct direction of installation is that the arrowhead
on the safety valve should point to the water heater.
Please connect the drain hose to the safety valve. Connect one end of the hose to the safety
valve vent and the other end to the sewage drain for fear of indoor contamination. The hose
can be cut short or extended as necessary. The hose shall be installed as inclined downward.
The heater should work with the safety valve whose rated pressure is 0.80MPa. When the tap
water pressure is no less than 0.80MPa, a large amount of water may flow out from the drain
hose of the safety valve, which indicates water pressure is overly high and after-service
department shall be notified for a solution.
Installation
Installation
(Figure 2)
Hot water outlet
Safety valve
Extended connection line
Wall rack
(Figure 6)
Expansion
hook
(Figure 3) for installation
reference only.
Hot water
outlet
valve
Cold
water
outlet
valve
Mixing
valve
Shower
head
Cold water
inlet
Press key to adjust the temperature into
55. (pressing time can be ignored)
Press SET key to directly confirm or automatically
confirm the time if no operation within 6 seconds.
Press SET key, the n hour figure fl ashes
(pressing time ca n be ignored) .
Adjust hour figure to 11 and confi rm it,
then minute figur e begins flas hing.
Similarly, adju st minute figure to 10 an d
confirm it, then ti me setting is c ompleted.
Normal Fast Turbo
Normal Fast Turbo
Normal Fast Turbo Normal Fast Turbo
Temperature setting
In active state (figures on display do not flash), press and to set temperature with the set
temperature ranging from 35℃ to 75℃. Press or once, then for the temperature to be set
add or reduce 1. The temperature to be set will continuously increase or decrease under
continuous pressing with the figure circulating 35℃ to 75℃. When setting temperature, current
set temperature figure flashes. If there is no operation within 6 seconds or the temperature is set
by directly pressing SET key to confirm the desired temperature, set temperature figure will
become constant lighting state from flashing, indicating the completion of temperature setting.
Note: if keys other than SET are selected when the figure flashes (within 6s), the current setting
does not work and the figure returns to the original state before setting.
For example: the current set temperature of the heater is 40℃ , now the temperature will be
adjusted to 55℃. (As shown in Figure 6)
8
6
Please fasten the drain hose to the pressure relief hole of
safety valve by twisting (see to Figure 4). Connect the
other end of drain hose to the sewer to avoid polluting the
room by splashing. When the power is switched on, and
the water heater starts operating, there may be some
water discharged from the pressure relief hole of the safety
valve. It is due to the water expansion under heating, and
is normal phenomenon. The pressure relief pipe shall
communicate with the air directly. Do not block it. The drain
hose connecting to safety valve shall be kept downward
sloping in installation and in a frost-free environment.
Safety precautions:
1. Do not confuse the water inlet and outlet pipes. The water bearing the water heater shall be
strong enough to endure a weight twice as much as that of water heater filled with water. Do
not secure it by means of adhesive or similar products because the fixation by such methods
is unreliable.
2. To avoid danger caused by accidental reset of heating breaker, the power for the heater
cannot be supplied by timer and other external switch devices or connected to circuit with
frequent switching for facility use.
3. If any part is damaged, please contact the local maintenance agent and have it replaced with
our spare part.
4. Tap water inlet pressure shall be no less than 0.05MPa and the maximum pressure shall not
exceed 0.75MPa.
Connect to drain hose
(Figure 4)
During heating, water may drip from the drain hose of the pressure relief hole due to
expansion and the hole must be left open to the atmosphere. Check safety valve once a
month as follows: move the small handle of safety valve, if there is water flowing out, safety
valve is normal; if there is no water flow, please contact local after-sales service station.
The pressure relief hole is to be operated regularly to remove lime deposits and to verify that it
is not blocked.
Installation
Attentions in installation
Installation Attentions in installation Introduction of control panel
Introduction of control panel
1
2
3
4
5
6
7
8
9
10
11
Be sure to check and confirm that the tank is filled with water, there is no leakage at each joint
and the power supply complies with the stipulation before switching on the power.
7
Usage
Usage
After installation, as the tank is empty in the first usage, be sure to open the tap water inlet valve
and any outlet of the heater. When the tank is filled with water or other water outlet keeps water
outputting (which indicates the tank is filled with water), please close water outlet, check if there is
water leakage at each joint and plug the power.
1. Startup
After power connection, fully display for 1 second and buzzer sounds for indication, then enter
into shutdown state (clock displayed only). For the first time power-on, the clock displays the
system default time 00:00 (hour figure and minute figure constantly light and “:” in the middle
flashes). In shutdown state, press key to enter into working state. For the first time of
startup, the system displays initial state, wherein the initial state defaulted by the system is: set
temperature shows 75℃æ actual temperature shows the ambient temperature of the sensor;
power shows 3.0Kw.
For example: actual temperature is 35℃æ℃æ; time shows 00:00. (As shown in Figure 5)
Note: in heating state, Heating Temp indicator flashes; in holding state, Heating Temp
indicator lights constantly.
(Figure 5)
SPEED
SET
TIMER
:
Current Temp.
。
Heating Temp.
。
Normal Fast Turbo
SPEED
SET
TIMER
Kw
.
On Off
:
Curre nt Temp.
。
Heating Temp.
。
Norm al Fast Turb o
SPEE D
SET
TIM E R
Kw
.
On Off
:
SPEED
SET
TIMER
Current Temp.
。
Heating Temp.
。
Turb o
SPEED
SET
TIMER
Kw
.
On Off
:
After power connection, display shows everything for 1s.
。
1. Actual temperature
2. Set temperature
3. Power
4. Current time
5. Clock, temperature figure increase key
6. Power selection key
7. Time setting key
8. On/Off key
9. Preset bath, preset shutdown setting
key
10. Clock, temperature figure decrease key
11. Preset bath, preset shutdown (On:
preset bath; Off: preset shutdown)
After 1s,
enter into
shutdown
state.
(Note: for
the next
power
connectio
n, the
clock will
show the
current
base time
of the PC
panel set
before
the
power
failure the
last time.)
In shutdown state, press key to start up the heater
for running, other keys do not work at this time.
Normal Fast Turbo
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Haier ES15V-P1 ユーザーマニュアル
- カテゴリー
- 給湯器
- タイプ
- ユーザーマニュアル
他の言語で
- English: Haier ES15V-P1 User manual
