GV-RKV1355-QMA-20220421
651.00K1.0701.11106
Quick Start Guide
快速安裝手冊
快速安裝手冊
GV-RKV1355
Ver. 1.0
RS-485/WIEGAND PROXIMITY READER
Reader x 1
讀卡機
讀卡機
產品包裝內容與數量依產品別而略有不同,實際內容以產品包裝物為準。
產品包裝內容與數量依產品別而略有不同,實際內容以產品包裝物為準。
Quick Start Guide x 1
快速安裝手冊
快速安裝手冊
Package Contents /包裝內容/
包裝內容
1
Kindly ensure the product's contents upon unpacking; please refer to this quick start guide regarding the product 's
specifications and important notices.
the items described below are the standard packaging.
打開包裝確認產品包裝內容,並請詳細閱讀此手冊,認識產品規格特性與注意事項。
打開包裝確認產品包裝內容,並請詳細閱讀此手冊,認識產品規格特性與注意事項。
Physical Dimension /外觀尺寸/
外觀尺寸
2
Installation /安裝/
安裝
3
Wiring Connections /接線/
接線
4
Scale:mm
www.hundure.com
www.hundure.com
One Y 產品保固證明書
產品保固證明書One Year Limited Warranty / /
我們保固此產品於購買日起一年之內因為材料上或是生產製造中所產生的缺陷，所造成的外觀上，或是功能上的缺陷及故障問題。若是您在此保固期限之內發現此類
問題，請聯絡本公司的服務人員，退回此產品，我們將替您免費維修或是更換產品。
當您退回此產品時，請依照原始的包裝方式包裝此產品，或是給予同等級的包裝保護；若是我們收到此產品時，產品上沒有出廠時的序號標籤，或是產品已經拆開或與出廠時有任何不
同，這個保固將變得無效。
此保固不包含天然的，以及人為的破壞或改變 、或是意外事故、不正常操作、誤用、濫用等外在因素所造成的損壞。
此保固不包含不當的操作或保養，不當的連結至其他設備，或是由本公司以外的人員企圖修復此產品。
起因於使用這種產品，在間接、特別、次要因素，或者隨之發生，造成伴隨著軟件或其它文檔的損害，本公司的責任在任何情況下都不得超過這產品的售價。
關於產品的軟件和文檔編制的全部內容，本公司並沒有表示保證或法定它的性能、暢銷性、或者適用於任何特別的目的。
本公司保留權利修正或者不斷改進它的產品，軟件或者文檔編製無義務通知任何個人或者購買者。
我們保固此產品於購買日起一年之內因為材料上或是生產製造中所產生的缺陷，所造成的外觀上，或是功能上的缺陷及故障問題。若是您在此保固期限之內發現此類
問題，請聯絡本公司的服務人員，退回此產品，我們將替您免費維修或是更換產品。
當您退回此產品時，請依照原始的包裝方式包裝此產品，或是給予同等級的包裝保護；若是我們收到此產品時，產品上沒有出廠時的序號標籤，或是產品已經拆開或與出廠時有任何不
同，這個保固將變得無效。
此保固不包含天然的，以及人為的破壞或改變 、或是意外事故、不正常操作、誤用、濫用等外在因素所造成的損壞。
此保固不包含不當的操作或保養，不當的連結至其他設備，或是由本公司以外的人員企圖修復此產品。
起因於使用這種產品，在間接、特別、次要因素，或者隨之發生，造成伴隨著軟件或其它文檔的損害，本公司的責任在任何情況下都不得超過這產品的售價。
關於產品的軟件和文檔編制的全部內容，本公司並沒有表示保證或法定它的性能、暢銷性、或者適用於任何特別的目的。
本公司保留權利修正或者不斷改進它的產品，軟件或者文檔編製無義務通知任何個人或者購買者。
型號
型號Model
Warranty will be valid only after filling out this form and stamped or signed by reseller!
此保固書必須填妥各項內容,並且蓋有經銷商印鑑始為有效.
此保固書必須填妥各項內容,並且蓋有經銷商印鑑始為有效.
/ / 序號
序號Serial no. / / 購買日期
購買日期Date of Purchase / / 經銷商
經銷商Reseller stamp / /
We warrants this product against defect in material or workmanship for 1 year from the date of purchase. If such a defect is discovered within this warranty limitation,
contact your direct vendor for repair or replacement of your unit.
When returning the product, you must ship the product in its original packaging or packaging that gives an equal degree of protection. This warranty becomes invalid if
the factory-supplied serial number has been removed or altered on the product.
This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence or modification of any part of the product. This
warranty does not cover damage due to improper operation or maintenance, connection to improper equipment, or attempted repair by anyone other than We.
In no event shall We liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential, damages resulting from the use of the
product the product, its accompanying software, or it's documentation. We makes no warranty or representation expressed, implied, or statutory, with respect to its
products,contents of use of this documentation and all accompanying software, and specially disclaims its quality , performance, merchantability or fitness for any
particular purpose. We reserves the right to revise or update its product, software or documentation without obligation to notify any individual or entity.
C
B
A
Case Sensor/防拆除Sensor/防拆除Sensor
調整讀卡機 NODE ID 請打開後蓋的螺絲,零件位置如後圖示意。
零件位置依照機型別而有所不同,請依實際零件編號做識別。
調整讀卡機 NODE ID 請打開後蓋的螺絲,零件位置如後圖示意。
零件位置依照機型別而有所不同,請依實際零件編號做識別。
Before mounting the reader onto desired location. Please set the NODE ID (DIP Switch, binary number system).
The position of the components varies according to the reader's model. Kindly take note of the components during
setup.
B
C
讀卡感應區
讀卡感應區
Reading Area
A
NODE ID Settings, refer to the chart below.
讀卡機NODE ID,請依照下表做配置
讀卡機NODE ID,請依照下表做配置
Node ID Configuration/開關位址/
開關位址
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
000000
100000
010000
110000
001000
101000
011000
111000
000100
100100
010100
110100
001100
101100
011100
111100
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Color Wiegand RS-485
Pin
Red/紅/
紅
Black/黑/
黑
Yellow/黃/
黃
Deep Blue/深藍/深
藍
Gray/灰/
灰
Pink/粉紅/
粉紅
White & Black
白黑/
白黑
Orange/橙/
橙
Brown/棕/
棕
Purple/紫/
紫
White/白/
白
Green/綠/
綠
Red & Black
紅黑/
紅黑
Light Blue
淺藍/
淺藍
DC+12V IN
Ground
DC+12V IN
Ground
RS-485+
RS-485-
W0
W1
Ground
-
Beep Control
Case Sensor GND (To Controller GND)
Case Sensor (To Controller Case Sensor)
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Plate x 1
固定板
固定板
Hex Key wrench x 1
六角扳手/螺絲
六角扳手/螺絲
Screw x 3
Warning
Please pay attention to two sides to avoid
your hands getting injured while installing
or removing the device.
/安全警語/
拆裝時請注意兩端，以免受傷
拆裝時請注意兩端，以免受傷
安全警語：
(B)
(C)
(D)
(E)
Kindly refer to the “ wiring connections”wiring connections for
the NODE ID settings before the hardware installation.
Do not over tighten the back plate screws during installation to
prevent distortion.
(A) Mount the back plate onto the wall or other desired location.
(B) Connect the wires in accordance with the wiring instruction
below.
(C) Make sure the back plate and the reader upper cover guides
are aligned.
(D) Install the reader upper cover to the back plate.
(E) Using the hex key wrench, fasten the screw onto the bottom
of the reader.
4
安裝前請先參考 " 接線" 設定讀卡機NODE ID號。
安裝讀卡機固定板時,請勿用力過大以避免造成彎曲變形。
(A). 將安裝固定板固定在牆上或其他位置。
(B). 依照接線說明將線接上,並將各接線端子插上。
(C). 讀卡機上方對準固定板卡榫。
(D). 將讀卡機往固定板方向密合。
(E). 使用六角扳手將螺絲由下方將底部密合鎖上。
4
安裝前請先參考" 接線" 設定讀卡機NODE ID號。
安裝讀卡機固定板時,請勿用力過大以避免造成彎曲變形。
(A). 將安裝固定板固定在牆上或其他位置。
(B). 依照接線說明將線接上,並將各接線端子插上。
(C). 讀卡機上方對準固定板卡榫。
(D). 將讀卡機往固定板方向密合。
(E). 使用六角扳手將螺絲由下方將底部密合鎖上。
4
1 2 3 4 5 6
Green LED Control
*
*
*Do not use the same set of twisted pairs.
不可使用同一組絞線.
不可使用同一組絞線.
106.3
83.5
98.0
75.0
48.5
24.5
20.0
14.5
21.2
60.5
84.5
44.6
22.0
27.6
122.0
122.0
88.0
ON=1, OFF=0
ON
1 2 3 4 5 6
● Dip(6) is card format selection.
ON is for reading the document, and
OFF is for reading the serial
number.
●Dip(6) 是卡片格式選擇。 ON 為讀
取文檔，OFF 為讀取序號。
●Dip(6) 是卡片格式選擇。 ON 為
讀取文檔，OFF 為讀取序號。
Dip(6)
Note:
1. Kindly use minimum 22AWG double-shielded aluminum mylar foil twisted pair cable for the connection between
the reader and the controller.
2. In order to reduce long distance noise,The isolated net of transmission cable should connect to both ends of
device ground.
3. The distance between two readers should be over 30cm to prevent radio frequency interference from
each other.
4. Mounting the device around metal could affect read range. Metal of any type around the device should be
avoided while mounting.
5. The distance between the reader and the controller should not exceed 30 meters.
6. For optimum read range, kindly use DC Linear power adaptor for the reader's power supply.
7. In order to ensure the reader's normal operation, input voltage should be between 12V±10%.
8. If the reader is installed in an open area or highly humid environment, it is recommended to protect the reader
with an external shielding cover.
9. RS-485 communication Baud rate is 9600.
備註：
1. 讀卡機與控制器之間請使用22AWG以上的雙隔離網鋁箔麥拉對絞傳輸線。
2. 為了減低遠距離雜訊，傳輸線的隔離網地應接兩端裝置的地。
3. 建議兩個讀卡機之間的距離最少30公分以上。
4. 避免安裝在金屬物週邊，以免影響感應距離。
5. 讀卡機與控制器的距離建議不要超過30米。
6. 供應讀卡機之電源,建議使用非交換式的線性直流電源,以確保得到最佳的感應距離。
7. 為確保讀卡機的正常運作,輸入電源請確保在12V±10%之間。
8. 如安裝在露天或高濕度易滲水的環境,建議另行加裝防水罩。
9. RS-485 通訊Baud rate 為9600。
備註：
1. 讀卡機與控制器之間請使用22AWG以上的雙隔離網鋁箔麥拉對絞傳輸線。
2. 為了減低遠距離雜訊，傳輸線的隔離網地應接兩端裝置的地。
3. 建議兩個讀卡機之間的距離最少30公分以上。
4. 避免安裝在金屬物週邊，以免影響感應距離。
5. 讀卡機與控制器的距離建議不要超過30米。
6. 供應讀卡機之電源,建議使用非交換式的線性直流電源,以確保得到最佳的感應距離。
7. 為確保讀卡機的正常運作,輸入電源請確保在12V±10%之間。
8. 如安裝在露天或高濕度易滲水的環境,建議另行加裝防水罩。
9. RS-485 通訊Baud rate 為9600。
N/A
(A)
www.hundure.com
Testing /測試/
測試
5
打開電源亮紅色燈,同時聽到“嗶”聲提示
打開電源亮紅色燈,同時聽到“嗶”聲提示
When the power is on, the reader's red LED
and the reader will beep concurrently.
將卡片靠近讀卡機,同時聽到“嗶”聲提示.
將卡片靠近讀卡機,同時聽到“嗶”聲提示.
Place the card provided near the reader.
The reader will beep concurrently.
Card
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the
following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or
modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
(Example - use only shielded interface cables when connecting to
computer or peripheral devices)
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may
cause undesired operation.
/
