Z01
型多功能充电支架
Z01 Multifunctional Charging Stand
（适用于苹果 iPhone /手表/ airpods）
(For iPhone/Apple Watch/AirPods)
感谢您购买我们的多功能充电支架。
Thanks for choosing this multifunctional charging stand.
特征
Features
1。可用来收取您的 Apple 手表。在同一时间的 iPhone 和 airpods
1. Charge Apple Watch, iPhone and AirPods at the same time.
2 整理你的电缆，使你的桌子干净整洁。
2. Organize charging cables, which makes your table clean and tidy.
3 底部防滑垫提高了整机的稳定性
3. The slide-proof mat increases stability of the stand.
4.45 的完美角度允许你使用你的手表放在床头柜上的模式
4. Charge Apple Watch at a 45-degree angle, which is easy to look at the time.
5 完美的苹果 airpods，苹果手表系列 2 / 1 系列/耐克+ /运动/版，iPhone 7/7 Plus，iPhone
6 /6 西格玛加/硒/ 5s/5c / 5 等。
5. Compatible With:
1) Apple Watch Series 1/2/3, Apple Watch Nike+, Apple Watch Hermès, Apple Watch
Edition
2) iPhone X, iPhone 8/8 Plus, iPhone 7/7 Plus, iPhone 6s/6s Plus, iPhone 6/6 Plus,
iPhone 5/5s/5c, iPhone SE, etc.
3) AirPods
附件清单
:
Package Content:
NO
物料名称
Related
Component
数量
Quantity
产品图片
Picture
○
1
底板
Base
1
○
2
耳机充电座
Charging Station A
1
○
3
充电线固线头 A
Lightning Cable
Holder A
1
○
4
充电线固线头 B
Lightning Cable
Holder B
1
○
5
手表充电座组件
Charging Station B
1
○
6
挡块
Block
1
○
7
手机充电座
Charging Station C
1
○
8
背靠板
iPhone Backboard
1
○
9
背靠板螺钉
Screw for iPhone
Backboard
1
○
10
M3*5 五金螺钉
M3*5 Metal Screw
11
○
11
M3*4 塑胶螺钉
M3*4 Plastic
Screw
2
○
12
1M APPLE
数据线
Apple Lightning
Cable (1m/3.3Ft)
2
组装说明：
Assembly Instruction:
Please follow the steps below to install.
1 底板与档块的固定：
1. Fix the Block on the Base with one M3*5 Metal Screw.
2 手机充电座与 APPLE 数据线的固定：
2. Fix the Apple Lightning Cable on the Charging Station C with
one M3*4 Plastic Screw.
3 手机充电座与底板的固定：
3. Fix the Charging Station C on the Base with two M3*5 Metal
Screws.
4 背靠板锁紧到底板上：
4. Fix the iPhone Backboard on the Base with the Screw for
iPhone Backboard.
5 充电线固定头 A/B 与 APPLE 数据线的固定：
5. Fix the Lightning Cable on the Lightning Cable Holder A/B with
one M3*4 Plastic Screw.
6 充电线固定头 A/B 与耳机充电座的固定：
6. Fix the Lightning Cable Holder A/B on the Charging Station A
with two M3*5 Metal Screws.
7 耳机充电座与底板的固定：
7. Fix the Charging Station A on the Base with two M3*5 Metal
Screws.
8 手表充电座组件与 iWatch 无线充的固定：
8. Fix your Apple Watch Wireless Charger on the Charging Station
B.
9 表充电座组件与底板的固定：
Apple Watch Wireless Charger
9. Fix the Charging Station B on the Base with four M3*5 Metal
Screws.
10 把下部数据卡入到底板底部的卡线槽内：
10. Put all three cables in to the wire ways then connect with USB
chargers.
○
12
Cable of Apple Watch
Wireless Charger
Connect with USB
Chargers
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
