ALEKO DS2252-HD ユーザーマニュアル

1

DS-225 series

2

Contents

1. Warning & Statements。。。。。。。。。。。。。。。。。。。。。。。。。。。。。

2. Voltage。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。

3. Device Application。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。

4. Technical Specifications。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。

5. Structure Overview。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。

6. Installation & Sandpaper Replacement。。。。。。。。。。。。。。。

7. Installation & viscid disc Replacement。。。。。。。。。。。。。。。

8. Connection Set for Dust Outlet。。。。。。。。。。。。。。。。。。。。。。

9. Switch& Speed Governor Operation。。。。。。。。。。。。。。。。。

10. The operation of the edge angle 。。。。。。。。。

11. Folding installation and disassembly。。。。。。。

3

12. Suction adjustment。。。。。。。。。。。。。。。。

13. LED light (Optional)。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。

14. Application Diagram。。。。。。。。。。。。。。。。。。。。。。。。。。。

15. Cleaning。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。

16. Replacement of carbon brush。。。。。。。。。。。。。。。。。。。。

1) Work area

a) Keep work area clean and well lit. Cluttered

and dark areas may result in an accident.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control of the powered tool and may

cause bodily injury.

4

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce the risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock and may make

the tool inoperative.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tools in a damp location is

unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3) Personal safety

5

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

bodily injury.

b) Use safety equipment. Always wear eye

protection. Safety equipment such as dust mask,

non-skid safety shoes, hard hat, protective

eyewear, or hearing protection used for

appropriate conditions will reduce personal

injuries.

c) Avoid accidental starting. Ensure the switch is

in the off position before plugging in. Carrying

power tools with your finger on the switch or

plugging in power tools that have the switch on

will result in an accident and cause bodily injury.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in bodily injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry

or long hair can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

6

ensure these are connected and properly used.

Use of these devices can reduce dust related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will deliver better results and safer at

the rate for which it was designed for.

b) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

c) Disconnect the plug from the power source

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tools operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

7

are less likely to bind and are easier to control;

g) Use the power tool, accessories and tool bits

etc., in accordance with these instructions and

in the manner intended for the particular type

of power tool, taking into account the working

conditions and the work to be performed. Use

of the power tool for operations other than it was

intended for could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Safety Warnings Specific for Sanding Operations:

a) Do not use excessively oversized sanding disc

paper. Follow manufacturer’s recommendations,

when selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a

laceration hazard and may cause snagging, tearing of

the disc or kickback

1． Voltage

Before connecting electric tool to the socket, make

sure the supply voltage is in accordance with rated voltage.

If the former is greater than latter and the device is powered

on by mistake, it may result in damage of devices and in

bodily injury. As for indefinite supply voltage of socket,

never try to plug it for use. Besides, the damage to the

8

devices, may also occur if the supply voltage falls below

rated voltage.

2. Device Application

As one of our products, the device belongs to the

hand-held electric tools.

The device mainly caters for lime surface, including

the interior wall, ceiling, exterior wall, corridor, etc.

Remove the painting lime mud from the wall, and make the

surface even or smooth. It may promote the wall grinding

efficiency and quality by workers.

With various conditions taken into consideration in the

design, the device may run at high or low speed. In addition,

you may adjust the connection structure at high and low

locations respectively, to optimize the grinding efficiency

and realize user-friendly and compact design.

3. Technical Specifications

Model DS-225A DS225AVS DS225-2 DS-2252VS

Rated Voltage 110（V~）

Frequency 60（Hz）

Rated Power 750（W）

No-load Speed 800-1750(R/min)

Sandpaper Dimensions Ф225（mm）

Spindle Thread M14

Safety Standard II /

Net/Gross Weight 13.8（Lbs）

Model DS-225A DS225AVS DS225-2 DS-2252VS

Rated Voltage 110（V~）

9

Frequency 60（Hz）

Rated Power 750（W）

No-load Speed 800-1750 (R/min)

Sandpaper Dimensions Ф225（mm）

Spindle Thread M14

Safety Standard II /

Net/Gross Weight 13.8（Lbs）

4．Structure Overview (See following pictures)

Complete appliance

DS-225 28.7x10.8x17.5（in/2pc） Length 4.1FT/5.5FT

10

DS-225AVS 28.7x10.8x17.5（in/2pc） Length 4.1FT/5.5FT

11

DS-225-2 44x11x7.4（in/1pc）Length 4.1FT/6.2FT

12

DS-2252VS 44x11x7.4 ( in/1pc ) Length 4.1FT/6.2FT

13

DS-225-2 Plastic viscid disc component

2. Sandpaper

4. Speed governor 3.Switch

14

5. Dust Outlet 6.Vacuum dust hose

7. Handle

8. Lengthening bar

15

9. Locking nut

1 Plastic viscid disc component

2 Sandpaper

3 Switch

4 Speed governor

5 Dust Outlet

6 Vacuum dust hose

7 Handle

8 Lengthening bar

9 Locking nut

Standard Accessories

Drywall: 1pc Instruction manual: 1pc

Sandpaper: 6pcs Allen Wrench: 1pcs

Carbon Brush: 2pcs Telescopic Dust hose: 4 m/1pcs

Dust bag: with self-cleaning with 1

16

5. Installation & Sandpaper Replacement (See following

picture)

Note: Prior to installation or removing the sandpaper,

make sure to not only switch off the device, but also cut off

the power supply.

17

——Installation Guide

To ensure the replacement procedures, place the

device on smooth and even ground prior to installation.

Take the sandpaper from the toolbox, and attach it onto the

disk. The back of the sandpaper (Item 1) will automatically

glue with the disk/adhesive disk (Item 2), making both

connection and conduction available.

In order to promote the grinding efficiency, it is

necessary to change the sandpaper after the device has been

operational for a certain period. Firstly, switch off the

device and disconnect from the socket. Then, remove the

previous sandpaper entirely from the disk, to lay new

sandpaper neatly as well as facilitate future replacement. At

last, fix new sandpaper in position.

——Sandpaper Overview

Grinding towards the target wall and object is possible

with abrasive grains and sandpaper twisting upon

operations. The sandpaper is classified into various

categories per its dimensions. It is recommended to select

the sandpaper in accordance with actual size of the disk.

The more abrasive grains included on the sandpaper, result

in flatter and smoother surface, and can be achieved via

grinding, while the grinding efficiency will fall accordingly

and vice versa. Therefore, the sandpaper (Ф225mm) is

recommended upon actual needs.

Warning ： Prior to the sandpaper replacement or

installation please read safety precautions and installation

guides carefully.

18

6. Installation & viscid disc Replacement (See following picture)

If the viscid disc is damaged during use, a new viscid disc

can be purchased from our company for replacement. 。

——Installation Guide

Viscid disc

Remove the sandpaper, put the Allen wrench into the

hexagon hole in the center of the viscid disc and then rotate

anticlockwise to take off the damaged viscid disc. Install

the new viscid disc (see the picture).

7. Connection Set for Dust Outlet (See following

pictures)

19

a Component b Lock

b a

As the name implies, it is used for connecting the

device to Dust Outlet (accessory). The dust will come out

from the wall upon operating the grinder. The device is

connected to Dust Collector in the back via Connection Set

for Dust Outlet, making it possible for the operator to

20

reduce the amount of dust.

——Installation Guide

Plug the component b into component, make the lock in the

groove and rotate clockwise.

——Dismantling Process

Rotate the lock anticlockwise and pull out the dust hose

8. Switch & Speed Governor Operation

The switch of the machine is a two step switch. As shown in

following picture, press the switch button and push forward to

power on. Press the switch button and turn back to power off.

The Speed Governor, as shown in the following picture, may be

used to regulate the speed, to facilitate the operations of workers

and improve work quality simultaneously.

Speed Governor Switch

ページが読み込まれています...

ALEKO DS2252-HD ユーザーマニュアル

このマニュアルも適しています

ALEKO DS2252-HD ユーザーマニュアル

他の言語で

その他のドキュメント