Dell PowerEdge 2900 ユーザーガイド

Dell™ PowerEdge™

2900 Systems

Information Update

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Intel

and Xeon are registered trademarks of Intel Corporation; Microsoft, Windows, and Windows Server

are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or

other countries; Red Hat and Red Hat Enterprise Linux are registered trademarks of Red Hat, Inc.;

SUSE is a registered trademark of Novell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

May 2009 P/N YC469 Rev. A06

Contents 3

Contents

PowerEdge 2900 III – New System Features . . . . . . . 5

New Performance Features

. . . . . . . . . . . . . 5

New I/O and Storage Features

. . . . . . . . . . . . 5

New Security Features

. . . . . . . . . . . . . . . . 5

Optional Internal USB Memory Key

. . . . . . . . . . . . 6

Installing the Optional Internal USB

Memory Key

. . . . . . . . . . . . . . . . . . . . . 7

Processor Upgrades – PowerEdge 2900 II

and PowerEdge 2900 III Systems

. . . . . . . . . . . . . 9

System Board Replacement – Safeguarding

Encrypted Data

. . . . . . . . . . . . . . . . . . . . . . . 9

System Message Update

. . . . . . . . . . . . . . . . . 10

LCD Status Messages Update

. . . . . . . . . . . . . . 14

System Setup Program Update

. . . . . . . . . . . . . 19

Memory Screen

. . . . . . . . . . . . . . . . . . . 19

CPU Information Screen

. . . . . . . . . . . . . . 20

Integrated Devices Screen

. . . . . . . . . . . . . 20

System Security Screen

. . . . . . . . . . . . . . 21

Serial Communication Screen

. . . . . . . . . . . 22

4 Contents

Operating System Information . . . . . . . . . . . . . . 22

Enumeration of NICs

. . . . . . . . . . . . . . . . 22

SATA Optical Drive Support on RHEL3

and SLES9

. . . . . . . . . . . . . . . . . . . . . . 23

RHEL – Incorrect Processor Information

. . . . . . 23

System Support for Microsoft Windows 2000

. . . 23

Hardware Owner’s Manual Updates

. . . . . . . . . . 24

Installing the Processor

. . . . . . . . . . . . . . . 24

System Diagnostics Custom Test Options

. . . . . 24

System Board Replacement Update

(Service-Only Procedure)

. . . . . . . . . . . . . . . . 24

Information Update 5

This document provides updated information for your system

on the following topics:

• New system features for

PowerEdge™ 2900 III systems

• Internal USB memory key for

PowerEdge 2900 III systems

• Processor upgrades for

PowerEdge 2900 II and PowerEdge 2900 III

systems

• System board replacement – safeguarding encrypted data

• System message update for

PowerEdge

2900 III system

• LCD status message update for

PowerEdge

2900 III systems

• System Setup program update for

PowerEdge

2900 III systems

• Operating system information

•

Hardware Owner’s Manual

updates

• System board replacement (service-only procedure)

PowerEdge 2900 III – New System Features

New Performance Features

• Two dual-core or quad-core Intel

®

Xeon

®

processors.

New I/O and Storage Features

• Optional Intel quad-port Gigabit Ethernet NIC, capable of supporting

10-Mbps, 100-Mbps, and 1000-Mbps data rates, and iSCSI remote boot.

• Support for 10 Gb Ethernet cards.

• One internal USB 2.0-compliant connector supporting an optional

bootable USB flash drive or USB memory key.

• Support for optional SAS 6i/R and PERC 6/i adapters.

New Security Features

• Trusted Program Module (TPM) support for improved security.

• Optional support for iSCSI boot.

6 Information Update

Optional Internal USB Memory Key

The PowerEdge 2900 III system provides an internal USB connector located

on the system board for use with a USB flash memory key (see Figure 1-1).

The USB memory key can be used as a boot device, security key, or mass

storage device. To use the internal USB connector, the Internal USB Port

option must be enabled in the Integrated Devices screen of the System Setup

program. See "Integrated Devices Screen" on page 20.

Figure 1-1. Internal USB Connector Location

1 system board 2 internal USB connector location

1 2

Information Update 7

To boot from the USB memory key, you must configure the USB memory

key with a boot image and then specify the USB memory key in the boot

sequence in the System Setup program. See “

Using the System Setup

Program” in the

Hardware Owner’s Manual

. For information on creating

a bootable file on the USB memory key, see the user documentation that

accompanied the USB memory key.

NOTE: USB keys that contain multiple LUNs (Logical Unit Numbers) must

be formatted using the format utility provided by the key manufacturer.

NOTICE: To avoid interference with components inside the system, the USB key

must conform to the following maximum dimensions: 12.7mm thick (0.5”) x 30.48mm

width (1.2”) x 71.12mm length (2.8”).

Installing the Optional Internal USB Memory Key

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your Product

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

1

Turn off the system, including any attached peripherals, and disconnect

the system from its electrical outlet.

2

Open the system. See “Opening the System” in the

Hardware Owner’s

Manual

.

3

Locate the USB connector on the system board, and insert the USB

memory key into the USB connector. See Figure 1-2.

8 Information Update

Figure 1-2. Installing an Internal USB Key

4

Close the system. See “Closing the System” in the

Hardware Owner’s

Manual

.

5

Reconnect the system to power and restart the system.

6

Enter the System Setup program and verify that the USB key has been

detected by the system. See “Using the System Setup Program”

in the

Hardware Owner’s Manual

.

1 USB memory key 2 internal USB connector

9

8

1

2

Information Update 9

Processor Upgrades – PowerEdge 2900 II

and PowerEdge 2900 III Systems

• If the front of your system chassis is labeled with a “II”, your system is

upgradeable to the 5100 series of dual-core Intel Xeon processors and

the 5300 series of quad-core Intel Xeon processors.

• If the front of your system chassis is labeled with a “III”, your system is

upgradeable to the 5100 and 5200 series of dual-core Intel Xeon processors

and the 5300 and 5400 series of quad-core Intel Xeon processors.

See support.dell.com for information on the latest processor upgrade options

for your system.

System Board Replacement –

Safeguarding Encrypted Data

On PowerEdge 2900 III systems using Windows Server

®

2008, you can use

encryption programs, such as the BitLocker utility, to secure the contents

of the hard drive.

If you are using the TPM with an encryption program, you are prompted to

create a recovery key during system setup. Be sure to store this recovery key.

If you replace the system board, you must supply the recovery key when you

restart your system before you can access the encrypted files on your hard

drive(s).

10 Information Update

System Message Update

Table 1-1 lists new system messages for the PowerEdge 2900 III system

and the probable cause and corrective action if the message appears.

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your Product

Information Guide for complete information about safety precautions,

working inside the computer, and protecting against electrostatic discharge

Table 1-1. System Messages

Message Causes Corrective Actions

Alert! Node

Interleaving

disabled! Memory

configuration does

not support Node

Interleaving.

The memory configuration

does not support node

interleaving, or the

configuration has changed

(for example, a failed

DIMM) so that node

interleaving cannot be

supported.

The system

runs but with reduced

functionality.

Ensure that the memory

modules are installed in a

configuration that supports

node interleaving. Check

other system messages

for additional information

for possible causes.

For memory configuration

information, see

“General Memory Module

Installation Guidelines”

in the Hardware Owner’s

Manual. If the problem

persists, see

“Troubleshooting System

Memory” in the Hardware

Owner’s Manual.

!!*** Error: Remote

Access Controller

initialization

failure *** RAC

virtual USB devices

may not be

available...

Remote Access Controller

initialization failure

Ensure that the Remote

Access Controller is

properly installed. See

“Installing a RAC Card”

in the Hardware Owner’s

Manual.

Invalid PCIe

card found in the

Internal_Storage

slot!

The system halted because

an invalid PCIe expansion

card is installed in the

dedicated storage controller

slot.

Remove the PCIe expansion

card and install the internal

SAS controller in the

dedicated slot.

Information Update 11

No boot device

available

Faulty or missing optical

drive subsystem, hard drive,

or hard-drive subsystem, or

no bootable USB key

installed.

Use a bootable USB key,

CD, or hard drive. See

“Using the System Setup

Program” in the Hardware

Owner’s Manual for

information on setting

the order of boot devices.

PCI BIOS failed

to install

PCIe device BIOS (Option

ROM) checksum failure

detected during shadowing.

Cables to expansion card(s)

loose; faulty or improperly

installed expansion card(s).

Reseat the expansion

card(s). Ensure that all

appropriate cables are

securely connected to the

expansion card(s). If the

problem persists, see

“Troubleshooting System

Expansion Cards” in the

Hardware Owner’s Manual.

PCIe Degraded

Link Width Error:

Embedded device

Expected Link

Width is n

Actual Link

Width is n

Faulty system board

or riser board.

See “Getting Help” in the

Hardware Owner’s Manual.

PCIe Degraded

Link Width Error:

Integrated device

Expected Link

Width is n

Actual Link

Width is n

The specified PCIe device is

faulty or improperly

installed.

For a SAS controller

daughter card, reseat the

card in the dedicated PCIe

connector. See “Installing

a SAS Controller Daughter

Card” in the Hardware

Owner’s Manual. If the

problem persists, see

“Getting Help” in the

Hardware Owner’s Manual.

Table 1-1. System Messages (continued)

Message Causes Corrective Actions

12 Information Update

PCIe Degraded Link

Width Error: Slot n

Expected Link

Width is n

Actual Link

Width is n

Faulty or improperly

installed PCIe card in

the specified slot.

Reseat the PCIe card in the

specified slot number. See

“Expansion Cards” in the

Hardware Owner’s Manual.

If the problem persists,

see “Getting Help” in the

Hardware Owner’s Manual.

PCIe Training

Error: Embedded

device

Faulty system board

or riser board.

See “Getting Help” in the

Hardware Owner’s Manual.

PCIe Training

Error: Integrated

device

The specified PCIe device

is faulty or improperly

installed.

For a SAS controller

daughter card, reseat the

card in the dedicated PCIe

connector. See “Installing a

SAS Controller Daughter

Card” in the Hardware

Owner’s Manual. If the

problem persists, see

“Getting Help” in the

Hardware Owner’s Manual.

PCIe Training

Error: Slot n

Faulty or improperly

installed PCIe card

in the specified slot.

Reseat the PCIe card in the

specified slot number. See

“Expansion Cards” in the

Hardware Owner’s Manual.

If the problem persists,

see “Getting Help” in the

Hardware Owner’s Manual.

Remote Access

Controller cable

error or incorrect

card in the RAC

slot.

RAC cables not connected,

or RAC card installed in

wrong expansion slot.

Check that the RAC cables

are connected, and that the

RAC card is installed in the

correct expansion slot.

See “Installing a RAC Card”

in the Hardware Owner’s

Manual.

NOTE: All TPM information messages appear after the BMC option ROM has been

loaded during POST.

Table 1-1. System Messages (continued)

Message Causes Corrective Actions

Information Update 13

TPM configuration

operation honored.

System now resets. Information only.

TPM Failure

A Trusted Platform Module

(TPM) function has failed.

See “Getting Help” in the

Hardware Owner’s Manual.

TPM operation is

pending. Press I

to Ignore or M to

Modify to allow

this change and

reset the system.

WARNING: Modifying

could prevent

security.

Configuration change

has been requested.

Press I to continue system

boot. Press M to modify the

TPM setting and restart.

Warning: Following

faulty DIMMs

are disabled:

DIMM n

1

n

2

Total memory size

is reduced.

Faulty or improperly

seated memory module(s).

DIMMs are disabled in

pairs, as indicated by the

n

1

and n

2

. Check both

DIMMs for a possible fault.

See “Troubleshooting

System Memory” in the

Hardware Owner’s Manual.

Warning: A fatal

error has caused

system reset!

Please check the

system event log!

A fatal system error

occurred and caused the

system to restart.

Check the SEL for

information that was logged

during the error. See the

applicable troubleshooting

section in See

“Troubleshooting Your

System” in the Hardware

Owner’s Manual. for any

faulty components specified

in the SEL.

Warning! No micro

code update loaded

for processor n

Micro code update failed. Update the BIOS firmware.

See “Getting Help” in the

Hardware Owner’s Manual.

Table 1-1. System Messages (continued)

Message Causes Corrective Actions

14 Information Update

LCD Status Messages Update

Table 1-2 lists updates to the LCD status messages that can occur on

the PowerEdge 2900 III system and the probable cause for each message.

The LCD messages refer to events recorded in the system event log (SEL).

For information on the SEL and configuring system management settings,

see your systems management software documentation.

Warning: The

installed memory

configuration is

not optimal. For

more information

on valid memory

configurations,

please see

the system

documentation

on the technical

support web site.

Invalid memory

configuration. The system

runs but with reduced

functionality.

Ensure that the memory

modules are installed in

a valid configuration. See

“General Memory Module

Installation Guidelines”

in the Hardware Owner’s

Manual. If the problem

persists, see

“Troubleshooting System

Memory” in the Hardware

Owner’s Manual.

Write fault

Write fault on

selected drive

Faulty USB device, USB

medium, optical drive

assembly, hard drive, or

hard-drive subsystem.

Replace the faulty media.

Reseat the USB device or

USB cable. For hard drive

problems, see

“Troubleshooting a Hard

Drive” in the Hardware

Owner’s Manual.

Table 1-1. System Messages (continued)

Message Causes Corrective Actions

Information Update 15

Table 1-2. LCD Status Messages

Code Text Causes Corrective Actions

N/A SYSTEM NAME

A 62-character string that

can be defined by the user

in the System Setup

program.

The SYSTEM NAME

displays under the

following conditions:

• The system

is powered on.

• The power is off

and active errors

are displayed.

This message is for

information only.

You can change the

system ID and name

in the System Setup

program. See “Using the

System Setup Program”

in the Hardware Owner’s

Manual.

E1000 FAILSAFE,

Call Support

Check the system event

log for critical failure

events.

See “Getting Help” in

the Hardware Owner’s

Manual.

E1118 CPU Temp

Interface

The BMC is unable to

determine the CPU(s)

temperature status.

Consequently, the BMC

increases the CPU fan

speed to maximum

as a precautionary

measure.

Turn off power to the

system and restart the

system. If the problem

persists, see “Getting

Help” in the Hardware

Owner’s Manual.

E1211 ROMB Batt

RAID battery is either

missing, bad, or unable to

recharge due to thermal

issues.

Reseat the RAID battery

connector. See the “RAID

Battery” and see

“Troubleshooting System

Cooling Problems” in

the Hardware Owner’s

Manual.

E1625 PS AC Current

Power source is out

of acceptable range.

Check the AC power

source.

16 Information Update

E1711 PCI PERR B##

D## F##

The system BIOS has

reported a PCI parity error

on a component that

resides in PCI

configuration space

at bus ##, device ##,

function ##.

Remove and reseat the

PCIe expansion cards.

If the problem persists,

see “Troubleshooting

an Expansion Card”

in the Hardware Owner’s

Manual.

PCI PERR

Slot #

The system BIOS has

reported a PCI parity error

on a component that

resides in the specified

PCIe slot.

Reinstall the expansion-

card riser. See “Expansion

Card Risers” in the

Hardware Owner’s

Manual.

If the problem persists,

the riser card or system

board is faulty. See

“Getting Help”

in the Hardware Owner’s

Manual.

E1712 PCI SERR B##

D## F##

The system BIOS has

reported a PCI system

error on a component that

resides in PCI

configuration space at bus

##, device ##, function

##.

Remove and reseat the

PCIe expansion cards.

If the problem persists,

see “Troubleshooting

Expansion Cards” in

the Hardware Owner’s

Manual.

PCI SERR

Slot #

The system BIOS has

reported a PCI system

error on a component

that resides in the

specified slot.

Reinstall the expansion-

card riser. See “Expansion

Card Risers” in the

Hardware Owner’s

Manual.

If the problem persists,

the riser card or system

board is faulty. See

“Getting Help” in

the Hardware Owner’s

Manual.

Table 1-2. LCD Status Messages (continued)

Code Text Causes Corrective Actions

Information Update 17

E171F PCIE Fatal Err

B## D## F##

The system BIOS has

reported a PCIe fatal error

on a component that

resides in PCIe

configuration space at bus

##, device ##, function

##.

Remove and reseat the

PCIe expansion cards.

If the problem persists,

see “Troubleshooting

Expansion Cards” in

the Hardware Owner’s

Manual.

PCIE Fatal Err

Slot #

The system BIOS has

reported a PCIe fatal error

on a component that

resides in the specified

slot.

Reinstall the expansion-

card riser. See “Expansion

Card Risers” in the

Hardware Owner’s

Manual.

If the problem persists,

the riser card or system

board is faulty. See

“Getting Help” in the

Hardware Owner’s

Manual.

E1914 DRAC5 Conn2

Cbl

DRAC 5 cable is missing

or disconnected.

Reconnect the cable. See

“Installing a RAC Card”

in the Hardware Owner’s

Manual.

E1B01 USB#

Overcurrent

Device plugged in the

specified USB port caused

an overcurrent condition.

Reseat the device cable.

If the problem persists,

replace or remove the

device.

E2110 MBE DIMM # & #

One of the two indicated

DIMMs has had a memory

multi-bit error (MBE).

See “Troubleshooting

System Memory” in

the Hardware Owner’s

Manual.

Table 1-2. LCD Status Messages (continued)

Code Text Causes Corrective Actions

18 Information Update

NOTE: Each diagnostic LCD message is assigned a priority. The highest priority

messages supersede any group of messages with a lower priority.

E2111 SBE Log

Disable DIMM #

The system BIOS has

disabled memory single-

bit error (SBE) logging,

and does not resume

logging further SBEs until

the system is restarted.

“#” represents the DIMM

implicated by the BIOS.

See “Troubleshooting

System Memory”

in the Hardware Owner’s

Manual.

E2112 Mem Spare

DIMM #

The system BIOS has

spared the memory

because it has determined

that the memory had too

many errors. “# & #”

represents the DIMM pair

implicated by the BIOS.

See “Troubleshooting

System Memory”

in the Hardware Owner’s

Manual.

I1915 Video Off

(LCD lights with

a blue or amber

background.)

The video is turned off by

the RAC remote user.

Information only.

I1916 Video Off

in ##

(LCD lights with

a blue or amber

background.)

The video is turned off in

xx seconds by the RAC

remote user.

Information only.

Table 1-2. LCD Status Messages (continued)

Code Text Causes Corrective Actions

Information Update 19

System Setup Program Update

Memory Screen

Table 1-3 lists the descriptions for the information fields that appear

on the Memory Information screen.

Table 1-3. Memory Information Screen Options

Option Description

System Memory Size Displays the amount of system memory.

System Memory Type Displays the type of system memory.

System Memory Speed Displays the system memory speed.

Video Memory Displays the amount of video memory.

System Memory Testing Specifies whether system memory tests are run at system

boot. Options are Enabled and Disabled.

Redundant Memory

(Disabled default)

Enables or disables the redundant memory feature.

When set to Spare Mode, the first rank of memory on

each DIMM is reserved for memory sparing. Redundant

memory feature is disabled if the Node Interleaving field

is enabled.

Node Interleaving

(Disabled default)

If this field is set to Enabled, memory interleaving is

supported if a symmetric memory configuration is

installed. If this field is set to Disabled, the system can

support Non-Uniform Memory architecture (NUMA)

(asymmetric) memory configurations.

NOTE: The Node Interleaving field must be set to Disabled

when using the redundant memory feature.

Low Power Mode

(Disabled default)

Enables or disables the low power mode of the memory.

When set to Disabled, the memory runs at full speed.

When set to Enabled, the memory runs at a reduced

speed to conserve energy.

20 Information Update

CPU Information Screen

Table 1-4 updates the description for the Demand-Based Power Management

option.

Integrated Devices Screen

Table 1-5 lists new Integrated Devices screen options.

Table 1-4. CPU Information Screen

Option Description

Demand-Based Power

Management

(Enabled default)

NOTE: Check your operating system documentation to

verify if the operating system supports this feature.

Enables or disables demand-based power management.

When enabled, the CPU Performance State tables are

reported to the operating system; when disabled, the CPU

Performance State tables are not reported to the operating

system. If any of the CPUs do not support demand-based

power management, the field becomes read-only, and is

automatically set to Disabled.

Table 1-5. Integrated Devices Screen Options

Option Description

Internal USB Port

(On default)

Enables or disables the system’s internal USB port.

OS Watchdog

Timer

(Disabled default)

NOTE: This feature is usable only with operating systems that

support WDAT implementations of the Advanced Configuration

and Power Interface (ACPI) 3.0b specification. Microsoft

®

Windows Server

®

2008 supports this feature, but Windows

Server 2003 does not.

Sets a timer that monitors the operating system for activity and

aids in recovery if the system stops responding. When this field

is set to Enabled, the operating system is allowed to initialize

the timer. When set to Disabled, the timer is not initialized.

I/OAT DMA

Engine

(Disabled default)

Enables or disables the I/O Acceleration Technology (I/OAT)

option. When set to Enabled, I/OAT reduces system CPU

usage for applications that use TCP by offloading part of TCP

receive operation to the DMA engine.

ページを読み込んでいます...

Dell PowerEdge 2900 ユーザーガイド

関連論文

その他の書類