12g
故障/
BREAK DOWN
射擊/
SHOOTING
www.kwcgun.com
KIEN WELL TOY INDUSTRIAL CO., LTD
SINCE 1978
MADE IN TAIWAN
Use hexagonal wrench to remove the
magazine cap by counter clockwise.
Release the
magazine.
Push the
button
Turn the magazine cap a
out counter-clockwise
and place CO2 cartridge
B inside the magazine.
Rapidly turn the screw A clockwise when
piercing the cartridge in the magazine.
逆時針轉出彈匣底內件
後，置入小鋼瓶B，再
以順時針方向鎖緊彈匣
底內件A。當刺破鋼瓶
出氣時，請快速鎖緊。
4.
Maximum BB capacity is 18 rounds.
Load BBs one by one.
Loading BBs
Insert fully loaded magazine in the airgun until
you hear the sound of “CLICK”.
Bad quality BB is the main reason to cause
BB jam. Please use the best quality KWC
BB to avoid jamming problem.
When BB jammed, first please release the
magazine from pistol then use a soft stick
(diameter no bigger than 4.4mm) to clear up
the barrel.
Pulling trigger will load BB in the barrel.
Therefore, please do not pull the trigger half
way and release the trigger. This action could
load 2 BBs in the pistol and cause jamming.
Please avoid dry firing, for it could cause
parts deformed or damage.
此低動能遊戲用槍是針對喜愛射擊運動
的消費者所開發。避免因使用方法不正確或
改造所發生的故障或事故，請務必詳讀說明
書，正確的操作享受愉快的射擊運動。
This airgun is intended for recreational or
training purposes.To prevent improper
handling, modification or alteration
causing malfunction or accident, please
read the owner’s manual carefully. Enjoy
the pleasant shooting experience by
proper operation.
1.除了發射時外，不要將手指頭掛在板機上。
2.選擇安全與適當標靶
3.在非使用期間，請保持保險關閉且退彈的狀態，
就算在非使用狀態，也要如同其己裝彈。
4.如任何的機械產品，槍的保險也可能失效。即使
在保險關閉的狀態下也請小心的操作此槍，請勿
將槍口對人。
5.千萬不要對堅硬或平坦表面、水面射擊，以避免
跳彈。
6.請妥善保管產品在未成年孩童無法伸手取得的場
所。
7.每次使用前後都應該檢查擋彈物，假如擋彈物表
面有磨損失效或是反彈時請停止使用。
8.請使用高品質BB彈，請勿使用 口徑大於4.4mm
表面不平滑的 重複使用過的BB彈 非本說
明書指名的發射物。
9.最高的使用及儲藏CO2小鋼瓶環境為50∘C(122∘
F)以內，高溫可能會造成CO2小鋼瓶過熱甚至爆
炸。
10.檢查任何掉落之槍枝，以確保未影響其功能。
1.Do not put your finger on the trigger except shooting.
2.Please choose safe and proper target.
3.Please always keep the airgun on safe and unloaded when
not using.
4.Like all mechanical devices, an airgun safety can fail.
Always handle the airgun safely even when the safety is “on
safe”. Never point the airgun at any people.
5.Avoid ricochet. Never shoot at a hard or flat surface or at
water.
6.Keep the airgun out of reach for small children.
7.Your backstop should be inspected for wear before and
after each use. Discontinue use of the backstop if surface
shows signs of failure or ricochet.
8.Only use high quality 4.5mm steel BBs. Never use BB
diameter larger than 4.4 mmBB with unsmoothed surface
reused BB that has been firedincorrect projectiles not
design for this airgun
9.Do not expose CO2 cartridges to heat or store them at
temperatures above 50∘C(122∘F). CO2 cartridges may
over heat or explode at temperatures above 50∘C(122∘F).
10.Check any gun that has been dropped to ensure that its
function has not been affected.
台南市仁德區義林路168巷89號
NO.89, LN. 168, YILIN RD.,
RENDE DIST., TAINAN CITY
71752, TAIWAN (R.O.C.)
TEL+886-6-2798175
FAX+886-6-2798176
www.kwcgun.com
AAKCMD44 INSTRUCTION MANUAL
AAKCMD44 系列說明書
For your safefy, please read this manual carefuly before use.
1. 推開卡榫
2. 取出彈匣
使用六角鈑手反時針方向取出彈匣底內
件。
最多可裝18粒。
7.
填裝B.B彈。
6.
為了使擊發順暢，填裝
方法是讓B.B彈在彈匣中一粒接著一粒。
拉下滑粒。
5.
3.
1.
將裝好B.B彈的彈匣插入槍身往上推入，直到
彈匣卡榫發出"卡嚓"為止。
瞄準目標物扣引鈑機，即可擊發。
2.
※注意:在長期不使用的狀態下，請將彈
匣內氣體洩放掉。
可射擊
保險
1.不良的B.B彈是造成卡彈的原因，請使用
品質優良的KWC B.B彈。
2.當卡彈時，請盡可能先取出彈匣，再以不
傷槍管的軟質細棒(不可大於4.4mm直徑)
從槍口置入清除。
3.空擊發易造成零件損耗，請避免此動作。
5.使用一段時間後，請再次用中性矽油脂潤
滑撞針及鈑機軸心。
4.當扣引鈑機時，此時B.B彈即同時在上膛
階段，不可扣引一半時又回復，因為如此
的動作，將有可能上膛兩發B.B彈。
Do not display this pistol in public—it may confuse people and may be a crime.
Always wear eye
protection when
using airgun.
使用低動能遊戲
用槍前，請務必
戴上保護眼鏡或
面罩。
★使用低動能遊戲
用槍前，請務必
詳讀說明書內容
。
Read the owner’s
manual before
using the airgun.
Never brandish or aiming this airgun at any
people or domestic animals. Brandish this
airgun in public is dangerous and may be a
crime.
★請不要在公開場合使用低動能遊戲用槍
，也請不要拿低動能遊戲用槍對準人或
動物。
★不可攜帶低動能
遊戲用槍在公共
場所行走，請務
必裝在袋子或盒
子內。
Always transport an
airgun in a locked
carrying case.
Make sure it is
unloaded and on
safe.
★請不要由槍口向
內探視。
To Avoid accidental
discharge, do not
look directly into the
barrel.
★請確認後再發射BB彈方向，附近無人
或動物存在。
Always be aware of your surrounding
before and during shooting and select a
safe area for target practice.
Disassemble, modify, or alter of your airgun
may cause malfunction, void your warranty
and may make it unsafe to use.
★不可任意改造或加工低動能遊戲用槍，
私自改造加工會造成產品損壞、保固
失效，導致使用上不安全，甚至觸法
送辦。
AAKCMD44
系列零件表
AAKCMD44 SERIES PARTS LIST
AAKCMD44 SERIES EXPLORED VIEW
AAKCMD44
系列零件分解圖
警 告
K08-00691-9 2019© 06
Spare parts may be modified for quality improvement
And such modification may be without advance notice.
P09
P23
P26
P42
P44
KM44-
P45
Z01
Z02
Z03
Z04
Z05
Z07
Z10
Z11
Z21
Z46
Z48
B003
B03
B04
B05
B41
KM44-
B06
UKG01-
P31
KCB75-
B16
UKG01-
B19
KG47-
F401
KG12-
B215
EB004
F01
F02
KG47-
F401
S01
S03
S05
S07
S08
S09
S10
KG47-
S404
KM47-
S471
SM2
EA004
EA020
EA061
EA064
EA066
EA087
ED008
E08
R01
G001
G005
G006
G013
G022
U1
U2
U3
保險配件
槍柄
彈匣底座配件
心棒蓋迫緊
彈匣滑粒
前槍管套(小孔)
槍管內套
本體(左)
本體(右)
鈑機
保險(左)
撞針
鈑機連動件
保險固定件
彈匣卡榫
擊鐵
槍管連動件
彈匣
鋼珠
撞針軸
鈑機軸
鈑機連動件軸
心棒(四孔)
氣瓶頂針
心棒蓋
槍管
心棒壓簧墊圈
氣瓶頂針迫緊
槍管華司
心棒壓簧墊圈
鈑機連桿
擊槌軸
槍柄扣環
保險左壓簧
撞針扭簧
鈑機連桿扭簧
彈匣卡榫壓簧
擊槌扭簧
緩衝扭簧
心棒壓簧
彈匣壓簧
槍管回位壓簧
內六角 M5-P0.8X8黑
⊕2.3X6尖.錏.熱
⊕皿 2.3X5束黑熱
⊕皿 2.3X6束黑熱
⊕皿 2.3X8束黑熱
六角螺帽M5-0.8
E型扣環
內六角止付螺絲
子彈迫緊
O形環
∮0.8X∮11.3id
O型環 1X4
O型環 1X5
O型環 1.45X6.9id
O形環 S-8
內槍管組件
鈑機組件
氣瓶頂針組件
SAFETY ACCESSORY
GRIP
VALVE PACKING
MAGAZINE FOLLOWER
FRONT BARREL CAP
INNER BARREL CAP
FRAME (L)
FRAME (R)
TRIGGER
SAFETY(L)
FIRING PIN
TRIGGER CONNECTOR
SAFETY LOCK
MAGAZINE CATCH
HAMMER
BARREL TOW
MAGAZINE
MAGAZINE BASE
ACCESSORY
BEARING
FIRING PIN AXLE
TRIGGER PIN
VALVE
PUNCTURE VAVLE
VALVE CAP
BARREL
VALVE SPRING GASKET
TRIGGER
CONNECTOR PIN
PUNCTURE VAVLE
PACKING
BARREL WASHER
VALVE SPRING
GASKET
TRIGGER BAR
HAMMER AXIS
GRIP BUCKLE
SAFETY SPRING (L)
FIRING PIN SPRING
TRIGGER BAR SPRING
HAMMER SPRING
PUMPER SPRING
VALVE SPRING
MAGAZINE SPRING
BARREL SPRING
MAGAZINE CATCH
SPRING
SOCKET SCREW
M5-P0.8X8
SCREW2.3X6
SCREW 2.3X5
SCREW 2.3X6
SCREW 2.3X8
HAX NUT M5-0.8
E-RING
MAGAZINE BOTTOM CAP
RUBBER CHAMBER
O-RING0.8X11.3id
O-RING 1X4
O-RING 1X5
O-RING 1.45X6.9id
O-RING S-8
INNER BARREL UNIT
TRIGGER UNIT
PUNCTURE VAVLE UNIT
-
1
-
2
