Dell 1800MP Projector 取扱説明書

カテゴリー
データプロジェクター
タイプ
取扱説明書
www.dell.com | support.dell.com
Dell™ 1800MP Projector
Owner’s Manual
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you
make better use of your projector.
NOTICE: A NOTICE indicates either potential damage to
hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property
damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2006 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell
Inc. is strictly forbidden.
Trademarks used in this text: Dell , the DELL logo, Dimension OptiPlex Dell
Precision Latitude Inspiron DellNet PowerApp PowerEdge PowerConnect
PowerVault are trademarks of Dell Inc.; DLP and Texas Instruments
trademarks of Texas Instruments Corporation; Microsoft Windows
registered trademarks of Microsoft Corporation; Macintosh
trademark of Apple Computer, Inc.
Other trademarks and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Restrictions and Disclaimers
The information contained in this document, including all instructions, cau-
tions, and regulatory approvals and certifications, is based upon statements
provided to Dell by the manufacturer and has not been independently verified
or tested by Dell. Dell disclaims all liability in connection with any deficien-
cies in such information.
All statements or claims regarding the properties, capabilities, speeds, or
qualifications of the part referenced in this document are made by the
manufacturer and not by Dell. Dell specifically disclaims any knowledge of the
accuracy, completeness, or substantiation for any such statements.
Model 1800MP
September 2006 Rev. A00
Contents 3
Contents
1 Your Dell Projector . . . . . . . . . . . . . . . . . . 5
About Your Projector . . . . . . . . . . . . . . . . . 6
2 Connecting Your Projector . . . . . . . . . . . . 7
Connecting to a Computer . . . . . . . . . . . . . . . . . 8
Connecting to a DVD Player
. . . . . . . . . . . . . . . . 9
Connecting a DVD Player with an S-video Cable
. . . 9
Connecting a DVD Player with a Composite Cable
. 10
Connecting a DVD Player with a Component Cable
11
Professional Installation Options: . . . . . . . . . . 12
3 Using Your Projector . . . . . . . . . . . . . . . . 13
Turning Your Projector On . . . . . . . . . . . . . . . . 13
Turning Your Projector Off
. . . . . . . . . . . . . . . . 13
Adjusting the Projected Image
. . . . . . . . . . . . . 14
Raising the Projector Height
. . . . . . . . . . . . 14
Lowering the Projector Height
. . . . . . . . . . . 14
Adjusting the Projector Zoom and Focus
. . . . . . . . 15
Adjusting Projection Image Size . . . . . . . . . . . . 16
Using the Control Panel
. . . . . . . . . . . . . . . . . 17
4 Contents
Using the Remote Control . . . . . . . . . . . . . . . . 19
Using the On-Screen Display
. . . . . . . . . . . . . . 20
Main Menu
. . . . . . . . . . . . . . . . . . . . . 21
Input Select
. . . . . . . . . . . . . . . . . . . . . 21
Auto-Adjust
. . . . . . . . . . . . . . . . . . . . . 21
Set Up . . . . . . . . . . . . . . . . . . . . . . . . 22
PICTURE (in PC Mode)
. . . . . . . . . . . . . . . 23
PICTURE (in Video Mode)
. . . . . . . . . . . . . 23
DISPLAY (in PC Mode) . . . . . . . . . . . . . . . 24
DISPLAY (in Video Mode)
. . . . . . . . . . . . . 25
LAMP
. . . . . . . . . . . . . . . . . . . . . . . . 25
LANGUAGE . . . . . . . . . . . . . . . . . . . . . 26
Preferences
. . . . . . . . . . . . . . . . . . . . 27
4 Troubleshooting Your Projector . . . . . . . 31
Changing the Lamp . . . . . . . . . . . . . . . . . . . 35
5 Specifications . . . . . . . . . . . . . . . . . . . . . 37
Contacting Dell . . . . . . . . . . . . . . . . . . . . 43
Appendix: Regulatory Notices . . . . . . . . . 71
FCC Notices (U.S. Only) . . . . . . . . . . . . . . . 71
NOM Information (Mexico Only)
. . . . . . . . . . 72
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Your Dell Projector 5
1
Your Dell Projector
Your projector comes with all the items shown below. Ensure that you have all the
items, and contact Dell if anything is missing.
Package Contents
1.8m power cord (3.0m in Americas) 1.8m VGA cable (VGA to VGA)
Batteries (2) Remote control
Documentation Carrying case
6 Your Dell Projector
About Your Projector
1 Remote control receiver
2 Elevator button
3 Lens
4 Focus ring
5 Zoom tab
6 Power cord connector
Connecting Your Projector 7
2
Connecting Your Projector
Monitor loop through from VGA-A In to VGA-A Out only.
1 Audio output connector
2 Audio input connector
3 VGA-B In connector
4 VGA-A In connector
5 S-video connector
6 Video input connector
7 VGA-A out connector
8 USB remote connector
9 RS232 connector
10 Kensington lock hole
8 Connecting Your Projector
Connecting to a Computer
The USB cable is not provided by Dell.
Consult a professional installer for the cable.
1 Power cord
2 VGA to VGA cable
3 USB cable
Connecting Your Projector 9
Connecting to a DVD Player
Connecting a DVD Player with an S-video Cable
The S-video cable is not provided by Dell.
Consult a professional installer for the cable.
1 Power cord
2 S-video cable
10 Connecting Your Projector
Connecting a DVD Player with a Composite Cable
The Composite cable is not provided by Dell.
Consult a professional installer for the cable.
1 Power cord
2 Composite video cable
Connecting Your Projector 11
Connecting a DVD Player with a Component Cable
The VGA to YPbPr cable is not provided by Dell.
Consult a professional installer for the cable.
1Power cord
2 VGA to YPbPr cable
12 Connecting Your Projector
Professional Installation Options:
Connecting a Computer with a RS232 Cable
The RS232 cable is not provided by Dell.
Consult a professional installer for the cable.
1Power cord
2 RS232 cable
Using Your Projector 13
3
Using Your Projector
Turning Your Projector On
NOTE: Turn on the projector before you turn on the source. The power button
light blinks blue until pressed.
1
Remove the lens cap.
2
Connect the power cord and appropriate signal cables. For information about
connecting the projector, see "Connecting Your Projector" on page 7.
3
Press the power button (see "Using the Control Panel" on page 17 to locate the
power button). The Dell logo displays for 30 seconds.
4
Turn on your source (computer, DVD player, etc.). The projector automatically
detects your source.
If the "Searching for signal..." message appears on the screen, ensure
that the appropriate cables are securely connected.
If you have multiple sources connected to the projector, press the Source button
on the remote control or control panel to select the desired source.
Turning Your Projector Off
NOTICE: Unplug the projector after properly shutting down as explained in the
following procedure.
1
Press the power button.
2
Press the power button again. The cooling fans continue to operate for 60 seconds.
3
Disconnect the power cord from the electrical outlet and the projector.
NOTE: If you press the power button while the projector is running, the "Power
Off the Lamp?" message appears on the screen. To clear the message, press any
button on the control panel or ignore the message; the message disappears after 3
seconds.
14 Using Your Projector
Adjusting the Projected Image
RAISING THE PROJECTOR HEIGHT
1
Press the elevator button.
2
Raise the projector to the desired display angle, and then release the button to
lock the elevator foot into position.
3
Use the tilt adjustment wheel to fine-tune the display angle.
LOWERING THE PROJECTOR HEIGHT
1
Press the elevator button.
2
Lower the projector, and then release the button to lock the elevator foot into
position.
1 Elevator button
2 Elevator foot
3 Tilt adjustment wheel
Using Your Projector 15
Adjusting the Projector Zoom and Focus
CAUTION: To avoid damaging the projector, ensure that the zoom lens and
elevator foot are fully retracted before moving the projector or placing the
projector in its carrying case.
1
Rotate the zoom tab to zoom in and out.
2
Rotate the focus ring until the image is clear. The projector focuses at distances
from 4.9 ft to 39.4 ft (1.5 m to 12.0 m).
1 Zoom tab
2 Focus ring
16 Using Your Projector
Adjusting Projection Image Size
Using Your Projector 17
Using the Control Panel
Screen
(Diagonal)
Max. 38.1"
(96.8cm)
86.4"
(219.4cm)
139.8"
(355.0cm)
195.7"
(497.0cm)
249.0"
(632.5cm)
304.9"
(774.5cm)
Min. 34.7"
(88.0cm)
78.5"
(199.5cm)
127.1"
(322.7cm)
177.9"
(451.8cm)
226.4"
(575.0cm)
277.2"
(704.1cm)
Screen Size
Max.
(WxH)
30.5"X22.9" 69.1"X51.8" 111.8"X83.9" 156.5"X117.4" 199.2"X149.4" 243.9"X183.0"
(77.5cm X
58.1cm)
(175.6cm X
131.7cm)
(284.0cm X
213.0cm)
(397.6cm X
298.2cm)
(506.0cm X
379.5cm)
(619.6cm X
464.7cm)
Min.
(WxH)
27.7" X
20.8"
62.8" X
47.1"
101.6" X
76.2"
142.3" X
106.7"
181.1" X
135.8"
221.8" X
166.3"
(70.4cm X
52.8cm)
(159.6cm X
119.7cm)
(258.2cm X
193.6cm)
(361.4cm X
271.1cm)
(460.0cm X
345.0cm)
(563.3cm X
422.5cm)
Distance 4.9' (1.5m) 11.2' (3.4m) 18.0' (5.5m) 25.3' (7.7m) 32.2' (9.8m) 39.4' (12.0m)
* This graph is for user reference only.
1 Power Turn the projector on and off. For more
information, see "Turning Your Projector On" on
page 13 and "Turning Your Projector Off" on
page 13.
1
3
5
2
6
9
8
11
11
4
7
10
10
18 Using Your Projector
2 TEMP warning light
A solid orange TEMP light indicates that the
projector has overheated. The display
automatically shuts down. Turn the display on
again after the projector cools down. If the
problem persists, contact Dell.
A blinking orange TEMP light indicates that a
projector fan has failed and the projector
automatically shuts down. If the problem
persists, contact Dell.
3 Source Press to toggle through Analog RGB, Composite,
Component-i, S-video, and Analog YPbPr sources
when multiple sources are connected to the
projector.
4 Keystone adjustment Press to adjust image distortion caused by tilting
the projector. (±15 degrees)
5 Resync Press to synchronize the projector to the input
source. Resync does not operate if the on-screen
display (OSD) is displayed.
6 Menu Press to activate the OSD. Use the directional
keys and Menu button to navigate through the
OSD.
7 and buttons Press to adjust the OSD setting.
8 Enter Press to confirm the selection item.
9 Keystone adjustment Press to adjust image distortion caused by tilting
the projector. (±15 degrees)
10 Up and Down Press to select the OSD items.
11 LAMP warning light If the LAMP light is solid orange, replace the
lamp. If the LAMP light is blinking orange, the
system has failed and the projector will
automatically shut down. If this problem persists,
contact Dell.
Using Your Projector 19
Using the Remote Control
1 Power Turn the projector on and off. For more
information, see "Turning Your Projector On" on
page 13 and "Turning Your Projector Off" on
page 13.
2 Press to adjust the OSD setting.
3 Down button Press to select OSD items.
4 Mute Press to mute or unmute the projector speaker.
5 Volume Press to increase the volume.
6 Page Press to move to previous page.
7 Page Press to move to next page.
1
2
3
4
5
6
7
8
9
19
19
18
18
17
17
16
16
15
15
14
14
13
13
11
11
10
10
12
12
20 Using Your Projector
Using the On-Screen Display
The projector has a multi-language On-Screen Display (OSD) that can be
displayed with or without an input source present.
In the Main Menu, press or to navigate through the tabs.
In the submenu, press or to make a selection. When an item is selected, the
color changes to dark gray. Use or on the control panel or the remote
control to make adjustments to a setting.
8 Video mode The Dell 1800MP Micro-projector has preset
configurations that are optimized for displaying
data (PC Graphics) or video (movies, games,
etc.). Press Video Mode button to toggle between
PC mode, Movie mode, Game Mode, sRGB, or
CUSTOM mode (for user to setup and save
preferred settings). Pressing the Video Mode
button once will show the current display mode.
Pressing the Video Mode button again will switch
between modes.
9 Blank screen Press to hide the image, press again to resume
display of the image.
10 LED light LED indicator.
11 Up button Press to select OSD items.
12 Enter button Press to confirm the selection.
13 Press to adjust the OSD setting.
14 Menu Press to activate the OSD.
15 Volume Press to decrease the volume.
16 Keystone adjustment Press to adjust image distortion caused by tilting
the projector. (±15 degrees)
17 Source Press to switch between Analog RGB, Digital
RGB, Composite, Component-i, S-video, and
Analog YPbPr sources.
18 Auto adjust Press to synchronize the projector to the input
source. Auto adjust does not operate if the OSD
(On-Screen Display) is displayed.
19 Keystone adjustment Press to adjust image distortion caused by tilting
the projector. (±15 degrees)
1 / 1